Used Makino for sale (34)

Condition: used, Year of construction: 2016, Makino A51NX in very good condition, including a new ATC tool changer and Cubes. Approx. 11,000 hours of cutting time. Capacity & Travels: Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Workpiece: ∅ 630 mm × 900 mm Max. Payload Capacity: 400 kg Spindle: Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Motion & Feed Rates: Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cutting Feedrate: 50,000 mm/min Lrodpfxszg N E Hs Acnjn Axis Acceleration: 1G B-Axis Indexing: Full 4th axis, Direct Drive (0.001-degree increments) Tooling: ATC (Automatic Tool Changer) Capacity: 60 tools Tool-to-Tool Time: 0.9 seconds Max. Tool Diameter / Weight: 170 mm / 12 kg 04003 HSK-A63 Spindle – Replaces the standard ISO50 interface. Features a double taper, full face contact, and hollow shank interface. Tool clamping force is higher than 44kN; HSK tool holders are required. 14017 HSK holders for 60 Tool ATC 26001 Moire Scale Feedback X, Y, Z-Axis Increments 0.05µm, positioning tolerance Tp = 0.006mm (ISO 230-2). 29006 Through Spindle Coolant 3.0MPa – Provides TSC flow of 30 l/min at 3.0MPa, replacing the standard 1.5MPa. Air through the spindle is possible. The pressure data refers to the output flange of the pump. 29009 Flow Switch for Through Spindle Coolant – Monitors through-spindle coolant flow. The machine will feed hold if the flow is below a preset level. Note: Recommended option for filtration systems to prevent tool damage. 31002 Air curtain for splash guard window – Located in the middle of the operator-side window, this air curtain prevents chips and coolant from obstructing the view. 37000 Broken tool sensor outside machining area (BTS) – Tool breakage detection for centric tools (tool diameter 1-40mm, tool length 65 - 430mm). Length measurement is performed using a movable probe. The measurement takes place in the ready position for a tool change, outside the machining area. Accuracy ± 2mm. If there is a difference between the measurement before and after machining, an alarm is triggered automatically. 37101L Automatic Workpiece Measuring Device (RENISHAW OMP60) – Three-coordinate measuring probe from RENISHAW with automatic coordinate correction. The signal is transmitted via infrared. Tolerance approx. 0.005mm. 14 automatic measurement cycles are available as pre-programmed cycles in the program memory. Note: requires 13m. Control Options: 60001 Automatic Corner Override (G62) – Automatically decelerates the cutter at a corner depending on the corner angle, in order to maintain the cutting rate per unit time. 62007 Run hour and parts quantity display. 63034 DATA CENTER Storage Type B (total: 800MB) – Communication card with internal 800MB removable flash RAM card used for storing and executing NC data (of subprograms) for high-speed, high-definition finishing and supporting SGI capabilities. CNC programs can be transferred to and from a CAD/CAM system from the operator's pendant by FTP get and put commands over an Ethernet cable. 66003 Additional 48 Work Offsets (G54.1 P1-P48) – Allows for 48 work coordinate systems, simplifying multiple part fixtures. 68010 600 Macro Common Variables – Variable numbers 100-199 are reset and cleared when the power is turned off, while 500-999 are permanent. Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Payload Capacity: 400 kg Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cut...

