Used Scm Fs 520 Class for sale (605)

Condition: new, - NEW-descriptionCutting plane directly on the saw bladeHeavy steel and cast iron constructionPrecision-guided format sliding carriage made of aluminium,anodized as standardLarge-area table extension guided on a telescopic arm andlongitudinally adjustableExtendable aluminum telescopic fence, angle adjustable with professionalstop flapsRip fence with quick release and fine adjustmentLarge work table made of milled gray cast iron stays permanently flatThe standard table extension and table extension enable easy work with larger workpiecesQuiet running and precise cutsEquipped with a powerful three-phase motorThe large dimensioned cast iron sawing unit is attached twice to the cast iron table and guarantees stability, precision, smooth running and a long service lifeMaximum cutting height is also achieved with the built-in scoring deviceEquipment details:Double cradle saw unitGenerously dimensioned, made of steel/cast ironClose to the saw blade, supported on both sides for precision, smooth running and a long service lifeAdjustable in height and up to 45° with a crankMaximum cutting height is also achieved with the built-in scoring deviceAlso available with scoring unittelescopic stopExtendable telescopic stop up to max. 2550 mmAngle adjustableWith professional stop flapsAluminum sliding carriageWith a thousand times proven ball contact systemInsensitive to dust and dirt due to minimal contact point between ball and trapezoidal rail10-year Holzkraft guarantee on wear and tear on the guidewaysRip fence with round rod guideWith fine adjustment and quick releaseStable round rod guide made of ground steel with a diameter of 45 mmCan be folded down as standard for cutting large workpiecesTechnical specifications:Dimensions and weightsWeight (net) approx. 380 kgConnection suctionSuction connection diameter 120 mmSuction connection diameter saw blade protection 60 mmMachine body length 1388 mmWorking area length 1000 mmMachine body width/depth 689 mmWorking area width/depth 2000 mmSpace required length 5118 mmSpace requirement width/depth 3830 mmelectrical dataConnection voltage 400 VDrive motor power 5.0 kWPhase(s) 3 PhNominal operating mode drive motor S6Type of current ACDuty cycle drive motor 40%Mains frequency 50 HzSliding carriage and tableFormat slide length 2250 mmTable length 840 mmFormat sliding carriage width 270 mmTable width 560 mmFormat sliding carriage height 124 mmTable height 900 mmcircular saw unitCutting width with rip fence 900 mmMax. cutting height 90° 90 mmMax. cutting width to the left of the saw blade 2310 mmMax. cutting height 45° 63 mmtrimming length 2250 mmSaw blade diameter 315 mmSaw blade inclination 90 - 45°Saw blade speed 4000 rpmArt. No. 5504323Ausziehbarer Teleskop-fence to max. 2550 mmWinkeladjustableMit Profi-AnschlagklappenAluminium-sliding tableMit tausendfach bewährtem KugelkontaktsystemStaub- and schmutzunempfindlich durch minimalen Berührungspunkt zwischen Kugel and Trapezschiene10 Jahright hand Holzkraft-guarantee on abrasion der Führungsbahnenrip fence with round rod guidingMit fine adjustment and quick clampingStabile round rod guiding aus geschliffenem steel with 45 mm diameterSerienmäßig tiltable for den Zuschnitt großer WerkstückeTechnische Daten:dimensions and Gewichteweight (Netto) ca.   380 kgAnschluss Absaugungsuction nozzle diameter   120 mmsuction nozzle diameter Sägeblattschutz   60 mmAufstellinformationenTransportbreite   900 mmErläuterung required spaceDie d... Iodjvyuqfjpfx Abvjth

Condition: used, machine/vehicle number: 008238, X axis working area: 3660 mm Isdpjx A E Tfefx Abvjth Y axis working area: 1550 mm Working Table: Flat table Main Electrospindle power: 12 KW Number of controlled axes: 3 axes Total number of drilling spindles: 12 Total number of tool changer positions: 15

Condition: used, machine/vehicle number: 008132, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt Premilling Unit: yes Corner Rounding Unit: yes Max feed speed: 18 m/min Itodpew Idc Rsfx Abvoh Maximum panel thickness: 60 mm Operating Units: 7 nr

Condition: used, machine/vehicle number: 008108, Max width workable: 1050 mm Ijdpfew Idduex Abveth Max length workable: 2400 mm Max height workable: 250 mm

Condition: used, Year of construction: 2008, 3650 x 1560mm Matrix Table 4455mm x axis stroke [for routing] 1930mm y axis stroke [for routing] 250mm z axis stroke 150mm Max panel clearance X / Y Axes vectorial speeds 43m/min Z axis speed 15m/min Power 2000 Routing Unit 9 / 10hp for HSK63F toolholders. Speeds from 12000 to 18000rpm 250m3 / hr vacuum pump Telesolve long distance remote diagnostic system Fitted with following options Interpolating Z axis Centralised dust extraction system Pre-setting for angle driven heads TR10 Fixed 10 position toolchanger [ mounted on side of table ] R8 Rapid 8 position rotary toolchanger [ mounted on operating unit support beam ] 2 x Electronic detecting systems for panel height and tool length Itodpozd Utwsfx Abvoh 3 x Additional rear stops Automatic centralised lubrication "PC Office" Console for easy movement around machine. Including Windows XP operating system 15" Colour monitor Keyboard CD Rom drive 40 Gbyte hard disk 128MB Ram Serial nr - AA2 / 000268? Year - 2008 CE Compliant Condition - Good

