Used Threaded Bolt for sale (4,136)

Condition: used, CTS T-50/3800/I – Temperature/Battery Test Chamber Temperature range: -50 to +100 °C | 3,750 liters | water-cooled Nitrogen inertization with O2/CO monitoring and safety door locking Used temperature test chamber from CTS – Clima Temperatur Systeme GmbH. According to the previous owner, it was used for HV battery testing; suitable for temperature and material testing, environmental simulation, and quality assurance. Crsdps Ah Si Hjfx Aktoi TECHNICAL DATA Type: T-50/3800/I Temperature range: -50 to +100 °C Temperature deviation over time/space: up to ±0.5 K each Heating: approx. 4 K/min (-40 to +80 °C) Cooling: approx. 3 K/min (+85 to -40 °C) Change rates according to the manufacturer, without test specimen, measured in the supply air. REFRIGERANT Pre-cooling: R507, 6.5 kg Cooling: R23, nameplate rating 15 bar / 5 kg Both circuits: max. permissible overpressure 25 bar, test pressure 27.5 bar ELECTRICAL 400 V / 3/N / 50 Hz; rated power 20.4 kW; rated current 36.3 A On-site protection: 50 A slow-blow; protection class IP54 DIMENSIONS AND WEIGHT Test volume: 3,750 liters Internal dimensions (H × W × D): approx. 1,000 × 2,500 × 1,540 mm according to the previous owner Installation drawing: dimensions in plan view 2,840 mm; system height approx. 2,450 mm. Complete external dimensions to be confirmed. Test chamber approx. 2,700 kg; control cabinet approx. 200 kg; total approx. 2,900 kg without test specimen/additional equipment. EQUIPMENT Digital temperature control with 32-bit controller, LCD setpoint/actual value display, manual and program operation, stainless steel test chamber (1.4301), stainless steel heating element, radial fan, lockable double-leaf door, water-cooled refrigeration unit, separate control cabinet. Test chamber floor load: 500 kg. SAFETY AND CONNECTIONS Nitrogen inertization, O2 residual content and CO monitoring, Dräger-Polytron sensors according to the previous owner, ATEX-tested flame arrestors according to manufacturer’s documents, electromagnetic door locking, mechanical emergency opening, safety temperature limiter, overpressure switch in the refrigeration circuit, fan motor current monitoring. RS232; potential-free fault report contact. HV connections and cooling water connections for test specimens according to the previous owner. Max. heat radiation: 5,000 W at -40 °C. Cooling water: R 1 inch, approx. 2.5 m³/h at ΔT 10 K and full load. Nitrogen: R 3/4 inch, operating pressure 3–6 bar. Condensate drain: R 1 inch internal thread. Sound pressure level: below 70 dB(A) according to the manufacturer. NOTE ON BATTERY TESTING HV battery application and designation of the safety equipment as “Hazard Level 6” according to the previous owner; classification not independently confirmed. CONDITION AND SCOPE OF DELIVERY Used; optical condition according to the pictures. 1 × CTS T-50/3800/I, separate control cabinet and accessories according to the pictures. Shipping or freight forwarding possible. Subject to changes, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Technical details turning diameter 570 mm turning length 1000 mm control MANUALplus 620 swing diameter over face slide 340 mm spindle bore 93 mm spindle turning speed range 1 - 3000 U/min transmission ratio 2 rapid power traverse in X-and Z direction 7 / 10 m/min max. workpiece weight -without tailstock 500 kg max. workpiece weight between centres 1000 kg workpiece weight in steadies max. 1250 kg main drive motor (100/60% ED) 20 / 25 kW Dimensions (LxWxH) 2,94 x 2,20 x 1,96 m max. torque on the spindle ca. 1400 Nm weight of the machine ca. 3,4 t Additional information * HEIDENHAIN MANUALplus 620 control system - Control system expansion for ICP and DIN programs, incl. thread repair * Automatic 8-station SAUTER turret with driven stations, VDI shank D=30 mm, mounted in front of the turning center (limits achievable turning diameter and tailstock operations; reduces turning length) * 2-speed planetary gearbox, automatic shifting * Main spindle holding brake, incl. software upgrade for bolt hole circle and milling cycle options - C-axis-style functionality for pocket milling, with drilling, milling, and engraving cycles and free ICP input * Reinforced coolant pump Cjdpfjz Ixz Djx Aktjri * RÖHM 3-jaw chuck, 315 mm, with one set of hard jaws * Steady rest * Approx. 20 fixed tool holders

Condition: excellent (used), Four-jaw chuck make Röhm Crodpepk A A Hofx Aktsi diameter 315 mm single adjustable jaws bolt circle 120 mm

Condition: used, Year of construction: 2005, 1 used, very well-maintained crankshaft milling attachment for mounting, e.g., on a lathe for milling crankshafts or other milling operations. Manufacturer: SEMA, Origin: Austria Model: SE 100 Year of Manufacture: 2005 Technical Data: Cedpfeddziysx Aktjri Spindle mounting: ISO 50, Runout / Test mandrel L=300 mm = 0.01 mm Speed range, continuously variable: Currently set to 2,000 rpm Spindle is designed for: Up to 3,000 rpm Drive power: Currently 15 kW The milling spindle is designed for: Up to 25 kW Bearing diameter: 110 mm The 2 bolted adapter plates under the milling spindle are each bolted on. These plates can be used for your lathe, modified, or may need to be newly manufactured. Mounting surface of the milling spindle: L x W: 490 x 250 mm Accessories / Special Features: Milling spindle: • The milling spindle is mounted on the flat support of your lathe • Continuously variable speed adjustment, frequency inverter manufacturer LENZE, designed for up to 30 kW • Right / Left rotation • Lifetime-lubricated spindle bearings • Stable construction with hardened and ground spindle • High precision • 2-fold supported spindle with 5 spindle bearings • Workpiece clamping via a threaded spindle • Mobile carriage with control panel • Emergency stop • Lockable main switch Indexing gear for the main spindle: • A long drive rod is mounted in the spindle bore and connected to the gear • Continuously variable speed adjustment, frequency inverter manufacturer LENZE • Right / Left rotation • Jog operation, fast / slow The pictures show this unit mounted on a universal lathe SARO SPA 10 x 3000 for milling crankshafts. This lathe is not included in the scope of supply! Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 D - 44143 Dortmund - Wambel

Condition: used, Technical details: diameter: 250 mm passage: 80 mm width: 80 mm weight of the machine approx.: 23 kg dimension L-W-H: Ø 250 x 130 mm 4 jaw chuck with flange - width of the main body 80mm - with clamping jaws for internal /external - flange size Ø 250 x 18 mm, thread 4 x M16 ; pitch circle of the bolts = Ø 170 mm Other 3- and 4-jaw chucks and face plates in stock. Please inquire! Crjdju Nlfiepfx Aktei *

Condition: used, Year of construction: 1968, functionality: fully functional, machine/vehicle number: M10L/8556, Offer Number: M10L/8556 Machinetype: boltmaker 4 die 4 blow Info: bushing cut-off , PKO Make: NEDSCHROEF Cedpjwi Uc Ssfx Akteri Type: HPT6 Constr. year: 1968 diameter range: 10-24 mm number of dies: 4 number of stations (incl. cut off): 7 cutting length: 200 mm shaft length under head: 160 mm output - pieces/min: 60 max. thread length: 95 mm max. width acros flats: 32 mm press power: 350 to Location: In our warehouse

Condition: used, Year of construction: 1984, functionality: fully functional, machine/vehicle number: M10L/8539, Offer Number: M10L/8539 Machinetype: boltmaker 4 die 4 blow Info: Closed cutter , IFO , PKO , with thread roller and pointer Make: NEDSCHROEF Type: BL4 Constr. year: 1984 diameter range: 6-16 mm number of dies: 4 number of stations: 7 cutting length: 340 mm shaft length under head: 65-300 mm output - pieces/min: 60-90 max. thread length: 65-150 mm Codewi Sxkopfx Aktori press power: 150 to max. width acros flats: 22 mm Location: In our warehouse

