Bending rolls buy used

Recognised location: Ashburn (US) (Change)
Enter e-mail address
or
Move
4
sheet width 1270 mm plate thickness 1,0 mm roll diam. toproll 56,0 mm bending speed 0 - 12 m/min. total power requirement 0,3 / 0,45 kW weight of the machine ca. 195 kg. 8pc7rbulu dimensions of the machine ca. 1.780 x 550 mm more
4
sheet width 2000 mm plate thickness 2 mm pre-bending 4 mm roll diameter 80 mm Drive 1,5 kW weight of the machine ca. 670 kg dimensions of the machine ca. 3 x 0,9 x 1,2 m Condition: ready for operation Onttjqh7 Electric 380 Volt Foot switch Asymetric roller arrangement, rear roll adjustment and lower roll adjustment over handwheel, elektr. safety control, upper roller forward swing-out. The sheet thickness refers to a strength of 400 N. Machine dealer with own stock of 2500 m² and cert... more
5
sheet width 3050 mm plate thickness 10 mm pre-bending 8 mm upper roll diameter 270 mm side roll diameter 250 mm total power requirement kW weight of the machine ca. 11,5 t dimensions 6,25 x 1,92 x 1,63 m - with conical bending 7ezucjtkx - with hydr. supports bearing Acc.: DRO for side rolls and lower roll, interchangable upper roll 200 mmø more
5
plate thickness:8 mm pre-bending:6 mm length:2000 mm Mstmp hydr. moveable counter bearing for upper roll, hydr. opening for upper roll, 2 shift gearbox for rpm, more
5
Three rolls round, three roll - bending machine, bending machine, four rolls round, four roll - BlechbiegemaschineBlechrundbiegemaschine, 3-roller bending machine, 4-roller bending machine Machine is sold as spare parts carrier -no control -without Hydraulikaggreagt -beidseitige Prebending Diameter of the roller below 160 mm Roll diameter above 235 mm -einseitige hydraulic sheet metal retaining -maximum sheet width 2050 mm -maximum sheet thickness: 4 mm drive roller kW 2utcpl30z Spe... more
6
sheet width: 1550 mm plate thickness: 12 mm pre-bending: - roll dia. top roll: 230 mm roll dia. bottom roll: 200 mm voltage: 380/50 V total power requirement: 26 kVA weight of the machine ca.: 4,4 t transport measurements machine: 4,0x0,8x1,2 m 7nkp2lw0k dimensions electric cabinet: 1,0x0,65x1,5 m Plate Bending Machine - 3 Rolls more
4
sheet width 1020 mm plate thickness 1,0 mm ST roll diam. toproll 50,0 mm Mt7mr bending speed manuell m/min weight 180 kg range L-W-H 1,4 x 0,5 x 1,0 m more
4
sheet width 2040 mm plate thickness 2 mm pre-bending ja roll diameter 110 mm Drive 1,5 kW weight of the machine ca. 980 kg dimensions of the machine ca. 3,1 x 0,9 x 1,05 m Condition: ready for operation electric for three-phase 380 Volt Foot pedal 2897rchtu Machine dealer with own stock of 2500 m² and certification of the database "Machineseeker". more
4
sheet width 2500 mm L23dv plate thickness 10 mm pre-bending 8 mm upper roll diameter ca. 240 mm lower roll diameter ca. 240 mm total power requirement kW weight of the machine ca. 7 t dimensions 4,85 x 1,4 x 1,7 m - with conical bending device - with extensions of bending rolls for fixing profile bending rolls - with DRO for adjustment of lower rolls more
3
sheet width unbek. mm U2gumuwu2 plate thickness unbek. mm pre-bending total power requirement kW weight of the machine ca. t dimensions of the machine ca. m more


bending ro...
every day

New machines via email!

Be informed!
4
 Chat starten

3 rolls bending machine

Heilbronn Germany
6634 km
USED
Elu8xb0troll lenght 1000mm upper roll diameter 96mm lower roll diameter 100mm more
1
sheet width: 1000 mm plate thickness: mm pre-bending: - roll dia. top roll: mm roll dia. bottom roll: mm voltage: V Fb7ssa9 total power requirement: kVA weight of the machine ca.: t transport measurements machine: m transport measurements [...]: m dimensions electric cabinet: mm The machine is currently in research of technical details. more
6
sheet width 2050 mm plate thickness 25,0 mm pre-bending capacity 20,0 mm upper roll diameter 300,0 mm side roll diameter 230,0 mm lower roll diameter 280,0 mm Number of working hours 28 h Control NEXUS 9gh9rke8h total power requirement 11,0 kW weight of the machine ca. 8.400 kg. more
5
sheet width 3040 mm plate thickness 7 mm pre-bending ja roll diameter 225 mm main drive 11 kW back roll setting 4 kW weight of the machine ca. 5,3 t dimensions of the machine ca. 4,4 x 1,15 x 1,47 m Condition: ready for operation Electric 380 Volt Foot pedal Light barrier control L3jmb with asymmetrical roller arrgement and pre-bending. Machine dealer with own stock of 2500 m² and certification of the database "Machineseeker". more
6
1 used 4-Rolls hydraulic Plate Bending machine Manufacturer MG / Italy Model MH 3050 H YOM 2008 with cone bending Sheet width = 3100 mm Max. bending thickness = 50 mm Max. prebending thickness = 40 mm Xfjwxm9i2 Dia. top roll = 530 mm Dia. bottom roll = 500 mm Dia. site rolls = 440 mm Power of main motor = 45 kW Weight of the machine approx. 46 ton Dimensions : Length x width x height = 6300 x 3000 x 3000 mm more
3
C28yhftcSERTOM-CASANOVAS Plate Bending Machine 4 rolls. Max sheet width 3050 mm. Pre-bending 32 mm. Plate thickness 50 mm. Rolls diameter: • Central rolls 500 mm. • Side rolls 400 mm. Power 37 Kw - 400 V - 50 Hz. Machine dimensions: 4550 x 2100 x 1800 mm. Weigth 52.000 Kgs. Equipped with: • CN for bending. • Hydraulic l-rafter SIAM. • Ferrule side support more
1
sheet width: 1500 mm plate thickness: 3 mm pre-bending: - roll dia. top roll: mm roll dia. bottom roll: mm voltage: V total power requirement: kVA weight of the machine ca.: t transport measurements machine: m Bht3mpgo transport measurements [...]: m dimensions electric cabinet: mm The machine is currently in research of technical details. more
4
sheet width 2020 mm plate thickness 1,0 mm roll diam. toproll 80,0 mm total power requirement manuell weight of the machine ca. 500 kg. range L-W-H 3000 x 900 x 1200 mm 7brg72sqm more
6
sheet width 1860 mm plate thickness 0,75 mm pre-bending ja upper roll diameter 68 mm work speed 2 m/min length of draw-in 500 mm diameter of lower rolls ca. 90 mm weight of the machine ca. 700 kg dimensions of the machine ca. 2,45 x 0,7 x 1,1 m Electric 380 Volt Reflector plate bending machine with automatic curve control (templates) with asymetric roller arrangement, hydraulic rear roll adjustment and three roll drive. During automatic operation sequence a sensor valve on template is st... more
4
sheet width 2050 mm plate thickness 3,0 mm pre-bending 2,0 mm roll diameter 130,0 mm work height max. 800 mm 9vmiyalxh bending speed 4,0 m/min total power requirement 5,0 PS weight of the machine ca. 2.500 kg. ca. range L-W-H 2.800 x 725 x 1.150 mm more
4