Condition: used, Year of construction: 2016, operating hours: 8,893 h, total height: 2,350 mm, total length: 4,300 mm, total width: 1,880 mm, Colour: Grey Empty weight: 1.310 kg - Year: 2016 - Documentation available: Yes - └ Type Documentation: Technical data, Operating system, User manual, Electrical diagrams - └ Language: NL - └ Type: Hardcopy - CE marking present: Yes - CE certificate present: No - Serial number: AB/226310 - Operating hours: 8893 - Main motor power [kW]: 5.5 - Number of controlled axes [pcs]: 1 - Working range X [mm]: 3050 - Working range Y [mm]: 900 - Working range Z [mm]: 60 - Number of milling spindles [pcs]: 1 - Tool holder interface: ISO30 - Max. spindle speed [rpm]: 18000 - Horizontal drilling unit: Yes - Horizontal drilling spindles [pcs]: 6 - Max. drilling depth [mm]: 35 - Vertical drilling unit: Yes - Vertical drilling spindles [pcs]: 12 - Max. drilling depth [mm]: 60 - Manual operation: Yes - Control: SCM Xilog Isdpfx Abjxy Rk Revsth - Software: Xilog Plus - Saw unit present: Yes - Safety feature: - Spindle speed control: Continuously adjustable - Transport dimensions: 4300mm x 1880mm x 2350mm (l x w x h) - Transport weight [kg]: 1310kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: ready for operation (used), Year of construction: 2006, machine/vehicle number: AA1/015406, functionality: fully functional, operating hours: 14,808 h, working width: 1,300 mm, spindle speed (max.): 24,000 rpm, working height: 200 mm, working length: 3,110 mm, No minimum price – guaranteed sale to the highest bidder! The machine is still in operation and can be inspected while powered on. TECHNICAL DETAILS Working area X-axis: 3,110 mm Working area Y-axis: 1,300 mm Working area Z-axis: 200 mm Maximum travel X-axis: 3,500 mm Maximum travel Y-axis: 1,815 mm Maximum travel Z-axis: 440 mm Table length: 3,050 mm Table width: 13 mm Number of milling spindles: 1 Spindle speed: 600 - 24,000 rpm Number of controlled axes: 5 Horizontal drilling spindles: 6 Vertical drilling spindles: 12 Tool changer positions: 16 MACHINE DETAILS Main motor power: 11 kW Main motor power of the vacuum pump: 5.5 kW Capacity of the vacuum pump: 250 m³/h Iedjzdy E Sjpfx Abvsth Dimensions & Weight Dimensions (L x W x H): 9,000 x 2,450 x 2,850 mm Installed dimensions (L x W x H): 4,600 x 6,500 x 3,400 mm Shipping dimensions: 9,000 x 2,450 x 2,850 mm Empty weight: 4,000 kg Shipping packages: 1 unit Operating hours: 14,808 h EQUIPMENT Milling table: Beam table Tool clamping system: HSK-F63 Material clamping system: Pneumatic Drilling tool Saw unit System/Software: Xilog plus Safety feature: Safety mat Vacuum pump: Becker CNC options: Chip conveyor, Hand control CNC documentation: User key/licenses

Condition: excellent (used), Catalog number: 6368 TECHNICAL DATA - Max width of the workpiece: 230mm - Max height of the workpiece: 130mm 7 spindles: 1) Horizontal, lower: 230mm, 5.5kW 2) Vertical, right: 130mm, 5.5kW 3) Vertical, left: 130mm, 5.5kW 4) Horizontal, upper: 230mm, 7.5kW 5) Horizontal, upper: 230mm, 11kW 6) Horizontal, lower: 230mm, 18.5kW 7) Universal: 230mm, adjustable at 360 degrees, 5.5kW - All spindles adjustable up/down, left/right - All spindles equipped with an electric brake - Spindle diameter: 40mm - Spindles 4 and 5 adjustable electrically up/down - Top: 8 metal, torsion-type, infeed rollers, including 2 double rollers - Top: 4 rubber, outfeed rollers - Top: 2 pressure rollers - Bottom: Latches - Bottom, side: 3 pressure rollers - Bottom: 2 metal, smooth, infeed rollers - Bottom: 2 double, rubber, infeed rollers - Rollers pneumatically pressed - Feed via Cardan shafts - Stepless feed speed adjustment: 5-36m/min - Feed motor: 4kW - Electric adjustment of planing thickness: 0.75kW - Length of infeed table: 1980mm - Enclosed in a cabinet - Central lubrication of the table - Dust extraction nozzle diameters: 5x120mm, 2x150mm - Dimensions (L/W/H): 5500x1840x1900mm - Weight: approx. 5000kg ADVANTAGES – Made in Italy – With 7 heads – For wet and dry wood Ijdpfxjy N Agxo Abvsth – Last spindle is universal – Unpainted – Used planer, very good condition Net price: 136900 PLN Net price: 32600 EUR, depending on the exchange rate of 4.2 EUR (Prices may vary depending on higher fluctuations)

