Used Tablet Press for sale (12,447)

Condition: ready for operation (used), Year of construction: 2004, machine/vehicle number: 1729, functionality: fully functional, empty load weight: 10,000 kg, workpiece width (max.): 5,500 mm, workpiece height (max.): 980 mm, Equipment: CE marking, Submitting a bid obligates you to collect the item on time, no later than June 22, 2026! TECHNICAL DETAILS Workpiece width max.: 5,500 mm Workpiece height max.: 980 mm Number of working stations: 8 Number of cylinders per press level: 10 Number of clamping devices per press level: 10 MACHINE DETAILS Power of main motor: 1.5 kW Press drive: Hydraulic Dimensions & Weight Dimensions (L x W x H): 8,000 x 2,200 x 2,450 mm Unladen weight: 10,000 kg Csdpfoy Tviuox Alworc Transport packages: 1 EQUIPMENT CE marking Separate press stages Motorized rotation 2 working stations per side

Year of construction: 1999, condition: ready for operation (used), functionality: fully functional, workpiece length (max.): 2,200 mm, workpiece width (max.): 800 mm, workpiece height (max.): 40 mm, stroke length: 150 mm, machine/vehicle number: 52850199, TECHNICAL DETAILS Maximum plate size: 2,200 x 800 mm Maximum plate thickness: 40 mm Maximum stroke: 150 mm Working pressure: 6 kg/cm² Total working pressure: 160 tons MACHINE DETAILS Total power: 17.3 kW Heating power: 13 kW Voltage: 380 V Current: 35 A Cjdpfxoy Tn R Rs Alworc Dimensions & Weight Dimensions (L x W x H): 3,900 x 1,800 x 2,100 mm Weight: 5,900 kg EQUIPMENT Heating 8 cylinders, each with a diameter of 100 mm Heating boiler included

Condition: used, Year of construction: 2003, machine/vehicle number: 0-306-04-2737, working width: 800 mm, conveyor belt length: 4,800 mm, feed rate X-axis: 37 m/min, working height: 1,400 mm, working length: 2,300 mm, No minimum price – guaranteed sale to the highest bidder! The machine must be collected between June 10, 2026, and June 30, 2026! TECHNICAL DETAILS Workpiece width max.: 800 mm Workpiece length max.: 2,300 mm Workpiece height max.: 1,400 mm Crsdpfoy Uwmqjx Alwoc Feed rate max.: 37 m/min MACHINE DETAILS Machine length: 4,800 mm EQUIPMENT Infeed conveyor Outfeed conveyor The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8536

Condition: used, Year of construction: 2002, machine/vehicle number: 0-306-04-1262, working width: 600 mm, conveyor belt length: 3,000 mm, feed rate X-axis: 40 m/min, working height: 1,300 mm, working length: 2,500 mm, No minimum price – guaranteed sale to the highest bidder! The machine must be picked up between June 10, 2026, and June 30, 2026! TECHNICAL DETAILS Workpiece width max.: 600 mm Workpiece length max.: 2,500 mm Workpiece height max.: 1,300 mm Workpiece width min.: 120 mm Workpiece length min.: 300 mm Workpiece height min.: 300 mm Feed rate max.: 40 m/min Conveyor belt length: 3,000 mm MACHINE DETAILS Crodpfxoy Uv Iys Alwjc Control system: NC 16 EQUIPMENT Unloading conveyor belt CE marking The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at its destination. External reference: 8535

Condition: refurbished (used), functionality: fully functional, The 2024 general overhaul includes, among other things, the die roller, the hydraulic nut, the bearings, the main shaft, the oil pump with filter, and synthetic oil. Only the steel housing is older, but it is in excellent condition. The images of the production line in the hall are from before the overhaul. The individual images of the Amandus Kahl pellet press show the condition after the overhaul. TECHNICAL DETAILS Crodpfx Aszaricelwec Motor power: 110 kW Sawdust capacity: 2.5 – 3 t/h Biomass capacity: 3 t/h Bran capacity: 3.5 – 4 t/h Straw capacity: 2 – 2.5 t/h MACHINE DETAILS Motor year of manufacture: 2024 Cooler with sieve year of manufacture: 2015 Conveyor belt year of manufacture: 2015 Feed screw year of manufacture: 2015 EQUIPMENT Amandus Kahl C35-780 pellet press with base plate New 110 kW electric motor Electric control cabinet with emergency stop Complete electrical documentation Conveyor belt Sieve system with automatic cooling Hydraulic nut Die roller Electrical wiring Metering screw for product feed Automatic metering system for filling 4 additional dies of 6 mm 60 liters of additional synthetic oil 7 new bearings 2 new wear rings 1 new air filter 2 new oil seals 1 new oil filter 1 new oil pump 20 liters of 800/460 synthetic oil 1 new pressure piece (main shaft) Documentation of the overhauled and renewed parts

