Single shaft shredder

Vecoplan VAZ 1300 KK

Year of construction: 2026, condition: new, -Drum diameter 1600mm -Drum length 2880-3880-4880mm -Working length 2000-3000-4000mm -Grid holes according to your specifications -The screen consists of a closed profile -A cleaning brush with a diameter of 300 mm is mounted on the screen and along the entire length of the working part -Flat bar blades installed in the center of the drum allow the material to be poured -Drum rotation speed approx. 11.5 rpm - Sieve feed sieve via gearmotor- Drum transmission via gearmotor + 2 rubber drive wheels diameter 230 mm - Sieve equipped with electrical panel - Gravity feed hopper, dimensions Width 1600 mm, Length 1400 mm, Height 1200 mm - 12 months warranty Lhsdpsq T Sp Hsfx Akqof - Made in Europe - CE compliant

Condition: good (used), Year of construction: 2004, functionality: fully functional, Manufacturer: HABERMEHL Anlagenbau GmbH Address: Hauptstr.1, 35510 Butzbach-Ebersgöns, Germany Type: EH 400/1 Serial number: 901 Year of manufacture: 2004 Voltage / Frequency: 400 V / 50 Hz Rated power: 3 kW CE-certified: Yes 🛠️ Device Description Industrial shredder or crusher (Shredder/Granulator). Notable features visible in the photos: - System with rotating knives (shredding unit) on a 2 mm shaft - 3 kW SEW motor and reduction gearbox - 8 mm screen (the screen is labeled “8 mm Sieb”) – determines the output particle size - Rollable, portable design - Material discharge container and lower motor drive system Machines of this type are typically used for shredding the following materials: - Plastics - Rubber - Wood Lodpfxew Niuhs Akqohf - Light metal chips - Electronic scrap 📝 Technical information you should request If you require further details, you may request the following information from the supplier or manufacturer:

Condition: used, Total height 6500 mm Floor space 2000 x 2000 mm Outdoor installation Compact filter series Model PKFP – 1 element – 1.92 x 1.92 Shaking filter Overpressure operation Filter hose length 2500 m long – 180 mm diameter - then 105 m2 filter area 2 raw air fans – 2 pipes (diameter 300 mm) 1 x fan KT 300, 15 kW power 6361 m³/h built in 1999 1 x fan S 25 / 300, 7.5 kW power 7400 m³/h, built in 1993 1 x transport fan 6.1 kW, power 57 m³/min, built in 1996 Total approx. 14,000 m3/h volume flow Briquette press Höcker Polytechnik type BrikStar C 3 - 12. 1225 Motor 3.0 kW, briquette diameter 65 mm, output approx. 40-45 kg/h depending on the specific weight of the material. Ledpfx Akevviytoqjhf Storage location: Nattheim

Condition: refurbished (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 12786 040, overall weight: 20,000 kg, rotor diameter: 640 mm, total length: 4,900 mm, total height: 2,600 mm, total width: 4,100 mm, rotor width: 2,000 mm, power: 203 kW (276.00 HP), rotational speed (max.): 340 rpm, input current: 415 A, Equipment: rotational speed infinitely variable, The Vecoplan VAZ 2000 M F-T is a powerful single-shaft shredder. This robust shredder offers an efficient and reliable solution for a wide range of applications. Possible applications: - Household waste - plastics - paper With its proven technology and high throughput of 4-5 tons per hour, the VAZ 2000 M F-T is the perfect choice for shredding and volume reduction in disposal and recycling processes. The pictures are examples. The pictures do not show the machine as it is offered, they only serve as an example of what the machine will look like after the overhaul. Price on request. Lhedeurkc Rjpfx Akqef

Year of construction: 2011, condition: good (used), Shredder system, single-shaft shredder, shredder, chipper, cutting mill, single-shaft crusher, rotor mill -Shredder system: completely made of stainless steel, for frozen meat or other -Motor power: 4 kW -Speed: approx. 60 rpm -Number of cutting knives: 10 pieces Lhjdpfxoh Di H Do Akqsf -Dimensions cutting blade: 250 mm -Filling spout 500 x 895 x H480 mm -Dimension 880/1390/H2060 mm -Weight 640 kg

Condition: used, SPE Renergi Low Temperature Dryer. Lhsdpfswp Rqfox Akqof The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: used, Year of construction: 2003, operating hours: 10,120 h, total length: 1,800 mm, total height: 1,700 mm, total width: 1,200 mm, Empty weight: 1.300 kg Price: On request Lodpewh Na Njfx Akqjhf Shredder Untha LR 630 Year of construction 2003 Input opening: 624 x 792 mm Throughput speed: material and sieve dependent Rotor diameter: 248 mm Rotor speed: 86 - 96 rpm Engine power: 15 kW Cutting system: 17 knives Sieve diameter 24mm Transport dimensions 1800*1200*1700mm (L*W*H), Weight 1300kg - Year: 2003 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: LR632318 - Operating hours: 10120 - Transport dimensions: 1800mm x 1200mm x 1700mm (l x w x h) - Transport weight [kg]: 1300kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Year of construction: 1998, condition: excellent (used), NEUE HERBOLD cutting mill / granulator Universal mill - heavy version Made in stainless steel -Year of construction 1998 - made of stainless steel - from technical center (machine was used exclusively for test/demonstration purposes - Rotor diameter: 300 mm Lodpfx Aksh Rwc Eeqjhf - Working width: 500 mm - 3 rows of knives

Condition: new, Year of construction: 2024, Chopper Knife 40 x 40 concave Ljdpfobxu Dhjx Akqshf Knife for Weima, Large ..... For almost all common chippers / shredders From stock Bitburg Subject to prior sale

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 Lhodpeu Hmacsfx Akqof 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted