Used lowboy semi-trailers / low loaders for sale (187)

Condition: new, maximum load weight: 36,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including immediately and soon-to-be available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. - Gooseneck in SNT design to optimize load platform length, approx. 3,700 mm long, with a rear taper approx. 1,000 mm x 6° - For tractors: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic power pack for hydraulic operations (excluding hydraulic winches). Without supply line installation on the tractor unit - Outer beams of the gooseneck with mounting holes for boltable lashing rings. First hole approx. 200 mm from the front, subsequent holes approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper part of the gooseneck’s outer beams for a boltable lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the gooseneck’s outer beams (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) - Grating covering on the gooseneck and rear taper with 5 mm steel reinforcement - 2" kingpin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) Lodpsyhkquofx Ahajah - Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit, with plug (NATO-NATO) - 1 pair of detachable aluminum side boards on the gooseneck, approx. 400 mm high, anodized finish CARGO AREA: - Cargo area, approx. 9,600 mm long, with rear taper approx. 900 mm x 6° - Cargo area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg - TPMS (Tire Pressure Monitoring System) according to ECE R 141 - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle with trailing steering. 3rd axle with electromagnetic reverse lock via reverse gear and manual activation - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand of our choice, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank - Continuous grating flooring with approx. 5 mm steel plating for additional reinforcement, designed for point loads: on the lift bed and cargo area - Painted sand coating on the gooseneck cover plates as well as transition areas between neck and lift bed, lift bed and cargo area, and cargo area and ramps - 1 spare wheel mounting bracket under the cargo area to the right in front of the axles - Cut-outs in the outer frame of the cargo area and lift bed for attaching tie-down straps (LC 2,000 daN) - 11 pairs of recessed, fold-out lashing rings in the outer frame of the cargo area (LC 10,000 daN): 3 pairs in the lift bed outer frame, 8 pairs in the cargo area outer frame - 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 3 pairs in the lift bed, 8 pairs in the rear cargo area - Control valves for the hydraulic ramps located on the right side of the vehicle - 1 pair of foldable mechanical rear supports, single-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm Lajdpfx Aswmh H Eohaeh * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard For further information please do not hesitate to contact us

Condition: new, maximum load weight: 44,000 kg, overall weight: 61,000 kg, axle configuration: 3 axles, Year of construction: 2026, Further information here: Lasdpfxov D Abto Ahajh

Condition: new, maximum load weight: 73,540 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Hydraulically extendable/retractable and lowerable gooseneck, length ± 3,650 mm * 2 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the middle section of the gooseneck (LC 10,600 daN) * Suitable for 6 x 4 or 8 x 4 tandem axle vehicles Compact front axle: * Hook receiver at the front and rear, length: approx. 2,200 mm * Axle width: approx. 2,850 mm Excavator bridge: * Telescopic excavator bridge with traversable bridge hooks at the front and pin-and-plate coupling at the rear * Overall width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance approx. 150 mm 4-axle rear axle: * Mechanical pin-and-plate coupling for mounting a low-bed trailer at the front * End crossbeam at the rear, axle width: approx. 2,850 mm * Axle length: approx. 5,480 mm Swivel axles, all axles hydro-mechanically force-locked * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle suspension Tires: * Front axle: * 8 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Rear axle tires: * 16 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Load index 150/148J Painting: * Complete steel construction automatically blasted with a shot blasting system after welding. Second blasting with corundum for optimal adhesion of the coating system. * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection. * Final painting with 2 layers of 2K topcoat, single-color in RAL 3002 carmine red, according to the RAL 841GL system. Including the following accessories: * Steel front panel, approx. 400 mm high * Aluminum side and rear walls, pluggable on the gooseneck, approx. 400 mm high, in anodized finish * 3.5-inch kingpin * Truck hydraulic connection with flow control (20 l/min) * Gantry for suspending the supply lines; the SZM tank must have a minimum capacity of 80 liters. * With MAX Trailer coupling parts; otherwise, coupling parts must be supplied by the customer. Lasdpfx Aexbmplehajh * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Tool kit, type No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front axle with a separate air connection for air suspension * BEKA-MAX central lubrication for a 2-axle axle with standard grease NLGI-2 * One 7-pole socket on the left and right at the rear of the front axle for warning signs * Screw-in option (approx. 40 mm diameter) every approx. 500 mm on the outside of the top chord of the outer beam of the excavator bridge for screw rings (LC 16,000 daN) * Foldable wideners with steel mats, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX central lubrication for a 4-axle axle with standard grease NLGI-2 * On the rear axle, a socket for the cable remote control of the trailing axle * Rear axle with tipper body * Two INOX toolboxes, approx. 855 x 340 x 390 mm, on the gooseneck, left and right * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the power pack, start/stop of the diesel engine

