Used Swepac Fr 85 for sale (5,156)

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, 85 t x 2500 mm Weight: 9000 kg (without tools) Between columns: 2050 mm Itsdpfx Ajyxri Isfvsk Service: In 10/2023, the pump was replaced by TRUMPF at a cost of EUR 10,000. Since then, the machine has operated approximately 200 machine hours.

Condition: like new (used), Year of construction: 2024, clamping force: 27,000 kN, ENGEL DUO 36060/2700 TECH Manufacturer: ENGEL Model: DUO 36060/2700 TECH Clamping Force: 2,700 t (27,000 kN) CLAMPING UNIT Clamping force: 27,000 kN Opening stroke: 3,300 mm Max. daylight: 4,100 mm Min. mould height: 800 mm Max. mould height: 2,200 mm Tie bar spacing (H × V): 2,180 × 1,750 mm Platen dimensions (H × V): 2,970 × 2,640 mm Opening force: 770 kN Opening force with pressure pad: 1,600 kN Dry cycle time (Euromap 6): 5.6 s INJECTION UNIT Screw diameter: 190 mm L/D ratio: 25:1 Screw stroke: 850 mm Shot volume: 24,100 cm³ Theoretical shot weight PS: approx. 21.9 kg Injection rate: 2,620 cm³/s Injection pressure (regenerative): 1,300 bar Iedpfx Afezvc N Rovetk Maximum injection pressure: 1,600 bar Screw speed: 85 rpm Maximum screw speed: 100 rpm Screw torque: 24,000 Nm Reduced torque at max. speed: 20,400 Nm Plasticizing rate (3-zone screw): 238 g/s Plasticizing rate (barrier screw): 296 g/s NOZZLE Nozzle stroke: 1,300 mm Nozzle contact force: 210 kN EJECTOR Ejector stroke: 400 mm Ejector force forward: 420 kN Ejector force return: 420 kN HEATING SYSTEM Heating zones incl. nozzle: 12 Installed heating power: 160.9 kW DRIVE UNIT Installed motor power: 355 kW Reload pump motor: 3 kW Hydraulic oil tank capacity: 3,500 l COOLING REQUIREMENTS Cooling capacity: 66.9 kW Water consumption (32°C inlet): 5.88 m³/h Options: Engel VIPER 90 robot Rectable tie bar (movable) Hotrunners: 160 cores: 3+3 Cascades: 72

Condition: used, mileage: 1,001 km, power: 65 kW (88.38 HP), gearing type: automatic, fuel type: diesel, color: orange, overall weight: 7,400 kg, empty load weight: 6,700 kg, axle configuration: 4x4, number of seats: 1, first registration: 01/2006, Year of construction: 2006, operating hours: 7,975 h, front tire size: 405/70-24, rear tire size: 405/70-24, driver cabin: other, wheelbase: 2,270 mm, Equipment: additional headlights, all wheel drive, standard shovel, Vehicle location: Bovenden, rear window, working lights Wheelbase: 2270 mm Deutz diesel engine type 5F4L 2011, loading length approx. 5700mm! Height 3850mm Itodovhiq Aopfx Afvsk Approx. 7,975 operating hours! Various accessories (high tip bucket, pallet fork, bucket separator) available at extra charge! MB-HDS 214 bucket separator for 8.900,- EUR surcharge, see -8578-! ACCESSORY INFORMATION WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! - .