Condition: used, machine/vehicle number: 008256, Max width workable: 800 mm Max length workable: 2500 mm Max height workable: 1340 mm Max feed speed: 40 m/min Cjdpfxjx A Hfvj Alwerc

Condition: used, machine/vehicle number: 008254, Max width workable: 700 mm Cedpfx Asx A Hfpelworc Max length workable: 2600 mm Max height workable: 1300 mm

Condition: used, machine/vehicle number: 008341, Max working length: 2480 mm Max working width: 880 mm No of Pressing cylinders: 4 Crodpfx Aox A Tf Ajlwec No of Daylights: 1

Condition: used, Year of construction: 1999, color channels: 8, We offer this used Heidelberg Speedmaster 74 8 Color Plus Coater 4/4 offset printing press, year of construction 1999. Manufacturer: Heidelberg Model: Speedmaster 74 8 Color Plus Coater Perfecting 4/4 or Straight Crodpfxeynvurj Alwjc Year of manufacture: 1999 Console CPC 1.0.4 Technotrans Cooling Unit Condition: used Category ID: 839 Type ID: 520 Type: offset printing press If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: new, functionality: unexamined, Year of construction: 2024, machine/vehicle number: 16.41-PS0382, control type: CNC control, degree of automation: automatic, actuation type: electric, sheet thickness (max.): 8 mm, input voltage: 400 V, input current: 20 A, type of input current: three-phase, 2024 Pima Power PS 1225 Brand new Complete machine. Machine was tipped on its side during transit and was damaged. Crodpfx Alew Nbh Hewec Machine is stored in Our warehouse in California USA. Contact to set up in person inspection.

Year of construction: 2018, condition: good (used), functionality: fully functional, in total 7 FMTM250-7HS-32P FUSEI mold presses, year of manufacture 2011-2018, and also some Fujiwa mold presses, vintage 2002-2005 available Codoxniklopfx Alwsrc

Condition: refurbished (used), Year of construction: 2020, functionality: fully functional, power: 4 kW (5.44 HP), pressing force: 80 t, stroke length: 60 mm, Power: 80 Ton Table size: 680 x 540 mm Strokes per minute: 60/min. Stroke: 60 mm Throat depth: 275 mm Crodpfxezbvvve Alwoc Gap in bed: 150 mm Controll: 2- hand controller Country of origin: Netherlands Motor power: 4 kW Machine (L×W×H): 175 x 100 x 235 cm Machine weight: 3700 kg

Condition: good (used), Year of construction: 2017, functionality: fully functional, power: 11 kW (14.96 HP), pressing force: 100 t, stroke length: 300 mm, operating speed: 10 mm/s, Equipment: CE marking, safety light barrier, Bending capacity: 100 Ton Bending length: 3100 mm Backgauge: 550 mm Stroke length: 300 mm Bending speed: 10 mm/sec Crsdpfezbvuljx Alwoc Supplied with: - 2 support arms - Integrated safetyscreen - 6 axis controlled Y1, Y2, X, R, Z1, Z2 - Cabinet with many tools - User manuals Country of origin: Netherlands Motor power: 11 kW Machine (L×W×H): 400 x 230 x 290 cm Machine weight: 6350 kg

Condition: reconditioned (used), Year of construction: 2007, operating hours: 13,209 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,050 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 700 mm, bale weight: 500 kg, oil tank capacity: 400 l, power: 15 kW (20.39 HP), year of last overhaul: 2025, volume flow: 108 m³/h, Technical data baler: Manufacturer according to type plate BRAMIDAN (original manufacturer Presto GmbH & Co. KG) Type HC 50 (corresponds to the Presto HPK 50) Year of manufacture 2007 Operating hours 13,209 hours, as of March 2026 Number of bales pressed: 23,379 bales Pressing force 50 tonnes Specific pressing force 650 kN/m² Feed chute dimensions 1250 x 1050 mm (L x W) Filling volume 0.96 cm³ Theoretical cycle time 32 seconds Theoretical throughput capacity 108 m³/hour Bale dimensions 1100 x 700 mm (w x h) length variable Drive power 15 kW Power consumption, total in 50 A Tying 4-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm approx. 3.1 t/hour Bulk weight of 60 kg/cbm approx. 4.5 tonnes/hour Bulk weight of 100 kg/cbm approx. 7.2 tonnes/hour Bale weights with a bale length of approx. 1.2 m up to 500 kg, depending on material Hydraulic oil tank capacity 400 litres PLC control Siemens S7-200 Effective transport dimensions excluding baler 6850 x 1950 x 2650 mm (l x w x h) Transport weight of press 8.5 tonnes Condition of the baler: The press was used in a production facility exclusively for pressing cardboard and was regularly serviced. With only 13,209 operating hours, the machine has seen little use. The press was partially overhauled in our workshop and then tested. The following overhaul work was carried out: Machine cleaned Bale retainer made operational and lubricated Light barrier replaced Twisting unit completely dismantled, broken down into individual parts, all bearings replaced, all plastic glides replaced, lubricated, chain tension adjusted Codpozbxyqjfx Alwerc Knife and counter knife dismantled, sharpened, reassembled Knife gap readjusted General maintenance work carried out and lubricated Scope of delivery: 1 baler with wire coil boxes, without wire (6850 x 1950 x 2650 mm) 1 bale chute (5100 x 1150 x 450 mm) 1 floor-mounted wire coil box (1450 x 380 x 360 mm) To transport the baler, you will need a tautliner with an effective internal height of 2700 mm. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, oil tank capacity: 600 l, power: 22 kW (29.91 HP), year of last overhaul: 2025, volume flow: 530 m³/h, For sale is a partially refurbished Presona baling press, with 50 t pressing force, 22 kW drive power, built in 2005 Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced Codpfszbxxaox Alwjrc All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the whirling unit replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, For sale is a complete Bollegraaf baling system consisting of conveyor technology, baling press and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical Throughput rate at a bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Codpfx Aozbxw Aelwjrc Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Comments: The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Crodpfxszbxwij Alwsc Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, year of last overhaul: 2025, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Codpjzbxvlsfx Alwerc Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2013, functionality: fully functional, Used Durma press brake Crodszbhnkspfx Alwoc Type AD S 30175 Capacity 3050 x 175 tons Delem DA66T control system Y1, Y2, X and R axis CNC controlled CNC crowning Amada / Euro clamp Includes a set of tooling

Condition: good (used), Year of construction: 2008, functionality: fully functional, Well-maintained, used E Brake by Safan Type E Brake 100 3100 Capacity 3100 x 100 tons Y1, Y2, X, R, Z1, and Z2 CNC controlled Manual crowning Cjdpfszbhk Esx Alwjrc Hydraulic Wila NS top clamp

Condition: refurbished (used), Year of construction: 2008, Used AMADA press brake: Illustrative image, machine in stock but not yet prepared. It will be in the same condition once it has been refurbished. Cjdpfozbg Sbsx Alwjrc Year: 2008 Type: HFE400-4L Capacity: 4000 x 400T Number of axes: 6 Stroke of cylinders: 350 mm Rapid traverse speed: 100 mm/sec Installation of new, high-tonnage tooling along the entire length Machine completely refurbished upon order.

Condition: good (used), Year of construction: 1996, Well-maintained, used press brake from Beyeler / Bystronic. Crsdpfx Aszbhh Relwec Type PR6 150 4100 Capacity: 4100 x 150 tons Cybelec DNC 880S Y1, Y2, X, R, Z1, and Z2 axes CNC controlled Includes a set of tools.

Condition: good (used), Year of construction: 1990, Roll compactor, Bergmann – used: Price ex works: only €950 (net) Manufacturer: Bergmann Type: PS 8100E Year of manufacture: 1990 Serial number: 05 3658 2845/90 Pressing pressure: to Weight: 750 kg 400V, 5.5 kW Condition: good Available: from Q4/2026 Cjdpfx Ajzbygrolworc Location: Hamburg Efficient waste compaction: A special steel drum enables effective collection, shredding and compaction of the waste, reducing its volume up to ninefold. Continuous filling: The machine allows for continuous filling by all users. The feed shaft can also remain open during the working process, which facilitates and accelerates waste compaction.

Condition: good (used), Year of construction: 1999, Baling presses, HSM, 30-ton pressing force – used: Price ex works: only €2,950 (net) Manufacturer: HSM Codpfx Aezbygfjlwerc Type: 225.1 VL Year of manufacture: 1999 Machine number: 6124.834. N Serial number: 200014505 Pressing force: 30 tons 400V, 5.5kW Condition: good Available: from Q4/2026 Location: Hamburg

Condition: used, Year of construction: 2013, total length: 3,050 mm, total width: 1,650 mm, total height: 2,350 mm, Colour: Grey Weight: 5.690 kg Price: On request - Year: 2013 - Documentation available: No - CE certificate present: No - Serial number: 7304138524 - Drive system: CNC - Control system brand: Durma - Power [kW]: 7.5 - Number of axes [pcs]: 3: Y1+Y2+X - Press force [ton]: 60 - Max. working width [mm]: 2050 - Column gap [mm]: 1720 - Backgauge depth [mm]: 800 - Crowning system: Mechanical Cedpfx Alszbhy Towerc - Tools included: Yes - Options: Digital readout - Transport dimensions: 3050mm x 1650mm x 2350mm (l x w x h) - Transport weight [kg]: 5690kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum