Used Marcelo Plank for sale (143)

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! Kodpfx Aoi Ri Rvob Tsln The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: ee3256d63dd23b3ad1bdf9ab0, empty load weight: 10,280 kg, maximum load weight: 13,720 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box on offset recessed in the floor with cover, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the low bed in the tramline area after the offset, sloping towards the entrance, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area 400 mm higher than wheel recess.2nd pair of wheel recesses between the axles in the drop center in the tramline area, slanted towards the entrance, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Wheel well cover can be pulled out from the main frame, with wooden inserts. Distance from main frame beam to beam outside approx. 1280 mm (wheel well area) Widenings extendable to 3,000 mm, foldable on the wheel recess extensions (widening not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed or under the cargo bed if technically possible Wooden planks 70 mm for widening to 3000 mm Kjdpfxsi Ri I Ns Ab Tsln Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 8 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 2 x at the front on the offset 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension with lift & lower valve can be operated separately at the front and rear Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Trailer Infocenter, for displaying vehicle data such as axle load (no calibrated scales) and odometer Axle load detection via EBS-Canbus signal, for display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Vehicle - driving stability system Duomatic connection at the front, with connecting cable to the truck, EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur even though the function is given) 2 white front position lights in LED 2 white/red rear lane departure ligh

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Kjdpsi Riy Esfx Ab Teln Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 408ba9a39bbb8087056d6e563, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) Kodpfx Abji Ri Dae Toln 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: new, machine/vehicle number: ede0610378cbe39cc4883251d, empty load weight: 24,000 kg, maximum load weight: 7,550 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction 1st pair of wheel recesses after steel platform recessed in the tramline area, inclined towards the entrance, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. If machines are to be driven where the overall height is to be checked, we request a technical data sheet for the machine types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer). Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 110 3 pairs of lashing points, 10 tons each, integrated in the floor at the front Incl. 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x to neck area remaining distributed in between Distance not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles which guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Twin steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides Kedpfx Asi Ri Ryob Toln 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, incl. Afterwards with 70 mm softwood floor, steel/checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. cannot be achieved. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Incl. with

Condition: new, machine/vehicle number: 15431365fe5515297a6a9fb05, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Kljdpfx Aji Ri A Sjb Tsn Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side Kodpfx Asi Ri Dljb Toln 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Kedpfx Absi Ri Dds Tjln Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 55d3c5c03e032385649769b1b, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box recessed in Incl. Turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points, 10 tons each, integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm towing eye Please note! With 40 mm drawbar eye, the maximum permissible total weight of the truck is 18000 kg, otherwise 50 mm drawbar eye required. Axles + suspension Ksdpfx Abji Ri I Ee Teln SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring jack support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany 1 with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame Ral 3002 carmine red 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: f8fb99947a1c19bc4d63549ff, empty load weight: 6 kg, maximum load weight: 17 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Kledpfxei Riwfe Ab Tjn Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 7 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion with M&S marking Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Coun

Condition: new, machine/vehicle number: f79a9f15e7131d57a512793ab, empty load weight: 8,900 kg, maximum load weight: 15,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Widenings extendable to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Kledoi Ri Izopfx Ab Tsn Parabolic suspension with maintenance-free steel-rubber bearings and mechanical incl. axle load compensation front and rear Axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front offset with steel/ checker plate covering Then with 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany With Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Incl. Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized

Condition: used, maximum load weight: 27,500 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 06/2023, next inspection (TÜV): 06/2025, loading space volume: 100 m³, Year of construction: 2023, Equipment: ABS, bioSTAR approx. 100 cbm, 14.9 m internal length silver grey BIOSTAR - STEERABLE AXLE - V14900 - VERTICAL FRONT WALL - VERTICAL REAR DOOR Internal body length: approx. 14,900 mm Internal body width: 2,475 mm Body volume: approx. 90 cbm Gross vehicle weight (GVW): 36 t Axle spacing: 1,310 mm Unladen weight: 8,500 kg Kodpfx Ajxplxzeb Tjln King pin height: 1,150 mm TECHNICAL DESCRIPTION 1. CHASSIS KING PIN HEIGHT: Precise king pin height is 1,150 mm. AXLES Tridem: Manufacturer: SAF - CUSTOM DESIGN (CD) Capacity: 3 x 9 t Suspension: Original SAF air suspension Brakes: Large disc Wheel offset: ET 120 Brake wear indicators (BVA) included The first axle is a self-lifting axle controlled via the EBS-E system. The third axle is a trailing steering axle. CONNECTIONS BRAKE WEAR INDICATOR (BVA): Brake wear indicators are connected. LIFT AXLE FUNCTION: Without lift axle. Including traction aid. TRACTION AID: The traction aid is activated by pressing a button in the truck (button in truck not included). AIR SUSPENSION: Lifting and lowering function. Aluminum air tanks. STEERABLE TRAILING AXLE LOCKING: Locking of the steerable trailing axle is managed as follows: - via reverse lights - by button in truck (button in truck not included) TYRES: 6 x 385/65 R 22.5 tyres for regional haulage (manufacturer's choice) on ALCOA MATT aluminum rims, ET 120. BRAKING SYSTEM - EBS: EBS-E system WABCO 2S/2M - PREMIUM MODULATOR Dual-line compressed air braking system in accordance with CE guidelines. Spring-loaded parking brake operating on 2 axles. With SMARTBOARD. R.S.S. (Roll Stability System) LIGHTING - ASPÖCK: 24 Volt electrical equipment. 2 x 7-pin + 1 x 15-pin ISO sockets. Aspöck kit. Orange LED lighting mounted on the trailer side. Without junction box at rear - NORDIC. REAR LIGHTING IN UNDER-RUN PROTECTION: Lighting is installed in the fixed aluminum underrun protection. With foldable aluminum lighting cover. 2 x 1 five-chamber lamp - EUROPOINT III - LED version. HYDRAULICS POSITION: Connection at the front wall. With additional connection option below the body in front of support legs. ACCESSORIES EXTENDIBLE LADDER AT REAR: Extendible ladder integrated at rear of vehicle, right side. PNEUMATIC CENTRAL LOCKING: With pneumatic central locking. TOOLBOX: PVC toolbox with key (800 x 460 x 430 mm) SPARE WHEEL HOLDER: Single aluminum spare wheel holder. 2. BODY FRONT WALL: The front wall is made of heavy-duty aluminum plank profiles. INTERNAL SEALING BETWEEN FLOOR AND FRONT WALL: Fixed sealing between floor and front wall using aluminum profile and PVC gasket. SIDE WALLS: Inner and outer surfaces smooth. Double-walled side wall profiles, 600 mm wide - 30 mm thick - 3 mm inside - 2 mm outside (grain specification). Side wall profiles are fully welded on the inside. WEAR PLATE: Aluminum wear plate, rectangular, inside rear, 2000 (L) x 1500 (H) x 4 mm. MOVING FLOOR SYSTEM: CARGO FLOOR CF 500 SL-C, electric control. 21-board floor system. Drive unit consists of 3 double-acting hydraulic cylinders with 200 mm stroke. Rear end plate in stainless steel. FLOOR SYSTEM OPERATION: Electric control with radio remote (genuine Cargo Floor). Loading - stop - unloading via switch. Manual emergency operation using unique red Cargo rotary knob. MOVING FLOOR FRAME: Frame for wheelbase 7,850 mm. 21 floor boards. FLOOR BOARDS: 21 aluminum floor boards - 8 mm ribbed, with welded aluminum end caps. REAR DOOR: 2 portal h

Condition: refurbished (used), Year of construction: 2003, functionality: fully functional, Four-sided planer/moulder with 6 spindles, fully refurbished in 2025 (zero operating hours post-refurbishment), manufacturer SCM, Superset model. This professional industrial equipment delivers high-precision solid wood processing, ideal for workshops or factories seeking superior performance and long-term reliability in solid wood machining. The machine represents a modern technological solution, originally manufactured in 2003 by renowned Italian producer SCM, and brought up to current standards through a thorough refurbishment—zero operating hours since overhaul. We guarantee quality and operational safety, comparable to a new machine. Ksdpfxsw Emlwo Ab Tjln Main technical specifications: Maximum working width: 240 mm (adjustable from 15 mm) Maximum working height: 160 mm (adjustable from 10 mm) 6 independent processing spindles, each with its own motor and electronic braking First lower horizontal spindle: 5.5 kW, Ø 40 mm, 8300 rpm Right vertical spindle: 5.5 kW, Ø 40 mm, length 170 mm, 8300 rpm Left vertical spindle: 5.5 kW, Ø 40 mm, length 170 mm, 8300 rpm Upper horizontal spindle: 11 kW, Ø 40 mm, length 170 mm, 8300 rpm Second upper horizontal spindle: 13.8 kW with inverter, Ø 40 mm, length 170 mm, 10,000 rpm Second lower horizontal spindle: 5.5 kW, Ø 40 mm, length 240 mm, 8300 rpm Feed System: Cardan shaft transmission, each unit equipped with its own feed roller and universal joint Feed motor: 4 kW with electronic brake Continuously variable feed speed with frequency inverter: 6–30 m/min Upgraded electric cabinet with advanced safety systems and improved ergonomics for easy operation and maintenance. Main advantages: High precision and versatility for ripping, planing, and profiling solid wood, regardless of complexity Reliability assured by complete refurbishment and premium-quality components Optimized cost compared to new equipment, with no compromise on performance Financing option: 5-year leasing for flexible investment management Recommended applications: Production of tongue and groove boards, solid wood flooring, beams, battens, planks, mouldings, and other solid wood products Ideal for carpentry workshops, joinery factories, manufacturers of doors, windows, furniture, industrial production of finished lumber

