Ring bending machine

AYEL-TECH PK 40

Year of construction: 2021, condition: new, AYEL-TECH PROFILE ROLLER TYPE PK 40 - Axle diameter 40 mm Ncjdpfx Aogg Rcfokqer - Horizontal/vertical use - Foot-operated - Emergency stop - With 1 set standard steel rollers - With 1 set of plastic rollers for pipe - Documentation - 230V CALL FOR MORE INFO DUTCHMACH Metalworking machines ENSCHEDE

Condition: new, plate thickness 1,2 mm roll diameter 62 mm throat 100 mm total power requirement 0,75 kW weight of the machine ca. 130 kg dimensions of the machine ca. 1,1 x 0,5 x 1,3 m Ncsdpsfv H Edefx Akqsr Flanging machine is equipped with: - Emergency switch - Footswitch - 7 pcs. Roll sets

Condition: good (used), Year of construction: 2019, machine/vehicle number: 24451.19, Offer 25359 Technical Data: - Cutting capacity at 90° (round): 250 mm - Cutting capacity at 90° (flat): 275 x 180 mm - Miter adjustment to the left - Cutting capacity at 45° (round): 200 mm - Cutting capacity at 45° (flat): 190 x 180 mm - Cutting capacity at 30° (flat): 130 x 110 mm - Material support height: approx. 920 mm - Saw band dimensions: 3100 x 27 x 0.9 mm - Infinitely variable cutting speed: 15 to 100 m/min - Hydraulic lifting and lowering of the saw frame - Upper travel limit of the saw frame - Infinitely adjustable cutting pressure: 0 – 10 m/min - Hydraulic material vice - Micro-spray cooling system - Total drive power: 400 V / 2.2 kW - Required space approx.: W 2400 x H 1600 x D 1800 mm Ncsdpfx Aoxup Rfokqjr - Weight approx.: 1300 kg - 3 x Roller conveyor, each 1500 mm

Condition: excellent (used), Year of construction: 2003, The machine has very few working hours and has been in storage for many years) Performance: Hole diameter and thickness up to max.: approx. 28×13 mm Angle steel 90 degrees up to max.: 80x80x8 mm Ncedpfx Aeupzf Rjkqer Angle 100x 100 x 10 Flat steel up to max.: 300 x10/ 200×13 mm (See also rating plate in the appendix). Machine weight: approx. 750 kg Various punches are also included with the machine

Condition: ready for operation (used), Sell due to new acquisition good condition Mikron VC 1000 milling machine Ncodpfeh Tnpxjx Akqer

Condition: new, Year of construction: 2025, Bending machine ZB 70/2 M - with foot pedal - with standard roller set - two driven shafts - mecanical adjusting of the center roller - working position horizontal and vertical - shafts are supported by conical bearings - slide bars on the slide -support are exchangeable - shaft diameter: 40 mm - roller diameter: - shaft rpm: 8,5 U/min - voltage: 400V 50Hz 3Ph - drivingmotor: 1,1 kW - adjusting way: 120 mm Ncjdpfot Hwfnex Akqor - weight: 400 kg - dimensions: 900x600x1100 mm

Condition: new, cutting diameter 235 mm dimensions of saw-band 2645 x 27 x 0,9 mm cutting width 280 x 190 mm cutting speed 45/90 m/min 120 mm 120 mm 190 mm Impact energy 170 mm connected load frequency 400 Volt total power requirement 1,1 kW weight of the machine ca. 290 Kg dimensions 1,2 x 0,8 x 1,2 m Nedop Scqyepfx Akqecr Double miter band saw -Miter cuts up to 60° left and 45° right -Vice with quick clamping device -Band tension control -Electr. Automatic cooling

Condition: new, Ostas 4-roll round bending machine 4R OHS 2070 x 220 Hydraulic side roller infeed Hydraulic folding bearing Hardened rolls Conical bending device Separate control panel Roller length : 2000 mm Top roller diameter : 220 mm Side roller diameter : 180 mm Total motor power : 4+3 KW Weight : 4900 kg Dimensions (mm) : 4050 x 1550 x 1470 (L x W x H) Performance data bending: 11 mm with smallest inner diameter (5 x top roll) 9 mm with smallest inner diameter (1.5 x top roller) Bending performance data: 9 mm with smallest inside diameter ( 5 x top roller ) 7 mm for the smallest inside diameter (1.5 x top roller) Ncodstvn D Tepfx Akqer All bending capacities are calculated on the basis of 250 N/mm2 yield strength Material ( ST 37 - ST 42 structural steel ) Special accessories installed: Infinitely variable rolling speed: NC control:

Condition: new, Stempel von Wila typ für Trumpf/Safan Darley und alle Abkantpressen verwenden das Wila-Klemmensystem Ncjdpfxer Akraj Akqer

Condition: new, Tubend hydraulic profile ring bending machine HPK 50 3 driven rollers Digital display Incl. standard roller set steel Hydraulic / motorized ring bending machine Can be used horizontally and vertically with 3 driven rollers 3 motor-driven rollers Hydraulic infeed of the top roller Nsdpfxjum R U Ae Akqjcr Hydraulic: 8 tons Rollers are hardened Left/right rotation via foot pedal Mounting: shaft 50 mm Roller Ø 162 mm Speed: 4.5 m/min Motor power: 1.1 kW Electrical connection 400 V According to CE standard Weight 510 kg L.W.H. 810 x 950 x 1500mm Power table see PDF file