Condition: excellent (used), functionality: fully functional, Year of construction: 2006, operating hours: 5,898 h, load capacity: 4,000 kg, lifting height: 6,900 mm, free lift: 2,350 mm, load center: 600 mm, fuel type: gas, mast type: triplex, construction height: 3,200 mm, motor manufacturer: G.M., gearing type: hydrostat, fork carriage width: 1,360 mm, fork length: 1,200 mm, fork width: 150 mm, fork thickness: 50 mm, tire condition: 100 %, front tire type: cushion tires (black), front tire size: 200/50-10, rear tire type: cushion tires (black), rear tire size: 27X10-12, overall weight: 10,700 kg, empty load weight: 6,700 kg, total height: 2,400 mm, total length: 2,400 mm, total width: 2,250 mm, color: green, Equipment: CE marking, all wheel drive, cabin, lighting, pallet forks, sideshift, COMBILIFT C4000 | 2006 | 5,898 MTH | LPG | Triplex 6,900 mm | Fork Positioner | New Tyres | Condition 5/5 ✅ Optional: 4,050 mm spreader beam. Ready for work. No compromises. 🚀 This COMBILIFT C4000 has been fully serviced both technically and cosmetically, presenting itself as like new ✨. Built for demanding environments, it delivers reliable, downtime-free operation. 💪 Key specifications: 📌 Load capacity: 4,000 kg 📌 Mast: Triplex 6,900 mm | Free lift: 2,350 mm 📌 Fork positioner: 1,360 mm | Forks: 1,200 mm 📌 Tyres: superelastic 100% 🛞 (Front 200/50-10 | Rear 27x10-12) 📌 Heated full cabin 🔥 📌 Weight: 6,700 kg | Load centre: 600 mm 📌 Dimensions: H 2,400 mm | L 2,400 mm | W 2,250 mm | Mast height: 3,200 mm Isdpfxezva Drs Afvstk ✅ Fully serviced and inspected | ✅ Ready for immediate operation Ideal for: 🏭 Narrow aisles | 📦 Long loads | 🪵 Timber/Steel/Tubes | 🌦 Indoor & outdoor FT LOGISTICS 🛠 Full technical inspection & refurbishment 🚚 Transport across Europe 💶 Leasing support | 📄 Invoice in EUR/PLN 🔧 After-sales service & warranty

Condition: used, mileage: 15,244 km, power: 48 kW (65.26 HP), first registration: 01/2003, overall weight: 2,800 kg, fuel type: gasoline, color: white, axle configuration: 4x4, maximum load weight: 1,560 kg, empty load weight: 1,240 kg, tire size: 175/75R14, wheelbase: 2,150 mm, driver cabin: day cab, gearing type: mechanical, emission class: euro3, suspension: steel, loading space width: 1,330 mm, loading space length: 1,880 mm, loading space height: 350 mm, total length: 3,550 mm, total width: 1,400 mm, total height: 1,800 mm, number of seats: 2, Equipment: all wheel drive, cabin, Vehicle location: Bovenden, aluminum body, short cab, manual transmission, rotating beacon, leaf spring suspension, winter service equipment. Itodjvhhc Dopfx Afvjk Wheelbase: 2150 mm, Body: pre-equipped for winter service with a spreader. New clutch. Snowplow available for an additional charge of 1,000 EUR! 4-cylinder Daihatsu engine. Vehicle is in a condition requiring repairs! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to change, prior sale, and errors!

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, machine/vehicle number: 113201690006, type of input current: three-phase, input voltage: 400 V, input frequency: 50 Hz, Equipment: documentation/manual, This device is a component of an entire production line, which has not been in use since 2022. The entire line consists of 6 such devices, which are grouped in pairs. Each pair of devices has its own control cabinet/switchboard. The entire system is controlled from a main switchboard. The entire system, or individual components, will be sold. Itedezt Npropfx Afvsk

Condition: used, Second-hand machine Features and technical specifications: - JN-85 PS semi-automatic pallet strapping machine - The semi-automatic pallet strapping machine is suitable for a wide range of packaging requirements, making it a versatile choice for numerous sectors, including logistics, manufacturing and retail. It meets various requirements for packing goods onto pallets. - The mobile design of this model allows for convenient operation, particularly in confined workspaces with manual lifting equipment that are inaccessible to cranes. - The compact design of this model allows for flexible use, meaning the machine can be used even in confined spaces where other machines cannot fit, thereby maximising the use of the available workspace. - The semi-automatic pallet strapping machine is an indispensable tool in the packaging industry and has been designed to optimise and streamline the process of securing goods onto pallets. Given the growing demand for efficient packaging solutions, investing in such machines can have a significant impact on productivity and operational efficiency. - Length of conveyor belt: 1000 mm (standard) - Min. packaging height: 550 mm - Motor: 1.23 kW / 230 V Itodpfx Afezlbttjvok Availability: at short notice Storage location: 63934 Röllbach

Condition: good (used), Code: 0353 Brand: SCM Model: SIGMA 85 KC - CE Standard Electronic horizontal panel saw with clamps for precise cutting of panels, suitable for joinery, furniture, custom made furniture, doors, kitchens, plastics, composite materials and various – CE Standard Technical data: Cutting length 3200 mm Cutting width 3200 mm Blade projection 85 mm Blade carriage feed speed 6–30 mt/min N°7 panel clamps to ensure the pack is held securely in place Main blade diameter 350 mm Hole 80 Main blade motor 11 Kw Main rotation speed 3900 rpm Scoring unit diameter 160 mm - Hole 55 – Motor 1,5 kW Automatic aligner: ensures precision during cross-cuts, reducing processing times Itsdpfey A Svpox Afvek N°3 front panel support surfaces Suction inlet diameters: n° 2 diameter 120 - n° 1 diameter 150 Compressed air 7-8 bar Overall dimensions of assembled machine mm 5700 x 4350 x 1700 h Weight kg 3300

Condition: reconditioned (used), Year of construction: 1998, functionality: fully functional, machine/vehicle number: 265134, warranty duration: 6 months, year of last overhaul: 2026, Equipment: type plate available, Multimatic MUS 6 WP Bakery Divider. Fully automatic machine for dividing and rounding dough. Designed for doughs with a yield (TA) of 148-160. Key features: Iodpjuv Hrwefx Afvstk - Capacity: up to 12,000 pieces/hour, - Weight range: 28 - 85 g, - Number of rows: 6, - Hydraulic system for the main piston, - Condition: as new (after complete overhaul), - Hopper volume: 50 l, - Round product, - Constructed of stainless steel.

Condition: reconditioned (used), functionality: fully functional, Power connection: 230V, 1.5kW Current consumption in operation: 5.5A Cutting height approx. 80 mm Cutting length 150 mm Itodpfoyypfpsx Afvek Dimensions (W x H x D): 500 x 570 x 750 mm Weight approx. 50 kg Handwheel height adjustment Swivels right/left 45° Tiltable 45°

Condition: good (used), Year of construction: 1994, power: 30 kW (40.79 HP), Drum chipper with horizontal feed max. feed width: 300 mm max. feed height: 85 mm Iedou Ezp Aepfx Afvjtk motor: 18.5 kW new rotor bearing

Condition: good (used), Year of construction: 2011, Tool holder: HSK 63 Turning spindle: 85 Spindle speeds: 20,000 rpm Chain magazine: 60 positions Table size: 400 x 500 mm Table load: 500 kg Chip conveyor Pallet changer Coolant filtration system KS high-pressure system through the spindle Itedpfozvb Tuox Afvjk

Condition: used, Year of construction: 1999, x-travel 12000 mm y-travel 3600 mm z-travel 1500 mm spindle turning speed range 3000 U/min Control: Heidenhain iTNC430 Milling head 2 axes, indexed 2.5° Itodjxwdygspfx Afvek Vertical (Y-axis): 3600 mm Transverse (Z-axis): 1500 mm Longitudinal (X-axis): 12,000 mm Guide rail length: 14,700 mm Guide rail width: 1400 mm Lowest milling position of the spindle nose measured from the floor (head horizontal): 855 mm Low column design 870 x 900 x 2,625 mm: 3,000 kg High stand design 870x900x3,025 mm: 3,500 kg Motor power: 37 kW Mounting: ISO 50/ DIN 69871-A Speeds: 11.7:231:3000 rpm Feed range: 2:2500 mm/min Rapid traverse X-axis: 12000 mm/min Z-Y axis: 15000 mm/min Feed motor power X-axis: 55 Nm Z-axis: 37 Nm Y-axis: 37 Nm Accuracy Positioning accuracy: 0.025 mm Repeatability: 0.015 mm Weight: approx. 42,000 kg Air supply to the machine: 300 L/min at 4.5 bar NOTE: The clamping plates and chip conveyors are not included in the scope of delivery. However, we can offer you both used and new clamping plates and chip conveyors on request.

