Condition: used, functionality: fully functional, Year of construction: 2015, machine/vehicle number: 75E-E188, USED SHRED-TECH DUAL SHAFT 80HP (TWIN 40) SHREDDER MODEL ST-75ES MANUFACUTRED 2015 TWIN 40 HP MOTORS DUTTING CHAMBER OF 956mm/37" X 635mm/25" Cjljxmthrohccqrjrc DISCHARGE HEIGHT 1,067mm/42" THIS WAS USED IN A PLASTICS COMPANY TO SHRED PLASTICS, CARDBOARD AND LIGHT GUAGE METAL. IT IS IN VERY GOOD CONDITION, PURCHASED DUE TO A PLANT CLOSURE. IT IS CURRENTLY LOCATED IN OUR WISCONSIN WAREHOUSE.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 13,209 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,050 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 700 mm, bale weight: 500 kg, oil tank capacity: 400 l, power: 15 kW (20.39 HP), year of last overhaul: 2025, volume flow: 108 m³/h, Technical data baler: Manufacturer according to type plate BRAMIDAN (original manufacturer Presto GmbH & Co. KG) Type HC 50 (corresponds to the Presto HPK 50) Year of manufacture 2007 Operating hours 13,209 hours, as of March 2026 Number of bales pressed: 23,379 bales Pressing force 50 tonnes Specific pressing force 650 kN/m² Feed chute dimensions 1250 x 1050 mm (L x W) Filling volume 0.96 cm³ Theoretical cycle time 32 seconds Theoretical throughput capacity 108 m³/hour Bale dimensions 1100 x 700 mm (w x h) length variable Drive power 15 kW Power consumption, total in 50 A Tying 4-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm approx. 3.1 t/hour Bulk weight of 60 kg/cbm approx. 4.5 tonnes/hour Bulk weight of 100 kg/cbm approx. 7.2 tonnes/hour Bale weights with a bale length of approx. 1.2 m up to 500 kg, depending on material Colozbxyqshccqrorc Hydraulic oil tank capacity 400 litres PLC control Siemens S7-200 Effective transport dimensions excluding baler 6850 x 1950 x 2650 mm (l x w x h) Transport weight of press 8.5 tonnes Condition of the baler: The press was used in a production facility exclusively for pressing cardboard and was regularly serviced. With only 13,209 operating hours, the machine has seen little use. The press was partially overhauled in our workshop and then tested. The following overhaul work was carried out: Machine cleaned Bale retainer made operational and lubricated Light barrier replaced Twisting unit completely dismantled, broken down into individual parts, all bearings replaced, all plastic glides replaced, lubricated, chain tension adjusted Knife and counter knife dismantled, sharpened, reassembled Knife gap readjusted General maintenance work carried out and lubricated Scope of delivery: 1 baler with wire coil boxes, without wire (6850 x 1950 x 2650 mm) 1 bale chute (5100 x 1150 x 450 mm) 1 floor-mounted wire coil box (1450 x 380 x 360 mm) To transport the baler, you will need a tautliner with an effective internal height of 2700 mm. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, oil tank capacity: 600 l, power: 22 kW (29.91 HP), year of last overhaul: 2025, volume flow: 530 m³/h, For sale is a partially refurbished Presona baling press, with 50 t pressing force, 22 kW drive power, built in 2005 Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the whirling unit replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Crolhccqozbxxajrsc Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, For sale is a complete Bollegraaf baling system consisting of conveyor technology, baling press and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Crelhccqezbxw Aerec Tying system 5-fold vertical Throughput rate at a bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Comments: The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. Crolhcjzbxwiecqrec • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, year of last overhaul: 2025, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Crjlezbxvljhccqrec Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Used Thetford International T3 waste compactor. Celhccqehvi Ahjrjrc

Condition: good (used), Year of construction: 1990, Roll compactor, Bergmann – used: Price ex works: only €950 (net) Manufacturer: Bergmann Type: PS 8100E Year of manufacture: 1990 Serial number: 05 3658 2845/90 Pressing pressure: to Weight: 750 kg Crelhccqszbygrjroc 400V, 5.5 kW Condition: good Available: from Q4/2026 Location: Hamburg Efficient waste compaction: A special steel drum enables effective collection, shredding and compaction of the waste, reducing its volume up to ninefold. Continuous filling: The machine allows for continuous filling by all users. The feed shaft can also remain open during the working process, which facilitates and accelerates waste compaction.