Condition: used, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, cutting height (max.): 120 mm, cutting width (max.): 300 mm, saw blade diameter: 350 mm, height adjustment type: mechanical, saw blade bore: 70 mm, actuation type: electric, - Operating manual, DTR - Italian production TECHNICAL SPECIFICATIONS: - Track width: 300 mm - Cutting height: 120 mm - Max. blade diameter: 350 mm - Motor power: 30 kW - Table width: 750 mm Itodpfxeym Ag Ss Abvoh - Min. workpiece length: 600 mm - Feed speed adjustable via gearmotor - Three rows of anti-kickback pawls - Possibility to mount a board – shoe - Spindle diameter: 50 mm - Sleeve diameter: 70 mm - Sleeve equipped with spacers - Automatic central lubrication - Four upper feed rollers - Extraction port diameter: 200 mm - Machine dimensions (L/W/H): 155 / 165 / 160 cm - Weight: 1800 kg

Condition: excellent (used), CATALOG NUMBER 7901 Technical specifications: - track width: 300mm - working width of roller: 300mm - max saw blade diameter: 350mm - saw blade bore diameter: 70mm - max cutting height: 120mm - table width with extension: 750mm Itjdpfxey S Aakj Abvjh - table length: 1530mm - from above: - kickback prevention barriers (safety barrier against material reverse) - metal sliding roller - kickback prevention barriers - metal sliding roller - shaft with saw blades - 2 smooth metal sliding rollers - from below: - guide rail - kickback prevention barriers - track - central track lubrication - stepless feed speed adjustment - feed motor: 1.5kW - main motor: 22kW - brake - suction nozzle diameter: 200mm - overall dimensions (L/W/H): 2300x1370x1570mm - weight approx.: 1700kg ADVANTAGES – Italian manufacturing – very good condition – technical DTR documentation – used multi-blade saw Net price: 32,900 PLN Net price: 7,830 EUR (calculated at 4.2 PLN/EUR) (Prices may change with significant exchange rate fluctuations)

Condition: used, Year of construction: 2016, MORBIDELLI AUTHOR M400 MAIN FEATURES 5-AXIS MACHINING UNIT "PRISMA: QUALITY AND PRODUCTIVITY AT THE HIGHEST LEVEL XILOG MAESTRO SOFTWARE: EXTREMELY SIMPLE MATIC PROGRAMMING" WORKTABLE: ONE POSITIONING FOR MULTIPLE MACHINING OPERATIONS TECHNICAL DATA AUTHOR M400 AXES Working area X-axis (inside stop) mm 3,680 Working area Y-axis (max. loadable piece on rear stops) mm 1,680 Workpiece passage Z / number of Z axes mm 170 / 1 Workpiece length with pendulum machining mm 1,650 Travel speed X-Y axes Pro-Speed m/min 85 Z-axis speed m/min 30 INSTALLATION Installed power KVA 62÷82 Compressed air requirement NL/min 400 Extraction air requirement m³/h 4,430 Extraction air speed m/s 25 Extraction nozzle diameter mm 250 GENERAL CHARACTERISTICS CNC-controlled drilling and milling center in gantry design and work table with workpiece supports, for carrying out: - vertical drilling on the panel surface - horizontal drilling on all four sides of the workpiece - groove milling with disc milling cutters - general milling work 3-4-5 axes MACHINE STRUCTURE The basic structure is a monolithic construction made of thick-walled steel. It is stiffened by welded reinforcements across the entire machine bed, making it extremely stable. The table shape used, with a large base, is the secret to ensuring lasting precision and stability. The machine layout allows the user optimal workflow with a minimum of space requirements. The mobile gantry support is made of a solid monoblock. It is positioned in the X direction on prismatic ground guides via recirculating ball slides. On this mobile unit carrier, the work unit is mounted on prismatic, ground guides and recirculating ball slides. All axes are moved on large-section prism linear guides and recirculating ball bearings with a large contact surface, ensuring optimal gliding even at the highest speeds and accelerations. Precise and rapid positioning of the movable gantry (X-axis) is achieved by a pinion and rack with helical teeth. Large-section recirculating ball screws ensure precise positioning of the work unit along the movable gantry (Y and Z axes). MOTORS, DRIVES AND INVERTERS Perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors, designed to achieve speeds of up to 90 m/min while ensuring the best finishing quality. CONTROL The control unit consists of a numerical control for milling and drilling machines with "Xilog Maestro" graphical user interface based on the Windows 7 Office operating system. 17-inch LCD color screen. QWERTY keyboard. Tilting control panel. Machine interface with Xilog Maestro software. Xilog Maestro Features Programming Parametric graphic programming Import of DXF files (2D; SPLINE, POLYLINE 3D geometries), linear or circular interpolation in three axes, linear in space, spiral in the selected plane. Programming with graphic and syntax aids for drilling and milling operations Automatic optimization of drilling operations and tool change cycles Possibility of Plate zero point shift for drilling on inclined or curved plate sides Iodpfxoy Dta Ss Abvjth