Condition: new, Year of construction: 2022, functionality: fully functional, Kunzmann WF 410M tool milling machine with Heidenhain TNC 128 control. Brand new and CE-compliant! Technical specifications: >> Year of manufacture 2022 Machine no. 411555 >> Milling table clamping area 650 x 375 mm Clamping slots 5 Slot width 14 H 7 Slot spacing 63 mm Maximum load 250 kg >> Speed range 1-4500 rpm >> Feed X, Y, Z axes (infinitely variable) up to max. 5/5/4 m/min >> Travels X/Y/Z: 410/350/450 mm >> Vertical quill and horizontal quill - SK40 >> Hydraulic tightening system >> Weight approx. 2000 kg Crodpfx Akev Rppkotei >> Dimensions approx.: 2 x 2 x 2 m >> Connected load 13 kVA Accessories and equipment: >> Heidenhain TNC 128 control >> Heidenhain HR electronic handwheel 510FS >> Vertical and horizontal hydraulic clamping >> Automatic central lubrication >> Spindle brake >> Technical documentation, spare parts plans, operating instructions >> Machine light >> Minimum quantity lubrication >> Counterholder >> Digital display for spindle stroke >> Oriented spindle stop (tapping without compensating chuck) >> Chip protection cabin >> KT 130 edge finder >> Coolant system >> 200 mm rotary table >> Dividing head with 125 mm three- and four-jaw chuck >> 125 mm hydraulic vise About the machine: Offered is a Kunzmann WF 410M tool milling machine, built in 2022, in new condition with a Heidenhain TNC 128 control. The TNC 128 provides numerous dialog-guided cycles with graphic simulation for fast and easy data entry, e.g.: various drilling cycles, thread cutting, bolt circles, hole pattern, rectangular pockets, rectangular tenons, and multi-pass milling of surfaces. A very easy-to-use control system. The machine also has hydraulic clamping for both vertical and horizontal operation. Converting from vertical to horizontal is very easy by folding away the vertical head. The guideways are regularly lubricated by the central lubrication system. The Kunzmann has been mechanically and electrically tested by us. Take advantage of the opportunity to inspect and try out the Kunzmann on site with power on.

Condition: good (used), 4-Application chuck, key bar chuck, three-jaw chuck, three-jaw lathe chuck, power chuck, hydraulic chuck -Power chuck: chuck size Ø 215 mm -Jaw width: 20 mm -Passage: Ø 52 mm -Mounting: Cone Ø 106-103 mm Crjdsv Tvtnjpfx Aktei -Thread: M60 -Bolt circle: Ø 133 mm -Dimensions: Ø 215 x 90 mm -Weight: 19 kg

Condition: good (used), Clamping cylinders, hydraulic clamping cylinders, hydraulic clamps, pneumatic clamps, air cylinders, clamping cylinders for power chucks -Manufacturer: Röhm Gamet, pneumatic clamping cylinder for power chucks -Mounting: Thread M60 -Bolt circle: Ø 88 mm / M8 -Dimensions: see photos -Dimensions: 267/185/H235 mm -Weight: 18.2 kg Credov Twkzepfx Aktsi

Condition: used, mileage: 1 km, first registration: 04/2004, Drive: Wheel Csdpfxeucq Rns Akteri Empty weight: 3.750 kg

Condition: excellent (used), Year of construction: 2005, bore capacity in steel (diameter) 40.0 / 50.0 mm throat 300 mm bore stroke 160 mm threading M 30 in ST turning speeds 70.0 - 4.000 U/min table: 615 x 430 mm bore spindles - Morse Taper 4 Kurzspindel MK column diameter 145 mm feed 0.1-0.2-0.3-0.4 mm/U distance spindle /table 147 / 688 mm T-slots 2 x 14 x 224 mm engine output 1.8 / 2.9 kW weight 450 kg Machine height 1865 mm Csdpfe Afp A Hox Aktsri Current new price approx. 22.000 euros Special price upon request In well-maintained condition (!!) Features: - Robust pillar drilling machine - INDUSTRIAL GRADE - * Drive: V-belt - VARIO (variable speed) - - Automatic spindle feed * With electromagnetic feed clutch * 4 feed rates: 0.1, 0.2, 0.3, 0.4 mm/rev * Feed overload protection - Infinitely variable speed adjustment * Digital speed display - Tapping (thread-cutting) function - Emergency stop button (front-mounted) - Main power switch (front-mounted) - Original operating manual Included special accessories: - Adjustable machine work light - Tapping attachment with footswitch - Automatic drilling depth control * Includes: drilling depth programming, chip-breaking function, . retract/clearance function (adjustable via digital potentiometer) . digital display (including drilling depth readout) - Fine adjustment for drilling depth and fixed stop * Setting increment: 0.1 mm - 4x anti-vibration machine mounts

Condition: new, color: grey, Empty weight: 35.000 kg Dimensions (LxBxH): 360 x 360 x 1250 cm Cargo space capacity: 384.000 l Number of fillers: 2 500 Tonness CAPACITY BOLTED CEMENT SILO TECHNICAL SPECIFICATIONS SILO CAPACITY 500 TONS, 385 m³ (cement density as 1,3 ton/m³) SILO HEIGHT 19.945 mm SILO DIAMETER Ø 6.180 mm QUANTITY OF SILO LEGS 6 SILO OUTPUT DIAMETER Ø 300 mm NUMBER OF COMPONENTS 250 SILO WEIGHT 28.000 kg(Wtih Legs:35000kgs) MATERIAL OF SILO LEGS Ø273 x 12 mm STEEL PIPE SUPPORTS OF SILO LEG NPL 80 mm CORNER IRON SHEET METALS OF SILO LEG 20 mm CONICAL PART SUPPORT MATERIAL 200 mm STEEL C CHANNEL CONICAL PART MATERIAL ST- 37, 8 mm SHEET METAL SILO BODY MATERIAL ST -37, 8 - 6 - 5 mm SHEET METAL SILO TOP COVER MATERIAL ST -37, 6 mm SHEET METAL CHARGING PIPE 4" STEEL PIPE UP TO SILO LEG INNER MANHOLE IS PRESENT OUTER MAN HOLE IS PRESENT Crodsygk Aujpfx Aktji SILO ROOF INCLUDES HANDRAILS MAINTENANCE PLATFORM IS PRESENT STRUCTURAL ANALYSIS IS MADE FOR THE SILOS AND MANUFACTURING PROCESS DEPENDS ON APPROVED PROJECTS. Painting : 1 layer of anticorrosive paint, 2 layers of FINAL COAT EPOXY PAINT , total paint thickness : 140 microns

Condition: new, Year of construction: 2026, Approx. 360 starter bays (more available on request), boltless shelving racks, plug-in system, manufacturer: dalminels, dimensions: 1.30m x 0.60m (other sizes available), frame height: 2.20m (other heights available) – New equipment: Price per starter bay: €119 (net) Price per extension bay: €99 (net) Purchase only by the truckload, otherwise the transport costs may be disproportionately high! Approx. 360 bays fit per truckload (depending on configuration). Manufacturer: dalminels, Italy Model: Errex Year of manufacture: New Finish: Galvanized Frame height: approx. 2.20m (other heights, e.g., 2m available on request) Load capacity per level: 141 kg 5 shelves per bay – additional shelves available at extra cost Shelves approx. 1.30m x 0.60m (shelves consist of 3 panels, each 20cm deep) Csdpfoyhxmnex Aktsri This system features shelves that slot into rails on the sides. Condition: New delivery time: approx. 4 weeks, usually faster – please inquire for current lead times! Location: Delivery included within Germany Other shelf sizes available on request: For example: Widths: 1m and 1.30m Depths: 30cm / 40cm / 50cm / 60cm / 70cm / 80cm Accessories available at extra cost: e.g., drawers, dividers, bracing beams as an alternative to cross braces, etc. Also available as multi-level installations!