Condition: good (used), Year of construction: 1999, Baling presses, HSM, 30-ton pressing force – used: Price ex works: only €2,950 (net) Crjlozbygfehccqrjc Manufacturer: HSM Type: 225.1 VL Year of manufacture: 1999 Machine number: 6124.834. N Serial number: 200014505 Pressing force: 30 tons 400V, 5.5kW Condition: good Available: from Q4/2026 Location: Hamburg

Condition: good (used), Year of construction: 2014, Large waste compactor / cardboard press, Höma, – used: Price at location: only €18,950 (net) for self-dismantling! Manufacturer: Höma Type: PB4000 Year of manufacture: 2014 Machine number: 140409 Weight: 1,200 kg Pressing force: not specified, but we estimate 40 tons. The press has a second discharge chute. Price includes a small crane with trolley. 30 kW Condition: good Celjzbyf Ijhccqrerc Available: from Q4/2026 Location: Hamburg For an additional charge, a conveyor system for empty cardboard boxes, over 100 m long, is available! Photos at the end of the advertisement!

Condition: excellent (used), N.PREVIERO shredder Blade: 1,000 Engine: 170 kW Complete with conveyors and dosing systems. Colhcoza Epijcqrsrc

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, power: 9.7 kW (13.19 HP), Technical data cardboard shredder: Manufacturer Presto GmbH & Co. KG Type PZA Year of construction 2007 Throughput volume 130 m³/hour Speed 37/9 rpm Motor power 7,5 / 2,2 kW Electrical connection 32 A Dimensions shredder inside 1,490 x 1,320 x 530 mm (L x W x H) Dimensions shredder outside without cover 2,308 x 1,320 x 685 mm (l x w x h) Machine weight 0,45 tons Use of the systems: The PZA cardboard shredder was in use in a Dutch logistics centre to pre-shred loose, erected cardboard boxes from the returns department and then press them into bales. The cartons were fed manually onto the infeed conveyor and transported directly to the cardboard shredder by a sliding belt conveyor and shredded. The pre-shredded cardboard boxes were then transported over hundreds of metres to the baler where they were pressed. Scope of delivery: 1 piece Presto cardboard shredder (2-shaft shredder) type PZA Comments: Celou Tha Ishccqrorc The cardboard shredder was an elementary part of the disposal line and therefore good maintained to ensure high availability of the returns department. The machine is in good condition and ready for immediate use. The price is per piece exw. our warehouse in Siddeburen, the Netherlands. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: fully functional, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Cslhccqsu Thh Eerorc Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating instructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. Crslhccsvf E Avsqrsc The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 2018, operating hours: 4,163 h, condition: used, functionality: fully functional, power: 83 kW (112.85 HP), overall weight: 31,500 kg, hopper volume: 7,000 l, machine/vehicle number: PID000123KDGI16212, Belt feeder for stockpiles 2-deck heavy-duty screening machine Engine: Cat-C4.4 Dual power system Hopper extension Telescoping side conveyors Transport dimensions: 15,380 x 2,860 x 3,390 mm (L x W x H) Cslhccqszbri Eerjrc

