Mechanical Shear

FEMAS CM 100

Condition: as good as new (ex-display), Year of construction: 2007, I - beam section - flat steel 50 x 10 mm I-beam section - upend 80 x 15 mm L-beam 50 mm Pedpfjt U R H Ujx Afuegt round material 30,0 mm bar material dia. max. 1 1/2" mm bar material - diameter 30,0 mm weight 185 kg range L-W-H 670 x 530 x 1350 mm square material 40 x 40 x 3 mm pipes 60 x 2,0 mm Thickness of tenon 30 mm total power requirement 0,75 kW Demonstration device Equipment: • Base frame of the machine • Foot switch • Standard-rolls (divided) • Possible to bend horizontally and vertically • machine has only one drive (right-left-run)

Condition: ready for operation (used), functionality: fully functional, Guillotine Shear – Mechanical Model: HSM-F 15/3.0 Machine No.: 11644-0995 Year of manufacture: 1995 Condition: Good, operational condition TECHNICAL DATA Cutting capacity: 1,550 x 3.0 mm Cutting angle: 2° Number of cuts per minute: 35 Motor power: 3 kW with brake, 380 V/50 Hz Manual backgauge: 0-500 mm Weight: 1,255 kg EQUIPMENT/ACCESSORIES Podpfxoydk Acj Afujgt  Angle stop with ruler  Double-edged blades  Foot switch  Documentation

Condition: used, Technical details: sheet width: 1500 mm plate thickness: 2,25 mm distance between columns: 1600 mm back gauge: nein cutting angle: nicht bekannt ° cutting gap adjustment: nein mm down holder: über Druckleiste Stück height over floor: 850 mm Table dimensions: LXB 1800 x 350 mm weight of the machine ca.: 0,85 t dimensions of machine: 2,0 x 0,8 x 1,3 m simple mechanical guillotine shear Pgedpfx Afeu Icn Esuet with shelf right/left 305 x 100mm operation via ON/OFF *

Year of construction: 2021, condition: ready for operation (used), A Boschert notching machine with an integrated punching station is available. Cutting angle range: 30°-120°, punching capacity: 15t, punching diameter range: 9.19mm-91.87mm, cutting length range: 53.85mm-53.46mm, max. sheet thickness: 10mm, punching force: 15t, stroke rate: 40/min, table dimensions X/Y: 1000mm/650mm, machine dimensions X/Y/Z: approx. 1250mm/1000mm/1200mm, weight: approx. 2000kg. Documentation vorhanden. An on-site inspection is possible. Pjdpfx Afsyugl Ieujgt

Condition: new, sheet width 1020 mm plate thickness 2.5 mm daylight opening 48.0 mm daylight opening 150 mm ohne Segmente bending angle max. 0 - 135 ° work height max. 900 mm weight of the machine ca. 340 kg dimensions of the machine ca. 1350 x 820 x 1300 mm Furnishing: - Swivel bending machines with segm. Upper, lower and bending beam - Universally usable bending machine for sheet metal works and repair shops - Robust construction in a modern design - Easy adjustment of the upper beam using a foot pedal - Hands are free for the workpiece - Manual bending machine for standard bending tasks - Segmented upper beam for a large number of bending possibilities - Optimum price-performance ratio - Quick and easy bending process using the bow handle - Non-slip rubber covering on the foot pedal for safe working - Easy adjustment of the lower beam to the respective sheet thickness - High upper beam for the production of high folded profiles Pjdsxaa E Dopfx Afujgt Scope of delivery : - Segmented upper, lower and bending beam - manual backgauge - Corner segment left / right each 75 mm | 25 | 30 | 35 | 40 | 45 | 50 | 75 | 100 |200 | 270 mm

Condition: used, Year of construction: 2008, sheet width 1530 mm plate thickness 4.0 mm thickness at "Niro-steel" 2.0 mm no. of strokes max. 34 Hub/min cutting angle 2.70 Grad distance between columns 1540 mm work height max. 920 mm Control konv. voltage 400 V engine output 3.2 kW weight of the machine ca. 1115 kg. range L-W-H 2275 x 2220 x 1400 mm Features: - Robust motorized swing-arm guillotine shear - Break-resistant, torsion-resistant welded steel construction - Compact and easy-to-use machine design - Manual backgauge, adjustable from the rear * Stepless adjustment across the entire travel range Pgsdpfxsxyln Rs Afuet - 1x hold-down bar - 1x freely movable foot switch - Front, extendable table extension - Rear safety device - Original operating instructions * Optional accessories included: - Sheet metal holding device for thin sheet metal blanks

Condition: used, Year of construction: 1970, Technical details: turning diameter over bed: 500 mm turning diameter over support: 300 mm turning length: 1000 mm center height measured in bed: 250 mm centre distance: 1000 mm revolution per minute: 18...1800 / 21 step U/min spindle bore of work spindle: 56 mm tailstock quill adjustment:: 180 mm longitudinal feeds:: 0,08 - 3,26 mm/U cross feed: 0,04 - 1,63 mm/U Rapid feed X axis: 4,2 m/min. total power requirement: 7,5 kW weight of the machine ca.: 2,9 t dimension machine xH: 2,6 x 1,1 x 1,3 m 4-jaw chuckØ 250mm with internal jaws live center in tailstock 4-fold quick-clamping tool holder coolant system Accessories: various reduction sleeves MK3-MK5-MK4 revolving tip "Clamping heart" 3-jaw chuck Ø 250mm with inner jaws The machine does not comply with APR (accident preventing regulations) * Podpfsvvrpkex Afuogt

Condition: used, Year of construction: 2003, XXL-Center RAS 75.06-2 long bending center for fully automatic positive and negative bending, where it is not necessary to turn the sheet metal. Usable length 6400 mm Maximum sheet metal thickness (400 N/mm²) 1.5 mm Four motorized and extremely fast axes controlled by CNC (no hydraulics) For: • Upper and lower bending beam speed: 126 degrees/s • Upper beam speed: 60 mm/s • Back gauge travel: 12-750 mm • Back gauge speed: 350 mm/s • Bending accuracy (depending on the quality of the sheet metal): up to +/- 1 degree Pgsdpfxezru Nzs Afuet

Condition: excellent (used), functionality: fully functional, machine/vehicle number: 2836-0192, Machine in good used condition, Dialog 11 control. Until recently, it was only rarely in operation in our own workshop. Documentation/manuals etc. are available. Additional accessories, cutters, zero point probes, etc. can be purchased optionally. Pgsdjylawxopfx Afuot

Condition: good (used), functionality: fully functional, Year of construction: 1994, Used SCHRÖDER motorized guillotine shear, type MHSU, built in 1994, No. 121204 Usable length: 1030 mm Max. sheet thickness: 2.5 mm - Pneumatic hold-down device - Front support arms 1000 mm - Digital back gauge 750 mm - Right-angle stop - Sheet support device - Forward sheet slide - Rear area protection with protective cage - Foot switch The machine is in stock at our location in 71334 Waiblingen-Beinstein and is available immediately. Pgsdpfx Afev Tzpheuot