Condition: used, Year of construction: 2004, Horizontal machining center Manufacturer: Makino Type: a51-A60 Year of manufacture: 2004 Control: CNC FANUC System 16 iM Travel distances: X/Y/Z: 560 x 560 x 500 mm Distance from table center to spindle nose: 70 – 570 mm Maximum swivel height above the pallet surface: 900 mm Permissible swivel range in the working area: 630 mm Tool magazine: 60 storage locations Maximum load weight: 180 kg T-slot, 4-digit, freely assignable Tool change time: 0.9 sec. Maximum tool dimensions: Ø 70 mm, 360 mm long Maximum tool weight: 8 kg Spindle unit 50 – 12,000 rpm Spindle unit with tool holder for tapered hollow shanks according to DIN 69893 HSK-A63 Tool clamping force: 29 kN Pallet changer system, integrated into the machine Pallet change time: 7 sec. Pallet changer with storage of 2 pallets in alternating sequence on a storage station Pallet holder rotatable, index 90° division 0 position electrically controlled. Maximum permissible load weight: 400 kg Pallet size: 400 x 400 mm High-speed machining Contour milling with feed rates up to 40,000 mm/min. Function can be used for milling in 3 axes X, Y, and Z 2 ½ axis operation (X/Y axis circular, Z axis linear) for thread and contour milling Direct thread cutting through synchronization of the feed drive of the Z axis via pulse encoder in the spindle motor Maximum speed: n = 4,000 rpm Feed drive with AC servo motors Rapid traverse speeds X, Y, Z axis = 1 … 50,000 mm/min. Feed rates X, Y, Z axis = 1 .. 40,000 mm/min. Manual operation, freely movable, via direction keys Coolant system Chip and splash guard central chip/flushing system Machine light Rotating warning light, 3-color Total weight: 7,800 kg Lodpfx Aozc Ifrjcnjrn Space requirement approx.: 11.5 m2 Overall height approx.: 2.7 m 2 machines available! 23626

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, The machine is in good technical condition. X-axis travel: 900 mm Y-axis travel: 500 mm Z-axis travel: 450 mm 4 axes Fanuc FS31i control system Table: -External length 1000 mm Lsdszgvzbepfx Acnern -External width 500 mm -Table load 1000 kg New electric spindle installed 4 years ago. Tool magazine for 30 tools, including tool holders. The machine operated on a single shift. Inspection during operation is possible by prior arrangement.

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, X-axis: 650 mm Y-axis: 325 mm Z-axis: 350 mm B-axis: 130 degrees C-axis: 360 degrees Lsdpfx Ajzapp Hjcnjrn Spindle speed: 30,000 rpm Spindle interface: HSK 50 Tool changer: 60 positions Control system: Makino Professional 5 Includes hybrid length measuring system Includes measuring probe Includes approximately 60 HSK 50 tool holders (MST + Rego Fix) Spindle has been replaced Ball screws for X and Y axes replaced in 2024 Machine currently has approximately 32,000 spindle hours and is still in active production Available from approximately week 46/2026 An inspection with the machine powered on can be arranged at any time.

Condition: used, Year of construction: 2014, functionality: fully functional, number of spindles: 1, number of slots in tool magazine: 60, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Technical specification: - Horizontal spindle - Spindle HSK-A63 - Spindle torque 240 Nm (to be confirmed) - 4-axis machining - ATC for 60 tools - Pallet changer (2 pallets) - Pallet size 500x500 mm - Coolant chiller - Coolant filtration system by Knoll Lodpfx Aeyrfxhecnjrn - Coolant pressure 50 bar through spindle - Fanuc control system - Chip conveyor - Robot interface - Linear measuring systems (scales) - Manufactured in 2014

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, operating hours: 55,569 h, travel distance X-axis: 560 mm, travel distance Y-axis: 560 mm, travel distance Z-axis: 560 mm, number of slots in tool magazine: 126, controller model: Fanuc 16 MC Professional 3, spindle speed (max.): 20,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel in X-axis: 560 mm Travel in Y-axis: 560 mm Travel in Z-axis: 560 mm Spindle speed: 20,000 rpm Torque: max. 167 Nm Tool interface: HSK-A63 DIN 69893 Tool magazine: 126 positions Tool change time: 1 s Max. tool diameter: 80 mm Max. tool length: 300 mm Lredpfx Ajzb Ewpocnsn Distance from spindle nose to table: 150 - 710 mm Distance from table top to spindle center: 80 - 640 mm Pallet size: 400 x 400 mm Pallet load: 400 kg Pallet change time: 7 s Rotary table indexing: 1° Table rotation speed: 5000 rpm Spindle drive: 22 kW Feed rate: max. 40,000 mm/min Rapid traverse rate: 40,000 mm/min MACHINE DETAILS Control system: Fanuc 16 MC Professional 3 Total power consumption: 64 kW Dimensions & Weight Footprint: approx. 9.0 x 3.0 x 2.8 m Machine weight: approx. 15 t Operating hours Spindle hours: 55,569 h Program runtime: 66,600 h Power-on time: 163,411 h

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: 80.4308.0097, travel distance X-axis: 900 mm, travel distance Y-axis: 800 mm, travel distance Z-axis: 970 mm, controller model: FANUC Professional 3, spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 900 mm Travel range, Y-axis: 800 mm Travel range, Z-axis: 970 mm Pallet size: 630 mm × 630 mm Number of pallets: 2 Max. workpiece weight: approx. 1,200 kg Spindle connection: HSK-A100 Max. spindle speed: 12,000 rpm Tool magazine: 188 positions Tool change time: approx. 1.7 s Rapid traverse: up to 50 m/min Lrjdpfezb Efyjx Acnon MACHINE DETAILS Control system: FANUC Professional 3 Machine weight: approx. 18 t EQUIPMENT Dual-pallet system Large 188-position tool magazine Automatic tool changer Through-spindle coolant / coolant system Chip conveyor NC rotary table Network/DNC connection Note: The machine was previously connected to a pallet loading station. The pallets can, of course, also be loaded manually.

Condition: ready for operation (used), Year of construction: 1998, travel distance X-axis: 300 mm, travel distance Y-axis: 250 mm, travel distance Z-axis: 250 mm, total height: 2,290 mm, overall weight: 3,200 kg, controller manufacturer: MAKINO, controller model: MGF, number of axes: 3, This 3-axis Makino EDNC 30 die-sinking EDM machine was manufactured in 1998. It features travel paths of 300mm in X, 250mm in Y, and 250mm in Z, a table size of 500 × 350 mm, and can handle a maximum workpiece weight of 500 kg. Consider the opportunity to buy this Makino EDNC 30 die-sinking EDM machine. Contact us for more information about this machine. Machine Benefits Ljdpfxex U U Hue Acnern Technical Machine Benefits • Total area: width 3000 mm, y 2800 mm • Power: 12 kva, 400 v, 12 a • Table size: 500 mm x 350 mm • Tool positions: 8 • Polishing edm is possible with this machine. Extra Information Polishing EDM is possible with this machineFaulty circuit board (machine won't start up) Dimensions Machine Depth 2000 mm

Condition: like new (used), Year of construction: 2016, operating hours: 30,592 h, functionality: fully functional, travel distance X-axis: 550 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 500 mm, rapid traverse X-axis: 48 m/min, rapid traverse Y-axis: 50 m/min, rapid traverse Z-axis: 50 m/min, controller manufacturer: FANUC, controller model: Professional 5, workpiece length (max.): 650 mm, workpiece width (max.): 500 mm, workpiece height (max.): 500 mm, workpiece diameter (max.): 650 mm, workpiece weight (max.): 350 kg, total height: 3,200 mm, total length: 3,550 mm, total width: 2,900 mm, table load: 350 kg, rotary table diameter: 500 mm, overall weight: 15,700 kg, spindle speed (min.): 14,000 rpm, operating hours of spindle: 30,592 h, Year of construction: 2016 CNC controller: FANUC Professional 5 Axes X-axis travel mm: 550 Y-axis travel mm: 1000 Z-axis travel mm: 500 C-axis degrees: 360 (continuous rotation) / rotary encoder A-axis degrees: 150 (+30 120º) rotary encoder Feed rates m/min: X:32; Y,Z:40 Rapid traverse m/min: X,A,C:48; Y,Y:50; A,C:18 Worktable Table dimensions mm: 500 Maximum workpiece size (D x H) mm: 650x500 Max. workpiece weight kg: 350 Spindle Spindle speed rpm: 14000 Tool system Tool holder: HSK-A63 Tool magazine slots: 323 Lsdpfey Icu Tjx Acnern Tool changer: Pinza doble Max. Tool Diameter 70 With occupied neighboring places mm: 140 Max. Tool Length mm: 300 Max tool weight kg: 8 Equipment Electronic Handwheel Chip conveyor Measuring probe Machine running times Under power: 63813h Spindle Working: 30592h Basic machine dimensions / weight Length mm: 3550 Width mm: 2900 Height mm: 3200 Weight kg: 15700

Condition: used, Year of construction: 2018, Technical details: x-travel: 650 mm y-travel: 450 mm z-travel: 420 mm control: MAKINO Hyper i U-axis: ± 75 mm V-axis: ± 75 mm max. size of workpiece LxWxH: 1000 x 800 x 400 mm workpiece weight: max. 1500 kg Table dimensions: 910 x 710 mm weight of the machine ca.: 5 t Dimensions (L/W/H): 3 x 3 x 2,3 mm Accerories Memory 10 GB Ljdoy I Ak Ispfx Acnsrn Ethernet I/P Interface Wire EDM in good condition. *

Condition: ready for operation (used), Year of construction: 2016, travel distance X-axis: 185 mm, travel distance Y-axis: 125 mm, travel distance Z-axis: 200 mm, total height: 850 mm, total width: 780 mm, wire diameter (max.): 0.3 mm, overall weight: 250 kg, product length (max.): 800 mm, number of axes: 3, wire diameter (min.): 0.1 mm, This 5-axis Makino U6 HEAT was manufactured in 2016. It features an impressive X-axis travel of 650 mm, Y-axis travel of 450 mm, and Z-axis travel of 420 mm. The machine has a maximum workpiece size of 1,000 x 800 x 400 mm and can handle a maximum workpiece weight of 1,500 kg. If you are looking to get high-quality wire EDM capabilities, consider the Makino U6 HEAT wire EDM machine we have for sale. Contact us for further details. • Spindle speed: 150–2000 rpm • Spindle drive power: 0.75 kW (at 100% duty cycle) Lrjdpfjy Hi T Tox Acnen • Tool changer: Automatic, 10 stations • Tool holder: SK 30 (DIN 2080 / DIN 69871) • Feed rate (X/Y/Z): 5–500 mm/min • Rapid traverse: 500 mm/min • Clamping area: 420 x 125 mm • Max. workpiece weight: 10 kg • Power supply: 230 V / 50 Hz • Availability: Not specified

Condition: used, Year of construction: 2004, Makino A66E with Fastems 10 pallet system built in container. Length of the working table 500.4 mm Width of the working table 500.4 mm Maximum table load 700 kg Antalet verktyg i magasinet 136 st Maximum spindle speed 14000 rpm Travel length X-axis (mechanical feed) 729 mm Travel length Y-axis (mechanical feed) 729 mm Lrsdpfoy D Sirex Acnen Travel length Z-axis (mechanical feed) 797.6 mm Maximum feed rate in X-axis 1250.1 mm/s Maximum feed rate in Y-axis 1250.1 mm/s Maximum feed rate in Z-axis 1250.1 mm/s

Condition: ready for operation (used), Year of construction: 2001, A horizontal CNC machining center Makino is available. Travel path X/Y/Z: 560mm/560mm/600mm, pallet dimensions X/Y: 400mm/400mm, max. workpiece weight: 500kg, indexing: 0.001°, rapid traverse: 84m/min, feed rate: 50m/min. Machine dimensions X/Y/Z: approx. 4650mm/1950mm/2850mm, weight: approx. 8600kg, control system: Fanuc System 16iM/Makino Professional 3. Documentation available. An on-site inspection is possible. Ljdpoy S A Nrjfx Acnern

