Decoiler

ASSERVIMENTI SMD 15 S

Condition: excellent (used), functionality: fully functional, Year of construction: 1984, Loading capacity: max. 300 Kg. Diameter of decoiler: 1.000 mm Lsdpfx Aiof S I I Hekorl Diameter of spool: max. 900 mm Inside diam of spool: 240 - 560 mm Hight of spool: max. 180 mm

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m Lrsdpfx Aisfx Hv Hekel hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Year of construction: 1987, condition: used, sheet width 150 mm coil weight 80 kg coil external diameter 650 mm 1000 mm diameter of the mandrel 230 - 445 mm total power requirement kW Lsdpfsfn Aqlox Aikorl weight of the machine ca. t dimensions of the machine ca. m

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm Lodpfxehlnzks Aiksrl ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Year of construction: 1971, condition: good (used), decoiler - expansion mandrel with coil lifting table Lrodpfsd Ha E Sjx Aiksl strip width: 1.200 mm strip thickness: 0,3 - 5 mm coil weight: 10 t mandrel Ø: 508 mm

Condition: used, Year of construction: 1980, machine/vehicle number: A-07/471A, sheet width - max.:130 mm straightening roll diameter:40 mm :5 :2+2 sheet thickness - min.:0,4 mm Ledpjcxxx Rjfx Aikerl sheet thickness - max.:3,5 mm weight:0,4 t dimensions of the machine ca.:0,6x0,65x1,15 m with integrated, stepless adjustable Vari-drive, reversing, operating-mode switch for manual and automatic operation, introduction roller cage, position indicator of straightening rolls via analogue display, adjustment of straightening rollers via hand wheels, automatic swivel arm control, very good condition

Condition: used, material width 300 mm coil weight 3 t material thickness 2 - 4 mm Straightener, 7 rolls, Make. Schleicher, Type RM 6-95/160 - band width 300 mm - band thickness 2 – 4 mm - cross cut 1200 mm² - voltage 220/380 V 50 Hz - total power requirement 3,1 kW coiler with press roll, Make Schleicher, Type H-3 - Coil weight 3 t - Band width 400 mm - voltage 220/380 V 50 Hz - total power requirement 3,92 kW Lrsdjcdrmmjpfx Aiksl without control

Year of construction: 1980, condition: used, pressure 80 t throat - mm stroke 50 mm table surface area 875 x 695 mm ram surface 350 x 355 mm ram adjustment 71 mm no. of strokes 30 - 90 Hub/min distance between columns 450 mm weight of the machine ca. 6,2 t dimensions of the machine ca. 2,0 x 2,1 x 3,2 m daylight (stroke down, ram adjustment above) 480 mm Further information: - the machine is currently being a partially overhauled - the machine was re-equipped with the following components: * separate control cabinet with touchscreen including cabling * new painting of the individual components in the dismantled state After the partial overhaul, the machine is safe for manual insertion Ljdpfodlcy Hex Aikjrl open tool, a current UVV test is carried out before delivery and braking time measurement.

Condition: as good as new (ex-display), Year of construction: 2020, pressing force: 160 t, Hydraulic 160 T double cylinder insertion press Double column press- two cylinder press with 160 T capacity at 250 bar. a) idle speed downward 9,8 mm/sec. b) upward speed up to 15,0 mm/sec. c) table size 1500x600x100 mm, height adjustable d) ram plate, 1500x600x100 mm e) year of construction 12/2020 f) motor power 11 KW g) pump capacity 22 L/minute h) travel limitation by cam switch i) Open height 700 mm j) ram travel 500 mm k) Remote control via two-hand operation l) Pressure setting via rotary control from approx. 30 to 160 T Lredjgz H Dhepfx Aikjl m) Approx. height 2800 mm n) T-slots according to customer requirements o) Weight approx. 4,200 kg p) Oil tank with approx. 200 L volume q) Painting in RAL 5005 ( royal blue ) or according to customer's request. r) For safety reasons the ram plate is painted orange RAL 2009 or signal yellow RAL 1023 s) Assembly, commissioning, instruction can be provided at a separate charge. The travel can be adjusted by cam switches. The ram/table size of the machine shown is 1600x600x100 mm.

Condition: excellent (used), Lightly used automatic TC, TU, TZ profile production lines, designed for manufacturing and roll forming TC, TU, TZ profiles up to 1.5 mm metal thickness. Technical Specification: Manufactured in: Estonia Adjustable profile height: 100 – 250 mm Lrsdex Sx R Sopfx Aikjl Profile width: 50 mm Profile edge (folded): 15 mm Minimum rollable sheet thickness: 1 mm Maximum rollable sheet thickness: 1.5 mm Roll distance: 300 mm Machine dimensions: 900 x 4000 mm The machine is not equipped with a guillotine or perforating rolls. Operation is straightforward, controlled via two buttons. If you have further questions, we will be happy to answer them.