Used Threaded Bolt for sale (4,062)

Condition: good (used), Technical Data for Pallet Racking System: Racking System: Dexion (Hovik) Type: P 90 Technical Data for Installation: Number of racking rows: 01 pc. Length per racking row: approx. 27,990 mm Number of bays per racking row: 10 pcs. á 2,700 mm Number of levels plus ground level: 03 pcs. Fpsdpfx Ahjw R Ubvo Uep Scope of delivery includes: 11x pallet rack uprights, used Material color: sendzimir galvanized Type: H Profile dimensions: 90 x 70 x 2.50 mm Incl. horizontal and diagonal bracing, base plates Uprights are pre-assembled (bolted framework) 5,000 mm high 1,050 mm deep 60x pallet rack cross beams, used Material color: white Box section: 120 x 50 mm Beam connector: 5 HK Clear span: 2,700 mm 120x safety pins, used Material color: sendzimir galvanized For securing the longitudinal beams against unintentional lifting 44x expansion anchors, new Manufacturer: Hilti Model designation: HST2 M12x105/10 Design: carbon steel, galvanized Approved for: cracked concrete 22x leveling shims, used Design: fully galvanized For leveling rack uprights installed on uneven floors 01x load sign With field and bay load specifications, manufacturer and commission number Dimensions: 420 x 297 x 3 mm Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is only offered for self-collection. Any additional transport or shipping of this item will incur extra costs, which can be requested from us separately depending on place of delivery and scope of supply.

Condition: used, Year of construction: 1998, operating hours: 13,258 h, 1998 | Liebherr L 522 with High-Tipping Bucket | Used Wheel Loader | 13258 hours 📍Location: Germany, Stuttgart 🚛 Delivery available to your destination – Use our shipping calculator to estimate transport costs! 💰 Buy Now for EUR 15000 or Make an Offer. Payment at delivery available for an affordable fee (subject to approval)* 👷‍♂️ Inspected by an independent expert 54 inspection points 53 approved ✅ 1 imperfect ℹ️ 0 issues ⚠️ 📌 Inspector's Comment: Wheel loader Liebherr L522 with high dump bucket. the condition of the machine corresponds to the value of the operating hours. leakage hydraulic oil on one of the two chassis motors. at the time of inspection, the machine ran / functioned without any other abnormalities. the machine shows wear on bolts and bushings corresponding to the age and mileage and the purpose of use, as well as signs of use (dents, abrasions, etc.) and corrosion. the machine has not been tested under load. well maintained and serviced machine. ready for immediate use. Fsdpfsxu Rtbjx Ah Uepp 📄 Want to see the full inspection, extra photos, or a video? Tip: The reference "32949 Equippo" is commonly used when looking up more details online. 💡 Why this machine and our service stands out: ✔ Thorough inspection by professionals ✔ Jobsite delivery available ✔ Money-Back Guaranteed ✔ Secure and flexible payment options 🔄 Considering other equipment options? We offer helpful tools and resources for all equipment owners and operators – easily accessible on our platform.

Condition: excellent (used), functionality: fully functional, Universal milling machine Deckel Maho DMU 50M with line control TNC 124 from Heidenhain TOP condition !!! Technical data: >> Year of construction 1998 >> Heidenhain control TNC 124 >> Traverse paths X500/Y400/Z400 >> C and B axis manual with display >> Speed 20- 4500 1/min >> Feed 5000mm/min >> rapid traverse 5m/min >> Tool holder SK 40 >> Table Ø700x500mm >> swivel range +95° /-10° >> electronic handwheel >> Weight 2800Kg >> Machine dimensions approx. 4.0 m x 2.5 m height 2.6 m >> Coolant device >> Power connection 400V 32A Fpedpfxsr Hbf Te Ah Uep About the machine : We are offering a Deckel Maho DMU 50M universal milling machine with a Heidenhain TNC 124 line control in very good condition. The table is manually (digitally) adjustable by two additional axes B and C. A very easy to operate control, it can enter and approach positions, deep and thread drilling, drilling patterns, hole circles, hole rows and rectangular pocket milling. Programs can be entered and read out via an interface. The Heidenhain line control makes work easier and even more precise. The milling machine was used in a large company for training purposes. Take the opportunity to inspect and try out the machine under power on site.

