Used Sack Press for sale (12,075)

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm Nkodpfx Agodzqlte Iju waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Double-column hydraulic press SCHÖN Type SH 25 Machine no.: 4453 Year of manufacture: 1999 Pressing force: 25 tons Column width: 500 mm Lateral column clearance: 120 mm Table surface: 440 x 320 mm Table opening: Ø 175 mm Ram surface: 360 x 220 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 100 mm Max. installation height: 270 mm Table height above floor: 900 mm Motor power: 7.5 kW Connection voltage: 380 V, 50 Hz Equipment: - Safety light curtain SICK, type FGS 300-11 - Two-hand operation - Stroke counter - Rapid and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Pressing force regulation - Adjustable pressing time 1–10 s (pressure holding time) - Adjustable return stroke speed Nkodpjw A Amrefx Ag Ieu - Blow-off device electrically pre-wired, without air valve - Manual hydraulic tool safety, adjustable via handwheel Dimensions (L x W x H): 1300 x 1200 x 2200 mm Weight: approx. 1200 kg Good condition

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter Nkjdpfx Asu Rwa Ieg Ieu - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, 12-piece die block for GEWA press brake Nodpfxswbvmij Ag Ijku Bending tool for press brake, lower tool Type: 0255/14 V-block size: 16 mm for 90° V-block angle: 88° Die depth: approx. 8 mm Height: 120 mm Max. pressure per meter: 100 t/m Die base width: 60 mm Total length: 4175 mm Segment lengths: 4 x 835 mm, 1 x 400 mm, 1 x 200 mm, 1 x 100 mm, 1 x 50 mm, 1 x 40 mm, 1 x 20 mm, 1 x 15 mm, 1 x 10 mm Weight: 110 kg Very good condition

Condition: used, Single-column Eccentric Press MÜLLER GEFREES Type 60 SV DK (Identical to ExP60) Very lightly used eccentric press in original condition Machine No. 5250686 Year of manufacture: 1986 Nearly new condition Nodpfx Agsi A A Tbe Isku Press force: 60 tons Throat depth: 280 mm Table surface: 740 x 560 mm Ram surface: 385 x 200 mm Through-hole in table: 300 x 200 mm Table surface (intermediate plate): 740 x 560 mm Through-hole in intermediate plate: Ø 103 mm Intermediate plate thickness: 70 mm Clamping pin bore: 40 mm Table height above floor: 815 mm (with intermediate plate) Installation height, max.: 275 mm (with intermediate plate) Installation height, max.: 345 mm (without intermediate plate) Stroke adjustment: 10–90 mm Ram adjustment: 60 mm Strokes per minute: 100 Motor power: 3 kW Drive: 380 Volt, 50 Hz - Mechanical rotary wedge clutch with pneumatic actuation - Spring-loaded single-jaw brake, controlled by cam disc - Stroke release via pneumatic footswitch - Overload protection with breaking plate in the ram - Table height adjustment via 2 threaded spindles - Manual central lubrication system by BEKA Schmiertechnik - Operating manual and pneumatic diagram included Space requirement (L x W x H): 1400 x 1100 x 2200 mm Weight: 3.4 tons In very good, almost new condition

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Pressure capacity 40 ton. throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm ram surface 250 x 200 mm Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Njdpfxstx E Rqj Ag Isku Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: used, Pneumatic press, compressed air press BOSCH type Manufacturer no.: Year of manufacture: 1980 Pressing force: 18 kN = 1.8 t at 5 bar 15 kN = 1.5 t at 4 bar 12 kN = 1.2 t at 3 bar 8 kN = 0.8 t at 2 bar 6 kN = 0.6 t at 1.8 bar Throat depth: 100 mm Ram stroke: 70 mm Table size: 245 x 200 mm Ram face: Ø 45 mm Max. installation height: 235 mm Clamping pin bore: Ø 20 mm with clamping screw Compressed air requirement: 5 bar - Pressing force infinitely adjustable via pressure regulator - Pneumatic cylinder with ram adjustable in height by 90 mm - Pneumatic dual-hand control - Mounted on a metal frame with wooden boards Required floor space (L x W x H): 1050 x 700 x 1600 mm Weight of pneumatic press: 82 kg Nkjdpfx Agjh U Dtue Ieu Weight including table frame: 140 kg In very good condition

