UV dryer for moldings and profiled timber

Cefla TLFP

Condition: excellent (used), Year of construction: 2015, I sell the 2-head UV-drying tunnel Superfici Essiccatoio UV Model: Poliedra S.Cure 1650x2 + TT1 3500. Year 2015. Available immediately. Knsdpsffk Etsfx Ahajc Repairs needed: Display, Energy power units for each two UV-units

Condition: used, Tool grinding machine, twist drill grinding machine BORA -- BI-EMME s.n.c. (Italy) Type 1/BM 40 No. 49697 Year of manufacture 1997 Grinding range Ø 3 - 40 mm Center angle 40° - 180 Motor power 1.1 kW Grinding wheel dimension max. Ø 200 mm Grinding wheel speed 2840 rpm Mains connection 400 Volt, 50 Hz - For grinding standard drills and other tools with 1, 2, 3, 4 or 6 cutting edges (step drills, taps, countersinks, drills with a thick core and drills with special grinding) - Precision six-jaw chuck Ø 125 m - pointing device (motor power 0.18 kW) - For left and right cutting drilling tools thanks to interchangeable cams Kodenzt A Hjpfx Ahaenc - Cam disks easily interchangeable for 2 or multi-bladed tools - 4 cam disks - Centering arbor for MK1, MK2, MK3, MK4 - A white grinding wheel with a diameter of 170 mm and a width of 40 mm is installed - Metal base with door and shelf - Wet grinding unit shown opposite - Operating instructions per PDF Space requirement L x W x H 900 x 850 x 1250 mm Weight 220 kg Very good condition

Condition: good (used), Clean air extraction system Used machine, in good condition Images to follow mobil Jet 160, Connection 160, Fan 2.2 kW Knsdpfxsrb D No Ahaec Air flow rate 1850 m³/h, 400 V

Year of construction: 2016, condition: excellent (used), Painting booth Diana serie with horizontal ventilation Modern technology: Kodpfx Aoygum Rohajnc Dust free operation paint overspray collection system Stable spraying temprature Control box with safety function Length:16000mm Width:6000mm Height:6000mm

Year of construction: 2016, condition: excellent (used), - (dust-free operation, paint overspray collection system, stable spraying temperature, elevated drying temperature) Control box including advanced safety functions and operator-friendly software- (weather condition independent operation, elevated temperature in the drying phase)- (daylight-grade illumination, fire safety, efficient ventilation rendering operator's individual respiratory protection equipment redundant)- Low operation cost : (reduced operating costs owing recirculation of warm air in the drying phase)- (efficient dust collection, low solvent vapor concentration, low air pollutant emission)- Limited operating area requirement : (minimized production area) Length:16000mm Width:6000mm Height:6000mm Kjdpfx Aoygu Smehaenc

Condition: new, Year of construction: 2026, CNC drilling and dowel insertion center for doors (rails and stiles) and window components for a rational and professional production of doweled frames. Short introduction: • Universal CNC controlled drilling and dowel inserting machine for door stiles and rails as well as for window profile processing • Glue shot monitoring via GIC • Closed gluing system Knedpfxedx R A Uj Ahaoc • Optional, additional horizontal drilling spindles • Relieves CNC machining centers

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. Kodpfx Aswzl Hxjhaonc * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: good (used), UV dryer, UV lamp, high-performance UV lamp -the lamps come from a UV paint drying process -Working width: 1400 mm -Double housing -UV range: 180 - 450 nm -UV tube type: CK 110/80 - Radiator power: 80 W/cm² -Quantity: 3x dryer lamps, each with 2 tubes included Price: per piece -Transformers and accessories: available at extra cost (2x ID13948 and 2x ID13949 or ID13950) -Dimensions: 1720/400/H630 mm -Weight: 126 kg/piece Knedpjcft T Hjfx Ahasc

Condition: used, Year of construction: 2002, UV dryer, Cefla UV 2000 - Manufacturer Cefla/Sorbini - Type UV 2000 M2 / TN3000 - Year of manufacture 2003 - Working width 1.300 mm (1.445) mm - Working height 900 + - 40 mm - Operating side right - Max. part height 70 mm - Number of tubes from above 2 pcs. - diagonally positioned tubes 2 pcs. - Suitable for mercury tubes - Suitable for gallium tubes - Tube power max. 120 W/cm - with belt transport - Length 3.000 mm - Width 2.300 mm - Height 1.500 mm - Volts, Hz 400 /50 - Total electrical connection 86 A / 36.4 kW Kodpfx Aeyifwpohaonc - Voltage fluctuations max. +/- 5%

Condition: excellent (used), Machine suitable for the polishing and the cleaning process (top & bottom) of panels. - Upper cleaning system (with 2 motorized rubbered cross belts with brushes) Motor power: Kw 0.19 - Lower cleaning system (with 2 motorized rubbered cross belts with brushes) Kjdpfx Aheyw Rpqjaonc Motor power: Kw 0.19 - Max working width mm 1500 ca.