FAMUP MCP 45 E

FAMUP MCP 45 E

Condition: new, functionality: fully functional, machine/vehicle number: 8153336470, overall weight: 616 kg, volume flow: 399 m³/h, pressure (min.): 4 bar, pressure (max.): 13 bar, noise level: 67 dB, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, We are a company specializing in the compressed air industry for over 20 years. Professional level of service and high quality goods offered by our company - "proven" on the market - guarantee successful cooperation with you. We offer NEW screw compressor Atlas Copco GA37VSDs FF (variable speed with built-in dryer) Machine equipped with frequency converter (inverter), manufactured based on the latest technologies, which translates into greater efficiency and performance: On average 20% lower unit energy consumption (SER) than in previous models of the GA VSD series. Ecological and efficient VSD+ variable speed drive system reduces energy consumption by an average of 50% compared to models that operate at idle speed. Regardless of energy savings, efficiency (FAD) increases by up to 12%. Efficient fan motor (compliant with the ERP 2015 directive) reduces energy consumption and noise level. Superior Motor Efficiency (iPM) up to 94.5% exceeding IE3 efficiency levels. Built to work hard for your success. The industry-leading GA Series oil-injected rotary screw compressor delivers unmatched efficiency, high productivity and low cost of ownership – even in the harshest conditions. Technical data: capacity at 4 bar: 15.69- 13.75 l/s / 0.94-7.85 m3/min capacity at 7 bar: 15.67-129.35 l/s / 0.94-7.76 m3/min capacity at 10 bar: 15.68-110.79 l/s / 0.94-6.65 m3/min Max pressure 10 bar (13 Bar variant on request) Voltage 400 V Motor 37 kW Noise 67 dB(A) Crsdpfjwlp Hdjx Acpjh Weight 616 kg Motor with internal permanent magnets (IPM) Compression element Direct drive Innovative fan Separator/oil filter with durable construction Electronic water drain valve that does not cause compressed air losses Controller Elektronikon Inlet valve VSDs module Manufacturer code: 8153336470 If you are not sure whether the device is right for you, you have not found the right compressor, CALL! We will advise you on the right choice of device. We invite you to familiarize yourself with our full offer.

Year of construction: 1988, condition: ready for operation (used), Travel X/Y/Z: 1500mm/800mm/660mm, spindle speed: 10000rpm, table dimensions X/Y: 1740mm/750mm, tool capacity: 30, taper type: BT50, control: Mazatrol M-32, weight: approx. 11000kg. Credpfx Acstpp H Nopoh

Condition: used, Year of construction: 1999, operating hours: 65,090 h, functionality: fully functional, ET365 GS with bar feeder and chip conveyor The machine is fully equipped - Collection tray - High-pressure pump - Control cabinet air-conditioning unit - Kupa loader - The machine was purchased from a running production operation and has been technically inspected - Geometry measured and all settings adjusted - Wearing parts replaced - All functions checked and adjusted as required The machine is fully operational and ready for immediate production Crodpfxeycvaqe Acpeh The machine is available immediately

Condition: like new (used), Year of construction: 2018, Complete Aerzen D17L and D28L units are for sale. Manufactured in 2018, they are in excellent condition and equipped with 15 kW and 22 kW motors. Warranty included. For more information, please contact me by phone or email. Cedpfxolnlr Es Acpsrh

Condition: used, Year of construction: 1991, pressure 400 t stroke 300 mm table surface area 1200 x 700 mm ram surface 1200 x 700 mm dayligth 500 mm adjustment of stroke 300 mm return capacity 348 kN capacity of ejector 100 kN ejector stroke 100 mm control SIEMENS Simatic S 5 total power requirement 65 kW weight of the machine ca. 28 t dimensions of machine L x W x H 4,4 x 2,75 x 4,0 m = hydr. punching and embossing press Accessories: tool changing table - with cutting shock absorption damping force 4000 kN Cedpfx Acetqqlcopsrh damping stroke 5 mm spindle adjustment 200 m

Condition: used, Year of construction: 2004, functionality: fully functional, Friction welding machine RS125, max. upsetting force up to 190 tons, KUKA friction welding machine Modernized by the manufacturer KUKA, 2016. This machine is currently undergoing a complete overhaul in our workshop. The machine bed has been extended to allow welding of components up to 6 m in length, with automatic stop adjustment. Boring bar tubes with a diameter of 178 mm are included. Equipment: servo-hydraulics, facing unit, steady rest, 2/3 jaw chuck, "positioned welding" possible, e.g., for propeller shafts. Cjdpfjq Aurvex Acpjrh Currently, the friction welding machine is being used in our production for the manufacturing of hydraulic piston rods, aluminum-brass connections, the production of small and large screw taps, and the production of pressure rollers, etc. You are welcome to inspect this machine.