Condition: new, Year of construction: 2023, ACOUSTIC ROAD BARRIER PANEL PROFILE PRODUCTION LINE by Bosporas Machinery TURKIYE The line produces a perforated profile which are joined together to form Acoustic / Sound Insulation Panel used on roads, highways as a wall barrier. Consists of: DECOILER Motorized Hydraulic Expansion 6 Ton Capacity COIL CAR 6 Ton Capacity Ksdpfek Iy Hmox Ab Tjln SERVO FEEDER ENCODER FEEDER HIGH-SPEED H FRAME PRESS (160 stroke/min.) HIGH-SPEED PERFORATION PERFORATION TOOL LOOP AND SENSORS ROLL FORM TURK HEAD SHEAR MOTORIZED CONVEYOR AUTOMATED JOINING UNIT Material 0.8 mm CR Steel BOSPORAS Technologies Machinery provides a complete turnkey metal roll forming solution with high quality and competitive prices. The lines that we are experienced: GUARD RAIL PRODUCTION LINES C, U, Z AND SOLAR PANEL PROFILE PRODUCTION LINE LOGISTIC WAREHOUSE TRAVERSE PRODUCTION LINE CABLE TRAY PRODUCTION LINE MARKET SHELVING PRODUCTION LINE SUSPENDED METAL CEILING PRODUCTION LINE SOALR FRAMING AND RACKING PRODUCTION LIGHTING FIXTURE BODY AND LID PRODUCTION LINE PANEL RADIATOR TOP AND SIDE COVER PRODUCTION LINE METAL GRID AND PLANKS PRODUCTION LINE METAL DOOR AND DOOR FRAME PRODUCTION LINE PVC WINDOW GYPSUM BOARD PROFILE PRODUCTION LINE AGRICULTURE AND ANIMAL HUSBANDRY PRACTICES AGRICULTURAL VEHICLE APPLICATIONS PAINTING PLANT PANEL PRODUCTION LINE AUTOMOTIVE INDUSTRY APPLICATIONS COIL PUNCHING APPLICATION HOUSEHOLD APPLIANCES INDUSTRY APPLICATIONS and other customized roll-forming machinery.

Condition: used, maximum load weight: 42,400 kg, overall weight: 64,000 kg, axle configuration: > 3 axles, first registration: 01/2011, Equipment: ABS, Goldhofer STZ-VLS4-37/80 and Goldhofer Dolly SX 1-25/80 - Height-adjustable low bed with removable gooseneck ----* Manufacturer: Goldhofer * Type: STZ-VLS4-37/80 * First registered: 01/2011 * Color: yellow * Total weight: 64,000 kg * Empty weight according to vehicle registration document: 21,600 kg * Axles: 4x BPW axles, of which 1st axle is steered via turntable steering, the remaining 3x axles are hydromechanical forced steering * Steering knuckle axles up to max. 45 degrees * Tires: 235/75 R17.5 approx. 70% * Suspension: Air suspension with lifting and lowering * EBS Wabco * Removable gooseneck with aluminum side walls * Hydraulic cylinders for support on the tractor unit * Toolbox with flap at the front of the gooseneck * Controls and pressure gauge on the left of the gooseneck * Gooseneck designed for freely rotating 1-axle dollies * Low bed for the chassis can be raised and lowered hydraulically * Chassis with excavator trough (starts from the 2nd axle) * Extendable widening of the loading area 440mm (2x 220mm) and 700mm (2x 350mm) * Wooden planks to bridge the gap between the widenings * Air suspension with raising and lowering to min. 825mm to 1,025mm (no driving position) * 2x fixed driving heights: * 1st driving height 925mm +100mm/-100mm * 2nd driving height 885mm +100mm/-100mm * 2 pairs of retractable lashing eyes in the gooseneck floor * 5 pairs of retractable lashing eyes in the low bed floor * 5 pairs of side lashing eyes on the low bed chassis * 4 pairs of stake holes in the low bed floor * 3 pairs of retractable lashing eyes in the chassis floor * 2 pairs of side lashing eyes on the chassis chassis * 2 pairs of stake holes in the chassis floor * 2x lashing eyes in the excavator trough * Rear of the vehicle sloped 10 degrees * 1-part hydraulic ramps (2,850mm x 720mm) and hydraulic supports at the rear * Operation of hydraulic ramps + supports at the rear left * Smartboard at the rear right * Additional LED reversing lights on the gooseneck and at the rear of the low loader * 1st hand German vehicle!! German papers!! 1st hand!! Goldhofer SX 1-25/80 Dolly ----* Manufacturer: Goldhofer * Type: SX 1-25/80 * First registered: 03/2011 * Color: Yellow * Total weight: 28,000 kg * Empty weight according to vehicle registration document: 2,750 kg * Axles: 1x BPW axle * Tires: 235/75 R17.5 approx. 70% / twin tires * 3" fifth wheel plate * Single fender Kljdpfx Abjx Suzao Ton * Supports * Loading manometer * 1st hand German vehicle!! German papers!!

Condition: used, mileage: 1,200 km, power: 110 kW (149.56 HP), first registration: 05/2025, fuel type: diesel, overall weight: 3,500 kg, next inspection (TÜV): 05/2027, color: white, gearing type: mechanical, emission class: euro6, number of seats: 2, total length: 6,250 mm, total width: 2,000 mm, total height: 3,150 mm, Year of construction: 2025, Equipment: ABS, air conditioning, central locking, crane, electronic stability program (ESP), soot filter, tail-lift, 0567. GW25N336771, Furniture lift Böcker Agilo 27/1-6 LH, guide rail package, auxiliary drive, furniture slider, telescopic headrest wheels, Maxi furniture platform, enclosed loading area, electric controls, additional installation of extendable front supports, facade protection plank, hydraulic latch lock, reversing camera, turn assist, active brake assist, reinforced front axle, radio, air conditioning, lane departure warning, intelligent speed assistant, toolbox. Subject to errors and prior sale. Ksdpfxoxtvzzs Ab Tjln

Condition: used, mileage: 150 km, power: 129 kW (175.39 HP), first registration: 02/2026, fuel type: diesel, overall weight: 7,200 kg, color: white, gearing type: mechanical, emission class: euro6, number of seats: 3, loading space length: 4,800 mm, loading space width: 2,200 mm, loading space height: 2,400 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, parking heater, soot filter, tail-lift, Are you looking for a different model, engine variant, size, or other features? Feel free to contact us. We offer financing and leasing at attractive terms – also available for the Netherlands, Austria, and start-ups! ----Vehicle: * Wheelbase: 4,100 mm * 6-speed manual gearbox * Single cab * Twin rear wheels * Gross vehicle weight: 7.2 tonnes * Digital tachograph * Speed limiter: 90 km/h Interior: * Passenger bench seat with multifunction storage * Overhead storage compartment above the windshield * Luxury driver's seat, sprung, heated * Grab handle on A-pillar * Comfort headrests * Leather multifunction steering wheel * Cloth seat covers Safety & Assistance: * Electronic Stability Program (ESP) * AEBS System + City Brake * Driver airbag * Front monitoring system (MOIS) * Oper. & maint. manual electronic * Rear parking sensors * Lane Centering Plus (LC) * Eco-Smart function * Additional speed limiter * Seatbelt warning signal F/B * Driver Drowsiness Alert (DDAW) * Turn assist, passenger side (BSIS) * Rear blind spot radar * Traffic sign recognition incl. (ISA) * Spare wheel with rear frame mounting Wheels & Technology: * Electrically adjustable and heated mirrors * Digital radio DAB 7" touch display * Apple CarPlay/Android Auto * All-weather tires * AIRPRO air suspension on rear axle * Manual central handbrake * Air conditioning with automatic climate control * Heated fuel filter * Auxiliary hot water heater * Light and rain sensor * Fog lights Kodsv R Rfmjpfx Ab Tsln * Full LED headlights * 4G connectivity box incl. TCO * Adaptive cruise control (ACC) * Pre-wiring for toll system (OBU) * Central locking with remote control * AdBlue tank 20 L and driver heater * Integrated 90 L fuel tank * Battery 12V 110 Ah Sliding Curtain: * Steel frame * Antislip plywood flooring * Side aluminium drop-in planks * Sliding curtains both sides (color: black, other colors on request) * Upper guide rail for sliding curtain * Lower securing straps for sliding curtain * Roof spoiler * Tailgate * Reversing camera * Side underrun protection * Mudguards with splash flaps * Side marker lights Tail Lift: * Dhollandia * Load capacity: 1,500 kg * Platform depth: 1,800 mm * Roll-off protection * LED warning lights * Remote control with spiral cable * Towbar up to 3.5t trailer payload (ball hitch, 13-pin 12V trailer socket) Additional bodywork extras available for a surcharge. ----Notice: Please call before your visit – we want to ensure your required vehicle is available on site. If the vehicle is not in Wachtendonk, we are happy to deliver from our stock. Custom builds available on request. Your vehicle partner since 1996. Call or email now – we look forward to hearing from you! No liability for typographical or printing errors. Subject to prior sale and changes.

Condition: new, maximum load weight: 29,560 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 10,600 mm, loading space width: 2,480 mm, loading space height: 2,300 mm, loading space volume: 60 m³, Equipment: ABS, Stock no. 5640 Purchase, lease, or lease with a purchase option by arrangement! Approximately 60m³ STAS agricultural moving floor trailer with integrated grain hopper / service door, etc. ---- * Manufacturer: STAS * Model: FARMSTAR - Agricultural Moving Floor * First Registration: - (New vehicle) * Colour: Chassis RAL 9005, Superstructure RAL 7001, Tarp SIO 7500 * Volume: approx. 60m³ (10.60m long x 2.48m wide x 2.30m high) * Axles: 3x SAF axles / 1st axle with lift and traction assistance / disc brakes * Tyres: 385/65 R22.5 with Speedline Diamond aluminium rims * Wheelbase: 6.25m * Suspension: Air suspension with raise/lower functionality * Gross Weight: 36,000 kg * Unladen weight (manufacturer): 6,440 kg * Payload: 29,560 kg * ABS / EBS Ksdpfx Aexl Ntueb Tsln * CARGO FLOOR CF 500 SL-C with radio remote control and control panel rear left * 21-plank floor system, 6mm ribbed * Aluminium end caps, welded * Rear closure plate made of aluminium * Integrated grain hopper * Additional guides under the floor profiles * Residue emptying wall with brushes and stainless steel handles * Bulkhead made from aluminium plank profiles * Service door in the bulkhead * Smooth side walls inside and outside (grain specification), fully welded * Inspection window in the left rear side wall * Swing doors (50/50 split) * 4x locking rods * Swivelling crossbar at door closure * Hydraulic connections at the front with 3m hoses and * Connection option below the superstructure (without hoses) * Pressure 1" female * Return 1" female * Operator platform with access front left and right * Fifth wheel height 1,150mm * Individual mudguards * Full load supports * Rolling tarp (900g/m²) with quick-clamp system * Aluminium roof bows, foldable * Foldable rear aluminium light guard * Aluminium air tanks * 1x toolbox front left * 1x toolbox rear right * Shovel & broom holder left * 1x 2x8-step aluminium access ladder fixed right * 1x extendable ladder at the rear right * Smartboard * TPMS tyre pressure monitoring * LED rear lights – 5-chamber * 2x LED work lights in front of the axles * 2x LED reversing lights at the rear * 1x LED work light inside the bulkhead * 2 x 3-function lamps at the top of the door crossbar Purchase, lease, or lease with a purchase option by arrangement! Notice regarding possible errors in the advertisement: Despite careful preparation of this listing, occasional errors may occur in the text or information provided. We assume no liability for mistakes, changes, or prior sale. All information is subject to change and not guaranteed. Please contact us to verify details or if you have any questions.

Condition: new, Year of construction: 2024, sheet thickness steel (max.): 4 mm, working width: 600 mm, coil weight: 6,000 kg, Rollforming Line for production of * Guard Rails, Highway Road Barrier, Crash Barrier Profiles RAY-A, C, RAY-B, OMEGA, SIGMA, 3M, 3 WAVE * Solar profiles C and U. Automatic width adjusted line for thicknesses between 1 - 4 mm. * Cable Tray and Ladder Profiles also other standard and customized profiles .. Consists of: DECOILER Motorized Hydraulic Expansion 6 Ton Capacity COIL CAR 6 Ton Capacity SERVO FEEDER ENCODER FEEDER HIGH-SPEED H FRAME PRESS (160 stroke/min.) HIGH-SPEED PERFORATION PERFORATION TOOL LOOP AND SENSORS ROLL FORM TURK HEAD SHEAR MOTORIZED CONVEYOR Kodpfx Ajtq R Uyeb Tjln AUTOMATED JOINING UNIT Material 0.8 mm CR Steel. BOSPORAS Technologies Machinery provides a complete turnkey metal roll forming solution with high quality and competitive prices. The lines that we are experienced: GUARD RAIL PRODUCTION LINES C, U, Z AND SOLAR PANEL PROFILE PRODUCTION LINE LOGISTIC WAREHOUSE TRAVERSE PRODUCTION LINE CABLE TRAY PRODUCTION LINE MARKET SHELVING PRODUCTION LINE SUSPENDED METAL CEILING PRODUCTION LINE SOLAR FRAMING AND RACKING PRODUCTION LIGHTING FIXTURE BODY AND LID PRODUCTION LINE PANEL RADIATOR TOP AND SIDE COVER PRODUCTION LINE METAL GRID AND PLANKS PRODUCTION LINE METAL DOOR AND DOOR FRAME PRODUCTION LINE PVC WINDOW GYPSUM BOARD PROFILE PRODUCTION LINE AGRICULTURE AND ANIMAL HUSBANDRY PRACTICES AGRICULTURAL VEHICLE APPLICATIONS PAINTING PLANT PANEL PRODUCTION LINE AUTOMOTIVE INDUSTRY APPLICATIONS COIL PUNCHING APPLICATION HOUSEHOLD APPLIANCES INDUSTRY APPLICATIONS and other customized roll-forming machinery.

Condition: good (used), Year of construction: 2003, functionality: fully functional, Length of sliding table: 3,000 mm Cutting width at rip fence: 1,000 mm Cutting height with blade diameter 450 mm: 75 - 150 mm Cutting height with blade diameter 350 mm: max. 100 mm (each at 90-degree blade position) Double carriage on steel round guides, no Pertinax Reinforced main saw motor: 7.5 kW Maximum saw blade diameter: 450 mm Height adjustment of the saw unit via dimension input on the control panel Motorized tilt adjustment of the saw unit via dimension input on the control panel Supplied with newly installed 350 mm saw blade 2-axis scoring saw unit, can be set in the control system to desired height and alignment relative to the main saw blade Kjdpfx Ajx Dax Ejb Teln Scoring unit automatically lowers below table level when not in use Adjustment of the scorer can be done while the machine is running RAPIDO scoring saw blade – simplifies scoring width adjustment, set up in max. 3 minutes Adjustment range: 2.8 – 3.8 mm Additional accessories: - Mitre fence extendable to 3,200 mm, with 2 foldable stops - LASER cutting line indicator, e.g. for trimming cuts on solid wood planks

Condition: new, Year of construction: 2025, functionality: fully functional, Technical Data: Cutting height: 200 mm Cutting height at 45° incline: 140 mm Tiltable to the left up to 67° Tiltable to the right up to 45° 5 kW hydraulic feed brake (optional) Kodpfxon R A Ewe Ab Teln Cutting length: 420 mm at 90° position Cutting length at 45° swivel: 295 mm Tilt angle: left 60°, right 30° Tilt adjustment from the front via hand crank. 1 wood saw blade, diameter 520 mm 1 heavy-duty cross-cut roller conveyor, length 6,000 mm, mounted on the left. The stop is adjusted from the front via handwheel. Length is digitally readable to the millimeter. The stop is pneumatically locked. 1 digital readout (230 V version) 1 heavy-duty feed roller conveyor, right side, length 4,000 mm Machine length: 11,700 mm Fully mobile Machine packed on wooden planks Images show a customer’s machine. Available upon request also with 215 mm or 240 mm cutting height.