Condition: used, Single column hydraulic press DUNKES type HZT 2,5 Machine No. H94-2558 Year of construction 1994 pressure force 2,5 ton. throat 180 mm table area 420 x 300 mm drop-through opening in table 60 x 185 mm ram surface Ø 40 mm clamping spigot bore Ø 20 mm ram stroke 160 mm Installation height max. 250 mm Rapid traverse downward 65 mm/sec. Rapid traverse upwards 160 mm/sec. Working speed 8,3 mm/sec. Table height above floor 950 mm Hydraulic operating pressure 135 bar Tank capacity hydraulics approx. 100 liters Drive power 1,5 kW Mains connection 400 Volt, 50 Hz - Installation height can be increased by shortening the piston rod by 80 mm - Pressure and travel cut-off - 2-hand operation at the machine - stroke counter - safe press control with 2 monitored hydraulic valves Nsdpfxoh Uhqyj Ag Ieku - UVV 11.064 VGB 7.n.5.2 (for manual insertion work) - 32047 read off operating hours - Electrical circuit diagram and hydraulic diagram available space requirement L x W x H 1100 x 980 x 1950 mm weight 700 kg very good condition

Condition: used, Single column eccentric press MÜLLER GEFREES type PDET 5 S/EK Machine No. Year of construction 1988 pressure force 5 ton. throat 125 mm head clearance 170 mm table area 280 x 220 mm waste hole Ø 90mm ram surface 160 x 100 mm stroke adjustment 4 to 40 mm ram adjustment 30 mm Installation height largest stroke top max. 210 mm Stroke rate 200 strokes/min. Clamping spigot bore Ø 25 mm Table height above floor 900 mm motor power 0,55 kW mains connection 380 volt, 50 Hz - pneumatic clutch-brake combination - electric foot switch - switch cabinet at the machine space requirement L x W x H 900 x 600 x 1700 mm Nsdsik Srwjpfx Ag Ieku weight 530 kg very good condition

Condition: used, Single-column hydraulic press HYDRAP type HPSK 25 No. 6312 Year of construction 1989 Pressure force 25 ton. Ram stroke 500 mm throat depth 300 mm Installation height 700 mm Table surface 1000 x 500 mm Table bore Ø 210 mm Plunger surface 400 x 360 mm Clamping pin bore Ø 40 mm Table height above floor 855 mm Feed speed in rapid traverse 280 mm/sec. Pressing speed 3.5 mm/sec. to 25 mm/sec. Return speed 280 mm/sec. Hydraulic tank capacity 240 liters Drive power 7.5 kW Mains connection 400 Volt, 50 Hz. - Operation and programming via SIEMENS S5 with OP1 control system Nksdehrakvepfx Ag Ieu - Measuring system for stroke adjustment - Pressing speed infinitely variable via potentiometer - Pressure setting infinitely adjustable manually via pressure regulator - Short stroke device - Mechanical tool clamping on ram with T-slots and clamping pin hole - Switch cabinet with electrical control on the machine - Two-hand operation and electrical connection for foot control - Control provided for electrical mold monitoring - Hydraulic diagram and electrical diagram available Space requirement L x W x H 1800 x 1200 x 2930 mm Weight approx. 4 tons good condition