Condition: used, Year of construction: 2007, Working area: 2780 x 1140 mm (vertical milling) 2500 x 950 mm (horizontal drilling) X-Y travel: 2980 x 1271 mm Z-axis travel: 200 mm Passage height: 180 mm The structure of the base body is a monolithic construction made of thick-walled steel. It is stiffened by welded triangular plates across the entire machine bed, making it extremely stable. The triangular shape used for load-bearing parts, with a large base, is the secret to ensuring lasting precision and stability. The machine layout allows the user optimal workflow despite minimal space requirements. The base body constructed in this way therefore offers the machining unit a balanced and secure base with particularly good load distribution. The mobile unit carrier is made of a solid monoblock. It is positioned in the X direction on prismatically ground guides via recirculating ball slides. On this mobile unit carrier, the working unit is mounted on prismatic, ground guides and the recirculating ball slide. Description of the units and accessories (basic) Drilling unit: Drilling head with 10 + 4 spindles · 6 individually accessible vertical spindles in X · 4 individually accessible vertical spindles in Y · 2 horizontal spindles in X (1 + 1) · 2 horizontal spindles in Y (1 + 1) · Speed: 4,000 rpm · Power: 2.2 kW · Grid: 32 mm · Drill chuck: M 10 with 11 mm fitting · Extraction nozzle: D = 160 mm Vertical milling unit (position 2) · Tool chuck HSK 63F · Speed 1,500 - 24,000 rpm continuously adjustable via inverter · Motor power 4.4 kW (6 HP) from 12,000 rpm (S1) · Right-hand / left-hand rotation · Ceramic bearings · Scope of delivery: 4 tool chucks (right) without collet chuck · Tool changer · Side-mounted tool magazine 7-way (TR7) with full encapsulation to prevent chipping · 7 tool positions for HSK 63F tool holder arranged in a row · maximum tool diameter D=120 mm · maximum weight per holder 4.5 kg · maximum tool weight of all tools 20 kg (TR7) · angular gears can be accommodated Horizontal milling unit (position 1) Horizontal unit with two opposite outputs for milling and grooving. · Speed 9,000 - 18,000 rpm continuously variable via inverter · 1 output for collet 3-20 mm (ER 32) · 1 output for saw/collet 3-12 mm (ER20) (For saw D = 120 mm / bore 50 mm) · Motor power 3 kW (4 HP) · Max. tool diameter front milling: 20 mm · Max. tool length front milling: 110 mm · Max. tool diameter rear milling: 12 mm · Max. tool length rear milling: 80 mm · Max. saw blade diameter: 100 mm · Bore saw blade (ER 32): 50 mm · Mandrel diameter saw blade (ER 20): 12 mm Work table The work table is designed to guarantee the operator maximum freedom of movement. The vacuum quick clamping system ensures maximum flexibility with precise positioning and optimal grip of the workpieces. · 4 supports 900 mm continuously adjustable in X · 8 vacuum suction cups round D = 110 mm continuously adjustable in Y (2 per support) · 2 stops in X (1 x left / 1 x right) · 1 stop in Y per support (total 6) · The retractable reference stops are controlled via CNC. · Scope of delivery: 4 plug-on adapters for suction cups · Pendulum machining standard (2 working areas) Axis movement The drive system in X, Y and Z is carried out via ground ball screws of the highest precision class. The ball drive screw of the X-axis is located exactly in the center Itsdox Twdyjpfx Abveh

Condition: used, Year of construction: 2023, Exhibition machine Garbsen HORIZONTAL PANEL SAW GABBIANI P Manufacturer: SCM Type: GABBIANI P80 Year of manufacture: 2023 1 unit MAIN FEATURES INDIVIDUALLY SELECTABLE AIR CUSHION TABLES: AN INDISPENSABLE TOOL SIDE SAFETY DEVICES: MORE SPACE FOR WORKING FLOATING GRIPPERS: GUARANTEED PERFECT CUT TECHNICAL DATA GENERAL INFORMATION gabbiani p80 Saw blade projection mm 80 Working table height mm 950 Standard number of grippers 5 Number of grippers for versions 33/38/43 9 / 10 / 10 Number of grippers for versions 33/38/43 with FlexCut 1 unit (single gripper with double fingers included) 10 / 11 / 11 CUTTING DIMENSIONS Version 33 mm 3300x2100 Version 33 (Opt.) mm 3300x3200 Version 38 mm 3800x3200 Version 38 (Opt.) mm 3800x3800 Version 43 mm 4300x3200 Version 43 (Opt.) mm 4300x4300 AXIS SPEED Variable saw carriage speed m/min 6 – 60 Variable pusher speed () m/min 60 MAIN SAW BLADE Motor power (S6 -40%) - 50hz (star-delta start) kW (HP) 7 (9) (11) Speed – 50 hz rpm 4650 Saw blade diameter mm 340 Shaft diameter main saw blade mm 80 SCORING BLADE Motor power (S6 -40%) - 50hz kW (HP) 1.5 (2) Speed – 50 hz rpm 5850 Scoring blade diameter mm 200 Shaft diameter scoring blade mm 80 INSTALLATION Installed power kW 12÷15 Base machine voltage Euro voltage (400 V / 50 hz) Compressed air demand NL/min 300 Required compressed air pressure bar 7 Extraction air requirement m3/h 2440 Extraction air speed m/sec 20 Extraction port diameter mm 4x120 () Note: in countries where EU standards apply, the forward pusher feed speed is limited to 25 m/min. GENERAL CHARACTERISTICS Fully automatic, PC/PLC-controlled horizontal panel saw suitable for cutting solid wood, MDF, chipboard, plywood, and similar materials. Frame and working table – Machine frame is a steel tube construction – Working table of rib-reinforced steel with Bakelite coating – Longitudinal fence on the left side Saw carriage made of steel, consisting of: – a motor for the main saw blade and a motor for the scoring blade – vertical lifting of the saw blade on linear ball bearing guides and shoes – running rollers of hardened and ground steel – balanced mass distribution for optimal cut quality – running direction towards the longitudinal fence – saw carriage drive via rack and pinion – carriage travel on cylinder guides – cylinder guides of hardened and ground steel (5-year warranty), protected by special dust wipers – pneumatic switch for fast and safe main and scoring blade change Pressure beam – pressure beam with uniform pressure across the entire cut length, recesses to prevent collision with grippers; pneumatic height adjustment via high-precision rack and pinion, pressure adjustable from 1.5 to 6 bar – dual extraction system with one unit above the pressure beam for cleaning the work table and one unit below on the saw carriage – side automatic aligner with pneumatic cylinder over the entire length. Sliding on linear ball bearing guides and shoes. * Travel distance: 1200 mm * minimum working width: 60 mm * maximum working width: 1200 mm Positioning pusher and rear part of the machine – Positioning pusher full length, powered by a robust drive shaft. Positioning pusher control... Itedpfox Twcvex Abvsh

Condition: used, Year of construction: 2006, · Working area: 2,650 x 1,240 mm · X-Y travel: 2,995 x 1,385 mm · Z-axis travel length: 200 mm · Clearance height: 180 mm C-axis deactivated – 3-axis machine The base structure is a monolithic construction made of thick-walled steel. It is reinforced throughout the entire machine bed with welded-in triangular plates, which makes it extremely stable. The use of the triangle shape with a broad base for load-bearing parts is the key to lasting precision and stability. The machine layout allows the operator an optimal workflow despite minimal space requirements. The resulting base frame thus provides the machining unit with a balanced and secure foundation, ensuring excellent load distribution. The mobile unit carrier is built as a solid monoblock. It is positioned in X-direction on ground prismatic guides with recirculating ball carriages. The working unit is again mounted on ground prismatic guides and a recirculating ball carriage on this mobile unit carrier. Description of aggregates and accessories (basic equipment) Drilling unit: Drill head with 12 + 6 spindles · 7 individually selectable vertical spindles in X · 5 individually selectable vertical spindles in Y · 4 horizontal spindles in X (2+2) · 2 horizontal spindles in Y (1+1) · Speed: 4,000 rpm · Power: 2.2 kW · Grid: 32 mm · Drill interface: M 10 with 11 mm fitting Grooving saw unit in X: · Integrated in drill head · Grooving saw blade with max. diameter 120 mm Main milling unit (Position 2): · Tool holder HSK 63F · Speed: 1,500 - 24,000 rpm stepless via inverter · Motor power 4.4 kW (6 HP) from 12,000 rpm (S1) · Motor power 6.6 kW (9 HP) from 12,000 rpm (S6) · Clockwise/counterclockwise rotation · Ceramic bearings · Includes: 4 pcs. tool holders (right) without collet Tool changer R8L: Automatic tool changer for 8 tools. Mounted on the rear unit carrier for quick tool access. · Number of tool stations: 8 Isdpfex Twccex Abvsth · Max. tool diameter: 120 mm · Max. weight per tool: 4.5 kg · Max. total weight all tools: 22 kg · Holder for 1 angle gear · Moves in X direction Horizontal milling unit (Position 1): Horizontal unit with two opposing outputs for milling and grooving. · Speed: 9,000 – 18,000 rpm stepless via inverter · 1 output for collet 3-20 mm (ER 32) · 1 output for saw/collet 3-12 mm (ER20) (for saw D=120 mm / bore 50 mm) · Motor power: 3 kW (4 HP) · Max. front milling tool diameter: 20 mm · Max. front milling tool length: 110 mm · Max. rear milling tool diameter: 12 mm · Max. rear milling tool length: 80 mm · Max. saw blade diameter: 100 mm · Saw blade bore (ER 32): 50 mm · Saw blade arbor diameter (ER 20): 12 mm Work table: The work table is designed to guarantee the operator maximum freedom of movement. The quick vacuum clamping system provides maximum flexibility for precise positioning and optimal holding of workpieces. · 6 supports, 1000 mm, steplessly adjustable pneumatically in X direction · 12 round vacuum cups D = 110 mm, steplessly adjustable in Y (2 pcs. per support) · 2 stops in X (1 left / 1 right) · 1 stop in Y per support (6 in total) · Retractable reference stops are CNC controlled · Pendulum machining standard (2 work zones) --- other clamping systems available as options --- Axis movement: The drive system in X, Y and Z is via ground recirculating ball screws...