Condition: excellent (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: 1028, Thread Rolling Machine LEISTRITZ RT 400-CCA Year of manufacture: 2004 / Control system retrofit in 2019 Connection voltage: 3x400 V Frequency: 50 Hz Rated power: 65 kW Main fuse: 125 A Operating pressure: Air: 6 bar, Oil: 270 bar Control voltage: 24 VDC Maximum shaft length: 275 mm Minimum shaft length: 125 mm Maximum roll set diameter: Tool Ø69.85: 215 mm, Tool Ø80: 210 mm Cjdpfexytmhox Acpsrh Minimum roll set diameter: Tool Ø69.85: 176-178 mm, Tool Ø80: 176 mm Maximum rolling force: 40 t Space requirement: 3.4 m x 2.9 m x 2.2 m Weight: 4900 kg Accessories: - Coolant filtration system - Second spindle pair (1x for tools Ø69.85 mm, 1x for tools Ø80 mm)

Condition: used, Year of construction: 2021, turning diameter max. 2.800 mm diameter of spindle flange 1.100 mm max. swing diameter 3.000 mm control 840 D sl Siemens turning speed range - main spindle max. 230 min/-1 power capacity - main spindel 206 kW max. Torque 53.000 Nm tool taper Capto C8 swivellable B: 0 - 270 ° Spindle speed - driven tool pos. max. 6.000 min -1 max. Torque 120 Nm tool taper Capto C8 number of toolpositions 41 pos. max. tool weight 20 kg max. tool length 400 mm workpiece diameter at full load 150 mm tool taper Capto C8 number of toolpositions 25 pos. workpiece diameter at full load 150 mm max. tool weight 20 kg max. tool length 400 mm tool taper Capto C8 x-axis 1: 2.700 mm x-axis 2: 2.700 mm z-axis ( 2x 1.000 ) mm rapid traverse X: 40 / Z: 24 m/min feed power X/Z: 22 kN total power requirement 200 kVA weight of the machine ca. 120 t dimensions of the machine ca. 10,4 x 6,3 x 5,7 m CNC Vertical Turning Machine PITTLER - PV 2500 - Control Expansion / Software SINUMERIK 828D/840D SL ProgramSYNC Software Option - 12-Jaw Compensating Chuck RÖHM - Retractable Steps - Coolant Circulation - Coolant Conditioning - Oil Hose Skimmer - SIEMENS Safety Integrated - Network Interface / Data Transfer DNC Option - Variable Speed ??Range to Reduce Vibration - Air Purifier, Electrostatic Dispersal Codpfxsyrhlwo Acpsrh - Touch Probe for In-Process Workpiece Measurement - Walk-in Work Area

Condition: ready for operation (used), Year of construction: 2008, A Fanuc CNC drilling and machining center is available. Travel X/Y/Z: 700mm/400mm/330mm, distance from table to spindle nose: 180mm-580mm, table dimensions X/Y: 850mm/410mm, max. table load: 300kg, max. spindle speed: 10000rpm, spindle power: 26kW/5.5kW, torque: 35Nm/7.5Nm, feed rate: 30m/min, rapid traverse: 54m/min, tool stations: 21, tool interface: BBT30, positioning accuracy: 0.006mm, repeatability: 0.004mm, machine dimensions X/Y/Z: 2150mm/2050mm/2350mm, weight: approx. 2100kg, control: Fanuc 31i-B5, operating hours: approx. 9547h. Including chip conveyor and coolant tank. Documentation available. An on-site inspection is possible. Codpfx Acjzlt Snjperh

Condition: excellent (used), Year of construction: 2015, travel distance X-axis: 500 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 330 mm, controller manufacturer: FANUC, controller model: 31iB5, table width: 550 mm, table length: 380 mm, Equipment: documentation/manual, FANUC ALPHA T14iFb VERTICAL MACHINING CENTER, MANUFACTURED IN 2015 EQUIPPED WITH FANUC 31iB5 CONTROL ELECTRONIC HANDWHEEL TRAVEL: X 500, Y 400, Z 330 MM TABLE SURFACE: 550 x 380 MM DIRECT DRIVE SPINDLE, 24,000 RPM SPINDLE COOLANT SYSTEM Crjdpfx Acsy Tvnwepsh