Condition: used, Single-column toggle press MAY - MAYPRES - KOMATSU Type MKN 1-63/6 Eccentric toggle press, eccentric press Year of manufacture approx. 1984 Pressing force 60 tons Thrust 160 mm Table size 580 x 360 mm Ram surface Ø 270 mm Clamping pin bore Ø 40 mm Distance between columns 218 mm Ram stroke 60 mm Ejector stroke 15 mm Ram adjustment travel 30 mm Max. installation height 300 mm (with intermediate table plate) Stroke rate 70 strokes per minute Motor speed 1400 rpm Motor power 3 kW Power supply 380 V, 50 Hz - Pneumatic clutch and mechanical brake with pneumatic release (separate clutch-brake combination) - Table intermediate plate L x W x H 580 x 360 x 58 mm, with holes and cutouts - Mechanical ejector, ejector device in the machine table, Ø 80 mm Nksdpfx Ajv Uraajg Iju - Electric two-hand control and foot switch - Movable safety screen, UNIDOR protective housing with pneumatic front screen - BALLUFF cam switch Space requirement L x W x H 1400 x 1200 x 1850 mm Weight 3 tons Good condition

Condition: used, Single column eccentric press PELS - RICHTER type PEKR 125 Machine. No. 20684 Year of construction 1967 pressure force 125 ton. throat 430 mm table size 1100 x 750 mm ram area 890 x 650 mm table opening Ø 400 mm stroke adjustment 6 to 115 mm ram adjustment 100 mm installation height largest stroke top max. 450 mm Clamping spigot bore Ø 50 mm Stroke rate 60 strokes/min. Table height above floor 900 mm motor power 7,5 kW Mains connection 380 Volt, 50 Hz - Overload protection by crushing plate in ram - Compressed air clutch-brake combination DESCH Nkjdpfx Agofim The Ieu - ram weight balancing cylinder - manual ram adjustment - two-hand operation - cam gear - Grease central lubrication Vögele - stroke counter Space requirement L x W x H 2300 x 1450 x 3030 mm weight approx. 10 ton. good condition

Condition: used, Single-column eccentric press WEINGARTEN type ER 63 Machine. No. 52A / 63 Year of construction 1963 Pressure capacity 63 ton. throat 280 mm Table surface 630 x 530 mm ram stroke adjustable 8-100 mm Nkodpfjlb I Dzox Ag Isu ram adjustment 63 mm Stroke rate 65 strokes / min. Motor power 4 kW Mains connection 380 Volt, 50 Hz - Clutch/brake combination with WEINGARTEN friction threaded clutch - Electric lift release via foot switch - Wheel reduction gear - Overload protection by breaker plate - Front crankshaft support bearing Space requirement L x W x H 1500 x 1100 x 2500 mm Weight 4.5 tons good condition

Condition: used, Single column eccentric press WEINGARTEN type ERV 40 Machine No. 537 / 65 Year of construction 1965 Compressive force 40 ton. throat 230 mm table size 570 x 470 mm ram surface 250 x 200 mm clamping spigot bore Ø 40 mm installation height max. approx. 520 mm stroke adjustment 8 - 88 mm slide adjustment travel 63 mm Stroke rate 70 strokes per minute Drive power 3 kW Nodpfoffm Hhox Ag Ieku Mains connection 380 Volt, 50 Hz - Table height adjustment - Overload protection by crushing plate - clutch-brake combination by WEINGARTEN friction thread clutch - electric 2-hand operation and foot switch - central lubrication via hand pump space requirement L x W x H 1600 x 1150 x 2300 mm weight approx. 2,6 ton.

Condition: used, Clinching unit TOX - Pneumatic-Hydro Toxpress Hydro-pneumatic press TOX Pressotechnik KRAFT PAKET Type CRS 03.62 No.: 207599.2 Year of construction approx. 2005 Pressure capacity: max. 80 kN = 8 tons Projection: 20 mm Installation height: 32 mm - Built-in clinching tool - Pneumatic valve for control - Push-through joining or clinching Nkedpsdz Sqqjfx Ag Iju - For creating a form-fit connection between 2 sheets without piercing or heating the sheets - Mounted on the stand - with simple electrical control and foot switch Own weight: 230 kg Comes from a production plant, sold without electrical control