sheet width 3050 mm 3qaa7ecf plate thickness 25,0 mm material strength at pre-bending 20,0 mm roll diam. toproll 410 mm roll diam. bottom roll 310 mm min. dia. 470 mm mm bending speed 0 - 5,0 m/min. weight of the machine ca. 28.000 kg range L-W-H 6,0 x 2,6 x 3,7 m more
6
sheet width 1550 mm plate thickness 6,5 mm pre-bending 4,5 mm diameter of upper rolls 150 mm side roll diameter 130 mm diameter of lower rolls 150 mm total power requirement 2,2 + 1,5 kW weight of the machine ca. 2.370 kg. range L-W-H 3.300 x 1.150 x 1.110 mm Mrutf more
4
sheet width 1030 mm plate thickness 3,0 mm Qmmxvgz00 upper roll diameter 160 mm lower roll diameter 160 mm side roll diameter 100 mm total power requirement 4,0 kW weight of the machine ca. 2.300 kg. more
6
sheet width 2050 mm Cccjaufw plate thickness 10,0 mm pre-bending capacity 8,0 mm upper roll diameter 200 mm side roll diameter 170 mm lower roll diameter 190 mm total power requirement 4,0 kW weight of the machine ca. 2.490 kg. more
3
Isitan CMS 610 x 1mm CMS 610 x 1mm Brand New 3 in 1 Fold, Shear and Roll Many other sizes and capacities available Dpb3sit03 Feel free to enquire for more information Can be viewed at anytime more
2
sheet width 1300 mm plate thickness 4,5 mm pre-bending - diameter of upper rolls 90 mm diameter of lower rolls 120 mm 2,2 kW weight 660 kg dimensions of the machine ca. 2,0 x 1,2 x 1,4 m Lkks7 • unused 3-Bowl-Bending machine, • enables conical bending by adjustment of the lower rolls, • operation by foot pedal, • hardened rolls, more
5
Neupreis 2005 € 101.000.- mit Konischbiegefunktion mit hydr. Klapplager zum entnehmen gewalter Bleche mit fahrbarem Bedienpult Biegelaenge: 3050 mm max. Biegeleistung: 35 mm Anbiegeleistung bei 660 mm Durchmesser: 25 mm Anbiegeleistung bei 2200 mm Durchmesser 30 mm Biegeleistung bei 2200 mm Durchmesser 35 mm Baigujrqun Biegegeschwindigkeit: 0 - 2,5 Meter/minute Zentralwalzen: 440 mm Seitenwalzen: 340 mm Motor: 37 kW-1450rpm + 1,5kw-1450rpm LxBxH 6550x2260x2400 mm Gewicht: 33 ton more
3
sheet width 1050 mm plate thickness 3,3 mm pre-bending 3,0 mm roll length 1050 mm roll diameter 90,0 mm min. dia. 130,0 mm engine output 1,1 kW weight 570 kg range L-W-H 1750 x 1200 x 850 mm •Cast iron body •By manuel or motorised (optional) bending •Opening top roll to side after bending for taking out the material easily •Cone bending device •Movement of the back and bottom rolls up and down manually with hand wheel 7nv2eva3n •Portable control panel in order to control material from requir... more
5
sheet width:1000 mm plate thickness:1,25 mm dimensions of the machine ca.:1,20 x 0,60 x 1,20 m weight of the machine ca.:190 kg Ieigcjb more
6
sheet width 2030 mm plate thickness 2,5 mm distance between columns 2100 mm diameter of upper rolls 110 mm total power requirement 3,6 KW weight of the machine ca. 1,2 t Eqoywmrfo dimensions of the machine ca. 2,7 x 1,3 x 1,5 m . more
2
? Two rolls powered by a single gearbox and gear system for top and bottom rolls ? SAE 1050 Quality certificated steel rolls with high tensile strength ? Spheroid Cast Iron Main Frames ? Mobile control panel by foot pedal ? Conical Bending Device ? Manual dropend ? Top roll support system 2qtl0y ? Wire grooves at the end of the rolls ? Precision Bending with Brake Motor ? Built according to EC Safety Directives (CE) ? Model IRM 2550×140 produced standard with motorised back roll ? User?s Manual... more