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg Ljdpfx Ahexarl Nsasah - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks

Condition: new, maximum load weight: 29,260 kg, overall weight: 42,000 kg, axle configuration: 3 axles, loading space length: 13,200 mm, loading space height: 900 mm, total width: 2,550 mm, total height: 3,570 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer SLAR3 Tele Lowboy Trailer with Wheel Recesses Technical Data: Model and Manufacturer: Model: Kässbohrer K.SLA R 3 / 1N - 18 / 30 * Manufacturer: Kässbohrer * Type: Extendable, wheel recess lowboy trailer, suitable for the transport of vehicles and heavy machinery. Dimensions: * Overall length: 13,190 mm * Gooseneck length: 3,950 mm * Platform length: 9,240 mm * Extension: 3,500 mm * Overall width: 2,550 mm (expandable by 600 mm via side extensions) * Fifth wheel height: 1,250 mm * Platform height: 875 mm * Ramp length: 2,750 mm * Ramp width: 850 mm * Wheelbase: 7,800 mm * Axle distance: 2,260 mm Weights and Load Capacities: * Permissible total weight: * 52,800 kg at 60 km/h * 48,000 kg at 80 km/h * Tare weight: 12,744 kg ±3% * Axle load capacity: 30,000 kg (10 tons per axle) * Fifth wheel capacity: 18,000 kg Axle Configuration: * Number of axles: 3 (2 fixed axles at the front, 1 trailing axle at the rear) * Lift axle: Manually controlled, load-dependent (1st axle) * Axle material: BPW axles with drum brakes Tires and Rims: * Tire size: 245/70 R17.5 * Tire brand: GOODYEAR * Tire markings: M+S label and 3PMSF marking * Tire pressure monitoring system: Increases fuel efficiency and extends tire life * Number of rims: 12 pieces (steel rims with offset ET120) Chassis and Suspension: * Suspension: Air suspension with load gauge * Braking system: Two-line pneumatic brake system by WABCO, EBS 4S/3M with ABS and RSS (roll stability program) Lighting and Electrical System: * Lighting system: 24V, multi-chamber lights by ASPÖCK, side markers, and rear lights in LED * Coupling type: Standard yellow/red for air supply connection * Connections: NATO socket with 2 x 50mm² intermediate cable (3 m length) Ramps: * Ramp type: Folding hydraulic ramps with sliding mechanism * Capacity: 40 tons * Ramp surface: Made of hardwood * Safety devices: Ramp protection chain included Load Securing: * Tie-down points: * 2 x 2 with a load capacity of 5,000 daN each * 1 x 2 with a load capacity of 10,000 daN on the gooseneck * 4 x 2 tie-down points with a capacity of 6,000 daN in the platform area * Container lock housings: Suitable for the transport of 1 x 20 FT or 1 x 30 FT container * Stake pockets: 5 x 2 stake pockets (50 mm x 100 mm) Special Features: Laodpfx Ahsx Epaqeajh * Gooseneck: With 90° vertical corners, stable and durable * Floor covering: 45 mm thick hardwood floor and steel floor with a drop-pattern structure * Wheel recess bridge: Bridges made of split hardwood pieces with sheet metal supports to cover the wheel recesses * Tool box: PVC-coated steel, dimensions 750 x 400 x 360 mm Colors: * Chassis: Traffic red (RAL 3020) / also available in black * Partial metallization of the support surfaces Condition: New and ready for immediate use. * Perfectly suitable for heavy transport and for use in the construction industry or for relocating machinery.