Year of construction: 2011, condition: excellent (used), TIMA VOLLALU universal transporter with tilting loading area Type: GTAHK 360/188/3.5 Internal dimensions: 3500x1880x300mm Total weight: 3500kg Payload: 2800kg Own weight: 700kg Ksdpfx Abohwmr He Toln Tyres: 155/70 R12C Year of construction: 2011 Certificate valid until 07/2022 VOLLALU - trailer with tipping loading area Frame welded in hollow profile construction Aluminum plank floor Double-acting hydraulic cylinder for tilting function spare wheel mounted 8 pcs. lashing eyes

Condition: used, maximum load weight: 23,000 kg, overall weight: 29,500 kg, axle configuration: 2 axles, first registration: 06/2013, Year of construction: 2013, Equipment: ABS, ORTHAUS JXL010 JUMBO Special Curtainsider/Tautliner High Volume with 107 m3 ----VEHICLE EQUIPMENT * ORTHAUS JUMBO JXL010 TAUTLINER * CUBIC CAPACITY: 107 m3 * FIFTH WHEEL HEIGHT: 940 - 1,020 mm * SAF AXLES * GALVANIZED FRAME * TYRE SIZE: 245/70 R 17.5 * WABCO BRAKING SYSTEM * GOOD TIRES * EXPORT SALES ONLY WITH DEPOSIT MIN. €500 - €2,000 ---- Technical Specification: Axles: SAF axles with drum brakes, first axle liftable. Coupling Height: 940 - 1,020 mm GALVANIZED FRAME Tyres: 9 units of 245/70 R 17.5 tires on steel rims. Brake System: WABCO 2S/2M EBS system including ABS and Roll Stability Program function. Landing Leg: Jost-brand landing legs. Lighting Kit: Aspöck 24 Volt Kledpfx Absw E Av Ee Ten Floor: 30 mm resin-coated plywood planks. Suitable for forklift loads up to 7,000 kg. Lashing: Lashing rings with 2 ton capacity, 13 lashing rings on each side. ---- Changes, errors, and prior sale reserved! Further vehicles can be found on our homepage. Sale is exclusively subject to our General Terms and Conditions (GTC) – see homepage. Important Notice: Despite carefully checking all details in our offer, mistakes can occur. Some errors may be caused by data transmission across various platform providers. Therefore, we emphasize that all information is provided without guarantee and does not represent a legal claim. Legal Notice: This sales advertisement does not constitute an offer in the sense of §145 BGB. Rather, it is information for initiating a contract. The details given here are non-binding and do not constitute guaranteed properties.

Condition: used, maximum load weight: 26,827 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 04/2025, next inspection (TÜV): 04/2026, loading space length: 16,240 mm, total width: 2,550 mm, Year of construction: 2025, Equipment: ABS, Kässbohrer KSLA RJ Mega Jumbo Low Loader with Wheel Wells and Excavator Boom Recess Hardly Used Immediately Available Including Winch TECHNICAL SPECIFICATIONS: * Fifth wheel height (H5): approx. 950 mm * Rear swinging door: 2,300 mm * Overall length (L): 13,190 mm * Gooseneck length (Gl): 3,950 mm * Platform length (Pl): 9,240 mm * Extension (Pe): 3,500 mm * Locking position: 500 mm * Platform height (Ph): 770 mm * Wheelbase (Wb): 7,800 mm * Axle spacing (A): 2,260 mm * Axle load: 24,000 kg * Axles: 12 tons technical load capacity (10 tons permissible load capacity) BPW * Axles with drum brakes * Axle load: 8 tons load capacity * King pin capacity: approx. 15,000 kg * Unladen weight ±3%: 12,173 kg * Overall width (W): 2,550 mm + 600 mm (with extendable sides) * Sliding platform: Not included * Total weight (at 80 km/h): 39,000 kg * Total weight (at 60 km/h): 42,900 kg RUNNING GEAR: * Number of axles: 3 * Steering type: 2 x rigid axles at the front, 1 x trailing axle at the rear Klodpfx Aexy Ddksb Ton * Lift axle: Overload-dependent manual axle lift system on the 1st axle * Lift axle control: Manual * Wabco braking system * Tyres: 12 x 205/65 R17.5 * 1 x spare wheel holder on front bulkhead * Air suspension, 1 x load gauge indicating pressure at the axle assembly * NATO socket CHASSIS: * S700 MC * Gooseneck with 90° vertical corners * 45 mm hardwood floor and steel floor with embossed pattern above the wheel wells only * Galvanized extensions 8 x 2 for enlarging the platform width up to 300 mm * Jost landing gear, 50 tons * Foldable rear supports, 45 tons * 2 pairs of wheel wells for transporting wheeled vehicles * Wheel well bridge for covering the wells RAMPS: * Ramp loading capacity: approx. 40 tons * Suitable for hydraulic folding and adjustment * Wooden floor, 40 mm thick, 3,070 mm long, 850 mm wide, 3,715 mm high (closed), ramp angle 14°, capacity 40 tons * Rear ramp safety: Ramp protection chain included LOAD SECURING: * Lashing rings: 2 x 2 x 5,000 daN capacity, 1 x 2 x 10,000 daN capacity rings on gooseneck; 3 x 2 x 5,000 daN, 4 x 2 x 10,000 daN rings on the outer platform; 2 x 2 rings with 8,000 daN capacity under the outer frame; 4 x 2 rings with 6,000 daN capacity at the tray area included * Stake pockets: 5 x 2 stake pockets (52 x 102 mm) * 6 x container lock housings and 4 x twistlock container locks for transporting 1 x 20FT or 1 x 30FT containers * Gooseneck panels: 1 x steel front plate (450 mm x 2,550 mm), 2 x aluminum side panels (360 mm x 1,500 mm), 1 x aluminum rear panel (360 mm x 2,550 mm) * Plug-in stakes: 8 x 2 units, 50 mm x 100 mm ACCESSORIES: * 1 x PVC-coated steel toolbox (single lid) 750 x 400 x 360 mm (H x D x W) * 1 x rotating beacon * 1 x work light on underrun guard * Oversize boards with LED lighting 2 x 2 units, 423 mm x 423 mm * Storage box on gooseneck (600 mm x 830 mm x 2,310 mm) * Timber planks for oversize transport * Chassis color: RAL 3020 Traffic Red For further information, please do not hesitate to contact us.