Condition: used, Mitsubishi FREQROL FR-SF-2-26K-TCG AC Spindle Controller / Spindle Drive For sale is a used Mitsubishi FREQROL FR-SF-2-26K-TCG AC Spindle Controller, removed from a MAZAK MULTIPLEX CNC turning center. The unit shows normal signs of use and handling consistent with its age and industrial application (see original photos). The Mitsubishi FREQROL FR-SF series is designed for precise spindle motor control in CNC machine tools, offering reliable performance in demanding industrial environments. Technical Specifications Manufacturer: Mitsubishi Electric Series: FREQROL Model: FR-SF-2-26K-TCG Type: AC Spindle Controller / Spindle Drive Voltage Class: 200 V Application: CNC machine tools, turning centers, machining centers, spindle motor control Ijdpfx Aezn Ak Eofvotk Origin Removed from: MAZAK MULTIPLEX CNC Turning Center Professionally dismantled Condition Used Normal cosmetic wear from industrial use Please refer to the photos for the exact condition Sold exactly as shown Functionality: Untested (or Fully functional when removed from service, if applicable) Scope of Supply 1 × Mitsubishi FREQROL FR-SF-2-26K-TCG AC Spindle Controller Only the items shown in the photos are included Note This is a used industrial component and may show signs of wear due to previous use. The photographs are an integral part of the item description. Please verify the model and part number before purchasing to ensure compatibility with your machine.

Condition: used, Year of construction: 2013, General information Colour: Rot Weights Empty weight: 1.250 kg Functional Lifting capacity: 200 kg Working height: 1.990 cm CE mark: yes Condition General condition: average Technical condition: average Visual appearance: average Other information Delivery terms: EXW Transport dimensions (LxWxH): LxB 7,65 x 1,65 m Production country: DE Additional information Please contact Christian Theißen for more information Units: 912522 Manufacturer: Emminghaus Model: Pionier 85-6-20 Year of build: 2013 Condition: Used Data: Max. lifting height: 19,90 m bei 85° Lifting capacity: 200 kg Platform dimensions LxW: 1,25 x 0,90 m Platform dimensions extended LxW: 2,08 x 1,32 m Support width: 4,00 x 4,00 m Transport dimensions LxW: 7,65 x 1,65 m Itjdpfjv Tc Ryex Afvjk Weight: 1.250 kg Special features: can be rotated on chassis, ball-head coupling.

Condition: like new (used), Year of construction: 2021, functionality: fully functional, Weiler Praktikant VCD Precision Lathe (2021) Manufacturer: Weiler Model: Praktikant VCD Precision Lathe Year of manufacture: 2021 Condition: Used, excellent, like new, incl. new maintenance and measurement protocol prior to sale Centre distance: 650 mm Centre height: 160 mm Swing over bed: 320 mm Swing over cross slide: 190 mm Cross slide travel: 150 mm Top slide travel: 110 mm Top slide swivel range: +/-65° Bed saddle guideway length: 350 mm Bed width: 205 mm Tool shank cross-section (H x W): 20 x 20 mm Iodpfx Afoztyrqevjtk Height from top slide to turning centre: 30 mm Spindle head according to ISO DIN 702-3 (DIN55027) size 5 Spindle diameter in front bearing: 70 mm Spindle bore: 43 mm Main spindle taper metric 50 Drive power: 6 kW Speed range: 30 – 4,000 rpm Number of gear stages: 1 Number of speeds: stepless Number of feeds: 24 Longitudinal feed: 0.02 – 0.63 mm/rev Facing feed: 0.006 – 0.2 mm/rev Quill diameter: 40 mm Quill stroke: 85 mm Quill taper: 3 Morse taper Weight, without packaging and accessories: approx. 1,150 kg Dimensions (L x W x H), net: 1,720 x 890 x 1,700 mm Headstock / Rear cover / Sliding guard: Light grey RAL 7035 Machine base / Machine bed: Basalt grey RAL 7012 Display housing: Blue NCSS 4550-R80B

Condition: good (used), functionality: fully functional, fuel type: diesel, Year of construction: 1999, operating hours: 10,200 h, Equipment: all wheel drive, cabin, Kawasaki 85Z2 wheel loader, weight 19,200 kg, year of manufacture 1999. The loader is in good condition and ready for operation. Location: Ampfing, Bavaria. Transport and delivery possible. Inquiries welcome at any time. Itedpfx Afsy Rh I Rsvok

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. Isdszp H R Ejpfx Afvjtk This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Year of construction: 2019, condition: used, functionality: fully functional, This is a tilting frying pan from the premium manufacturer MKN, type Optima 850 Gas 3/1 GN with motor-assisted tilting. The unit has undergone a comprehensive inspection in our in-house workshop and is fully functional, with a 6-month warranty on all electrical components. The tilting frying pan is in good used condition, free of defects, and is mounted on legs. If required, the legs can be removed so that the unit can also be mounted on a plinth. The manufacturer's list price is €29,140 net. Our price: €8,226.89 net = €9,790 gross. You will receive an invoice with VAT shown. Our used equipment service for you: * 6-month warranty on all electrical parts, limited to the replacement of defective parts, excluding installation and removal costs. * High-quality branded equipment at fair prices. * Professional overhaul/inspection and expert cleaning. * Tested & fully functional - or your money back. * Flexible shipping or self-collection options. * Competent advice - before and after purchase. * Provision of operating instructions, connection diagrams & spare parts. * Inspection according to DGUV V3. Technical data: * W x D x H: approx. 1600 x 850 x 850 mm (without legs 700 mm) * Pan interior dimensions: 1020 x 540 x 210 mm deep * Power connection: V: 220-240 / kW: 17 * Type: 10019153 * Serial number: 19207555 * Year of manufacture: 2019 * Nominal capacity / Usable capacity: 116 / 94 liters Condition: Used, comprehensively inspected, fully functional. Further details: * Optimized nominal capacity: 116 liters * Usable capacity: 94 liters * The front-mounted pivot point of the pan and the shape of the pouring opening prevent the pouring stream from wandering and scattering, guaranteeing complete emptying. * 55 mm cleaning gap between the pan and the side frame. * Standard equipment includes a double-walled hinged lid and mixing tap. * The pan base is made of a special sandwich material as standard for even heat distribution. * Thermostatic temperature control. Shipping: * Delivery or self-collection by arrangement. * Worldwide shipping on request. * Shipping to islands or mountain stations only by arrangement. Ijdjzu Rpvjpfx Afvotk Subject to changes and errors. Do you have any questions, would you like to receive advice, or would you like to see something on-site? You can reach us by telephone during our opening hours: Monday to Friday, 9:00 a.m. to 1:00 p.m. and 2:00 p.m. to 5:00 p.m. Sales are exclusively subject to our general terms and conditions (GTC).