Condition: used, Single-column hydraulic press SCHÖN type FES / C 7 Machine no. No. 4281 Year of construction 1995 Pressure force 7 ton. throat 170 mm Projection round cycle station 60 mm Table size 310 x 200 mm Rotary indexing table Ø 400 mm, with 12 indexing stations Plunger surface approx. Ø 100 mm Plunger plate 315 x 200 x 35 mm Ram stroke 100 mm Installation height rotary table - ram plate max. 130 mm Nkedpfx Asr I E Itjg Iju Table height above floor 890 mm Ram speed rapid traverse downwards approx. 300 mm/sec. Ram speed rapid traverse upwards approx. 300 mm/sec. Ram speed Working speed approx. 30 mm/sec. Drive power 1.5 kW Mains connection 380 Volt, 50 Hz Tank capacity approx. 50 liters hydraulic oil - Rotary indexing control via SIEMENS S7- 1200 - GECHTER pneumatic rotary indexing table with 12 indexing stations - Mechanically adjustable fixed stop - Adjustable pressure holding time in the UT - electrical 2- manual operation Space requirement L x W x H 1450 x 850 x 1900 mm weight 700 kg good condition

Condition: used, Single-column hydraulic press MAE type S63SZ SO . 551277 Year of manufacture approx. 1977 Nominal pressing force: 63 tons Pressing force: 50 tons (practically tested) Throat depth: 320 mm Table area: 850 x 630 mm Ram area: 1050 x 500 mm Ram stroke: 500 mm Max. installation height: approx. 730 mm Table height above floor: 970 mm Hydraulic tank capacity: 600 liters Drive power: 15 kW Power supply: 380 Volt, 50 Hz - Hydraulic draw cushion below the table with bores through the tabletop Njdodzp Tropfx Ag Ioku - Two-hand operation - Electrical control cabinet damaged Required space (L x W x H): 2000 x 1200 x 3420 mm Weight approx. 5 tons The machine is operational, the control cabinet is mechanically damaged. During test run, the machine achieves a pressing force of 50 tons, presumably a pressure relief valve is venting.

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet - 2-hand control panel adjacent - ground level installation - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. Njdpfxodzp Tcs Ag Isku The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: used, length: 2750width: 1100heigth: 2050weight approx.: 3500pressure: 50bending length: 2550 CNC Bending Press 3 Axes Y1, Y2, and Z Hydraulic Tool Clamping for the Upper Tool Darley System Technical Details: Machine Type: EHP 50.25/20 Max. Pressing Force: 500 kN Bending Length: 2550 mm Downward Speed: 100 mm/s Max. Pressing Speed: 13.5 mm/s Return Speed: 75 mm/s Stroke Length: 120 mm Cylinders: 2 pcs Motor Power: 5.5 kW Nodpfxewiatpj Ag Ioku Oil Tank: 100 Liters

Condition: used, pressing force: 150 t, Eccentric Press Brand: ULECIA Serial No.: 1877 Njdpfxjylzcvj Ag Ioku Type: Pneumatic Clutch Force: 150 t Strokes per minute: 40 Stroke (Max / Min): 160 / 24 mm Power: 10 HP *The press is delivered as is, without any type of warranty.