Condition: like new (used), Year of construction: 2011, travel distance X-axis: 550 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 500 mm, feed length X-axis: 550 mm, feed length Y-axis: 1,000 mm, feed length Z-axis: 500 mm, controller manufacturer: FANUC Professional 5, workpiece length (max.): 650 mm, workpiece width (max.): 500 mm, workpiece weight (max.): 350 kg, total height: 3,200 mm, total length: 3,550 mm, total width: 3,200 mm, overall weight: 15,700 kg, spindle speed (min.): 20,000 rpm, tool length: 300 mm, tool diameter: 70 mm, tool weight: 8,000 g, CNC controller: FANUC Professional 5 Axes X-axis travel mm: 550 Y-axis travel mm: 1000 Z-axis travel mm: 500 C-axis degrees: 360 (continuous rotation) / rotary encoder A-axis degrees: 150 (+30 120º) rotary encoder Feed rates m/min: X:32; Y,Z:40; Rapid traverse m/min: X,A,C:48; Y,Y:50; A,C:18 Worktable Table dimensions mm: 500 Maximum workpiece size (D x H) mm: 650x500 Max. workpiece weight kg: 350 T-Slot version: 4x185H8 Spindle Spindle speed rpm: 20000 Tool system Tool holder: HSK-A63 Tool magazine slots: 323 Tool changer: pinza doble Max. Tool Diameter: 70 With occupied neighboring places mm: 140 Tool Magazine: Matrix Max. Tool Length mm: 300 Max tool weight kg: 8 Equipment Electronic Handwheel Chip conveyor Custom Macro common variables (100) Synchronized tapping Preparación para trabajar con robot Robot EROWA Lsdpfoy Ddq Uex Acnorn Helical interpolation Custom Macro common variables (100) Machine running times Spindle Working: 0h (Retrofited) Basic machine dimensions / weight Length mm: 3550 Width mm: 2900 Height mm: 3200 Weight kg: 15700

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: 80-4310-0003, travel distance X-axis: 730 mm, travel distance Y-axis: 730 mm, travel distance Z-axis: 800 mm, rapid traverse X-axis: 50 m/min, rapid traverse Y-axis: 50 m/min, rapid traverse Z-axis: 50 m/min, torque: 245 Nm, controller manufacturer: Fanuc, controller model: System 16 iM, workpiece length (max.): 600 mm, workpiece width (max.): 300 mm, workpiece height (max.): 600 mm, overall weight: 17,000 kg, spindle speed (max.): 9,000 rpm, operating hours of spindle: 16,000 h, spindle nose: 350, number of spindles: 1, number of slots in tool magazine: 89, mount diameter: 100 mm, tool weight: 20,000 g, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Further detailed information can be found in the attached documents and photos. Sale price upon request, price negotiable. Ljdpoy Nm E Ssfx Acnorn

Condition: used, Year of construction: 2020, Two machines from year of manufacture 2020 (G5 i) and one machine from 2022 (G5) available. Includes hydraulic unit, oil cooler, and air dryer Initial commissioning of the 2020 machines in March/May 2022, the 2022 machine in March 2023. The machining center can be used for grinding, milling, and drilling of metallic workpieces. A standard integrated dressing unit is included. This machining center is used for hard grinding and finish boring of holes in discs and flanges of precision planetary gear units. Machine Description: Makino Model G5 i Grinder Universal Machining Center With creep feed grinding function Makino Professional 5 Control System Machine Specifications (according to manufacturer): Travel: Column X-axis: 520 mm Spindle Y-axis: 560 mm Table Z-axis: 600 mm Spindle center to top of pallet: 80 – 640 mm Spindle nose to center of pallet: 70 – 670 mm Feed rates: Smallest increment: 0.001 mm Jog operation: 1 - 8,000 mm/min Machining feed: 1 - 48,000 mm/min Rapid traverse: 48 m/min Spindle: Spindle taper: ISO 40 Spindle motor (high torque): 18.5 / 22 kW AC Speed (2 ranges): 50 – 12,000 rpm Automatic tool changer Lredpfjywgh Nex Acnsn Machine weight: 8,450 kg Controlled Axes: 5-axis simultaneous Special equipment for VIPER grinding: Dressing unit Rotary dressing unit (quick-change) – electric, incl. holder (52 mm) Electrical interface for dresser Workpiece clamping: Erowa ER-029392 Power Chuck Clamping/release control including pressure display Coolant preparation and supply: Water-based coolant filtration system Transfer tank High-pressure pump Self-tilting chip bin Coolant supply bridge Extraction unit including ductwork Makino interface for coolant system Makino interface for extraction system Coolant monitoring (pressure, flow, temperature) Programmable coolant nozzle (PCN) – through spindle, nozzle, base, and shower PCN nozzle assembly Other: Automatic workpiece measuring device (RMP600) Point Master unit (manual measuring probe) Bench Master Air dryer Special I/O interface Machine anchoring set FANUC warranty (2 years) C&F costs UK/Euro transformer High-speed rotary work spindle (100 rpm) Time-delayed splash guard Oil lubrication system for ballscrews and linear guides Programmable coolant nozzle for grinding wheels (PCN) Reinforced splash guard door Automatic front door (AWC) with light curtain Signal lights (3-color) Halogen work lamp (1 pc) Safety interlock package Optional equipment: Easy-Grind Max NC incl. HMI and Machine Manager Scale system X, Y, Z axes (0.05 μm) Switching the display language from English to German Freewheel function of rotary axes during operation Project management by NCMT and Melior Motion Easy-Grind Max+ (single station solution, custom configured)