Condition: used, The Graule ZS 85 N mitre saw is designed for cutting to length and making mitre cuts: it can be swivelled and tilted. Cutting height 85 mm Cutting length 380 mm Iedsztvy Ropfx Afvetk Technical data: - Motor: 1.5 kW - Connection: 380 V

Condition: used, mileage: 281,492 km, power: 100 kW (135.96 HP), first registration: 09/2008, fuel type: diesel, overall weight: 3,500 kg, next inspection (TÜV): 05/2027, color: yellow, gearing type: mechanical, emission class: euro4, number of seats: 3, loading space length: 3,400 mm, loading space width: 2,050 mm, Year of construction: 2008, Equipment: ABS, central locking, electronic stability program (ESP), soot filter, * German vehicle, second owner Iodezvit Nepfx Afvjtk * Manual transmission, 6 gears * 3 seats * Wheelbase 3665 mm * Platform body, 3.40 m, tie-down points, loading height approx. 85 cm * Ladder rack * 2 rotating beacons * ASR (Anti-Slip Regulation) * Tires with approx. 50% tread * Tachograph * Tow hitch, ball type, 2,800 kg * Euro 4 * I will gladly send a video via WhatsApp * WhatsApp: * Polish contact: [phone number] * Sale only to businesses, no warranty, all information without guarantee, subject to prior sale Special equipment: Connection terminal, audio system RCD 2001, exterior mirrors electrically adjustable and heated, on-board tools and jack, digital tachograph, reinforced rear suspension, spare wheel with road tires, rear wall with window, interior mirror with automatic anti-glare function, seats in the cab: double passenger seat, reinforced rear stabilizer, reinforced front stabilizer, underride guard at the rear Additional equipment: Airbag for driver, traction control system (ASR), body/structure: standard platform, engine 2.5 L - 100 kW TDI DPF, wheelbase 3665 mm, seat cover/upholstery: fabric, seats in the cab: driver's seat adjustable, steel rims 6.5x16, permissible total weight 3.50 t

Condition: like new (used), Year of construction: 2025, operating hours: 650 h, functionality: fully functional, total height: 2,274 mm, total length: 3,061 mm, total width: 2,129 mm, feed length X-axis: 15,000 mm, feed length Y-axis: 15,000 mm, feed length Z-axis: 15,000 mm, type of input current: three-phase, grinding wheel diameter: 150 mm, overall weight: 3,300 kg, rotational speed (max.): 10,500 rpm, travel distance X-axis: 320 mm, travel distance Y-axis: 200 mm, travel distance Z-axis: 470 mm, input current: 30 A, input frequency: 50 Hz, input voltage: 400 V, space requirement width: 3,000 mm, space requirement length: 4,000 mm, space requirement height: 3,000 mm, Equipment: rotational speed infinitely variable, WALTER CNC Grinding Machine HELITRONIC MINI PLUS (RAPID version) GE Fanuc Series 31i - B5 2025 650 working house. please see all information in attached PDF file * Machine Type: WALTER CNC Grinding Machine HELITRONIC MINI PLUS (RAPID version) * Fire extinguishing system DIMES * Holder for sharpening stones * Tool gripper * Protective and cleaning arbor * Plug gauge * Setting disc * Pull stud * Clamping arbor for hobs (diameter 32 mm) * Clamping arbor for hobs (diameter 40 mm) * Foot operated switch Ijdpfxjztti As Afvetk * Keyboard shelf * Standard grinding wheel adaptor (HSK50 form A, d20, D50, L55, L1=25 mm) * Standard grinding wheel adaptor (HSK50 form A, d20, D50, L55, L1=45 mm) * Standard grinding wheel adaptor (HSK50 form A, d20, D50, L55, L1=85 mm) * Dynamometric Key / torque wrench * Dynamometric Key * Mounting wrench * Sensor * Coolant unit Location in Israel . ready for inspaction . need export license

Condition: used, Year of construction: 2005, functionality: fully functional, Equipment: CE marking, HOMAG OPTIMAT BAZ211 VENTURE 20 (Router No. 5) Year of manufacture: 2005 Basic structure and drives • Machine bed: Heavy-duty, stable design with compact linear guides. • X and Y axis drives: Digital AC servo motors and rack and pinion gears with pre-tensioning for backlash-free operation. • Z axis drive: Digital AC servo motor with ball screw; travel range is 535 mm. • Lubrication: Manual central lubrication for all drives and linear guides. Main spindle and C axis • Power: 11 kW in S6 mode (7.5 kW in S1). • Cooling: Liquid-cooled, vector-controlled asynchronous motor. • Speed range: Continuously programmable from 0 to 18,000 rpm. • Tool holder: HSK F63 according to DIN 69893. • C axis: Equipped with an aggregate interface, pneumatic interface, and 3-point support. Clamping system (Cantilever table) • Cantilevers: 6 pieces with a tubeless, dual-circuit vacuum system. • Stops: 6 longitudinal stops in the cantilevers (stroke 140 mm) and 2 adjustable lateral stops. • Suction cup equipment: • 10x dual-action vacuum suction cups (160x115x100 mm), 4 with integrated lift. • 2x dual-action vacuum suction cups (125x75 mm). • Pneumatics: 4 connections with a single-circuit system for mechanical clamps. Workpiece dimensions • Length (X): Max. 3050 mm (individual setup) or 900 mm (shuttle mode). • Width (Y): Max. 1220 mm for milling; max. 1150 mm for all aggregates. • Thickness (Z): Max. 60 mm with standard suction cups; up to 300 mm including fixtures for top-side milling. • Minimum thickness: 12 mm for chamfering, 16 mm for radius milling. Tool changer and accessories • Type: Disc-type tool changer (12 positions) for HSK F63 tools and aggregates. • Diameter capacity: 12x max. 135 mm, or a combination of 6x 180 mm and 6x 85 mm. • Vacuum system: Liquid ring pump with a capacity of 66 m³/h (equivalent to 100 m³/h for vane pumps). Control system (Power Control PC85) • Hardware: Industrial PC (2 GHz) with 512 MB RAM, a hard drive for data and a second for backup (cloning). Ijdpozr N H Ujfx Afvetk • Software: • woodWOP: Graphical interface for CNC programming. • woodDesign: 3D interface for furniture design. • woodScout (optional): Graphical diagnostic system. • Communication: Ethernet card and modem for remote diagnostics.

Condition: good (used), Year of construction: 2004, functionality: limited functionality, travel distance X-axis: 560 mm, travel distance Y-axis: 610 mm, travel distance Z-axis: 625 mm, rapid traverse X-axis: 60 m/min, rapid traverse Y-axis: 60 m/min, rapid traverse Z-axis: 60 m/min, controller manufacturer: Okuma, controller model: OSP-E100M, workpiece length (max.): 600 mm, workpiece width (max.): 710 mm, workpiece weight (max.): 400 kg, total height: 2,760 mm, total length: 4,535 mm, total width: 2,415 mm, table width: 400 mm, table length: 400 mm, table load: 400 kg, overall weight: 10,000 kg, spindle speed (max.): 8,000 rpm, distance table center to spindle nose: 710 mm, spindle motor power: 15,000 W, spindle nose: BT40, number of spindles: 1, number of slots in tool magazine: 40, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, rotational speed infinitely variable, Okuma Space Center MA400HA Horizontal Machining Centre Machine Type: CNC Horizontal Machining Centre Year: 2004 Control: OSP-E100M Axes: 4 No. of Pallets: 2 Condition: Good - There is an issue with the pallet changer. Includes Cromar Swarf Conveyor Coolant Filtration System Technical Specifications Pallets: 2 Size of Pallets: 400 x 400mm X Axis Travel: 560mm Y Axis Travel: 610mm Z Axis Travel: 625mm B Axis Travel: 360 Deg Rapid Traverse: 60m/min Spindle Centre to Pallet Top: 50 - 660mm Spindle Nose to Pallet Centre: 85 - 710mm Max Pallet Load: 400kg Max Workpiece Dimensions: 600 x 710mm Tool Pockets: 40 Spindle Taper: BT40 Iodpjwcd Evsfx Afvjtk Spindle Power: 15kW Spindle Speed: 8,000rpm Machine Dimensions: 4535 x 2415 x 2760mm Machine Weight: 10,000kg Notes: *Specifications are given in good faith but not guaranteed*