Condition: used, Year of construction: 2018, operating hours: 3,297 h, functionality: limited functionality, Features of the basic unit: Infeed conveyor: •Highly wear-resistant, forged special chain •Infeed conveyor width: 1,700 mm •Infeed conveyor length: 4,700 mm Hydraulic system: •Infeed roller and infeed conveyor each with a separate drive and gearbox. The speeds of the infeed conveyor and the infeed roller are continuously adjustable. Overload protection through speed monitoring and reversing mechanism. Hydraulic tank with a capacity of 220 liters. Infeed: •The infeed roller is hydraulically driven, pendulum-mounted, and guided by 2 rack and pinion systems. •The infeed opening is approximately 660 mm high and 1,700 mm wide. Hammer mill: •46 hammers, hammer width: 80 mm •Hammer tips can be individually replaced •Hammer mill width: 1,700 mm •Rotor diameter: 999 mm •Rotor speed: 1,000 rpm Motor: Croleza S Hnshccqrjc •SCANIA turbo diesel with a power output of P = 478 kW, compliant with current Euro emission standards Drive: •Direct drive via 8 V-belts Hopper dimensions: •Hopper opening length: 4,800 mm •Hopper opening width: 2,400 mm Throughput capacity: •200-300 m³/h and more, depending on the material Delivery date will be agreed upon.

Condition: ready for operation (used), * Brand: Kleemann * Beltwidth: 1400 mm. * Driving: 15 kW Gearbox. * on Stock: 1 piece Crelhjywm Snoccqrjc

Condition: used, Year of construction: 2021, operating hours: 4,200 h, Equipment: Basic package Inventhor 9: - MTU diesel engine 6R1300, 390 kW at 1,700 rpm, compliant with EUROMOT V emissions standard - Auxiliary hydraulic connection 30 l/min and 70 l/min Cslhcjyu Svxscqrorc - Roller drive via planetary gearbox 380 kW – VARIO – - Load-sensing system - Fuel tank 950 liters - Longitudinal conveyor: belt length 4,450 mm, belt width 1,000 mm - Centrally arranged wear strips - 24 V electric control system - Additional electric pump for operating the following functions when the engine is switched off: “Raise/lower/fold rear conveyor, open/close comb flap, open/close comb, raise/lower optional permanent magnet belt, raise/lower optional folding hopper” - Complete radio remote control - Large lateral GRP maintenance doors - Maintenance-friendly engine compartment with LED lighting - Hydraulically reversible fan - Loader protection on both sides - Fire extinguisher - Maintenance ladder - Toolbox - Acoustic start-up warning - Doppstadt telematics system - Paintwork: RAL2011 deep orange Additional equipment: - 3-axle semi-trailer chassis unit - Shredding system Size “L-C3” VARIOMAT - Size “L” limiter (20 pieces) - Hydraulic drive system - Double-sided watering system - Rear conveyor 8.5 m, 1,200 mm wide - Overbelt magnet Neodymium - Frame for overbelt magnet Neodymium - Central lubrication system with pump - LED light package for engine compartment and rear Delivery date to be arranged.

Condition: refurbished (used), “SGM DIS 100” for Sale Manufacturer: SGM Magnetics Type: DIS 100 Belt widthness: 1.000 mm (New belt) Included: Cjlhccqoy U N Exorerc – New Control-unit Eddy Current Separator is overhauled, sandblasted and painted.

Condition: used, Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Replacement of all plastic sliding plates for the hydraulic push floor. Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. Crsljy Urtfshccqrjc The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. All six limit switches (proximity sensors) on the push floor were replaced. The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2026, The shredder breaks large, bulky pieces made of Styrofoam and EPS and similar materials with a maximum raw density of 30kg/m³ into small pieces. The shredder reduces the volume by around 65%. This makes the machine ideal for use in industrial and craft companies as well as for wholesale and retail trade with Styrofoam packaging material. Throughput: Sieve 10 mm: approx. 3 m³/h Sieve 20 mm: approx. 8 m³/h Sieve 30 mm: approx. 13 m³/h Sieve 40 mm: approx. 18 m³/h Sieve 50 mm: approx. 23 m³/h Depending on the sieve set, the volume can be reduced by 3:1 just by shredding your Styrofoam residues. Custom-made products are available on request. VAT is shown separately on the invoice. Shipping included throughout Germany, islands with surcharge. Cslhccqexlzkrerjrc If you have any questions, please feel free to contact us.