Condition: new, maximum load weight: 36,040 kg, overall weight: 53,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm * Gooseneck hydraulically raisable/lowerable and extendable * For tractor unit: 6 x 4 or 8 x 4 Low-bed: * Low-bed with external beams in an extendable SUPER LOW design, length approx. 8,000 mm * Low-bed with a fixed hardwood floor approx. 40 mm thick and mechanical locking system * The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length * 7 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 6 pairs of threaded blocks on the inner beam for mounting screw-on RUD rings Rear chassis: * Rear chassis with closed outer frame and diamond plate cover * Chassis with excavator bucket, which is closed in the rear half to accommodate the air tanks * 3 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 1 pair of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally, at the front and rear of the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires: * Tires 245/70 R 17.5 3PMSF - at the manufacturer's choice. Load index (146/146F) Braking system: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paint: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Topcoat with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system Includes accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high Lajdpfjy Uwu Iex Ahaoh * Yellow-red air couplings on the galvanized connection strip at the front * Trailer steering, operable from the front and rear via cable remote control with push buttons, with single-axle steering control (without installation in the tractor unit) * Preparation for mounting screw-on container positioning for 1 x 20', 1 x 40' or 1 x 45' containers on the outer beams. Without container locking mechanisms * Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw couplings * Electro-hydraulic unit * Spiral cable for supplying the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with plug connection (NATO-NATO) * Yellow reflector tape according to EU regulations on the side, on the extension and at the rear of the semi-trailer * On the gooseneck and at the rear, left and right, one bracket each for the warning signs, including a socket * Manual and description on a USB stick * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pumps * 7 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD VLBG-4 rings * 2nd driving height, approx. 50 mm above the normal driving position, by means of manual operation * On the gooseneck, plug-in aluminum side panels and rear panel, approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in frames are removable (length of the superstructure

Condition: new, maximum load weight: 48,930 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck * with beveled front corners, approximately 45° and with rear bevel approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick Loading platform * in a double-extendable design with rear bevel approximately 500 mm x 8° * 5 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 4 pairs of lashing rings, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally at the front of the loading platform (LC 10,000 daN) * 1 intermediate table, approximately 250 mm * Recesses in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, with diamond plate flooring over the axles Axles * BPW axles, hydro-mechanically forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires * 245/70 R 17.5 3PMSF, load index (146/146 F) * TPMS tire pressure monitoring system according to ECE R 141 Kingpin * JOST kingpins (mechanical) with a 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Braking system * according to EU regulations with EBS-E (4S3M) Laodjzlwm Aopfx Ahajh Steel structure * made of high-strength fine-grained steel * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) * S690QL/S700MC (yield strength 690 MPa) Electrical system * according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the turn signal * ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Painting * Complete steel structure automatically blasted after welding using a blasting wheel system * Second blasting with corundum for optimal adhesion of the coating system * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Final coating with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system * Rims in silver. Rear part metallized and painted in RAL 9010 (pure white) * Metallic paint is not possible * Paint structure tested in the salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Including the following additional equipment 2 inch kingpin * Electro-hydraulic unit (± 45 kg) * Follow-up steering from the front and rear, controllable by means of a cable remote control via push buttons, with single-axle control (without installation in the central control unit) * One bracket for warning signs on the left and right of the gooseneck and on the rear panel, including socket * One bracket for a rotating beacon on the rear of the trailer * Aluminum side panels and rear panel on the gooseneck, pluggable, approximately 2,440 x 400 mm (L x H) * The rear galvanized stake pockets are removable. (Length of the superstructure approximately 2,560 mm) (± 46 kg) * A tool box, galvanized, integrated into the beveled gooseneck (± 47 kg) * 4 pairs of WADER container pockets in the loading platform for a 20', 2x 20', 40 or a 45' container (± 40 kg) * 7 pairs of stake pocket for stake pockets approximately 100 x 50 mm in the outer frame of the loading platform (± 21 kg) * Extensions, galvanized

Condition: new, maximum load weight: 25,300 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment details. Full specifications available upon request. Neck (Gooseneck) * Gooseneck in SNT design to optimize loading platform length * Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2 Kessel Bridge (Tiefbett section) * Low bed designed as extendable Kessel bridge in SUPER LOW design * Approx. 6,850 mm length * With mechanical locking * Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length Rear Chassis * Short version with closed outer frame and checker plate cover * Chassis with excavator trough, closed at the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve Tires * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Brake system * Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit Paintwork * 6-Coat final treatment * All-steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver grey * Drop side color: Natural aluminum Accessories included * Removable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit * Spare wheel carrier in front of the gooseneck front wall * Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN) * 2" king pin * Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly * Air connection with air gun at the gooseneck Laodpfev Sw E Ajx Ahajh * 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Outer side beams of the loading area prepared for removable loading floor * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN) * Cut-outs above the lashing rings in the outer carrier’s upper flange * Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings * The outer carriers of the low bed coated with anti-slip sand finish for slip resistance * 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit * 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Front and rear tapers

Condition: new, empty load weight: 5,500 kg, overall weight: 19,500 kg, axle configuration: 1 axle, loading space length: 11,800 mm, loading space width: 2,550 mm, loading space height: 1,100 mm, suspension: air, tire size: 215 75 17,5, Equipment: crane, 1x SAF or BPW axle Total weight: 19,500 kg Payload: 14,000 kg Empty weight: 5,500 kg Total length: 12,800mm + 1500mm Brake system: Wabco 2S-2M Electrical system: Aspöck Systems Air suspension Hydraulic rear extension in full width 2550mm and length 1500mm Semi-trailer completely galvanized / galvanized (100% galvanized / 100% galvanized) Tire size: 215/70 R 17.5 Tire brands: Pirelli, Goodyear, Fulda, Continental. 5th Wheel Height: approx. 1050mm - 1150mm (other saddle heights also possible) Hydraulic winch 8ton with remote control with pulleys 24v 4.5KW electro-hydraulic motor Laodpfekqmuusx Ahajh Steel ramp: 2 pieces Changes possible according to customer requirements Painting freely selectable / free of charge All documents COC, Tüv, etc. available for approval.

Condition: new, empty load weight: 10,400 kg, maximum load weight: 45,600 kg, overall weight: 56,000 kg, axle configuration: 3 axles, loading space length: 8,600 mm, loading space width: 2,550 mm, loading space height: 1,000 mm, suspension: air, tire size: 235/75R17.5, color: green, Year of construction: 2021, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 3 axles, air suspension, ABS (anti-lock braking system), extendable to 3m, hydraulic ramps, rear support, supports. Body: 3-axle low-loader trailer with hydraulic loading ramps, 3 x 12t axles, drum brakes, loading height approx. 1030 mm, extendable to 3m, hydraulic ramps operated via its own electric pump! Independent hydraulic pump with electric motor, independent from the tractor unit, gooseneck length approx. 4m, low bed length approx. 8.6m! New vehicle from stock! Lsdpew Rf N Defx Ahaoah EU type approval currently under review! ACCESSORY INFORMATION PROVIDED WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted!

Condition: new, functionality: fully functional, Year of construction: 2026, Equipment: ABS, EBS, 2+1 Axle Platform Trailer Ledpfxsyaxthj Ahajah

Condition: new, axle configuration: 3 axles, Year of construction: 2026, We have all Europe documents!   Ljdjqx Nfgopfx Ahajah    We can delivery the trailers with FOB-EXW-CPT-CFR-CIF      If you have an interest please contact with us 

Condition: new, overall weight: 32,000 kg, axle configuration: 2 axles, loading space length: 12,300 mm, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Wiese 2-axle stepped saddle plateau with Fassi F545 crane Mega Lowliner Chassis Welded construction with cross beams made entirely of high-quality steel Neck height = approx. 220 mm including coupling plate with all necessary chassis reinforcements and cross connections Axles 2 BPW axles with a load capacity of 10,000 kg each with 17.5" drum brakes ABS: 1 axle sensing Wheelbase: 1,810 mm Tires 8-wheel type 235/75 R17.5 Rims Aluminum rims, 10-hole, centered, ET= 122 mm Lighting system 24V lighting system in accordance with EU directives 76/756/EEC ff. with: 2x2 three-chamber LED lights 1x reversing light LED 1x LED fog light LED side marker lights Lane departure lights License plate illumination 2x 7-pin sockets + 1x 15-pin socket connected according to EU standard Floor Galvanized grating covering on drop deck Steel tear plate in the axle area Load securing Outer frame with lashing hole profile D030 mm in the slope 2x12 lashing points 8,000 daN in the outer frame 3x combi row of stanchion pockets for 80x80 mm stanchions in the drop deck Accessories 2x wheel chocks with holder Spare wheel holder Winch 2x storage box with drawer (chain storage) Surface protection Steel construction: blasted and primed Coloring Chassis/frame/floor frame: single color in RAL 3020 (traffic red) Axle hubs: single-colored in RAL 3020 (traffic red) Lajdpfjt Izpyox Ahaoh Axles: KTL-coated black Rims: Aluminum Durabright With Fassi F 545 RA.2.28 XE-Dynamic Hydraulic outriggers Additional support beam 360 ° working range approx. 90 % to the front For further information please do not hesitate to contact us

