Hydraulic miter band saw machine

KLAEGER HBS 220 DG

Condition: used, Precision lathe with cycle automation for chuck and shaft work, digital drive technology (Sinamics S120) and a Siemens Sinumerik 840D sl control running WEILER's operator-oriented SL2 software. Distance between centres 2000 mm, swing over bed 570 mm, spindle bore 83 mm, main drive 20/17 kW up to 2500 rpm. Year of manufacture 2022. Lsdpfxszl Ipno Ah Ssaf

Condition: used, Technical details: pressure: 100 t daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm ram speed - forward: 200 m/s ram speed - reverse: 200 m/s Table dimensions: 750 x 560 x 90 mm Lajdpfxsvc Ax Ne Ah Sjf passage inside table: Ø 26 mm clamping surface ram: BxT: 530 x 400 mm mortise hole in ram: Ø 50 mm cylinder diameter: Ø 250 mm height over floor: 720 mm total power requirement: 17,0 kW weight of the machine ca.: 5,5 t dimension machine xH: 1,8 x 1,2 x 3,2 m

Condition: new, cutting diameter 225 mm saw band length 2480 mm cutting width 250 mm cutting speed 45 / 90 m/min dimensions of saw-band 2480 x 27 x 0,9 mm capacity 45 degrees: flat 135 x 185 - 145 x 150 mm capacity 45 degrees: round 150 mm capacity 45 degrees: square 145 mm capacity 60 degrees: flat 63 x 107 - 69 x 90 mm Lajdpfx Ahelb I Dao Sjf capacity 60 degrees: round 70 mm capacity 60 degrees: square 70 mm capacity 90 degrees: flat 240 x 160 - 250 x 110 mm capacity 90 degrees: round 225 mm capacity 90 degrees: square 185 mm total power requirement 0,75 / 1,1 kW weight of the machine ca. 200 kg dimensions of the machine ca. 1385 x 580 x 890 mm Technical features: - Hydraulic head descent control system - End stop at the end of the cut - Powerful three-phase induction motor with 2 speeds and Transmission with oil bath - Saw frame, vice and swivel group made of cast steel - Steel blade guide with ball bearings - Vice with quick clamping - Lever integrated on the front for locking the miter adjustment - Coolant pump with aluminum body - Large hand wheel for easy saw blade tension - Pressure gauge to show the belt tension (600-1000 kg/cm3) - Emergency stop safety switch - Swarf brush for cleaning the saw blade STANDARD EQUIPMENT: - Mountable base cabinet - coolant tank - Electric coolant pump - Length stop for serial cuts - Band change and settings tools - Chip removal brush - Hydraulic cylinder with feed control

Year of construction: 1992, condition: good (used), machine/vehicle number: 29-0288, Offer 04612 Technical specifications: - Cutting range at 90° (round): 260 mm - Cutting range at 90° (flat): 450 x 240 mm Ljdpfxogin Nde Ah Soaf - Cutting range at 45° (round): 230 mm - Cutting range at 45° (flat): 240 x 200 mm - Machine is mounted on the original rotating table - Saw band dimensions: 3660 x 25 x 0.9 mm - Cutting speeds: 20 / 35 / 50 / 70 m/min - Hydraulic lifting and lowering of the saw frame - Cutting pressure, infinitely adjustable: 0 - 10 m/min - Total drive power: 400 V / 0.8 kW - Coolant system - Space requirement: approx. W 2100 x H 1200 x D 1000 mm - Weight: approx. 500 kg

Condition: excellent (used), machine/vehicle number: 68131, Cut-off saw Ø max .: 300 mm Ledpfx Ahjfug Exs Soaf here cutting area round: 100 mm Saw head can be swiveled up to: 45 ° Vice clamping range up to: 160 mm Cutting saw speed: 2500 rpm Drive motor: 230 V, 1.1 kW Required space: 850 x 750 x 1500 mm Weight: 126 kg