Condition: ready for operation (used), Year of construction: 2016, pressure 20.0 t chamfer lenght 850 mm distance between columns 850 mm back stop - adjustable 375 + 400 mm stroke of upper beam 196 mm dayligth 470 mm ajustment speed 200 mm/sec table height ca. 900 mm total power requirement 5.0 kW weight of the machine ca. 2500 kg New price ~ 85.000 euros well-kept / very good condition (!!) with electromechanical direct drive (servo motor + ball screws) Machine is operated without hydraulic oil - in checked condition - machine video - ?v=foxzKIA7vX8 Nsdpfx Agsxacifs Ijku Description : High performance, fast travel speeds and the best ergonomics this bending machine to a perfect tool in terms of productivity and Accuracy. This allows an unrivaled high productivity in the field of small and middle bending parts can be achieved, since even complicated bending sequences several stations can be processed very quickly. A large number of different and universally divided tools are possible an almost unlimited variety of areas of application. Furnishing : - Stable machine frame for standing and seated operation - Deformation-optimized press beam - Highly dynamic, electromechanical. Direct drive (servo motor + ball screws) - CNC control Panasonic Toughbook incl. USB and WIFI connection - CNC controlled axes : Y + X + R + Z1 + Z2 - CNC control unit in front right, swivelling - Inductive length measuring system with temperature compensation - Ergonomic machine design - AMADA system upper tool holder - AMADA system lower tool holder - 1x brand new universal tool set (complete) - front safety device (DUAL Laser/Iris Rapid Bend) - Rear security cover - Laterally pivoting protective doors - 2x foot switch, for standing and sitting operation - Support tables comfort (front) - User manual (original) * Special accessories included: - 4-axis backgauge (axes X+R+Z1+Z2) * Speed X axis .. 250 mm/sec * Speed R axis .. 600 mm/sec * Z axis speed .. 1100 mm/sec * Positioning accuracy X axis .. 0.04 mm * Positioning accuracy R axis .. 0.06 mm * Travel X axis .. 375 + 400 mm * Travel R axis .. 180.0 mm

Condition: ready for operation (used), pressure 30.0 t punching cross-cut in cmm 30.0 in 9.0 mm stroke ca. 35 Hub/min Nodpfx Ajxaaipsg Ijku throat 610 mm stroke - stepless adjustable 0 - 28.0 mm oil volume 35.0 l work height max. 1010 mm total power requirement 4.0 kW weight of the machine ca. 1200 kg. range L-W-H 1400 x 700 x 1600 mm good condition (!!) with a lot of application tools (stamps/dies) Furnishing: - electro-hydraulic hole punch, with large throat - Material/sheet metal scrapers including scraper plates - Large material support table, with adjustable depth stops - continuous stroke adjustment - freely movable foot switch including protective cover - Forklift pockets for easy transport - side storage area - lots of accessories + tools - including tool cabinet - Matrix base (for special size matrices) - Stamp holders (for special size stamps) - original user manuel

Condition: used, Year of construction: 2005, Pressure 800 t distance between columns 2560 mm stroke 1050 mm Distance table/ram, stroke up 1870 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 300 t Die cushion stroke in table 395 mm Die cushion area in table 2300 x 1300 mm Ram surface 2500 x 1730 mm Die cushion pressure in ram 63 t Die cushion stroke in ram 150 mm Side window 1000 mm Nkedpfx Agjvuuikj Iou Oil volume 4300 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 10,0 m Height above floor 7,0 m year of manufacture 1974 overhaul 2005: formerly type BZE 800, converted to ZE 800 by manufacturer with new ram and new cylinder mit ölhydraulischem Antrieb, hydraulischem gesteuertem Ziehkissen im Tisch und Stößel stored in dismantled condition - Video at seller’s site before dismantling available

Condition: used, Year of construction: 1979, pressure 1000 t distance between columns 3030 mm stroke 350 mm Distance table/ram, max. stroke up, adjustment up 1400 mm table surface area 3000 x 2000 mm table height over floor 430 mm side window 1450 x 1400 mm ram surface 3000 x 2000 mm speed down 300 mm/s speed up 340 mm/s working speed 18 - 44 mm/s return capacity 120 t oil volume 4400 l width with platform 4950 mm power capacity 2 x 90,0 + 10,0 kW weight 87,0 t Dimensions (WxDxH) 4,35 x 3,65 x 7,55 m height over floor 6,05 m height beneath floor 1,5 m SPECIAL DEAL Nkedjvuk I Aopfx Ag Iou as is where is WITHOUT putting into operation / WITHOUT additional work stored in partly dismantled condition free loaded to truck

Condition: good (used), Karl Krause Large Bookbinding Press with Tapping Block The machine is fully operational and ready for operation. Manufactured by Karl Krause, Germany. The press has a tapping block that increases the pressing force. Pressure: 5 tons Plate dimensions: 550 x 490 mm Njdpfeynfydjx Ag Ijku