Condition: new, maximum load weight: 48,300 kg, overall weight: 71,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available for immediate and short-term delivery, on our website. Extract from the equipment features. Full specification available on request. GOOSENECK: * Gooseneck with integrated 1-axle running gear (pendulum axle) in detachable design * Gooseneck hydraulically liftable and lowerable, including hydraulic coupling connected with the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with a front taper of approx. 60° * Saddle load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Front bulkhead made of steel, detachable, approx. 400 mm high, with chamfered design Crodsyhkqnopfx Aktsi * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside on the front bulkhead of the gooseneck with lifting arm * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings in the outer frame of the front chassis, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings at the transition between chassis and loading platform (LC 10,600 daN) * On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized finish * On the gooseneck, 1 plug-in aluminium tailboard, approx. 400 mm high, anodized finish * 3.5-inch king pin * TPMS tire pressure monitoring system compliant with ECE R 141 * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 1 INOX toolbox with 1 lid, mounted on top of the gooseneck on the right in the direction of travel near the aluminium drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING AREA: * Lowbed with external main beams, designed as a telescopic loading platform in low-profile layout with front extension including a fixed approx. 50 mm hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical pin-lug coupling from the lowbed to the chassis to exchange the platform or install extension beams * 1 locking position every approx. 500 mm in the extension section * 4 pairs of recessed lashing rings arranged lengthwise on the loading area, distributed along the outer frame/main beam (LC 10,000 daN) * 1 lashing ring per side on the outside of the rear crossmember (LC 10,000 daN) * Foldable widening sections, approx. 230 mm per side (WITHOUT timber planks) * Detachable widening planks, steel-edged * Preparation for installation of bolt-on container positioning devices for 1x 20' or 1x 40' container on the main beams. Container locks not included * 6 pairs of threaded blocks between the lashing rings under the upper flange on the main beam for mounting screw-type M24 rings (LC 8,000 daN) * 2 pairs of M24 screw rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed external frame, checker plate decking and continuous prism-shaped excavator recess, approx. 1,450 x 900 x 505 mm, open at rear * Pendulum axle, all axles hydro-mechanically forced steered * Hose burst valve on the axle compensation cylinders with automatic reset function * Hydraulic cylinders with shut-off cocks and pre-insertion facility for securing in raised position * Final paint on axles in 2 coats of 2-pack paint, solid colour DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF. Brand at our discretion * Remote steering from front and rear via cable-control, with axle alig

Condition: used, Stainless steel tank made of V2A, cubic shape - used - Capacity approx. 5,000 liters. Total height approx. 2,650 mm Operating pressure: non-pressurized Inner shell material: V2A (1.4301) Foot material: V2A (1.4301) External surface: marbled finish Equipment Support type: dished feet Number: 4 Attachment: fixed Top bottom: flat bottom Lower bottom: flat bottom Top bottom: • 2 x crane lugs • 1 x lid with folding handle & integrated vent Shell: • 1 x manway 440 x 345 mm with swing bolt • 1 x threaded nozzle DN 25 • 1 x threaded nozzle DN 50 • 1 x sample tap • 1 x visual level indicator Credpfx Akowz Etlstoi • 1 x ladder hook Lower bottom: • 1 x outlet DN 50 extended to the front Otherwise as per photos Available quantity: 16

Condition: new, overall weight: 80,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, More vehicles available. Excerpt from the equipment list below. Crsdsxarmaepfx Aktji Full equipment details on request. GOOSENECK: * Gooseneck in SNT design, optimized for loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * Suitable for tractors: 4 x 2, 6 x 2, and 6 x 4 * Detachable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling all hydraulic functions except hydraulic winches * Gooseneck outer rail with mounting holes for screwable lashing rings. First hole approx. 200 mm from front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at rear part of gooseneck (LC 10,000 daN) * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Approx. 40 mm hardwood floor covering on gooseneck, checker plate covering over kingpin * 3.5-inch kingpin * Gooseneck guide plate for the fifth wheel, approx. 500 mm wide * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) * 2 pairs of lashing rings with retention spring hanging on the outer rails of the gooseneck (LC 5,000 daN) LOADING PLATFORM: * Extendable loading platform, length approx. 8,800 mm with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical lock bolt and reinforced locking positions; supply lines routed securely inside the extendable rails, automatically adapting to the current platform length * BPW axles and suspension; 1st axle steerable, all others force-steered via hydro-mechanics * 1st axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting/lowering valve * 235/75 R 17.5 3PMSF twin tires – brand at our discretion * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B – static test load 50,000 kg * Full-length hardwood floor, interrupted between axles, approx. 50 mm thick (increases slip resistance). – Long slots for removable and repositionable bridging elements * At the front of the platform – 1 movable intermediate table, approx. 300 mm wide, for the large-cross-section sliding tube, with checker plate covering. – Front and rear with long slots for removable and repositionable bridging elements * 1 pair of lashing rings on front cross member (LC 10,000 daN) * 7 pairs of flush-mounted, fold-out lashing rings in the outer frame of the platform (LC 10,000 daN) * Extendable (galvanized) widened sections, approx. 230 mm per side (without wooden planks) * 1 pair of mechanical rear supports * Rear steering operable from front and rear via cable remote control, with single-track control of axles, without installation on the tractor * TPMS tire pressure monitoring sensors fitted to all wheels * Deck locking with conically welded locking profiles every 500 mm * Lock monitoring left and right on the trailer * Mechanical lock for intermediate table (approx. 300 mm wide) to secure the table when extended * 5 pairs of threaded blocks mounted on the extendable rail for the installation of M20 screw-in rings (LC 5,000 daN) BRAKING SYSTEM

Year of construction: 2025, condition: new, New machine Year of manufacture: 2025 Features and technical specifications: Fully equipped in standard version with: - Robust, torsion-free steel frame, welded and bolted construction - Lamella pressure beam TOP with 6 elements, lamella pressure beam SIDE with 5 elements - Lamella pressure beams with proven tolerance compensation system (Ganner system) for tightly compressed carcass joints - Counter-pressure surfaces (side pressure wall, base) are 38 mm thick, coated, continuous support plates - Continuous pressing surface, height 95 mm, on lower vertical pressure beam - Electromechanical adjustment of both pressure beams via precision trapezoidal thread spindles (with increased lead and concentricity accuracy) and high-performance ball nuts with grease reservoir - The pressing process is carried out electromotorically, via 2 independent worm gear motors (2 x 0.75 kW) - Pressing force of the pressure beams is infinitely variable and electronically controlled by 2 potentiometers, regulated via frequency inverter, ensuring absolutely wear-free force control - Pressing force for horizontal pressure beam: min. 500 daN (kg), infinitely adjustable up to max. 2200 daN (kg) - Pressing force for vertical pressure beam: min. 300 daN (kg), infinitely adjustable up to max. 2200 daN (kg) - Pressing and adjustment speed of the beams with fine positioning, using 3-stage selector switch: 5 / 10 / 25 mm/second - Jog mode for precise positioning of both pressure beams, e.g. for low pressing forces, drawers, and carcasses at 45° - Simplest operation via 6 separate push buttons, 8 movement cycles selectable via control panel - Freely adjustable press time preselection 0-30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressure beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 300 mm Cedow Nafkspfx Aktjri - Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm Including surcharge for rapid traverse speed, for fast positioning of the pressure beams, controlled via automatic workpiece detection with sensors in the pressure beams, pressing speeds 5 / 10 / 25 mm/sec and rapid traverse speed 50 mm/sec, the sensors can be deactivated for pressing special components Including a set of machine feet for 500 mm working height Location: Flörsheim Availability: Short-term