Condition: good (used), Code: 0414 Brand: SCM MINIMAX Model: ME 25 - CE Standard Automatic edge bander for joinery, furniture, custom-made furniture, panels, doors, kitchens and various – CE Standard – Year 2017 Technical data: Thickness of roll edge 0,4–3 mm Max edge thickness 5 mm Min/max panel height 12/50 mm Panel feed speed 7 mt/min Work surface height 904 mm Min panel length/width 190/65 mm High-grip toothed feed belt Panel support roller conveyor along the entire length of the machine Iodpfxozfapme Abvjth Composition: Gluing unit: Glue tank capacity 1 kg – Motor power 0,18 Kw End cutting unit: Motor power 0,37 Kw – End trimming blade diameter 90 mm Z 20 – Blade rotation speed 12000 rpm Overlapping trimming unit: Upper and lower motor power 0,75 Kw – Vidia cuttersn diameter 75 mm Z 4 – Cutter rotation speed 12000 rpm Edge scraper unit for finishing Pvc/Abs edges Glue scraper unit for removing any excess glue Suction inlet diameter 120 mm Overall dimensions mm 1950 x 700 x 1250 h Weight kg 430

Condition: used, Year of construction: 1990, Working width: 630 mm Planing height: 250 mm Planer shaft: Tersa Number of knives: 4 Height adjustment: electric Planing thickness display: mechanical counter Feed speed: stepless, approx. 6–18 m/min Infeed roller: steel Outfeed rollers: 2 x steel Iedpfx Aoyxganjbvsth Table rollers: yes, powered Motor power: 5.5 kW Extraction connection: 160 mm Machine length: 1200 mm Machine width: 1200 mm Weight: 1100 kg

Condition: used, Year of construction: 1993, Working width: 410 mm Jointer cutterhead: Tersa Number of knives: 3 Jointer bed length: 2000 mm Concave/convex fence adjustment: no Adjustable angle of the jointer fence: yes Itjdpfx Ajzdzakebvoh Raising the jointer bed: manual Maximum feed thickness, thickness planer: 240 mm Height adjustment of the thickness table: electric Indication of planing thickness: mechanical counter display Feed rate: 6/12 m/min Infeed roller: steel Outfeed roller: steel Pressure bar: continuous Table rollers: no Motor power: 5 kW Motor brake: yes, automatic Dust extraction port: 160 mm Machine length: 2300 mm Machine width: 1100 mm Weight: 450

Condition: excellent (used), CATALOGUE NUMBER 8021 Isdpfx Ajzdfnyebvoth TECHNICAL DATA - max. width of the workpiece: 1100 mm - max. height of the workpiece: 150 mm 2 units: 1) grooved rubber roller for calibrating 2) grooved rubber roller - motor power: 11 kW - brake - from above: - split, sliding metal roller - pressure roller - unit - pressure roller - unit - pressure roller - cleaning brush - from below: - 2 sliding metal rollers - conveyor belt - 2 sliding metal rollers (outlet) - new conveyor belt - pneumatic belt oscillation - electric table lifting - stepless feed speed adjustment - feed motor: 1.5 kW - grinding thickness potentiometer - working pressure: 8-10 bar - dust extraction nozzle diameter: 3x165 mm, 1x140 mm - overall dimensions (L/W/H): 1870x1850x2210 mm - weight: 2165 kg ADVANTAGES - Made in Italy, SCM brand - New conveyor belt - 2 units - Grinding thickness potentiometer - Unpainted - Used sanding machine, very good condition Net price: 26900 PLN Net price: 6405 EUR, depending on the exchange rate of 4.20 EUR (Prices may vary due to higher fluctuations)

Condition: used, Year of construction: 2014, total height: 2,800 mm, total length: 10,300 mm, total width: 2,450 mm, Colour: Grey Empty weight: 6.600 kg Price: On request - Year: 2014 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: AA2/002546 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - - Max. spindle speed [rpm]: 24000 - - Main motor power [kW]: 11 - Type milling table: Beam table - Tool clamping system: HSK-F63 - Material clamp system: Pneumatic - Drilling unit present: Yes - └ Motor power [kW]: 3 Iedpfx Aoytcl Iebvoth - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 10 - Tool changer positions [pcs.]: 24 - System/software: Xilog plus - Safety feature: Safety light curtain, Door interlock switches, Enclosed fence - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - └ Type: Vtlf 250 - └ Year of manufacture: 2008 - └ Main motor power [kW]: 5.5 - └ Connection diameter [mm]: 70 - └ Oil free: Yes - Tools included: Yes - CNC options: Offcut conveyor, Manual control - CNC documentation available: USB stick - Table length [mm]: 5200 - Table width [mm]: 1300 - Voltage [V]: 400 - Current consumption [A]: 64 - Transport dimensions: 10300mm x 2450mm x 2800mm (l x w x h) - Transport weight [kg]: 6600kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2012, operating hours: 9,974 h, total height: 2,700 mm, total length: 7,700 mm, total width: 2,420 mm, Empty weight: 7.390 kg CNC machining centre SCM Morbidelli M-600 5-axis machine Year of construction 2012 Machine no. AA2/002032 Working distance X-axis 5020 mm Working distance Y-axis 1680 mm Working distance Z-axis 250 mm Tool positions 36 Vertical drilling spindles 24  Software SCM XILOG MAESTRO SCM PRISMA K SCM TTS system Milling spindle liquid-cooled SCM TecPad MORBIDELLI TV Matic SCM PRO-SPACE SCM RAPID 12 SCM RAPID 24 Including vacuum pump Capacity 250 m3/h Disassembled for transport Weight 7450kg - Details: - └ Description: Machine gives malfunction spindle - Year: 2012 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: AA2/002032 - Operating hours: 9974 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - Type milling table: Beam table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 24 - Saw unit present: Yes - Tool changer positions [pcs.]: 36 - System/software: SCM Maestro - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - └ Capacity [m³/h]: 250 - CNC options: Offcut conveyor Itjdownhccepfx Abvoh - Working range X [mm]: 5020 - Working range Y [mm]: 1680 - Z-axis working range [mm]: 250 - Transport dimensions: 7700mm x 2420mm x 2700mm (l x w x h) - Transport weight [kg]: 7390kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Colour: Grey Wide belt sander SCM Sandya 10S M2 110 Built in 1999 Sanding belt dimensions 2620x1115mm 380V 1st sanding unit Contact roll 180mm Engine 18.5kW 2nd sanding unit Combi aggregate with sanding pad Engine 11kW Sanding width max 1100mm Sanding height Min/max 4/170mm Throughput speed 4.5-9 m/mins Dimensions 2300x2205x2500mm, weight 1850kg - Documentation available: No - CE certificate present: No - Number of units [pcs]: 2 - └ Unit 1: - - Type of unit: Contact roller - - Roller diameter [mm]: 180 - - Motor power [kW]: 18.5 - └ Unit 2: - - Type of unit: Combi Iodswnh A Aepfx Abvsth - - Sanding belt length [mm]: 2620 - - Sanding belt width [mm]: 1115 - - Motor power [kW]: 11 - Max. working width [mm]: 1100 - Min. working height [mm]: 4 - Max. working height [mm]: 170 - Min. feed speed [m/min]: 4.5 - Max. feed speed [m/min]: 9 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2017, total height: 1,800 mm, total length: 4,800 mm, total width: 1,000 mm, Colour: Grey Price: On request - Details: - └ Description: Machine is currently giving fault, error code empty machine Isdoyll Snspfx Abvoth - Year: 2017 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Number of units [pcs]: 9 - └ 1st unit type: Pre-milling unit - - Tools available: Yes - └ 2nd unit type: Glue unit - └ 3rd unit type: Pressure rollers - - Tools available: Yes - └ 4th unit type: Cap unit - - Tools available: Yes - └ 5th unit type: Corner rounding unit - - Tools available: Yes - └ 6th unit type: Radius scraping unit - - Tools available: Yes - └ 7th unit type: Corner rounding unit - - Tools available: Yes - └ 8th unit type: Flat scraping unit - - Tools available: Yes - └ 9th unit type: Brushing unit - - Tools available: Yes - Glue system: Glue pot - Voltage [V]: 400 - Current consumption [A]: 42 - Transport dimensions: 4800mm x 1000mm x 1800mm (l x w x h) Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2011, total height: 2,000 mm, total length: 8,400 mm, total width: 1,080 mm, Colour: Grey Weight: 3.500 kg Price: On request - Year: 2011 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: AH/335516 - Number of units [pcs]: 12 - └ 1st unit type: Spraying device - - Tools available: Yes - └ 2nd unit type: Glue unit - └ 3rd unit type: Pressure rollers - - Tools available: Yes - └ 4th unit type: Cap unit - - Tools available: Yes - └ 5th unit type: Rough milling unit - - Tools available: Yes - └ 6th unit type: Corner rounding unit - - Tools available: Yes - └ 7th unit type: Radius scraping unit Iodpfx Asyudwzsbvjth - - Tools available: Yes - └ 9th unit type: Flat scraping unit - - Tools available: Yes - └ 10th unit type: Brushing unit - - Tools available: Yes - Voltage [V]: 400 - Current consumption [A]: 68 - Fuse [A]: 68 - Transport dimensions: 8400mm x 1080mm x 2000mm (l x w x h) - Transport weight [kg]: 3500kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: not inspected (used), Year of construction: 2020, max. workpiece length 6360 mm profile spindle 1 Stück main drive 13 kW Control Maestro SCM CNC Machining Center ACCORD 40 FX for windows and doors ----- Available as an OPTION at an additonal cost: extensive window and door tooling among others (window cutting available upon request!): Wooden windows IV 68, 78, 92 Wooden "style" windows Wood-aluminum windows Front doors Lift-and-slide doors Box windows Machine still in operation, available for viewing! Technical Summary (detailed description available upon request!): ----- - ??Working area X-Y = 6360 x 1905 Z = 350 - Automatic table with 8 support rails MATIC - L1825 - 5-axis spindle MAXI - Prisma T, HSK 63 E, 13 kW - RTCP Setting - Self-calibration system for Prisma work unit - Adjustable chip removal device on the electric spindle - Preparation for "Prisma T-S" angle gearbox - BRC - Working unit: Saw blade for face machining, 1 vertical milling cutter connection 3 vertical, independent drill heads, center distance 32 mm 3 vertical drill heads (not independent), center distance 21.5 mm, for mortise drilling 4 horizontal drill heads (2 per side, not independent), center distance 21.5 mm 2 horizontal milling heads (1 per (Page) - TRC 48 - Rear Tool Magazine 48 tool positions (excluding tool holders) Center-to-center distance between positions: 104 mm Max. tool diameter: 350 mm Max. tool length: 320 mm Max. weight per tool: 10 kg (15 kg with HSK 63 E spindle) Max. total weight on the magazine: 250 kg - MACH 5 - Quick-change system: Allows tool changes on the electric spindle in just a few seconds. - Pendulum operation - Automatic lubrication of the axes - eye-M operating console with integrated PC - Additional fixed control panel - TECPAD - Remote control of machine functions - Clamping jaw preparation H145 for worktable with 8 support rails - Front stop row H110 for worktable with 8 support rails - Rear stop row H110 for worktable with 8 support rails - Suction cup H110 145x145 mm - Swivel suction cup H110 145x55 mm - Swivel suction cup H110 180x65 mm - First side stop row H145 for worktable with 8 support rails Second side stop row H145 for worktable with 8 support rails Itjdpfx Ajy Hl Iysbvjh Clamp H145 with round base Clamp H145 with square base N.6 Lifting devices with double stroke H145 Laser and reference stop H145 for sheet (left) - PRO-SPEED safety system - Maestro CNC - Machine operator interface and programming - Maestro ProView - Simulation software Tools are sold in the condition, scope, and with accessories as they are currently in stock. Note regarding window cutouts, tool drawings, and tool system listings: Engelfried GmbH does not guarantee that the tools actually available correspond to the systems listed and drawn. (Technical specifications according to the manufacturer - without guarantee!)

Condition: used, Year of construction: 2023, Special price – Showroom machine Garbsen INDUSTRIAL AUTOMATIC EDGE BANDING MACHINE stefani md (the images of the machine are not binding with regard to the actual features specified below) KEY FEATURES EDGE BANDING OF SOLID WOOD UP TO 15 MM THICKNESS: SIMPLE AND FUNCTIONAL PROCESSING OF EDGES WITH LARGE DIMENSIONS "SGP" GLUE TANK: USE OF EVA AND POLYURETHANE GLUE FOR A PERFECT GLUE JOINT "STARTOUCH" CONTROL: A TOUCH IS ALL IT TAKES TO OPERATE THE MACHINE GENERAL FEATURES Automatic single-sided edge banding machine for applying edge banding with hot melt adhesive to the four sides of straight panels and for subsequent finishing. Machine frame and longitudinal supports made of cold-rolled steel in a box construction, manufactured in a single element, for high rigidity and vibration-free operation to accommodate the working units. Openings with slides for discharging any remaining chips to the floor. Upper pressure beam made of thick-walled steel construction and with columns made of cast iron, for a vibration-free structure where the working units are attached. Pressure rollers on the feed chain in a double row, made of rubber with a high coefficient of friction and with sliding on bearing rollers. Device to protect the pressure rollers from any remaining chips. Electronic adjustment of the upper pressure unit, depending on the panel thickness. Upper working units attached to the pressure beam or mechanically connected to ensure automatic adjustment when changing the panel thickness. Lower working units attached to the machine frame or to the longitudinal support, for a precise reference to the panel. All high-frequency motors are operated via frequency inverters. Protective cover for all units positioned after the gluing unit. Windows made of polycarbonate ensure a good view of the units during processing. Interior lighting of the cabinet. Protective cover with sound-absorbing material for lower noise emissions during processing. The spacer on the infeed guide allows the machine to be fed in the correct spacing. The spacing is automatically adjusted to the selected feed speed. Extraction nozzle arranged on the soundproof hood. Swivel control panel in an ergonomic position at the machine infeed. The electrical system complies with current regulations. Electrical components housed in a metal housing, attached to the machine frame and provided with doors for convenient access during any maintenance work. Panel feed The panel feed is carried out via a feed chain consisting of rubber sliding blocks with a high coefficient of friction, attached to a 1-1/4" industrial chain. The chain slides on 2 guides made of hardened and ground steel, a round guide and a flat guide, to guarantee a straight feed and protect against lateral displacement. Automatic lubrication of the chain. The amount of lubricating oil is optimized by the control system depending on the panels being processed. Support roller track externally and positioned along the entire length of the machine; consisting of an extendable opening system with sliding on linear bearings and plastic sliding rollers with steel pivot pins. "STARTOUCH" CONTROL Main features: 12" touchscreen color display Graphical representation of all processing units and their status (on/off) Iodpozc Ilxofx Abvsth