Condition: excellent (used), functionality: fully functional, Year of construction: 2013, operating hours: 7,550 h, load capacity: 4,000 kg, lifting height: 8,500 mm, free lift: 2,500 mm, load center: 600 mm, fuel type: gas, mast type: triplex, construction height: 3,700 mm, motor manufacturer: GM, gearing type: hydrostat, fork carriage width: 1,500 mm, fork length: 1,200 mm, tire condition: 100 %, front tire type: cushion tires (black), front tire size: 21 X 9 - 15, rear tire type: cushion tires (black), rear tire size: 28 X 12,5 - 15, overall weight: 12,550 kg, empty load weight: 8,550 kg, total height: 2,350 mm, total length: 1,900 mm, total width: 1,650 mm, color: green, Equipment: CE marking, all wheel drive, cabin, lighting, pallet forks, sideshift, # 🚜 COMBILIFT CB4000 | ⛽ LPG | ⬆️ TRIPLEX 8500 MM | ⚙️ FORK POSITIONER | ↔️ SIDE SHIFT | 🔝 FREE LIFT | ✅ READY TO WORK 🔧 FULLY SERVICED | 🛡️ WARRANTY | 🌍 WORLDWIDE DELIVERY Looking for a reliable multidirectional forklift that starts generating profits from day one? This COMBILIFT CB4000 has been fully inspected, serviced, and tested for immediate operation. ## ⭐ KEY ADVANTAGES ✅ Fully serviced before delivery 🛡️ Start-up warranty 🛞 Brand new 100% super elastic tires 💪 4000 kg lifting capacity ⛽ Reliable GM LPG engine 🔝 2500 mm free lift ⚙️ Hydraulic fork positioner ↔️ Side shift 💡 LED working lights 🚨 Warning beacon 🚀 Ready for immediate work 🎥 Live online demonstration 🚛 Worldwide delivery ## 📋 TECHNICAL SPECIFICATIONS 🏭 Manufacturer: COMBILIFT 🚜 Model: CB4000 📅 Year: 2013 ⛽ Power: LPG 🔩 Engine: GM Isdpfxozua Ubj Afvstk ⏱️ Operating Hours: 7550 h 🏋️ Capacity: 4000 kg ⚖️ Weight: 8850 kg ⬆️ Mast: Triplex 📏 Lift Height: 8500 mm 🔝 Free Lift: 2500 mm ⚙️ Fork Positioner: 1500 mm 📐 Fork Size: 1200 × 150 × 50 mm ↔️ Side Shift: Yes 🏠 Operator Station: Open ## 📐 DIMENSIONS 📏 Overall Height: 2350 mm 📏 Collapsed Mast Height: 3700 mm 📏 Overall Length: 1890 mm 📏 Overall Width: 1650 mm ## 🛞 TIRES 🔹 Front: 21 × 8-15 Super Elastic 🔹 Rear: 28 × 12.5-15 Super Elastic ✅ Condition: 100% New ## ⚙️ EQUIPMENT ⚙️ Hydraulic fork positioner ↔️ Side shift ⬆️ Triplex mast with free lift 💡 LED working lights 🚨 Warning beacon 🛞 Super elastic tires ## 🏗️ IDEAL FOR 🪵 Timber industry 🏭 Steel service centers 🔩 Steel fabrication 📦 Pipes, profiles & long loads 🚚 Warehouses & logistics 🌦️ Indoor & outdoor operation ## 🤝 WHY FT LOGISTICS 🔧 Every machine is fully serviced, inspected, and tested before delivery. 🌍 Over 100 forklifts in stock with worldwide delivery across Europe, Africa, Asia, the Middle East, and South America. ## 🌍 WE PROVIDE 🔧 Pre-delivery service 🛡️ Warranty 👨‍🔧 Technical support 💳 Leasing & financing 🚛 Worldwide transport 📄 Export documentation 🤝 After-sales support 🎥 Live demonstrations, photos, and videos on request. ## FT LOGISTICS ### 🚜 We Deliver Machines Ready To Work.