3
sheet width:1050 mm plate thickness:1,5 mm diameter of upper and back rolls:57 mm Ucz7woyjh lower roll diameter:60 mm weight of the machine ca.:120 kg dimensions of the machine ca.:1600 x 600 x 1100 mm 1 used DURMA 102/15 3-rolls bending machine with following equipment: - asymetric roller arrangement - upper roll with fold notch - wire core grooves - upper roll swing-out more
4
Arbeitsbreite: 3000 mm Oberwalzendruchmesser: 520 mm Baigphnq93 Unterwalzendurchmesser: 368 mm Kleinster zu erzielender Rohrschuss Durchmesser: 650 mm Groesste Blechstaerke Normalbiegen: 35 mm mit hydraulischem Klapplager mit Hochhaltekran Bedienung ueber seperatem Bedienpult Gewicht: ca. 60 ton more
6
Roll Bending Machine 3 Rolls Herkules Wetzlar Roll Bending Machine 3 Rolls Herkules Wetzlar Brand : Herkules Wetzlar 93lpywheh Made : Germany Length : 2m Thickness : 16mm more
2
sheet width 2500 mm plate thickness 3 mm pre-bending Dbtw3b29o total power requirement kW weight of the machine ca. 4 t dimensions of the machine ca. 5x2x1,5 m more
6
sheet width 4000 mm plate thickness 40 mm pre-bending 29 no. of rolls 3 roll length 4050 diameter of upper rolls 450 / 370 mm pressure 270 t total power requirement 35 kW weight of the machine ca. 31 t dimensions of the machine ca. 7,0 x 2,0 x 2,1 m Technical specifications · Number of rollers: 3 Of which vertically adjustable: 1 upper roller (driven and interchangeable)) Horizontal Adjustable: 2 side rollers (individually driven) · Roll length: 4050 mm · Free stand through: approx. 4150 m... more
5
sheet width:3000 mm plate thickness:20 mm Clpjr27 pre-bending:16 mm upper roll diameter:340 mm side roll diameter:310 mm total power requirement:ca. 11,2 kW weight of the machine ca.:16 t dimensions of the machine ca.:6,4 x 1,7 x 1,8 m more
4
sheet width:1500 mm plate thickness:3 mm pre-bending: roll diameter:90 mm dimensions of the machine ca.:2380 x 730 x 1200 mm weight of the machine ca.:400 kg Mtxiok more
4
sheet width 2020 mm plate thickness 4,0 mm max. plate thickness 3,0 mm anbiegen roll length 2020 mm min. dia. 150 mm roll diam. toproll 170 mm engine output kW min. dia. 195 mm weight 1450 kg B3ymucmm more
5
sheet width:3050 mm plate thickness:50 mm C28yiwns pre-bending:32 total power requirement:37 kW weight of the machine ca.:52 t dimensions of the machine ca.:4,6 x 2,1 x 1,8 m SERTOM-CASANOVAS Plate bending machine Plate Bending Machine 4 rolls. Max sheet width 3050 mm. Pre-bending 32 mm. Plate thickness 50 mm. Rolls diameter: ?Central rolls 500 mm. ?Side rolls 400 mm. Power 37 Kw - 400 V - 50 Hz Machine dimensions: 4550 x 2100 x 1800 mm Weigth 52.000 Kgs. Equipped with: ?CN for bending. ?Hyd... more
6
sheet width 2500 mm plate thickness 15 mm pre-bending Ja/yes roll diam. toproll 250 mm roll diam. bottom roll 220 mm total power requirement kW weight of the machine ca. 8 t dimensions of the machine ca. 5x2,2x2 m Dixl7ynn more
3
sheet width 2000 mm plate thickness 8 mm pre-bending 6 total power requirement 6 kW weight of the machine ca. 8 t dimensions of the machine ca. 4 x 2 x 2 m Rfgbjcoqw mechanic machine. more
5
sheet width:4000 mm plate thickness:65 mm pre-bending:55 roll length:4070 mm power capacity:125 PS Drive capacity - Hydraulic -:10 PS weight of the machine ca.:110 t Teguwkg dimensions of the machine ca.:9,5 x 2,9 x 3,9 m more
6