Condition: new, functionality: fully functional, Year of construction: 2025, container length: 5.6 ft, color: grey, overall weight: 10,000 kg, maximum load weight: 9,216 kg, empty load weight: 784 kg, loading space volume: 7 m³, loading space width: 1,720 mm, loading space length: 3,740 mm, loading space height: 1,500 mm, Price on request. The price applies ex stock 33106 Paderborn! Quantity discounts available for purchase of multiple containers. Leasing/hire purchase possible. 15 units directly in stock, RAL 7043 18 units available at short notice, RAL color of your choice Fpsdjw D A Hhepfx Ah Ujp Other versions and sizes available from stock Paderborn. You are welcome to view our current inventory on our website. Roll-off containers according to DIN 30720 Technical Specifications: • Internal dimensions: 3485 x 1720 x 1500 mm • Usable volume: 7 m³ • Empty weight: 773 kg • Floor: 6 mm S 235 • Sides: 4 mm S 235 • All sheets and profiles fully welded • Container inspected and certified according to DGUV 114-010 • Corner reinforcements • Double-sided triple tipping bearing (bolt Ø45) • Stack bar, L-profile • Safety bar • Frame edge U 80x50x4 • Interior and exterior zinc phosphate primer, exterior • Painted with synthetic resin paint (80-100 μ) • Permissible total weight: 10,000 kg Subject to errors and prior sale. Photos are for illustration purposes only! For further inquiries please send us a message or call us.

Condition: like new (used), Year of construction: 2015, operating hours: 15,000 h, functionality: fully functional, Year of manufacture: 10-2015 Control: OSP P300S Maximum turning diameter: 650 mm Main spindle Drive power: 32/22 kW Max. spindle speed: 3,000 rpm Max. torque: 955 Nm Spindle nose: A2-11 Spindle bore: 112 mm Hollow clamping cylinder SMW-VNK225-95, bore 95 mm Sub spindle Drive power: 26/22 kW Max. spindle speed: 4,000 rpm Max. torque: 420 Nm Fedpfx Aexu Awljh Uepp Spindle nose: A2-8 Bearing inner diameter: 80 mm Solid clamping cylinder SMW SIN-S175 Milling spindle Drive power: 22/18.5 kW Max. spindle speed: 12,000 rpm B-axis: 0.001° HSK-A63 Travel paths X1/X2-axis: 695/235 mm Y-axis: 300 mm Z1/Z2-axis: 1,600/1,524 mm B-axis: -30° to +210° Tool magazine / ATC 80 tool positions Max. tool diameter: 90/130 mm Max. tool length: 400 mm Lower turret 12-position tool turret Turning tool: 25 mm Boring bar: 40 mm Special equipment Software for limiting spindle speed to 3,500 rpm Software for multifunctional tools Software extension kit One Touch IGF-M-D Machining Navi M-g for milling operations Tool breakage detection – Renishaw TRS2 laser Machine-side preparation for high-pressure coolant 70 bar Factory-installed door automation Robot interface (Type “E”) Connection for oil mist extraction Separate coolant filtration system TMF300/980, drum-type swarf filter, clean tank 980L Chip conveyor Standard equipment Lower turret with 12 stations, direct mounting system "radial", with cylindrical roller guide on ZB-axis, sliding guide on XB-axis Collision avoidance system (CAS) in real time 19'' color LCD TFT with 3D color graphics as touch screen Second operating system Windows 7 for operation and open data communication, freely usable for Windows 7 compatible applications Tool monitoring system for service life and breakage+ Tool measuring device Machine management MacMan with integrated BDE Ethernet interface with browser and DNC-T1 for program transmission Prepared for remote diagnostics Harmonic spindle speed oscillation by periodic speed variation Tool height correction in Y-axis for rotating tools Circular thread milling X/Z/Y/B including eccentric milling X/Y/C Hi-Cut Pro high-speed control for rotary tools Coordinate transformation Electronic spindle orientation Dimensions and weight L/W/H: 4,480/3,082/3,030 mm, Weight: 18,000 kg

Condition: good (used), Year of construction: 1981, Dimensions (L/W/H) 660x1050x1600 mm metric thread M 33 Messing metric thread M 16 Gußeisen metric thread M 14 Stahl no. of flutes 25x10mm 2x T-Nuten Fpjdpfxsul Eg Dj Ah Ujp throat 220 mm weight 730 kg

Condition: good (used), Technical specifications of the pallet racking system: Racking system: SSI Schäfer Model: PR600 Technical installation data: Number of rack rows: 01 pcs. Length per rack row: approx. 18,450 mm Number of bays per rack row: 05 pcs. at 3,600 mm each Number of levels plus ground level: 02 pcs. Volume specifications: Pallet positions per bay: 05 pcs. Pallet positions per rack row: 60 pcs. Total pallet positions: 60 pcs. Based on: Fedpfx Ahjw Db Ido Uspp Pallet type: Euro pallet EN 13698-1 Dimensions: 1,200 x 800 x 150 mm Total height incl. pallet: n.a. Max. weight per pallet: 900 kg Scope of delivery includes: 06x pallet rack uprights, used Material finish: Sendzimir galvanized Frame type: P73 Profile dimensions: 75 x 75 x 2.0 mm Including cross and diagonal braces, base plates The uprights are pre-assembled (bolted lattice design) Height: 3,600 mm Depth: 1,100 mm 20x pallet rack beams, used Material finish: RAL 5010 gentian blue INP profile: 120 x 58 mm Beam type: TRV1-360-12-l Connector: 4 HK (hooks) Clear span: approx. 3,600 mm Max. load per pair of beams: 3,600 kg (with evenly distributed load) (Note field load limits) 40x safety pins, used Material finish: Sendzimir galvanized For securing the cross beams against accidental lifting 24x anchor bolts, new Manufacturer: Hilti Model: HST2 M12x105/10 Material: Carbon steel, galvanized Approved for: cracked concrete 12x leveling plates, used Finish: fully galvanized For leveling uprights installed on uneven floors 01x load sign Including details for field and shelf loads, manufacturer, and commission number Dimensions: 420 x 297 x 3 mm General information about the item: This item is offered for collection only. Transport or shipping of this item is subject to additional charges, which can be provided upon request depending on the delivery location and delivery scope.

Condition: used, Table Drilling and Thread Cutting Machine IXION Type BT 15 GL Machine no.: Year of manufacture approx. 1975 Drilling capacity: 15 mm Spindle mount: Taper B 16 Thread cutting range: M 2.5 to M10 Throat depth: 200 mm Quill stroke: 90 mm Table size: 285 x 220 mm Column diameter: Ø 75 mm Spindle speed: 320–1600 rpm, 4 steps Motor power: 0.55 kW Power connection: 380 Volt, 50 Hz - Spindle speed adjustable in 4 belt stages - Equipped with FAHRION GH 10 tapping attachment - With thread pitch guide bush, operation without guide bush also possible - Drill head height adjustment via hand crank - Column lowers from table plate for drill head height adjustment Fjdpfx Ahswk Nxqo Uopp Required space (L x W x H): 650 x 420 x 900 mm Weight: 86 kg Good condition

Condition: excellent (used), functionality: fully functional, Universal milling machine Deckel Maho DMU 50M with line control TNC 124 from Heidenhain TOP condition !!! Technical data: >> Year of construction 1998 >> Heidenhain control TNC 124 >> Traverse paths X500/Y400/Z400 >> C and B axis manual with display >> Speed 20- 4500 1/min >> Feed 5000mm/min >> rapid traverse 5m/min >> Tool holder SK 40 >> Table Ø700x500mm >> swivel range +95° /-10° >> electronic handwheel >> Weight 2800Kg >> Machine dimensions approx. 4.0 m x 2.5 m height 2.6 m >> Coolant device >> Power connection 400V 32A Fedpfx Aer Hbf Ejh Ujpp About the machine : We are offering a Deckel Maho DMU 50M universal milling machine with a Heidenhain TNC 124 line control in very good condition. The table is manually (digitally) adjustable by two additional axes B and C. A very easy to operate control, it can enter and approach positions, deep and thread drilling, drilling patterns, hole circles, hole rows and rectangular pocket milling. Programs can be entered and read out via an interface. The Heidenhain line control makes work easier and even more precise. The milling machine was used in a large company for training purposes. Take the opportunity to inspect and try out the machine under power on site.

Condition: good (used), Technical Data for Pallet Rack System: Racking System: Jung Heinrich Type: Esmena Installation Data: Number of rack rows: 1 unit Length per rack row: 33,450 mm Number of bays per rack row: 12 units Number of levels (plus floor level): 2 units Volume Data: Pallet spaces per bay: 9 units Number of pallet spaces per row: 108 units Total number of pallet spaces: 108 units Based on: Load carrier: Euro pallet EN 13698-1 Dimensions: 1,200 x 800 x 150 mm Total height including pallet: n.s. Max. weight per pallet: approx. 800 kg Scope of delivery includes: 13x pallet rack frames, used Material colour: blue Frame profile: MX610 Profile dimensions: 76.2 x 63.2 x 1.8 mm Including horizontal and diagonal braces, base plates Frames are pre-assembled (bolted truss construction) Height: 2,100 mm Depth: 1,050 mm 48x pallet rack beams, used Material colour: yellow Box profile: 140 x 40 mm Beam type: N140x40 SEG Connector: 5 hooks Clear span: 2,705 mm Max. load per pair of beams: 2,400 kg with evenly distributed load 96x locking pins, used Material finish: Sendzimir galvanized For securing the beams against unintentional lifting Fsdjwk I N Uepfx Ah Uspp 52x wedge anchors, new Manufacturer: Hilti Model designation: HST2 M12x105/10 Version: Carbon steel, galvanized Approved for: cracked concrete 26x leveling plates, used Finish: fully galvanized For leveling frames installed on uneven floors 1x load capacity sign With details of bay and compartment loads, manufacturer, and order number Dimensions: 420 x 297 x 3 mm Your contact persons in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information on this item: This item is available for collection only. Any transport or shipping beyond this must be requested separately and will incur additional costs, which depend on delivery location and scope of delivery and can be requested from us.

Condition: used, CNC cycle controlled lathe HARRISON type Alpha 400 Plus Machine No. P30180/150 Year of construction 1998 center distance 1250 mm turning diameter over bed 400 mm center height 200 mm Swing diameter over cross slide 245 mm Swing diameter in the bend 585 mm bed width 313 mm face travel (X-axis) 250 mm Tailstock spindle diameter 73 mm Tailstock quill stroke 140 mm Tailstock quill mount MK 5 spindle bore 54 mm spindle head size Camlock D1 size 6 Spindle speed 20-2500 rpm. Spindle speed range (stage 1) 15-275 rpm. Spindle speed range (stage 2) 35-795 rpm. Spindle speed range (level 3) 110-2500 rpm. Feed rate X and Z 0.03 - 0.6 mm/rev. Rapid traverse speed X axis max. 2000 mm/min. Rapid traverse speed Z-axis max. 4000 mm/min. Threading function Metric / Inch / Diametral / Module Fjdpfx Aoh Hvk Ash Uspp Spindle drive power 7.5 KW Mains connection 400 Volt, 50 Hz, 23,5 kVA - cycle control Harrison Alpha / GE FANUC - language in French (France) - automatic gear range shifting in 3 steps (15-275, 35-795, 110-2500 rpm.) - electronic handwheels with different transmission ratios (1/10/100) - 3-jaw face spiral lathe chuck FORKARDT Ø 250 mm type CSN, 1 set of soft top jaws - quick-change tool holder MULTIFIX size B with 2 inserts - 1 piece of centering point running with the tool - 1 piece quick-action drill chuck RÖHM, 3-16 mm - hinged lathe chuck guard - hinged working area protection doors - chip tray with coolant device under the machine bed - Switch cabinet fixed to the machine - Interface RS 232 Space requirement L x W x H 2600 x 1450 x 1550 mm weight 1950 kg good condition

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and pull spindle lathe with 2 axis digital readout Heidenhain from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 Fpodpfou Afqlsx Ah Uep >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 2-axis digital readout from Heidenhain >> 1 new three-jaw chuck 125 mm with 2 sets of jaws >> collet chuck device new with collets new from 3 mm to 25 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Back plate To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and feed screw lathe from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: Fpsdpou Aftgjfx Ah Usp >> 1 piece three-jaw chuck 160mm with 1 set of jaws >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1 mm to 20 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Fence >> Change wheels To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Technical data: >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: Fpsdpfx Ahovtp Ede Uep >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection About the machine: A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus GS guide and feed spindle lathe in very good original condition! Technical specifications: >> Year of manufacture approx. 1992 Machine no. 4549 >> Center height 120 mm Fpedpfx Ahewkh Abe Uop >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle bore 23 mm >> Short taper spindle head DIN 4 >> Tailstock MT 2 >> Feed rates from 0.03 to 0.15 mm/rev >> Possible thread sizes: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> New collet chuck system, new collets from 3 to 25 mm >> 1 piece Three-jaw chuck with 2 sets of jaws >> Mulifix size A with 2 tool holders About the machine: Offered is a Weiler Primus GS guide and feed spindle lathe in very good original condition. The machine is fully functional. All slides run very smoothly and evenly. The bed guides are in excellent condition. The Weiler runs very quietly even at high speeds. The Primus was used in a training facility. This newer generation of Weiler lathes is very user-friendly and can produce surfaces that look as if they were ground. Take advantage of the opportunity to view this machine on-site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus GS lead and feed screw lathe 3 axis digital readout Easson- ES8 from training workshop Super condition !!! Fsdpfx Aevkfhpjh Uepp Technical data: >> Year of construction approx. 1990 Machine no. 3768 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 3-axis digital display from Easson ES8 >> collet chuck device from 1 to 20 mm collets 1 mm rising with holder and draw tube >> 1 three-jaw chuck with 2 sets of jaws >> 1 four-jaw chuck with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Bed stop >> Turning device To the machine : We are offering a Weiler Primus lathe built around 1990 in excellent condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The bed guides are in very good condition. The Weiler runs smoothly even at high speeds. The machine comes from a training workshop of a large company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself. Fsdpfxsvivmye Ah Ujpp

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, Weiler precision lathe model Condor B, lead and feed screw lathe with brand new K&C 3-axis digital readout, CE compliant! Technical data: >> Machine No. 2442, year of manufacture 1997 >> Centre height: 165 mm >> Centre distance: 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore: 40 mm >> Camlock spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Thread cutting: metric, imperial, module and diametral pitch threads possible >> Metric thread pitches: 0.18 to 28 mm >> Weight: approx. 1100 kg >> Spindle brake, selectable >> Length: 1.83 m, height: 1.29 m, depth: 0.88 m Equipment and features: >> New K&C 3-axis digital readout, 12-month manufacturer's warranty, supplied with operating manual Features: mm/inch switching, selectable ABS/INC coordinates, value halving function, reference mark, tool memory for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 x brand new 160 mm 3-jaw chuck with 2 sets of jaws >> 1 x 200 mm 4-jaw chuck with 1 set of jaws >> New collet chuck system and new collets from 3 to 25 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear splash guard >> Machine feet Safety features: electronic spindle guard, 2 emergency stop buttons, changewheel box with safety interlock, spindle brake About the machine: Offered here is a Weiler Condor in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new K&C 3-axis digital readout makes work easier and more precise. The machine has been electrically and mechanically checked by us. A complete oil change has been carried out. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to inspect and test this machine under power on site. Fpsdpjxcuazsfx Ah Ujp

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Weiler Primus VC Precision Centre Lathe 3-axis Digital Readout K&C NEW with VC Drive, Stepless Speed Adjustment, and CE Compliance, Very Good Condition Fjdpfx Ahjw Idllo Ujpp Technical Data: >> Year of manufacture: 2003, Machine No. 646 >> Centre height: 140 mm >> Centre distance: 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock Morse taper 3 >> Feeds: from 0.02 to 0.63 mm/rev >> Thread types: Metric, Inch, Module, and Diametral Pitch >> Metric thread pitches: from 0.25 to 8 mm >> Weight: approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and Equipment: >> 3-axis Digital Readout K&C NEW >> Collet chuck system with collets from 3 to 26 mm, new, 1 mm increments, NEW >> 160 mm 3-jaw chuck with 2 sets of jaws >> Multifix size A with 2 toolholders >> Electric chip guard >> Machine feet >> Splash guard About the Machine: This offer is for a Weiler Primus VC lead and feed screw lathe, built in 2003 and in very good original condition. A very nice lathe with VC drive and stepless spindle speed control. The digital readout and scales from K&C are new. This newer generation of Weiler lathes is very user-friendly and can produce ground-like surface finishes. The K&C digital readout makes operation even easier and more precise. Take the opportunity to inspect this machine under power on site and be convinced of its condition.

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Weiler Precision Lathe Model Condor 81 Lead and Feed Spindle Lathe with 3-Axis Digital Display from K&C NEW Technical Data: >> Year of manufacture 1987 Machine No. 87 835 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: Metric, Inch, Module, and Diametral-Pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis digital display from K&C new, 12 months manufacturer's warranty with operating manual Functions: Switch mm/inch, coordinate selection ABS/INC, halving of display value, reference mark, tool programming 200 pcs, taper calculation, radius/diameter, quick zeroing, reversing of count direction >> 1 piece 3-jaw chuck 160 mm NEW, 2 sets of jaws >> 1 piece 4-jaw chuck 160 mm, 1 set of jaws >> Collet equipment and new collets from 3 to 26 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear panel Fpodjwrmuxspfx Ah Uep >> Coolant system >> Machine feet About the Machine: A used Weiler Condor 81 in very good condition is offered. The machine is, of course, fully functional and has been completely disassembled and repainted. A very robust and powerful machine. The new 3-axis digital display from K&C makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was carried out. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine on site under power.

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, Weiler Center Lathe Model Condor B Guide & Feed Shaft Lathe with 3-Axis Digital Readout by K&C NEW from Training Workshop!! Technical Data: >> Machine No. 91-1814, Year of manufacture: 1991 >> Center height: 165 mm >> Distance between centers: 750 mm >> Spindle speeds: from 22 to 2,800 rpm >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet locking >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Threads possible: Metric, Imperial, Module, and Diametral Pitch >> Metric thread leads: from 0.18 to 28 mm >> Weight: approx. 1,100 kg >> Spindle brake switchable >> Dimensions (L x H x D): 1.83 m x 1.29 m x 0.88 m Scope of Delivery and Features: >> NEW 3-axis digital readout from K&C, 12-month manufacturer's warranty with operating manual Functions: mm/inch switch, ABS/INC coordinate selection, display value halving, reference mark, tool programming for 200 items, taper calculation, radius/diameter display, quick zeroing, counting direction reversal >> 1 pc. NEW 160 mm 3-jaw chuck, 2 sets of jaws Fodpow Nw Dqefx Ah Uopp >> 1 pc. 160 mm 4-jaw chuck, 1 set of jaws >> NEW collet chuck and NEW collets from 2 to 24 mm, incremented by 1 mm >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle safety guard >> Rear splash guard >> Fixed steady rest >> Machine feet Safety features: electronic spindle guard, 2 emergency stop switches, change gear cover with limit switch, spindle brake About the machine: We are offering a Weiler Condor in very good condition. The machine is, of course, fully operational. It is a very robust and powerful lathe. The brand new 3-axis digital readout from K&C makes operation even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change has been performed. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine under power at our premises.

Condition: excellent (used), Year of construction: 1983, functionality: fully functional, Weiler Center Lathe Model Condor 81 Lead and Feed Lathe with 3-Axis Digital Readout from K&C NEW Technical Specifications: >> Year of Manufacture 1983 Machine No. 83-067 >> Center height 165 mm >> Center width 750 mm >> Spindle speeds: from 22 to 2800 rpm Fpedpfxowb Supe Ah Uop >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MT 3 >> Feed rates from 0.015 to 0.46 mm/rev >> Possible threads: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake can be switched on >> Length 1.83 m, height 1.29 m, depth 0.88 m Accessories and Equipment: >> New 3-axis digital readout from K&C, 12-month manufacturer's warranty with operating instructions Functions: mm/inch switching, ABS/INC coordinate selection, halving of the display value, reference mark, 200 tool programming, cone calculation, radius/diameter, quick zeroing, counting direction switching >> 1 new three-jaw chuck, 160 mm, 2 sets of jaws >> New collet chuck and new collets from 3 to 26 mm, 1 mm increments >> Multifix size B with 3 tool holders >> Electronic spindle protection >> Rear panel >> Coolant system >> Machine feet About the machine: Offered is a used Weiler Condor 81 in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new 3-axis digital readout from K&C makes work even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was also performed. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to view and try out this machine live on-site.

Condition: excellent (used), functionality: fully functional, Weiler Centre Lathe Model Condor 81 Lead and Feed Screw Lathe with 3-Axis Heidenhain Digital Readout Technical Data: >> Year of manufacture: 1988 Machine No. 88-955 Fpsdoxu Hlaspfx Ah Ujp >> Centre height: 165 mm >> Centre distance: 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 Size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Thread cutting capability: metric, imperial, module, and diametral pitch >> Metric thread pitches: from 0.18 to 28 mm >> Weight: approx. 1100 kg >> Spindle brake can be engaged >> Dimensions: Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis Heidenhain digital readout >> 1 pc. new 3-jaw chuck with 2 sets of jaws >> Collet chuck set, collets from 3 to 30 mm, 40 collets, some duplicate sizes >> Multifix size B with 3 tool holders >> Bed stop >> Machine feet >> Drill chuck >> Live centre For Safety: >> Cover for lead and feed screw >> 2 emergency stop buttons >> Spindle brake About the machine: A used Weiler Condor 81 lathe from 1988 is being offered in very good condition. The machine is of course fully functional. The lead and feed screws are covered for safety. A very robust and powerful machine. The 3-axis Heidenhain digital readout makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A full oil change has been carried out. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to inspect and test this machine under power at our facility.

Condition: excellent (used), functionality: fully functional, Universal Milling Machine Mikron WF 3S with 3-Axis Active Digital Display Heidenhain TNC 114 and Infinitely Variable Feed Technical Data: >> Year of manufacture: approx. 1990 >> Fixed angle table, clamping surface 800 x 450 mm >> Spindle speed: 50 - 2240 rpm Fsdpfjxu Hkcjx Ah Uspp >> Infinitely variable feed on 3 axes from 1 to 750 mm/min >> Rapid traverse on 3 axes: 1400 mm/min >> Travel X/Y/Z: 500/500/380 mm >> Vertical quill - SK40, extendable >> Weight: approx. 1600 kg Accessories and Equipment: >> 3-axis active digital readout Heidenhain TNC 114 >> Central lubrication >> Operating manual, programming manual, electrical diagrams About the machine: For sale is a used Mikron WF 3S universal milling machine. It is equipped with a Heidenhain path control system TNC 114, which means it can travel a programmed distance in any one axis (X, Y, or Z) and stop automatically upon reaching the set value. Up to 4 different zero points can be set, and dimensions can be entered as either absolute values or incremental (chain) dimensions. The feed is infinitely variable from 0 to 750 mm and can be adjusted during machining. Rapid traverse can be activated at the push of a button. Spindle speed is step-adjustable from 50 rpm to 2240 rpm, but only when the machine is at standstill. The vertical milling head is mounted with three bolts, allowing for removal or reattachment in just 2 minutes; it is manually fixed using the articulated arm on the left of the machine and simply swung aside. A particular feature of this machine is its large travel distances relative to its size: Z = 380 mm, X = 500 mm, and Y = 500 mm. Additionally, the machine has electronic overload protection for the vertical spindle. Mechanically and electrically tested. You are welcome to view and test the machine under power at our facility.

Condition: excellent (used), Year of construction: 2002, functionality: fully functional, Universal tool grinding machine Michael Deckel S11 speed, year of manufacture 2002, in very good condition!! Technical Data: >> Year of manufacture: 2002 >> Serial No.: 2197 Clamping range: >> Clamping surface of tool slide 500 x 180 mm >> Max. tool diameter between centers 130 mm >> Max. tool length between centers 270 mm >> T-slots machine stand 12 mm Movement range: >> Working travel Grinding stroke 190 mm Grinding stroke during thread grinding 190 mm Transversal adjustment tool slide 100 mm Vertical adjustment grinding head 325 mm Longitudinal adjustment grinding spindle 5 mm >> Coarse adjustment travel Tool holder 220 mm Grinding head carrier 800 mm >> Swivel angle Grinding head carrier 360 degrees Grinding head 360 degrees Tool holder 360 degrees Grinding spindle: Three-phase drive motor 1.1 KW at 2800 rpm Spindle speeds, stepless 2000 to 12000 rpm Max. grinding wheel diameter 125 mm Max. cutting wheel diameter 200 mm Dimensions: Weight 520 kg Dimensions (D x W x H) 800 x 1100 x 1760 mm Space requirement (including operation) 2.5 x 2.3 m Accessories and equipment: >> See pictures About the machine: Offered is a universal tool grinding machine of the brand Michael Deckel S11 speed. The machine is suitable for grinding high-precision parts. With the S11, individual parts and small batches can be ground amazingly fast, economically, and flexibly, with the highest operating comfort. The Deckel S11speed is in very good condition. Mechanically and electrically tested. Take the opportunity to visit and test this machine on site under power. Fjdswrnf Ejpfx Ah Uopp