Single-screw extruder ES 75 - 28 L/D

Alpahtec A-ES 75.28 V

Year of construction: 2004, condition: reconditioned (used), Stock-No. 2054 1used, partly overhauled and functionally tested Nwodpfx Asiyya Asg Isc Single-screw extruder AlphaTec A-ES 75.28 Screw –Ø 75 mm- 28 LD main drive 75 kW- AC Screw speed up to 80 r.p.m. - adjustable 1x venting port with vacuum-pump cylinder barrel heating apporx. 30 kW installed 3x additional temperature controller for down-stream equipment Control board overhauled You´re welcome for inspection visit in our stock Wuppertal-Germany More extruders available

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION Nedpfx Aowu Tu Djg Iswc 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Njdpfx Ajvgrh Uog Ijwc Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Year of construction: 2025, condition: reconditioned (used), functionality: fully functional, Van Dam 620 8 colour cupprinter Njdpfx Asn R Eb Isg Iswc Machine will come fully remanufactured including new year of build and new electrical cabinet. looks, operation and performance like a new printing machine. CO2 footprint up t80% lower; costs much lower compared to new machinery.

Condition: used, Year of construction: 2014, power capacity 3 kW feed pressure 7 bar liter capacity / l weight 286 kg Chicago Pneumatic CPVR15 CE screw compressor - Year of manufacture 2014 The CPVR15 CE impresses with its robust design, long service life and low operating costs. Whether in workshops, workshops or industrial applications - this compressor reliably supplies you with the compressed air you need. Drive power: 3 kW Delivery pressure: 7 bar Air output: up to 58 CFM (approx. 1,640 l/min) at 7 bar Weight: 286 kg Dimensions: approx. 965 mm (L) × 620 mm (W) × 1,040 mm (H) Operating noise: approx. 50-58 dB(A) Voltage/frequency: 415 V / 50 Hz Application: Workshops, craft businesses, industrial applications with medium compressed air requirements Nwsdsh A Sfdspfx Ag Isc Included in delivery: 1x compressor - Chicago Pneumatic CPVR15 CE 1x refrigeration dryer - OMI ESD 108 - 0.70kW 1x Beko Öwamat 2 - oil-water separator Technical data was taken from publicly available sources

Condition: good (used), functionality: fully functional, We offer for sale a complete line for multi-point automatic welding of SCHLATTER brand steel wires. Nwjdjtvpilopfx Ag Isc We have three fully operational production lines. There are also automatic machines for the production of transverse wires (so called slitting machines with a cutter). We also have a number of single point welding machines for steel wires.

Condition: excellent (used), Line for door jambs (frames), with END-CUTTING, ROUTERING for COUNTER-PLATE and HINGE INSERTION (Anuba). Composed of: Nwodpfx Ajqwyclsg Ijc X10030A) Loading Conveyor X10030B) Transfer Conveyor X10030C) Double-end cutting and drilling machine "AMS" - Left-side Cutting 45° - Drilling - Cutting 90° - Right-side Cutting 45° - Drilling X10030D) Angular Conveyor (90°) X10030E) Anuba Inserting Machine "MASTERWOOD" Mod. MULTITEC X10030F) Strike Plate Routering Machine "MASTERWOOD" Mod. Teknomat 3000

Condition: new, messurements (LxWxH): 1.630 x 700 x 1.200weight approx.: 480total power requirements: 1,1prebending: 2sheet thickness: 3sheet length: 1050 Nwjdpfed Eqqqox Ag Isc

Year of construction: 2008, condition: like new (used), Polytype 8 Colors Printing Cup , Type BDM 691, Year 2008 Colours : 8 colours Maximum output/hour : 36.000 cups/hour Nwsdpfx Agshbdacj Ioc Minimum cup diameter : 60 mm Maximum cup diameter : 100 mm Minimum cup height : 35 mm Maximum cup height : 160 mm UV system : Uviterno Pre treatment : Corona, Arcotec Reference : B-21020

Condition: good (used), TECHNICAL DATA - Main beam: IPE 600 mm (various sizes & load capacities available) - Secondary beam: Sigma 410 mm (220 & 260 mm also available) - Decking: P6 chipboard, double-sided coated, 38 mm - Load capacity: 500 - 1,000 kg / m² - Colour: RAL 9010 Pure White - Condition: used Large quantities available immediately from stock in Nordhorn. The IPE 600 allows for large spans! Scope of delivery: - Columns - Main and secondary beams - Bracing crosses - Flooring PRICES: from €40.00 net per m² Prices may vary depending on design (load capacity and column spacing). Please contact our team for a consultation. Optional accessories - Handrail - Flush wall connection - Staircase - Transfer station - Impact protection YOUR CONTACT PARTNERS: - Tanja Henkelmann - Rainer Nürenberg - Oliver Kopp TRANSPORT & INSTALLATION We are happy to assist with the transport and installation of the item. Pickup is available. Delivery or shipping can be arranged for an additional charge. Additional costs depend on the delivery location and shipment size and can be quoted individually. PAYMENT TERMS Payment terms are to be agreed upon when placing an order. The price is to be understood as a unit/net price or as stated in the description (plus VAT). Naturally, you will receive an invoice with VAT shown. ABOUT US Nwjdpfxjgpxf Ho Ag Ijc DLK, based in Nordhorn, supplies new and used products in the areas of warehouse logistics, conveyor technology, mezzanine floors, textile storage, as well as machinery for trade, industry, and crafts. We continuously offer attractive used equipment from various manufacturers/brands at competitive terms. Please feel free to contact us with any questions. Four wins – The DLK success pillars – Warehouse Technology | Levelmaker® | Logistics | Solutions