Center grinding machine

Technica 5100

Condition: used, Technical Data Manufacturer: Technica Model: 5100 Design: Centre grinding machine with vertical construction Workpiece holding: Between centres with tailstock and guide Grinding spindle: High-speed grinding spindle Equipment: Various grinding wheels and live centres included Maximum workpiece length: 1100 mm Minimum workpiece length: 50 mm Maximum workpiece diameter: 125 mm Minimum workpiece diameter: 8 mm Centre height above guide: 145 mm Dsdsyw Rr Eepfx Affour Centre height above carriage: 65 mm Centre hole taper angle: 60° Maximum centre hole diameter: 50 mm Minimum core hole diameter: 2 mm Weight: 460 kg Dimensions: 850 x 750 x 1850 mm Condition: Used, good No guarantee is given for the correctness, completeness, and up-to-dateness of the information provided.

Condition: good (used), Year of construction: 2004, functionality: fully functional, Manufacturer: HABERMEHL Anlagenbau GmbH Address: Hauptstr.1, 35510 Butzbach-Ebersgöns, Germany Duodpfxsw Niuhj Affjr Type: EH 400/1 Serial number: 901 Year of manufacture: 2004 Voltage / Frequency: 400 V / 50 Hz Rated power: 3 kW CE-certified: Yes 🛠️ Device Description Industrial shredder or crusher (Shredder/Granulator). Notable features visible in the photos: - System with rotating knives (shredding unit) on a 2 mm shaft - 3 kW SEW motor and reduction gearbox - 8 mm screen (the screen is labeled “8 mm Sieb”) – determines the output particle size - Rollable, portable design - Material discharge container and lower motor drive system Machines of this type are typically used for shredding the following materials: - Plastics - Rubber - Wood - Light metal chips - Electronic scrap 📝 Technical information you should request If you require further details, you may request the following information from the supplier or manufacturer:

Condition: excellent (used), Year of construction: 2000, Description to follow! Dujdpfoyrtwxex Affer

Condition: used, Year of construction: 1977, Machine type: center‑hole grinding machine Dodpfxswwrdij Affjur Model: AG 5100 Year of manufacture: approx. 1975–2000 (various serials) Center distance (grinding stroke): 50 mm to 2,000 mm Workpiece spindle capacity: 8 mm to 125 mm diameter Workpiece swing over tailstock guide: approx. 290 mm Swing over grinding‑head column: approx. 300 mm Maximum workpiece weight: approx. 250 kg Center‑hole taper range: 2 mm to 50 mm diameter Center‑hole taper angle: approx. 60° Chuck capacity: approx. 4 mm to 150 mm Grinding‑head vertical stroke (coarse adjustment): approx. 130 mm Fine feed range of grinding pin: 0.01 mm to 1 mm per revolution Grinding‑pin diameter: 20 mm to 60 mm Grinding‑spindle speeds: 13,000 rpm to 45,000 rpm Spindle drive: approx. 0.5 kW Machine power supply: 400 V, 50 Hz Machine weight: approx. 1,000 kg Dimensions (L × W × H): approx. 1,900 mm × 600 mm × 1,800 mm Lubrication/cooling: pneumatic oil‑mist lubrication of grinding spindle Orifice for long workpieces in machine base, tailstock height adjustable with carbide inlays and live center Manual dressing device mounted laterally on grind spindle, approx. 40 mm stroke with pendulum swing for accurate taper Fold‑down pre-centering device for workpiece No workpiece drive via tailstock (passive center)

Condition: used, Year of construction: 1983, internal diameter min / max: 10 / 250 mm grinding depth 400 mm external diameter max. 380 mm swing dia. 390 mm table travel max. 550 mm stroke of the table min. 2 mm rapid traverse 10 m/min table speed -stepless- 0 - 10 m/min rough adjustment 18 mm fine adjustment 4 mm max. workpiece weight 100 kg spindle head B 6 DIN 55021 spindle turning speed - stepless 15 - 1.500 U/min pivoting angle +/- 30 Grad spindle bore 50 mm power capacity 2 kW rapid traverse 0 - 250 mm/min stroke 70 mm power requirement 3 kW weight of the machine ca. 2,7 t dimensions of the machine ca. 3,0 x 3,0 x 3,2 m Internal Grinding Machine Duedpfsvprxfjx Affer BAHMÜLLER - JES 12 - new control (July 2015)

Condition: good (used), Centre bore 2- 50 mm Diameter of workpiece 8 - 125 mm Lenght of workpiece 50 - 1000 mm Grinding wheel speeds 13'000 - 45'000 rpm Misc.accessories Dsdpfxerivlue Affeur MARCELS MASCHINEN AG

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 1315/451, Completely overhauled: Mechanics, geometry, hydraulics, and electrical parts (checked and/or replaced) Wheelhead: Disassembled, parts cleaned, worn or defective components replaced, motor overhauled, bearings replaced, belts replaced, spindle disassembled, seals and O-rings replaced, adjustments made. Newly painted. Workhead: Disassembled, parts cleaned, worn or defective components replaced, motor overhauled, belts replaced. New spindle bearings. Newly painted. Tailstock: Disassembled, inspected, overhauled. Hydraulics: Disassembled, motor checked, hoses replaced, defective and worn parts replaced. Hydraulic block checked. X-axis: Disassembled, all worn parts such as O-rings, seals, segments, etc. replaced, hydraulic piston overhauled, table ground. Z-axis: Disassembled, table ground, worn or defective parts replaced, hydraulic piston overhauled, newly painted. Electrical cabinet: Completely checked, various relays replaced. Paintwork: Colors: White RAL 9003 and Grey RAL 7011 Geometry according to manufacturer's protocol. Various accessories checked and cleaned. Origin: CH Voltage: 380 / 50 / 3 Net weight: approx. 2,200 kg Customs tariff number: 8460.2920 TECHNICAL SPECIFICATIONS Nominal distance between centers: 600 mm Max. distance between centers (with extended headstock): 750 mm Center height, standard: 125 mm Center height with interchangeable pads for heads: 175–250 mm Max. workpiece diameter (125 mm center height): 250 mm Max. workpiece diameter with interchangeable pads: 350–500 mm Swiveling range of table in each direction: 10° Max. grinding length for flat surfaces (max. width = 200 mm): 900 mm Continuously variable hydraulic table speed: up to approx. 6 m/min Table reversal delay: 0–5 sec Grinding wheel for external grinding, diameter - width - bore: 400x50x127 mm Grinding wheel for flat surface grinding: 250x13x76 mm Wheelhead spindle speed: 1,500/1,700/2,200/3,600 rpm Wheelhead swiveling range: 270°, with indexing every 90° Vertical travel of wheelhead, center height: 125–350 mm Dedpjw U Ry Nefx Affeur Transverse travel of wheelhead: 285 mm Hydraulic rapid traverse stroke: 40 mm Intermittent infeed of wheel by table reversal: 0.001–0.03 mm/dia Continuous infeed for plunge grinding: 0–0.9 mm/dia Micrometric infeed stop, by division: 0.001 mm/dia Workhead swiveling range: 360° Workhead spindle speed, stepless: normal/special: 20–400 / 10–400 rpm Internal taper of workhead/tailstock: Morse 5/3 Wheelhead motor: approx. 4 HP All technical specifications are given without obligation and subject to errors or omissions.

Condition: used, grinding diameter 350 mm grinding length 600 mm centre height 175 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0-9,99 mm/Ø 0-9,99 mm/Ø ±10 ° longitudinal feed of the table 1100 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannung kg cross travel max. 270 mm 80 mm tailstock quill taper MT 3 quill travel 30 mm total power requirement 6,5 kW weight of the machine ca. 3,05 t dimensions of the machine ca. 4 x 2 m Overhauled according to Kellenberger guidelines including new, modern and future-proof control system. Photo of already delivered machine in centre distance 1000mm. -Operation via the touch panel is extremely simple. -The symbols on the control panel are practically identical to the original original control system, so there is no need for familiarisation. -Diagnostic function with display of PLC messages and digital I/O -Dressing function can be extended or changed at the customer's request. -Orientated spindle stop of the workpiece spindle possible on request. -New maximum infeed of 40 mm can be extended on request. -Digital display in 2 axes. Resolution x-axis 0.5my Options: -Encoder with digital display in the workpiece headstock -Rotary encoder with digital display in the grinding headstock (no height adjustment with spindle possible) with spindle possible) -New stable internal grinding device diameter 80mm or 100mm with height adjustment. -Increase of the centre height to max. 225mm Duedpfjuxft Ejx Affsr -Speed control for the grinding spindle Included: -Operating tool -Clamping tube for chuck Further accessories on request. The x-axis of the machine has an electronically controlled infeed system with stepper motor drive. Hydraulic longitudinal and rapid traverse table movement. Versatile application in production for external cylindrical and internal internal grinding or for external, face and internal grinding in one clamping clamping of individual parts. Possible options: -Semi-automatic dressing cycles for external and internal grinding -automatic dressing compensation. -Measuring control

Condition: used, Year of construction: 1992, spindle speed (min.): 7,500 rpm, spindle speed (max.): 24,000 rpm, 4 motorized grinding spindles (liquid-cooled, purge air / oil mist lubrication) including REFU HF frequency converter, e.g. for powering the spindles of a Voumard 400 CNC T4. Grinding spindle GMN TSSV 170-7500 7,500 rpm, 350V, 19.3A, 7.5kW, 250 Hz Grinding spindle Voumard BM15-170 15,000 rpm, 350V, 35A, 18kW, 250 Hz Grinding spindle Voumard BM18-15032 18,000 rpm, 350V, 28.5A, 12kW, 600 Hz Grinding spindle Voumard BM24-150 24,000 rpm, 350V, 27A, 12kW, 800 Hz REFU HF Converter 316/25 Dusdjl Tn Afspfx Affjr High-frequency converter (inverter, frequency inverter) Frequency converter / inverter for powering motor spindles GMN tool spindle, motorized grinding spindle The spindles are fully functional, sold as is – manufacturing year approx. 1992 A collection of various grinding spindle shafts / arbors for grinding wheels is available for these spindles and can be purchased separately. Price / details on request All technical data subject to error or omission. We sell exclusively to countries within the European Community.

Year of construction: 1983, condition: ready for operation (used), Was used to rework profile rollers for a hot rolling mill, was regularly serviced, with accessories, without spare parts, on-site inspection is possible, no videos available. Djdjriwfiopfx Affsur