Condition: excellent (used), MAKINO V 33i Graphite is a 3‑axis machining center designed for precision, high accuracy and reliability. Capacities: table 750×450 mm with 4 T‑slots 18H8 at 100 mm, table load 300 kg; travels X650 Y450 Z350 mm; workpiece max L750 W635 H250 mm. Specs: spindle HSK E50 (nose–table 150–500 mm), stepless 300–30,000 t/min, torque 23.1 Nm; spindle power 17/13 kW; feed 1–20,000 mm/min, rapid 20 m/min; tool magazine 60 places, tool Ø max 80 mm, length 250 mm, tool change 4.8 s; 3×400 V 50 Hz, air 4–8 bar; machine ≈7700 kg, footprint 2330×2325×2600 mm, installed power 50 kVA. Accessories: lamp, oil‑mist extractor, spindle cooling, EROWA EASY ROBOT loader, status light. Achieves tight tolerances; suits automotive, watchmaking, tooling, aerospace and medical applications. Lrsdpfsyxn Awsx Acnon

Condition: ready for operation (used), Year of construction: 2001, operating hours: 11,472 h, travel distance X-axis: 600 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 400 mm, controller manufacturer: FANUC, controller model: System 16iM, spindle speed (max.): 30,000 rpm, spindle motor power: 15,000 W, number of axes: 3, This 3-axis Makino SNC 64-A15 was manufactured in 2001. It features a main spindle speed ranging from 300 to 30,000 rpm and a spindle motor power of 15 kW. The machine is equipped with a tool magazine holding 15 positions and offers a feed rate of up to 16,000 mm/min. If you are looking to get high-quality graphite and metal machining capabilities, consider the Makino SNC 64-A15 vertical machining centre we have for sale. Contact us for further details. • Electrical • Operating voltage: 400 V • Frequency: 50 Hz • Phases: 3-phase • Nominal current: 90 A • Recommended supply fuse: 100 A (slow-blow/time delay) • Supply cable size: 35 mm² copper • Wiring diagram: 4036 EP 0024 • CNC / Control • Microcomputer control: Professional A • CNC: FANUC System 16iM • DNC connection: Data server interface • Integrated IC memory: 160 MB • Interpolation: NURBS • Programs: 125 main and sub-programs storable simultaneously • Coordinate input: Polar coordinate input available • High-speed contour control: Super-GI • Processor: RISC for fast 3D machining calculations • Mechanical construction • Machine frame: Cast iron welded construction • Axes layout: Cross table system (X, Y); Z-axis console type • Guides: Preloaded ball linear guideways • Thermal stability: Oil circulation cooling for spindle temperature stabilization • Axis performance • Rapid traverse: up to 16,000 mm/min • Simultaneous machining: 3-axis contour milling • Contour accuracy: High (Super-GI control) • Spindle • Tool holder: HSK-A63F • Torque: 21 Nm • Front bearing diameter: 55 mm • Tool system • Tool magazine capacity: 15 tools • Tool breakage monitoring: Yes • Automatic tool changing: Yes • Applications / capabilities • Graphite electrode milling (incl. long tools) • Copper electrode machining • Hardened steel milling • Designed for automatic production sequences • Optimized surface finish capability Lredpfx Aceyvq Drjnen • Contour-accurate 3D milling capability • Standard/integrated systems • Graphite dust extraction system • Dust removal via: air blast, spindle suction, tool suction • Filter system with automatic collection container • Minimum quantity lubrication (MQL) • Designed for high-speed graphite machining • Suitable for hardened mold cores