Condition: new, overall weight: 80,000 kg, axle configuration: > 3 axles, Equipment: ABS, More vehicles available – excerpt from the equipment specification. Full specification upon request. Kjdpsxarmaofx Ab Tsln GOOSENECK Gooseneck in SNT design to optimize cargo bed length, approx. 3,700 mm long, rear with a beveled section approx. 1,000 mm x 10°. For tractor units: 4x2, 6x2, and 6x4. - Plug-in steel front wall, approx. 400 mm high - ASPÖCK-UNIBOX mounted at the front control panel with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic unit for controlling hydraulic functions, except hydraulic winches - Outer beams of the gooseneck with mounting holes for boltable lashing rings. First hole approx. 200 mm from front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) - On the gooseneck: 1 pair of plug-in side ALU drop-sides, approx. 400 mm high, anodized finish - On the gooseneck: 1 plug-in rear ALU drop-side, approx. 400 mm high, anodized finish - Approx. 40 mm hardwood flooring on the gooseneck, over the kingpin chequer plate - 3.5-inch kingpin - Gooseneck guide plate for saddle plate, approx. 500 mm wide - Round NATO socket on the front connector panel (Maeler & Kaege VG 96 917) - 2 pairs of lashing rings with retaining spring, suspended from outer beams of the gooseneck (LC 5,000 daN) CARGO BED Extendable cargo bed, length approx. 8,800 mm with rear bevel approx. 500 mm x 10°. Pneumatic locking with conical locking pin and reinforced positions; supply lines are protected inside the extendable beams and automatically adjust to cargo bed length. - BPW axles and suspension: first axle self-steering, all others hydro-mechanical forced steering. First axle with electro-magnetic reverse lock, activated via reverse gear or manually. Technical axle load: 12,000 kg each. Air suspension with lift/lower valve. - 235/75 R 17.5 3PMSF twin tires – brand at our discretion - Mechanical landing gear with 2-speed gearbox and crank. JOST Module B – static test load = 50,000 kg - Cargo bed with continuous and between-axle interrupted approx. 50 mm hardwood floor (increases friction coefficient) - Elongated holes for hanging and movable bridging elements: - At front of cargo bed - 1 movable intermediate platform, approx. 300 mm wide, for extension tube with large cross-section, with chequer plate - Front and rear with elongated holes for hanging/movable bridging elements - 1 pair of lashing rings on front cross-member (LC 10,000 daN) - 7 pairs of recessed lashing rings in the outer frame, foldable to the outside (LC 10,000 daN) - Extendable (galvanized) bed wideners approx. 230 mm per side (without wood planks) - 1 pair of mechanical rear stabilizers - Steering from front and rear adjustable via remote cable control, with single-axle steering alignment, no installation in tractor unit - TPMS tire pressure monitoring sensors installed on all wheels - Bed locking with conically welded lock profiles every 500 mm - Lock monitoring left and right on the trailer - For the intermediate platform, approx. 300 mm wide: mechanical lock to secure the platform on the extension - 5 pairs of threaded blocks on the extendable beam for mounting boltable M20 rings (LC 5,000 daN) BRAKE SYSTEM Brake system