Condition: new, overall weight: 36,000 kg, loading space length: 13,300 mm, loading space width: 1,640 mm, loading space height: 3,770 mm, Year of construction: 2026, Equipment: ABS, Special vehicle for forklift transport. In-loader / intermediate loader for max. internal height of approx. 3,770 mm Offer price without optional equipment. Available equipment: Rear with loading lift / elevator suitable for loading and unloading on ramps. The vehicle is currently being manufactured and has a delivery time. On request, we will be happy to make you an offer with the desired equipment. For more information, please visit: Laedpfx Asvw Hm Tshaoh or call us.

Condition: new, maximum load weight: 31,400 kg, overall weight: 45,000 kg, axle configuration: 2 axles, loading space length: 6,800 mm, loading space width: 2,550 mm, total width: 2,550 mm, total height: 300 mm, Year of construction: 2026, Equipment: ABS, DOLL NEXT DOLL NEXTLowbed tera T2P-S3FS21 – 2-axle lowboy trailer from the rapidly available rapid series by DOLL Fahrzeugbau GmbH, Oppenau – straight from the heart of the Black Forest. Ideal for demanding applications in tough off-road environments, challenging terrain, and for daily use on construction sites. Depending on availability, very fast delivery and operational readiness thanks to DOLL's rapid series production. Individually configurable according to your specific requirements and wishes. Technical Data * Permissible Gross Weight: 45,000 kg Ledpfx Aheyytm Rjasah * Unladen Weight: approx. 13,600 kg * Payload: approx. 31,400 kg * Running gear: 2 x 12t pendulum axles * Extendable lowbed * Vehicle width: 2,550 mm * Load height (loaded): 300 mm * Wheelbase: 1,360 mm Equipment Features * Detachable gooseneck for significantly easier and faster loading and unloading * Smooth telescoping for efficient handling * High-quality spray galvanization for optimal corrosion protection and reduced downtime * Powder-coated and hot-dip galvanized attachments: robust and durable – no rust Your Key Benefits at a Glance * Rapid availability * Robust & reliable – proven technology, ideal even in demanding conditions * Made in Germany – manufactured by DOLL Fahrzeugbau GmbH in Oppenau, a company with over 145 years of experience in premium vehicle engineering Smart Technologies Our innovative approach combines quality, performance, and cost-effectiveness at the highest level. The rising demand for our lowbed semi-trailers drives the continuous development of state-of-the-art technologies in series production. Contact & Location Manufactured by DOLL Fahrzeugbau GmbH, Industriestraße 13, 77728 Oppenau (headquarters and production site) * The vehicles can be demonstrated either at the factory or at selected reference customers across Germany, together with one of our field sales representatives, depending on customer location.

Condition: new, maximum load weight: 35,800 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Lasdpfsz Dmnwjx Ahajh Excerpt from the equipment. Complete equipment available upon request. Chassis, gooseneck: Special steel frame made of high-strength fine-grain steels, electrically welded at the connection points, well-dimensioned outer frame. 3-axle arrangement. Wheel arch above the axles with spray mist suppression. All steel parts sandblasted. Lateral impact protection made of anodized aluminum mounted. Increased point load of approx. 30,000 kg over approx. 5,000 mm. Special design in the gooseneck area for maximum possible low-bed length in combination with the AluLeg outrigger supports, instead of telescopic outrigger winches, max. rear pivoting radius of the semi-trailer tractor unit 2,100 mm. Special superstructure with rear girder widening: DINKEL - special superstructure. Self-supporting aluminum roof beam / profile approx. 100 x 100 mm, sliding tarpaulin with plastic flaps. Rear girders can be widened to approx. 4,200 mm (only for loading and unloading). Three sliding girders per side with rubber strap relief. Additional center girder locking in the roof beam and parking position, by means of a pull cable and spring latch. DINKEL - lifting roof, mechanically height-adjustable. Lifting roof height approx. 400 mm, operable on both sides or on one side. Without opening the opposite side and the doors. Additional height adjustment of approx. 480 mm in approx. 40 mm increments, with height adjustment in the girders. Front cover on the front wall for operation under a tarpaulin up to a total height of 4,400 mm. Four rows of stackable approx. 150 mm aluminum slats on the side, with 450 mm pockets at the bottom, above 4 rows of individual pockets. In the upper bed, only 3 rows of insert slats. Evenly distributed spacing. Floor: approx. 27 mm special water-resistant glued beech - screen-printing panels, rough surface. Steel sheet in the wheel arch area. Forklift-compatible according to DIN standard. Outer frame flush with the surface. Brakes: WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (parking/release safety valve). Spring brake cylinders as parking brake. Wabco Smart Board with odometer and unit load display. Including WABCO tire pressure monitoring system. Axles: 3 x 10,000 kg SAF/Sauer with drum brakes in a low-bed design. Air suspension with lifting and lowering device, total stroke approx. 230 mm. Third axle as a friction-controlled trailing axle with electric and mechanical lock. Twin tires: 235/75 R 17.5, -12-ply. Premium brand of our choice, including E-wheel chocks. Lighting: according to EC standard including side lights in LED design. Position lights in LED design. 2 additional reversing lights. 2 work lights on the front wall inside, top. Painting: Chassis with superstructure in RAL color of your choice. Center girders, axles powder-coated black. Corner girders in hot-dip galvanized design. Plastic parts black. Hot-dip galvanized parts unpainted. Rims in factory silver. Special equipment including: - E-supply line 15-pin - Air suspension in ECAS design, operation on the semi-trailer - Overwidth signs front and rear in galvanized, steplessly telescopic design with attached marker lights including sockets for flashing beacons (small signs) - Center girders with additional roof beam locking, by means of a pull cable - operation from below - Sliding tarpaulin support unlocking also from

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm Ljdpfx Aow Ii A Ajhaeah * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard For further information please do not hesitate to contact us

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm Lasdpfx Ahsw Nlzqjajh * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard For further information please do not hesitate to contact us

Condition: new, overall weight: 31,000 kg, loading space length: 13,600 mm, loading space width: 2,480 mm, loading space height: 3,300 mm, Year of construction: 2026, Equipment: ABS, 2-axle inclined semi-trailer in special design with loading ramp for machine and forklift transport. Mega design with a coupling height of approx. 960 mm. Tapered construction for maximum internal height. Dimensions: Length: 13,600 mm Width: 2,480 mm Height, tapered from rear to front: approx. 3,300 mm to 2,800 mm Wheel recesses including fill-in pieces VSE Smart Steering axle (steers forwards and backwards) Aluminum floor for extreme wheel loads, including anti-slip coating Alcoa DB alloy wheels on the outside Curtainsider body with lifting roof Lodjx Hb Rdjpfx Ahaeah RSAB IceProtect Rear extendable Oversize warning plates Rear ramp in extendable version for minimum approach angle, including angle reduction Electro-hydraulic drive Comprehensive load securing equipment Upon request, we also supply the appropriate 3-axle tractor unit for purchase or rent. Further information available on request.