Year of construction: 2018, condition: used, We are selling a new unused but defective tool magazine with tool changer for a Makino PS 95. The magazine body was broken in two parts with a crane hook during unloading of the machine from its transport box. Also some tool pots are damaged. Can be repaired or used as spare parts * Ledpfxsvfdvbj Acnern

Condition: used, Year of construction: 2005, Technical details: Lredpfevc Adlsx Acnon size of pallet: 400x400 mm numbers of pallets: 15 table load: 400 kg weight of the machine ca.: 0,060 t dimensions of the machine ca.: 0,4 x 0,4 m 15 pallets for Makino A 55, size 400 x 400 with T-slots for sale *

Condition: used, Year of construction: 2004, Technical details: table length: 920 mm table width: 600 mm ampere: 13,2 A weight of the machine ca.: 6 t dimensions of the machine ca.: 2,46 x 2,24 x 2,33 m Ledpfouzbayjx Acnern X-axis: 600 mm y-axis: 400 mm Z-axis: 260 mm max. table load: 1500 kg The dimensions for transport are: wide 2240 mm x high 2330 mm x deep 2460 mm weight approx. 6000 kg. *

Condition: excellent (used), Hexagonal tower Dimensions 500 x 500 x 500 mm Height 930 mm Base plate 630 x 630 mm Grid 40 mm Double angle bracket Dimensions 630 x 200 mm Height 760 mm Base plate 630 x 630 mm Grid 40 mm Ledjyl Swdjpfx Acnsrn Square tower Dimensions 400 x 400 mm Height 930 mm Base plate 630 x 630 mm Grid 40 mm

Condition: excellent (used), Base pallets for MAKINO A77/81 Dimensions: 630 x 630 mm with T-slots, slot spacing 125 mm Lrjdpfeyl Sv Tex Acnjn Several units available!

Condition: excellent (used), FANUC 16 MA-Pro 3 Control With B-axis Working travels 900 x 800 x 970 mm Tool changer with 244 Positions Spindle speeds 0-12'000 rpm Spindle taper HSK100 2 paletts 630 x 630 mm Ljdpfx Asylbc Nscnjrn B-axis 0.001° Cooling through spindle 3D measuring taper Tool breakage control device Chip conveyor Misc. accessories MARCELS MASCHINEN AG

Condition: used, Year of construction: 1998, x-travel 800 mm y-travel 750 mm z-travel 770 mm Control Fanuc type PRO-3 tool taper HSK 100 power capacity 30 kW turning speeds 10000 U/min rapid traverse 35 m/min Tool changer 90 Pos. Cooling through the spindle 70 bar size of pallet 630x630 mm Table load 1200 kg rotary table tiltable 1 Grad type of pallet-changer 2 weight of the machine ca. 15 t Special features: Tool magazine for 90 HSK-A100 short-taper tools 70 bar high-pressure coolant system Indexable rotary table swivels in 1° increments Pallet size 630 x 630 mm Maximum table load 1,200 kg Hydraulic power unit for fixture clamping system Fanuc Pro-3 control system Automation: Dual pallet changer Tool breakage detection Automatic workpiece measurement with Marposs touch probe The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. Lrjdoyqu Naepfx Acnen We look forward to your visit. Your Markus Hirsch Team