Condition: as good as new (ex-display), Year of construction: 2025, The shredder breaks large, bulky pieces made of Styrofoam and EPS and similar materials with a maximum raw density of 30kg/m³ into small pieces. The shredder reduces the volume by around 65%. This makes the machine ideal for use in industrial and craft companies as well as for wholesale and retail trade with Styrofoam packaging material. Crolhccqjza D U Rjrec Throughput: Sieve 10 mm: approx. 3 m³/h Sieve 20 mm: approx. 8 m³/h Sieve 30 mm: approx. 13 m³/h Sieve 40 mm: approx. 18 m³/h Sieve 50 mm: approx. 23 m³/h Depending on the sieve set, the volume can be reduced by 3:1 just by shredding your Styrofoam residues. Custom-made products are available on request. VAT is shown separately on the invoice. Shipping included throughout Germany, islands with surcharge. If you have any questions, please feel free to contact us.

Year of construction: 2007, operating hours: 6,915 h, condition: used, 2007 | Powerscreen Turbo Chieftain 1800 | Used Screen | 6915 hours 📍Location: France 🚛 Delivery available to your destination – Use our shipping calculator to estimate transport costs! 💰 Buy Now for EUR 72800 or Make an Offer. Payment at delivery available for an affordable fee (subject to approval)* 👷‍♂️ Inspected by an independent expert 77 inspection points 51 approved ✅ 8 imperfect ℹ️ 0 issues ⚠️ 📌 Inspector's Comment: Good overall and operational condition. New engine replaced in 2025. Vibrator covers are removed for transport. 📄 Want to see the full inspection, extra photos, or a video? Tip: The reference "40853 Equippo" is commonly used when looking up more details online. 💡 Why this machine and our service stands out: ✔ Thorough inspection by professionals Cjlhccoy U Nl Ejqrjrc ✔ Jobsite delivery available ✔ Money-Back Guaranteed ✔ Secure and flexible payment options 🔄 Considering other equipment options? We offer helpful tools and resources for all equipment owners and operators – easily accessible on our platform.

Condition: like new (used), Year of construction: 2026, functionality: fully functional, TRI OPTIQUE Manufacturer: PELLENC Type: M 2800 BB HR Crelhccjyy Aa Tjqroc Working width: 2,800 mm Option installed in June 2024: separator for all types of metal, including stainless steel, metal sensor. New belt. The machine is capable of sorting all types of plastic by quality, all metals including stainless steel, and wood. The machine has just been serviced. Feeding system: Manufacturer: SINEX Type: MU 75 6500 Power: 2 x 3 kW Output conveyor 1: Manufacturer: RMIS Output conveyor 2: Manufacturer: ARVAL

Condition: used, Stationäre Absaugung mit Filteranlage / Stationary Extraction Eystem with Filtration Unit TEKA Filtercube 4H HV 11kW Stationäre Absaugung mit Filteranlage / Stationary Extraction Eystem with Filtration Unit TEKA Filtercube 4H HV 11kW TEKA-Dosiereinrichtung für Precoat, Filterpatronen gegen Verkleben schützen /  TEKA Precoat Dosing Unit: Protecting Filter Cartridges Against Clogging Baujahr / Year 2018 - Serial-No. 9501442110402 Filtersteuerung mit automatische Filterabreinigung / Filter Control with Automatic Filter Cleaning Motorleistung 11 kW / Motor power 11 kW Leistungsstarker Ventilator mit Steuerung / High-Performance Fan with Controls Ausführung SelfClean / SelfClean Version Ausstattung / Equipment: Standard Filterpatronen, Filterfläche je nach Luftleistung / 4 standard filter cartridges; filter area varies depending on airflow capacity Display gesteuerte Filterabreinigung / Display-controlled filter cleaning Ventilatorsteuerung / Fan Control Bogenschalldämpfer für Luftaustritt nach oben / Elbow Silencer for Upward Air Discharge Cjlhccqjzav Eborjrc Rauche und Stäube werden mit einer Filterleistung von über 99 % sicher abgeschieden / Smoke and dust are safely separated with a filtration efficiency of over 99% Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test