Pyramid Bending Rolls PICOT RCS235-30

Düsseldorf Germany
6383 km
2008
USED
Offer
Another 9 days
Dimensions (l x w x h) approx.: 4900 x 1200 x 1400 mm Weight approx.: 7000 kg Description: 3000 x 8/6 Capacity, 8 mm Thickness, 6mm Chewable, Upper Roll 235 mm Dia, 8kw, 400v, Triple Rolls, Ser No 2008124 Baez2mmbhn In Online Auction with approx. 18 further Machine Tools and other Assets! Bidding ends: Thursday, 30 November 2017 from 2pm (local time) Auction start price: EUR 9.500 (plus VAT and 15% buyers premium) Your contact person: Hans-Uwe Ropertz more
3
working width: 2550 mm metal sheet thickness: 5 mm upper roller-Ø: 180 mm below roller-Ø: 160 mm electrical connection: 380 V kW 97plyhomt weight: 3500 kg space needed: 4100 x 1250 x 1150 mm more
2
sheet width 2000 mm plate thickness 22 mm pre-bending 18 total power requirement 47 kW weight of the machine ca. 18 t Bending length2,000mm Rcm00eq7m Bending thickness22mm Bending thickness when bending ends of sheet18 mm Roll Ø of upper roll330mm Roll Ø of lower roll310kg Total electrical load, approx.47 kW - 380 V - 50Hz Weight, approx.18,000kg Accessories / Special Features "2 pieces motor-driven lower rolls, which can be tilted for bending the ends of metal sheet. "Display for rollin... more
6
sheet width 3000 mm plate thickness 30 mm pre-bending 20 mm digital readout work speed m/min diameter of upper rolls 405 mm Mtp3d0 diameter of lower rolls 400 mm side roll diameter 320 mm total power requirement 45 kW weight of the machine ca. t dimensions of the machine ca. m more
5
DAVI PROMAU MCB 3070 WT 4 rolls CNC Hydraulic bending machine 3000 x 86/72 4 Rolls Type MCB 3070 WT Year 2008 Capacity mm. 3000 x 86/72 Vp7sr8dj Side and vertical arms CNC : MCB Leonardo Wind Tower Control Maximum thickness invitation of 3000mm width 72mm Fe 410 (As reported in Nameplate) Maximum thickness in the calendering of 3000mm width 86mm Fe 410 (How reported Nameplate) dimensions: top roll diameter: 700mm lower roll diameter: 640mm Lateral rolls diameter: 540mm Roller Table len... more
6
SCHAEFER hydraulic bending pinch With sheet support Reduced price:12750 EURO ex-site Not including loading costs Machine must be moved by 31/10/17 more
6
machine description Technical specifications · Number of rollers: 3 of which vertically adjustable: 1 upper roller (driven and interchangeable)) horizontal Adjustable: 2 side rollers (individually driven) · Roll length: 4050 mm Dvygeq · Free stand through: approx. 4150 mm · Diameter of upper roll 1: 450 mm · Diameter of upper roll 2: 370 mm · Diameter of side rollers: 400 mm · Drive power: 30 KW · Rotation speed of the rollers: 1000 to 5000 mm / min, in three stages Step 1: 1000 mm / min Step 2... more


bending ro...
every day

New machines via email!

Be informed!

to

to

Change search
BENDING ROLLS
SELL IMMEDIATELY
on Europe's market leader for as little as € 0,79 per ad.
Find out more now


Phone: +44 (0) 20 806 810 84
or sell immediately
Try our Machineseeker app now!
Machineseeker app for iPhone and Android.
Want to really stop the chat history?
Yes No
×
Machine Finder chat
Name E-mail Your message to the Dealer
START CHAT WITH DEALER
  You are chatting with: 
  Your contact person: 
  
Your contact is typing
SEND MESSAGE
  You are chatting with: 
  Your contact person: 
  
Your contact seems to be inactive
Chat window close