Condition: new, maximum load weight: 44,400 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,500 mm, loading space width: 2,550 mm, total width: 2,550 mm, total height: 300 mm, Year of construction: 2026, Equipment: ABS, DOLL NEXT DOLL NEXTTiefbett tera T3P-S3FS25 – 3-axle low-bed trailer from the rapid series by DOLL Fahrzeugbau GmbH, Oppenau – in the heart of the Black Forest. Ideal for demanding applications in tough off-road conditions, challenging terrain, and daily use on construction sites. Thanks to DOLL rapid-series manufacturing, the trailer is available at very short notice and ready for operation, subject to availability. Can be individually configured to meet your specific requirements. Technical Data * Permissible gross weight: 61,000 kg * Unladen weight: approx. 16,600 kg | Payload: approx. 44,400 kg * Chassis: 3 x 12 t pendulum axles * Extendable low-bed * Vehicle width: 2,550 mm * Loading height (loaded): 300 mm * Wheelbase: 1,360 mm Features * Removable gooseneck for significantly easier and faster loading and unloading * Smooth telescoping for efficient handling * High-quality hot-spray galvanizing for optimal corrosion protection and reduced downtime * Powder-coated and hot-dip galvanized add-on components – robust and long-lasting – rust-free Your Advantages at a Glance * Rapid availability * Robust & reliable – proven technology, ideal even under the most demanding conditions * Made in Germany – manufactured by DOLL Fahrzeugbau, Oppenau – over 145 years of experience in premium vehicle manufacturing Smart Technologies Ledpeyytnbjfx Ahaoah Our innovative approach combines top-level quality, performance, and cost efficiency. The steadily increasing demand for our low-bed semi-trailers is driving further development and implementation of cutting-edge technologies in series production. Contact & Location Manufactured by DOLL Fahrzeugbau GmbH, Industriestraße 13, 77728 Oppenau (headquarters and production site) * Depending on customer location, the vehicles can be demonstrated directly at the factory or, in cooperation with our field sales team, at selected reference customers across Germany.

Condition: new, Year of construction: 2026, Equipment: ABS, 5 Axle Lowbed Laodsrlm Txopfx Ahajh Please get contact with us for more informaiton;

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners Ljdpfx Ajyhi H Iehaeah * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard For further information please do not hesitate to contact us

Condition: new, maximum load weight: 31,500 kg, overall weight: 42,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, Wiese 3-axle semi-trailer with lift table and fold-down rear. Ideal for transporting forklift trucks and/or work platforms. Lasdpfx Ahsvw Hmteaoh Technical data. 3 x 10 to. axles Lift axle Steering axle Smart Steering (steers forwards and backwards) Outer beam chassis with slope 18-tonne neck design suitable for 2- and 3-axle semitrailer tractors Lifting table hydraulically movable in 3 positions Rear in folding rear design incl. hydraulic extensions, can be used as drive-on ramps, drive-over ramps or as a loading area (overall length reduction when rear is raised) Remote control for ramps and lift table Front wall Grid floor Numerous lashing points SmartBoard Central lubrication system Spray-galvanized and painted steel construction Numerous optional extras are available: e.g: Cable winch Storage box on the saddle step aluminum rims Further information on request.

Condition: new, overall weight: 32,000 kg, axle configuration: 2 axles, loading space length: 12,300 mm, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Wiese 2-Axle Step Frame Semi-Trailer in extendable version with Fassi Crane F545RA.2.26 Mega Lowliner as step frame semi-trailer. Chassis Welded construction with cross members, made entirely from high-quality steel Neck construction reinforced for front-mounted crane Axles 2 BPW axles, each with 10,000 kg load capacity, 17.5" drum brakes ABS: 1 axle sensor-controlled Axle spacing: 1,810 mm Both axles equipped with forced steering Tyres 8x type 235/75 R17.5 Rims Aluminum rims, 10-hole, hub-centric, ET=122 mm offset Lighting system 24V lighting system compliant with EU Directives 76/756/EWG and following, with: 2x2 three-chamber LED taillights 1x LED reversing light 1x LED fog light LED side marker lights Lane keeping lamps License plate illumination 2x 7-pin sockets + 1x 15-pin socket wired according to EU standard Floor Anti-slip birch plywood flooring Steel checker plate above axle area Load securing Outer frame with lashing hole profile D030 mm on inclined edge 2x12 lashing points 8,000 daN in outer frame 3x rows of combination pin stake pockets for 80x80 mm stakes in the low bed Accessories 2x wheel chocks with holders Spare wheel holder with winch 2x storage boxes with sliding compartment (for chain storage), etc. Crane: Fassi F 545 RA.2.26 XE-Dynamic Hydraulic outriggers Additional outrigger beams 360° working area Approx. 100% outreach forward Lodpfx Asyihgyshajah The attached images are sample images. We manufacture crane semi-trailers in various versions. For further information, we are at your disposal. Upon request, we will provide you with a customised quotation tailored to your equipment requirements.