Hydr. pressbrake

ERMAK SPEED BEND PRO 4.320

Condition: used, Year of construction: 2013, pressure 320 t chamfer lenght 4100 mm distance between columns 3600 mm column arm 410 mm ram stroke speed 140 mm/sec work speed 10,5 mm/sec return speed 150 mm/sec work stroke 375 mm Gbodpsz I Dz Ajfx Al Usu dayligth 650 mm table height 900 mm table width 220 mm oil volume 400 ltr. voltage 380 Volt total power requirement 30.0 kW weight 21300 kg range L-W-H 5350 x 2450 x 3150 mm Features: - DELEM DA66T CNC control system - CNC-controlled axes: Y1, Y2, X, R, Z1, and Z2, as well as CNC crowning - FIESSLER AKAS laser safety device in front of the machine (including FPSC) - Rear safety device: light barrier - BOSCH/HOERBIGER hydraulic components - SIEMENS electrical components - 2 front support arms - 1 freely movable dual foot control - Upper and lower tools

Year of construction: 2026, condition: new, The fruit washer with a mill for fruits and vegetables is made entirely of stainless steel and is equipped with a sorting grate, a washing tank, and a conveyor belt. The fruits are immersed in water for a pre-wash. Afterwards, they are transported further via the conveyor belt, which thoroughly cleans the fruits with fresh water. After cleaning, the fruits enter the mill, where they are processed with the desired sieve to achieve the required mash consistency. Gbedpfev Srguex Al Uou • Easy to clean • Low maintenance requirements • Belt speed is steplessly adjustable in both directions • Equipped with 2 swivel wheels • Equipped with 2 fixed wheels Technical Information • Nominal capacity: 2000 kg/h • Power requirement: 3 kW, 400 V, 10 A • Mash discharge height: 1400 mm • Connection for washing tank: G 6/4” • Connection for cleaning: G ½” • Material: WNr. 1.4301, AISI 304 stainless steel • Water consumption: approx. 12 L/min Dimensions: Length: 2700 mm Width: 840 mm Height: 2270 mm Weight: 150 kg

Condition: good (used), functionality: fully functional, stroke length: 300 mm, throat depth: 450 mm, controller manufacturer: Delem, controller model: DA65, working width: 4,300 mm, bending force (max.): 300 t, distance between stands: 3,700 mm, control type: CNC control, number of support arms: 2, number of axes: 4, type of crowning: CNC-controlled, actuation type: hydraulic, Equipment: CE marking, centralized greasing system, documentation/manual, emergency stop, finger protection, foot remote control, lower tooling, safety light barrier, upper tooling, Bending capacity: 300 Ton Bending length: 4.300 mm Distance between columns: 3.700 mm Back gauge: 550 mm Stroke length: 300 mm Throat: 450 mm Rapid approach speed: 120 mm/sec. Bending speed: 10 mm/sec. Return speed: 120 mm/sec. Controller: Delem DA65 Featured with: - Y1, Y2, X & R-axis controlled - CNC Hydraulic crowning - Various sets of bending tools - Laser safe curtain Lazer Safe - Machine manual and documentation Country of origin: The Netherlands Motor power: 30 kW Machine LxWxH: 510 x 200 x 330 cm Gbedpfxjydpxvs Al Ueu Machine weight: 21.500 kg

Condition: new, Year of construction: 2026, table length 3048 mm table width 1524 mm burner heads 1 Control CNC workpiece weight 911 kg traversing speed 180 m/min weight 4150 kg dimensions of the machine ca. 9392 x 2232 x 2307 mm Laser cutting machine with automatic shuttle table Configuration 1. Bodor Power 3kW laser source 2. Bodor Genius laser cutting head with autofocus 3. Bodor Thinker 3.0 control system 4. Mortise-and-tenon type plate welded segmented bed 5. Stretched aluminum gantry 6. Bodor servo motor and driver 7. Bodor rack and pinion 8. One-click processing 9. Bodor Lightning perforation technology 10. Expert database for high-speed cutting 11. Automatic cutting gas pressure adjustment 12. Open door protection 13. Cutting malfunction alarm function 14. Ergonomic remote control (Bodor Mango®) 15. Active anti-collision function 16. Intelligent anti-shake 17. Gas-saving continuous flow nozzle 18. Intelligent maintenance reminder 19. WIFI internet connection 20. Water cooler 21. Extraction system Gedswnt Eijpfx Al Uobu 22. Wear parts set CUTTING CAPACITY: STRUCTURAL STEEL 14 mm STAINLESS STEEL 10 mm ALUMINUM 6 mm OPTIONAL: LANTEK EXPERT II CUT software incl. postprocessor Translated with (free version)