Condition: used, Year of construction: 1969, max. wheel diameter 160 mm gear width 355 mm max. module 4,5 min. module 0,5 centre distance 450 mm total power requirement 11 kW weight of the machine ca. 3,8 t dimensions of the machine ca. 2x17,1,6 m Wheel diameter - max. 160.175 mm Wheel width 355 mm Module - max. 4.5 Spindle bore 75 mm Center distance 410 mm Number of teeth - min. 2, 3 Cutter diameter max. 115 mm Cutter length max. 105 mm Center distance between milling cutter and workpiece - max. 138 mm Center distance between milling cutter and workpiece - min. 30 mm Milling head - swivels 120 ° Milling cutter speeds 70 - 400 rpm Axial feeds 0.25 - 4.0 mm/rev Radial feeds 0.09 - 1.5 mm/rev Total power requirement approx. 9.5 kW Machine weight approx. 3.5 t Space requirement approx. 1730x1400x1440 mm Equipment/accessories: - Changing wheels Laodpjvz Ec Isfx Ah Sof - milling arbors - Clamping device Dra8M7 - documentation

Condition: new, Year of construction: 2026, The CORMAK HBS275 band saw for cutting tubes, profiles and bars is widely used in all locksmith and metalworking workshops where precision, quality and cutting speed matter. The model is equipped with a 0-60° swivel arm; the saw guides are based on sintered carbide. The frame construction ensures accurate and quiet operation. Machine characteristics The horizontal metal band saw with swivel arm enables cutting in a plane perpendicular to the axis of the material being cut and at any angle within the range from 0 to 60°. The material to be cut can be fed manually or by any mechanical device, while the tool feed is automatic. The blade guides are equipped with special carbide plates and bearings. This has a major impact on blade guidance, service life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and blade. The machine is equipped with an efficient coolant pump with a closed coolant circuit. The saw arm is made of a single cast-iron casting and, together with the 27 mm wide cutting blade used in this saw, fully enables multi-series cutting of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The blade guides are equipped with hard metal plates – sintered carbide and a rolling bearing system. It is precisely the SINTERED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The arm has been inclined at an angle of 25°, which increases blade durability and improves cutting conditions. A cleaning brush is mounted at the bottom of the arm to achieve excellent cleanliness and blade operation. The machine drive is transmitted via a worm gearbox. The machine has a three-phase motor with two cutting speeds and motor thermal protection. The shape of the upper part of the base forms a tray for draining coolant and collecting chips generated during material cutting. A cast-iron work table with a swivel arm and a control panel on a separate arm is mounted to the base. In the cutting process, the main cutting movement is the movement of the cutting blade, while the feed is the lowering of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic cylinder. The feed speed is adjusted on the saw control panel. Two cutting blade speeds are available: 37.5 and 75m/min. In the lower position of the arm (after cutting the material), the cutting blade drive is switched off automatically. Safety is ensured by cutting blade guards and micro-switches that stop the motor after the cutting cycle is completed or when any guard is opened; additional protection consists of automatic shutdown of the saw in the event of cutting blade breakage. The machine drive is transmitted by a motor with a worm gearbox. The motor with thermal fuse protects against overheating during operation. Laodpfx Aoudi Uneh Sjf Technical data TOTAL POWER 1.5kW POWER SUPPLY 400V 50Hz ARM LOWERING ADJUSTMENT hydraulic cylinder BLADE LENGTH 2450 x 27 x 0.9 mm BLADE SPEED 37.5 / 75m/min VICE BASE HEIGHT 900 mm MACHINE DIMENSIONS (WITH ARM RAISED) (L x W x H) 1720 x 800 x 1800 mm WEIGHT 215 kg

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 4012M-4212, measuring range X-axis: 900 mm, measuring range Y-axis: 1,000 mm, measuring range Z-axis: 600 mm, workpiece weight (max.): 1,200 kg, Equipment: type plate available, Technical Data: Machine type: Mitutoyo STRATO 9106 FAL-A910 Year of manufacture: 2001 Measuring range: 900 x 1000 x 600 mm Software: Mitutoyo Software v2.4.R11 Lasdpfxoqz T H Ao Ah Ssf Accessories: Probe head mount: Renishaw SP80 Probe head: Renishaw SP80 Additional accessories: calibration ball (ceramic), various probe styli and extensions, Renishaw change rack, fastening kit with 4 x SCP80 and probe holder Modifications and errors in the technical data and information as well as prior sale are subject to change!

Condition: good (used), Year of construction: 1999, overall weight: 2,900 kg, total length: 1,800 mm, total width: 1,900 mm, total height: 2,200 mm, Length:1800mm Width:1900mm Height:2200mm Ledpfx Aheycu E Ej Soaf Weight:2900kg

Condition: used, Metal band saw Hans Schreiner MBS270, good condition, 1.5 kW, 2450 mm band length, 227 kg Lodpfxswzzgne Ah Ssaf Subject to price changes, errors, printing and typographical mistakes excepted.