Condition: good (used), Year of construction: 1999, functionality: fully functional, total length: 500 mm, total width: 1,060 mm, total height: 1,800 mm, -KOM 3166- Offered here is an SSI Schäfer boltless shelving unit in good condition. The maximum bay load is 1200 kg, and the maximum shelf load is 200 kg. Due to its low height, the rack is ideal for rooms with limited ceiling clearance. Available quantity: 20 units The racking system consists of: - 1x Schäfer storage bin LW 512 - 2x Schäfer storage bins LW 530 - 2x "Standard" shelves Rack dimensions: Height: approx. 1800 mm Depth: approx. 500 mm Width: approx. 1060 mm Height of storage compartments (from bottom to top): 1x lower standard shelf: approx. 250 mm high 2x Schäfer large storage bins: approx. 350 mm high 1x middle standard shelf: approx. 350 mm high 1x Schäfer small storage bin: approx. 200 mm high Crjdpfxexqdy He Aktoi IMPORTANT! The height of the Schäfer storage bins can be adjusted individually using the brackets (see last photos). Additionally, an extra Schäfer storage bin of type LW 530 can be installed on the upper standard shelf with this racking system. This configuration is shown in the last listing images.

Condition: new, STF374KV5051GAS3 FOUR ROW TAPER ROLLER BEARINGS NSK NEW, NEVER USED Main Demensions: 374,65 x 501,65 x 250,83 mm Weight 156 kg 3 units available Crjdpfeqpfvbex Aktei WAREHOUSE LIQUIDATION

Condition: new, R425-1G4S7 NSK TAPERED SINGLE ROW ROLLER BEARINGS NEW, NEVER USED Main Demensions: 425 x 700 x 150 mm Weight 216 kg 2 units available Codpfxeqpf T Is Aktori WAREHOUSE LIQUIDATION

Condition: used, Ball screw with nut, transroll spindle, ball screw nut, threaded spindle, threaded rod, threaded bolt, threaded rod -Manufacturer: NTN -Thread: diameter 32 mm -Pitch: approx. 10 mm Csdef R Iwuspfx Aktori -Thread length: 482 mm -Techn. Drawing: see photos -Dimensions: 672/93/H93 mm -Weight: 9 kg

Condition: good (used), Approx. 24 SSI Schäfer R3000 frames, depth 30cm – used: Cjdpfjki Tz Aox Aktsri Price per piece: only €30 (net), packaged and loaded for transport from our location! Manufacturer: SSI Schäfer Type: R3000 Year of manufacture: unknown Frame height: approx. 2.28m Frame depth: 30cm Condition: good Available: immediately Location: Frankenberg / Saxony

Condition: good (used), Technical data for the pallet racking crossbeam: Racking system: Link 51 Type: Boltless XL Included in the scope of delivery: 01x Pallet racking crossbeam, used Material color: yellow Box profile: 80|53 x 45|25 mm Crossbeam type: 4 BST Step profile: H 28 mm, W 20 mm Clips: 4 HK (hooks) Clear width: 2,700 mm Max. load per pair of crossbeams: 900 kg, with evenly distributed load 02x Securing pins, used Design: fully galvanized For securing the longitudinal beams against unintentional lifting out Further information on the pallet racking crossbeam: Crossbeam type 4 BST is used to insert chipboard, steel panels, or similar materials, which then end up approximately flush with the top edge of the racking crossbeams. This prevents any height loss; furthermore, the front of the step crossbeam protects the floors or the insertion segments from damage. Credpfx Askv Urwsktei The crossbeams are not intended for pallet storage, but rather as picking levels; i.e., for storing boxes, small parts, or similar items.

Condition: good (used), Screws, washers, stainless steel screws, VA screws, wood screws, hanger bolts, solar fasteners Credpfx Aksq Nqxajtoi -Solar fasteners: 1375 fully assembled threaded rods -Type: M10 x 250 SW 7 -Material: Stainless steel A2 -Price/Sale: complete -Transport dimensions: 1200/800/H300 mm -Weight: 235 kg