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Gedpfx Alsfz U S Es Usbu Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Condition: refurbished (used), Year of construction: 2024, Overhauled: 2024 Control: SPS Siemens S7 Saw blade max: 500 mm motor power 4,0 KW Saw blade feed: 0-40 mm/ s continuously adjustable Saw height control electronic Working range square 90° max.: 130 x 130 mm Working range flat 90° max.: 190 x 130 mm Working range round 90° max.: 170 mm The machine has been completely overhauled in our company and is in mint condition. Among other things, the following points were renewed: Conversion to Siemens S7 PLC control Godpfx Asuiy Ngjl Usbu Conversion to Siemens HMI user interface Conversion to pusher with servo control New electrical components New pneumatic lines New pneumatic components Conversion to valve terminal Optimization of the suction capacity New minimum lubrication system Replacement of general wear parts Overhaul of the cab The machine also has Minimum quantity lubrication Splitting extension (for a high-quality cutting surface without return marks) Pre-loading magazine for gentle handling of painted/anodized surfaces Offcut ejector in the pusher Foldable offcut tray Optional: Magazine width 3000mm Pusher length 6000mm Pusher length 8000mm Reinforced motor 5.5 kW Mass clamping device for parallel sawing of several workpieces Online support connection Delivery and installation on your premises Training of your employees

Year of construction: 2019, condition: new, Recirculating air convection furnace Gas-fired furnace CGN Powder coating oven NEW – SGS-800/O Gema Optiflex Width: 2500 mm, Height: 2500 mm, Depth: 12500 mm Directly from the manufacturer. For more information, visit Gjdpfx Alocw Tzxe Uobu Romer-Deutschland.

Condition: good (used), Year of construction: 1991, pressure 300 t chamfer lenght 4100 mm distance between columns 3710 mm stroke - stepless adjustable 250 mm column arm 330 mm dayligth 500 mm table height 940 mm table width 250 mm working feed 7.0 mm/sec return speed 90.0 mm/sec Control konv. operating pressure max. 305 bar voltage 380 V total power requirement 22.5 kW weight 25200 kg range L-W-H 4320 x 2100 x 3370 mm well-maintained condition (!!) - in checked condition - machine video - ?v=rPOBwTfVReo Equipment: - simple, conventional hydraulic press brake - swiveling control panel, left front - electro-motoric back stop (X axis) * adjustment via front control panel (button) Godpfxexab I To Al Uebu * with analog position display * fine adjustment via handwheel, front - with 3x stop fingers, manually adjustable - electro-motoric depth adjustment (Y1+Y2 axis) * with analog position display - 1x split set of 85° deer foot upper tool - 1x MultiV - universal die block, with several V-openings - 2x front, stable support arms - 1x freely movable double foot switch - 1x freely movable 2-hand control - side safety device (swivelling doors) - rear safety device (sliding door) - original operating instructions

Condition: new, saw blade diameter 350 x Ø 30/40 mm cutting diameter 135 mm cutting length 430 mm dimensions of saw-blade 350x3,0/2,4x40 mm turning speeds 3800 U/min Dust suction hood 100 mm total power requirement 3,0 kW weight of the machine ca. 100 kg dimensions of the machine ca. 1300 x 800 x 1600 mm - Crosscut and miter saws for crosscuts - Miter adjustment on both sides (60° / 45°), with fixed stop - Compound cut on one side up to 45°, with fixed stop - Stable cast iron construction - Precise ball bearing guidance of the tool slide hardened and welded steel shafts - manual saw feed - Saw blade infinitely adjustable in height - socket for opt. suction Cutting data : - Cutting length at 90° = 430 mm - Cutting height at 90° = 135 mm - Cutting length at 45° = 310 mm - Cutting height at 45° = 92 mm Special accessories included: - 1x HM circular saw blade 350 x 3.0/2.4 x 40 mm Z = 108 FTZ neg. for aluminum and plastic - Hydraulic feed brake, continuously adjustable Gbedpfx Ajxabqzjl Uju - Pneumatic material clamping from above consisting of: 2x vertical clamping cylinders, adjustable with hand levervalve - 1x machine stand - more powerful drive motor (3.0 kW)

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, turning length: 1,337 mm, turning diameter: 420 mm, General Control: Siemens 828 D Turning diameter: 420 mm Turning length: 1,337 mm Swing diameter: 700 mm Bar capacity: 89 mm Rapid traverse speed: 20 / 10 / 24 m/min Main spindle Bar capacity: 89 mm Chuck size: 305 mm Speed: 2,500 rpm Spindle power: 22 kW Spindle torque: 1,050 Nm Sub spindle Speed: 4,000 rpm Spindle power: 12 kW Spindle torque: 122 Nm Tool turret Technology: 12 stations Tool drive: 5,000 rpm Gbedjx Ag Hmepfx Al Usu Power: 9.4 kW Torque: 90 Nm Tool holder: BMT-65 / BH Travel X: 280 mm Travel Y: 120 mm Travel Z: 1,390 mm Equipment Chip disposal: chip conveyor Coolant capacity: 240 liters Tool measurement: measuring arm in the working area Part discharge: parts catcher Bar feeder: prepared