Used Wmw Bs 25 for sale (451)

Condition: used, bore capacity in steel (diameter) 40 mm continious capacity 25 mm throat 315 mm bore stroke 200 mm bore depth 280 mm Dkodpfsx Iwgkox Afnsh spindle taper MT 4 feed range 0,1-1,5 U/min column diameter ca. 230 mm number of feeds 9 table-size 700 x 600 mm surface area 450 x 560 mm distance spindle/base plate 1100 mm dimensions ca. 1000 x 700 x 2400 mm total power requirement 2,6 kW weight of the machine ca. 1,1 t emergency stop switch renewed

Condition: used, Year of construction: 1962, frequency 50 Hz voltage 380 V 220 V connected load 2,6 kVA Dkjdpfx Ajrxg S Tofneh rated current 6,1 A weight of the machine ca. 1 t

Condition: used, Technical details: pressure: 25 t distance between columns: 360 mm stroke: 500 mm daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm ram speed - forward: 0,200 m/s ram speed - reverse: 0,45 m/s Table dimensions: 630 x 500 x 71 mm passage inside table: Ø 182 mm surface area of ram: 450 x 360 mm mortise hole in ram: Ø 32 x 72 mm Dedpfx Aeu U D I Rofnekh ram diameter: Ø 125 mm height over floor: 710 mm total power requirement: 12,5 kW weight of the machine ca.: 2,4 t dimension machine xH: 1,7 x 1,1 x 2,95 m Operation via two-hand control panel (and one-hand operation in set-up mode) Continuous and single stroke TÜV until *

Condition: used, Technical details: pressure: 25 t stroke: 500 mm daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm ram speed - forward: 0,100 m/s Dedpfx Afsvc Awxenekh ram speed - reverse: 0,45 m/s Table dimensions: 630 x 500 x 75 mm passage inside table: Ø 180 mm surface area of ram: 450 x 360 mm mortise hole in ram: Ø 32 mm height over floor: 710 mm total power requirement: 8,75 kW weight of the machine ca.: 2,2 t dimension machine xH: 1,7 x 1,1 x 2,95 m Operation via two-hand control panel. (and one-hand operation) *

Condition: good (used), Clamping cylinder, hydraulic clamping cylinder, hydraulic clamp, pneumatic clamp, air cylinder, clamping cylinder for power chuck, hydraulic cylinder -Manufacturer: WMW, clamping cylinder stroke 15 mm -Type: 25 30-7312 -Shaft Ø 14 mm -Number: 12x clamping cylinders available -Price: per piece -Dimensions: Ø 50 x 96 mm Dsdowziikjpfx Afnskh -Weight: 1.2 kg/piece

Condition: used, Technical details: bore capacity in steel (diameter): 22 mm throat: 205 mm bore stroke: 100 mm Dsdsvxf Iropfx Afnjkh spindle taper MT: MK2 spindle speed:: 2 step U/min feed: manuell mm/U Distance spindle/table max.: 150 - 600 mm base plate surface area: 350 x 400 mm table clamping surface:: 360 x 280 mm table rotating: 360 ° drill table adjustment: 450 mit Kurbel mm column diameter: Ø 100 mm control voltage: 380 V total power requirement: 0,8 kW weight of the machine ca.: 270 kg dimension machine xH: 0,6 x 0,5 x 1,95 m column drill incl. machine + vice. *

Condition: used, Technical details: Dodpfxou S H Sts Afnekh width: 625 mm depth: 520 mm height: 820 mm weight of the machine ca.: 300 pro Stück kg 2 pieces available (price per piece) without T-slots Oblong hole Ø 33 x 330 mm *

Condition: used, Year of construction: 1971, Technical details: bore capacity in steel (diameter): 16 mm throat: 250 mm bore stroke: 125 mm Dkedpeu Idhmsfx Afnjh spindle taper MT: MK 2 spindle speed:: 350 - 2000 / 8step U/min table clamping surface:: 280 x 355 mm table rotating: ja ° drill table adjustment: 520 vertical mm distance table - lower edge spindle: max. 600 mm column diameter: 110 mm total power requirement: 1,1 kW weight of the machine ca.: 272 kg dimension machine xH: 0,6 x 0,5 x 1,8 m Equipment: -Drill chuck 13 mm -twist drill 10 mm with 45° countersunk cut -machine vice *

Condition: used, Recently arrived WMW UPW 25 Dedpeygm E Eefx Afnekh

Condition: used, Recently arrived WMW UPW 25 Djdpfx Aoygm Igjfnjkh

Condition: used, Recently arrived WMW UPW 25 Dkjdpfx Ajygm Hvjfneh

Condition: used, Recently arrived WMW UPW 25 Dkjdsygm Efjpfx Afnsh

Condition: good (used), Clamping cylinders, hydraulic clamping cylinders, hydraulic clamps, pneumatic clamps, air cylinders, clamping cylinders for power chucks, hydraulic cylinders -Manufacturer: WMW, clamping cylinder stroke 20 mm -Type: 25 TGL 30-7311 -Shaft Ø 14 mm -Number: 16x clamping cylinders available -Price: per piece -Dimensions: Ø 35 x 127 mm -Weight: 0.6 kg/pc. Dkjdewzillspfx Afnoh

Condition: good (used), Machine number: 26798 Dsdpfeiypmxsx Afnjkh TyP / Model: BS 40 AIII drilling capacity steel / cast iron: 50 / 60 mm spindle mounting: MK 5 Speeds: 32 to 1,400 rpm Feed rate: 0.11 to 1.73 mm/rev table: 780 x 650 mm clamping surface: 630 x 500 mm head height adjustment: 250 mm stroke: 280 mm footprint: 700 x 1.200 mm total power supply: 6,7 kW accessories/equipment: thread cutting function, right-left run; autom. feed, separate control cabinet condition: good weight: 1,5 t dimensions: 780 x 1.200 x 2.700 mm

Condition: good (used), Year of construction: 1963, 3 different eccentric presses, manuf. WMW Dksdpfomi Rpijx Afneh 1 x crank press with one ram 16 t 1 x crank press with one ram 25 t

Condition: excellent (used), Year of construction: 1977, functionality: fully functional, total height: 27,500 mm, total width: 10,500 mm, total length: 16,500 mm, pressing force: 25 t, table width: 630 mm, table length: 500 mm, operating speed: 200 mm/s, overall weight: 2,400 kg, reverse speed: 450 mm/s, ram plate width: 450 mm, ram plate length: 360 mm, distance between stands: 800 mm, stroke length: 500 mm, power: 12.5 kW (17.00 HP), PYE 25 SS hydraulic press. Year of manufacture 1977. manufacturer VEB Wema Zeulenroda (Germany). Parameters: Maximum pressing force 25 tons. Working pressure 16 MPa. Upper table 450 x 360 mm. Dedotzxvwspfx Afnskh Lower table 630 x 500 mm. Ground clearance 800 mm. Cylinder stroke 500 mm. Down speed 200 mm/sec. Upward speed 450 mm/sec. Power requirement 12,5 kW. Weight 2400kg. Height 2750mm, length 1650mm, width 1050mm. Technical condition of the machine very good. The machine after a general overhaul. It is possible to make a visual inspection and check the machine in motion.

Condition: used, Technical details: Dkodpfjvbh N Rox Afneh turning length: 630 mm swing diameter over slide rest: Hinterdrehschlitten: 250 mm center height over bed: 270 mm centre distance: 900 mm spindle bore: 26 mm range of revolutions per minute - continous: 1,8 - 450 U/min return movement speed: 23 / 32 / 46 / 370 / 510 / 740 U/min cross feed: 0,07 - 1,11 / 36 step mm/U longitudinal feeds:: 0,063 - 0,63 / 12 step mm/U tailstock quill taper MT: 5 quill travel: 250 mm Total power requirement: 7,0 kW machine weight approx.: 3,9 t dimension machine xH: 3,2 x 1,2 x 1,8 m Application: Mainly for relief turning and relief grinding of cutting tools (especially hobs with and without thread pitch). Back turning and relief grinding is possible from the front, the back and in the axial direction of the machine. Main drive via 8-stage manual gearbox. Feed gearbox is designed as a 12-stage manual gearbox. Swiveling range of the rear slide = 360deg. Swiveling range of the cross slide = 360degrees Equipment: lathe chuck driving disc Ø 210 mm with fixed tip fixed tip in tailstock with 4 pieces machine feet 3 jaw chuck Ø 250 mm i.D. *

Condition: used, Year of construction: 1979, Technical details: turning diameter over bed: 540 mm turning length: 630 mm centre distance: 900 mm center height over bed: 270 mm center height: über Hinterschlitten: 138 mm Turning diameter: über Hinterschlitten: 250 mm longitudinal feed: 700 mm facing movement : 80 / 75 mm revolution per minute: 1,8 - 450 bei 8x steples U/min clamping diameter: 26 mm range of feed in x - axis: 12 step / 0,063 - 0,63 mm/U range of feed in y - axis: 36 step / 0,070 - 1,11 mm/U tailstock quill: MK5 mm tailstock quill stroke: 250 mm Total power requirement: 7,0 kW machine weight approx.: 3,76 t Dksdpovbhv Rjfx Afneh dimension machine xH: 3,2 x 1,2 x 1,8 m Application: Mainly for relief turning and relief grinding of cutting tools (especially hobs with and without thread pitch). Back turning and relief grinding is possible from the front, the rear and in the axial direction of the machine. Main drive via 8-stage manual gearbox. Feed gearbox is designed as a 12-stage manual gearbox. Swivel range of the rear slide = 360deg. Swivel range of cross slide = 360deg. Lathe chuck is cone disc Ø 200mm with MK5 Equipment: turning mandrel Ø 49,5 x 400mm Measuring system ARBAH-L 3+1 Inverter FRENIC 5000G11 i.D. *

Condition: used, Technical details: grinding length: 300 mm grinding spindle - swivable: 350 ° grinding head adjustable: senkrecht: 250 mm adjustment of spindle-head: quer: 230 mm grinding head adjustable: neigbar +/-15° ° grinding diameter: Ø 250 mm spindle revolutions per minute : 2200 - 3500 - 5200 U/min work table:: B:120 x L: 950 mm table movement: Obertisch schräg: recht/links 45° mm table movement: größter Tischweg: 500 manuell mm surface of magnetic-table: 305 x 130 x 100 mm dimensions of grinding wheel: Topfscheibe 125 x 20 Ø 32mm mm total power requirement: 1,8 kW weight of the machine ca.: 1,0 t dimension machine xH: 1,6 x 1,3 x 1,7 m Djdpfxju Ng Nps Afnokh dimensions of hydaulic: 600 x 550 x 870 mm Accessories: Universal clamping head cone MK5 Drill grinding holder Ø 10mm *

Condition: used, Year of construction: 1970, taper MK 4 Dkedpexzu Dqefx Afnoh feeds: ja weight of the machine ca. 1,5 t

Condition: good (used), Year of construction: 1969, number of straightening rollers: 7, working width: 2,500 mm, sheet thickness (max.): 39 mm, max. sheet width: 2500 mm Dkodpfx Ajyg Inzefnsh Convexity length of rollers: 2700 mm max. sheet thickness (St 50): 32 mm max. sheet thickness (St 34): 39 mm min. sheet thickness (St 50): 8 mm number of straightening rollers: 7 rollers number of driven straightening rollers: 5 rollers diameter of straightening rollers: 290 mm diameter of input/output straightening rollers: 345 mm number of support rollers: 13 diameter of support rollers: 288 mm stroke of upper beam: 120 mm Straightening speed: 16 m / min Rated power of main drive: 90 kW Total load: 138 kW

Condition: good (used), Year of construction: 1994, throat depth: 360 mm, table width: 630 mm, table length: 1,250 mm, Pressure: 250 t Throat depth: 360 mm Table size: 1250 x 630 mm Table diameter: 250 mm Dkodpfx Aeyg E T Ijfnoh Ram clamping surface: 850 x 450 mm Installation height: 800 mm Piston stroke: up to 500 mm Piston diameter: 400/360 mm Ram speed downward: 200 mm/sec Ram speed upward: 110 mm/sec Total power requirement: 20.5 kW Machine weight approx.: 8 t

Condition: good (used), WMW BR 40/2 x 1250 radial drilling machine Drilling capacity in steel (diameter): 60 mm Arm reach: 1250 mm Dkodpfxox U Ecte Afnsh Max. workpiece height: 820 mm Spindle speed: 20-1200 rpm Spindle taper: MK 5 Spindle stroke: 400 mm Feed rate: 0.063-0.63 m/min Vertical arm adjustment: 950 mm Electrical connection: 380 / 50 V / Hz Clamping surface of base plate: 1400x800 mm Total power requirement: 5 kW Machine weight approx.: 3 t Floor space required approx.: 2.2 x 1.0 x 2.8 m

Condition: good (used), Three-jaw chuck, three-jaw lathe chuck, 3-jaw chuck Dsdpfx Ajd Ew T Aofnokh -Mouth size: Ø 250 mm -Recess inlet: Ø 210 mm -Through hole: Ø 80 mm -Weight: 18 kg

Condition: good (used), Wedge bar chuck, three-jaw chuck, three-jaw lathe chuck, power chuck Dkedpfxed Itclj Afnsh -Mouth size: Ø 250 mm -Short cones: 8 -Thread: M30 -Gradient: 1.5 mm -Weight: 38.5 kg