Channel Bailing Press

PAAL PACOMAT V 50ton 500kg bale

Condition: ready for operation (used), Pressing force: approx. 700 kN (approx. 70 tons) Motor power: approx. 11 kW Power supply: 3 × 400 V / 50 Hz Single bale weight: up to approx. 600 kg Bale dimensions: approx. 1100 × 1100 × 1200 mm Machine dimensions: approx. 5.9 m length, 2.5 m width, approx. 2.6 m height Machine weight: approx. 7 tons Njdpfx Ajra Dddskqela Cycle time: approx. 45–47 s Construction features: - Large loading opening for cardboard - Possibility of automatic feeding (e.g., via conveyor) - Manual wire tying (4 wires) - Pallet lock and hydraulic doors for bale removal Advantages of this press: - Large bales – fewer transports - High pressing force - Designed for continuous operation Available production years: 2016–2020

Year of construction: 1986, condition: good (used), Technical Details : Products - - Flats - 10x3 - 25x3 mm 10x4 - 25x4 mm 12x5 - 20x5 mm - Square - 6x6 - 12x12 mm - (T) Profile - 20x10x3 mm - ( L) Profile - 15x15x3 - 18x18x3 mm Nodpfx Ajd H Ur Aokqola Raw Material wire - 8,9,10,11,12,13,14,16 mm Transformer Power - 20 Kw Speed - 35m/min

Condition: excellent (used), Year of construction: 2023, operating hours: 1,500 h, functionality: fully functional, cutting force: 630 t, power: 90 kW (122.37 HP), empty load weight: 36,500 kg, total width: 2,400 mm, total length: 9,500 mm, overall weight: 40,000 kg, cutting length (max.): 1,600 mm, year of last overhaul: 2024, type of input current: three-phase, operating pressure: 220 bar, Scrap shear MS-6300e (scrap shear with electric motor) without operating materials. A 250kW diesel generator can be offered separately. Model: MS-6300e Cutting force: 630t Cutting length: 1600mm Discharge height: 500mm Power: 110 KW Capacity: 12-17 t/h Machine weight: 40 tons (+ diesel generator 4 tons) Hopper size: 3850mm x 2600mm x 1500mm Nljdpjuu Upgsfx Akqea Information: A scrap shear is used for economical scrap cutting: - simple automatic operation - Energy-saving - Cost-saving - No foundation required Function: Scrap is fed into the loading area with the aid of an excavator. Due to the horizontal filling area and the scrap's own weight, it falls down into the loading chamber and into the cutting area. The scrap is compacted at the front wall and cut by the horizontally moving tool pick-up side via the blades on the front wall. While the tool carrier carriage moves horizontally, the processed material is pushed out via the blades on the front wall of the container. When returning to the rear position, the loaded scrap moves into the interior of the shears under its own weight. The scrap shears are available in different versions depending on customer requirements and the output size can be selected (for new orders). Inspection and trial operation are possible.

Year of construction: 2021, condition: new, machine/vehicle number: 2021102613, Aluminum angled conveyor belt with substructure Conveyor length: 2000mm flat + 2200mm rising Pitch angle in bend 45°C Discharge height: approx. 1800mm Height of the horizontal top edge 200mm PU conveyor belt Conveyor belt EM 9/2 0+05 PU petrol matt Belt width 500mm 21 pcs. T30 studs welded - pitch 310mm * antistatic due to threads in the fabric on the underside endlessly welded with stepped finger connection 40mm sidewall high-frequency welded on both sides * edge-free zone on both sides for tape guidance in the incline Full-surface underlay sheet Drive: Motor approx. 1.1KW Nledpfx Aksh Eld Eeqsa Belt speed approx. 0.4m/sec * optionally controllable with frequency converter Connection 220/400V, 50Hz protection class IP54

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Nlsdpfsvf E Avsx Akqea Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: new, Year of construction: 2025, Engine power 7,5kW - Cutting force 30to Nlsdpsgl Adzsfx Akqja Cutting channel designed for - max. roll length 1500mm - max. roll diameter 850mm - machine weight approx. 3500kg - tank capacity approx.110liter - hand guard in the area of the control panel and opposite to it -knife lock -splitter table straight execution -documentation 2-fold German ( 1x text form, 1x CD ) -color RAL 5012 - light blue protective grid/knife bar RAL 1028 melon yellow machine in stock and immediately available Price and further info on request

Condition: new, Year of construction: 2023, operating hours: 1 h, functionality: fully functional, overall weight: 5,200 kg, fuel type: diesel, color: beige, power: 513 kW (697.49 HP), output voltage: 400 V, output frequency: 50 Hz, type of output current: three-phase, nominal power: 408 kW (554.72 HP), nominal power (apparent): 510 kVA, continuous power: 368 kW (500.34 HP), total length: 4,460 mm, total width: 1,606 mm, total height: 2,493 mm, rotational speed (max.): 1,500 rpm, motor manufacturer: Doosan, type of cooling: water, AVS diesel generator set - stationary Type: DW 460 DO2 15 AK14A PRP output: 368 kW / 460 kVA ESP output: 408 kW / 510 kVA Operating hours: 1 Engine: DOOSAN DP158LC Power standby: 513 kW Speed: 1,500 rpm Operating voltage: 24 V Cooling: water-cooled Generator: Mecc Alte ECO 40-3S/4 B Voltage: 400/231 V Voltage regulator: DER-1/A Control panel: DSE 7320 - automatic emergency power supply Dimensions: 4460 x 1606 x 2493 mm (LxWxH) Weight: 5200 kg Equipment: Battery charger 5 Amper, battery disconnect switch Nlodoua Tl Aopfx Akqsa

Condition: ready for operation (used), DIXI 60SLD is a semi-automatic baling system with a pressing force of 60 tons, designed for economical volume reduction of recyclable residues in industrial and craft sectors: - Cardboard boxes - Foams - PET bottles - Insulation mats - and other pressable materials Horizontal baler, DIXI 60 SLD waste press with tipping device Technical specifications: Pressing force: 60 tons Specific pressure: 6.81 kg/cm² Power supply: 400V / 7.5kW Bale dimensions: 800 x 1100 x 1200 mm Number of ties: 3 Bale weight: approx. 370–410 kg Tying: manual Feed opening: 990 x 1110 mm Machine weight: 5,420 kg Average pressing cycle: 47 sec Year of manufacture: 2011–2016 Dixi 80SLD Baler Technical Data of the Baler Brand: Dixi Model: 80 SLD Pressing force: 80 tons Drive power: 11 kW, 400 V / 32 A Feed opening (W x H): 1040 x 1110 mm Pressing cycle: approx. 35 sec Throughput: approx. 1,000 kg/h Bale size (W x H x L): 1120 x 1120 x 1200 mm Bale weight: depending on material, approx. 500–600 kg Bale tying: triple, manual Machine dimensions: Length: 4,200 mm (+cage 1,600 mm) Width: 1,830 mm Height: 2,620 mm Machine weight: approx. 8,000 kg Automatic bale ejection Robust construction for long-term use Year of manufacture: 2016–2020 Nedpfx Aora A E Uokqola Weight: approx. 8.4 tons Condition: Used

Year of construction: 1988, condition: good (used), A complete Atlas Copco air compressor including Donaldson Ultra Filter and a Tank in good working condition Nedpfx Ashpx U Aokqola

Condition: new, Hopper opening: 2.500 x 2.000 mm Rotors: 2 pcs. Rotor flight circle: 580 mm each Rotor design: 5 and 6 cutting teeth Drive: 2 x 90 kW with planetary gears Hydraulic screen flap interlock for the discharge of contaminants Weight: approx. 18.500 kg Njdpfxjbq St Hj Akqjla