Used Bevelling for sale (506)

Condition: new, machine/vehicle number: 2b58968e34fac93b429a256e9, empty load weight: 5 kg, maximum load weight: 12 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Quarter-shell mudguards in front of 1st axle Spare wheel holder for 1 electric wheel, with wheel mounting kit Spare wheel, same make as basic tires, steel rim Plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Low loader lashing eyes 3 pairs of lashing points, each 10 tons, integrated in the floor at the front 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x according to the rest of the neck area, distributed between them, spacing not greater than 1200 mm 1 x rear bevel 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cableVoltage converter for 12/24 volt operationNote! A 7-pin 12 volt socket is required on the tractor/tractor! (Required in conjunction with electrical voltage converter!) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white/red rear lane departure lights 2 white position lights at the front Additional LED work light(s) at the rear, switched via reversing light 2 x 7-pin interchangeable plugs at the front, with connecting cable1 x 7-pin agricultural plugVoltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Hedpfxsi Ri Nxs Aaqew covered with wood with spring lift support Operating instructions A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 t GG. Customer risk. Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: used, Year of construction: 1997, functionality: fully functional, overall weight: 310 kg, sheet thickness steel (max.): 50 mm, Material thickness: 8-50 mm. Bevelling angle: 30° Bevelling width: 17-25 mm. Motor: 3 HP. Year: 1997 Country of origin: Italy. Size (L x W x H): 550 x 800 x 1100 mm. Weight: 310 kg. Minimum material width: 100 mm. With new cutting wheel. All our machines are tested and serviced before delivery. Hsdpfx Aaexpfp Tsqew

Condition: used, Year of construction: 2011, Vertical Semi-Automatic Chainsaw EISMO-IMET type WS 370 SA Year of construction: 2011 Blades dimension: Ø 370 mm Cutting capacity: Straight cut Ø 120 /180 x 100/100 x 100 mm Hedpfx Aaexp Nxfsqew Bevel cut: 45° right - 45° left - 60° right Pneumatic vise Adjustable forward/downward Lubricant pump Voltage: 380 V Width: 800 mm Depth: 1200 mm Total height: 2000 mm Weight: approx 500 kg

Condition: used, Year of construction: 2017, FICEP GEMINI G32 HPE. Year 2017. MAXIMUM LENGTH 6100mm MINIMUM LENGTH 1250mm MAXIMUM WIDTH 3100mm MINIMUM WIDTH 800mm. DRILLING CAPACITY MAXIMUM HOLE DIAMETER DRILLED / MILLED 40mm (250mm) MINIMUM PLATE THICKNESS 5mm MAXIMUM PLATE THICKNESS THAT CAN BE DRILLED 80mm MAXIMUM PLATE THICKNESS WITH HPR 260XD 38mm PRODUCTION PIECE 64mm EDGE CUTTING 27mm WITH BEVEL CUT 45 DEGREES PRODUCTION PIECE 45mm WITH BEVEL CUT 45 DEGREES EDGE CUTTING. Hsdpfxsxmvn Us Aaqjw

Condition: good (used), Year of construction: 1979, functionality: fully functional, GLEASON 1979 COMPLIANCE CHECK OK 2024 TOOLING PROVIDED POSSIBILITY TO LOAD MACHINE ONTO TRUCK LOADING NOVEMBER 2025 Hjdpfxjxn Ul Io Aaqjw

Condition: used, Year of construction: 1997, Beam planer 260 x 160 mm, rotating bevel unit on the upper spindle with two-axis control for the left and upper spindle max. working width: 260 mm max. working height: 160 mm Number of spindles: 6 pieces 1. Spindle: bottom spindle diameter 40 mm clamping length 270 mm speed 6000 rpm motor power 11.0 KW 2. Spindle: right spindle diameter 40 mm clamping length 170 mm speed 6000 rpm motor power 11.0 KW shared motor with left spindle 3. Spindle: left spindle diameter 40 mm clamping length 170 mm speed 6000 rpm 4. Spindle: top spindle diameter 40 mm clamping length 270 mm speed 6000 rpm motor power 11.0 KW Spindle: bottom Spindle diameter 40 mm Motor power 11.0 kW Speed 6000 rpm Clamping length 270 mm 6th spindle: top Chamfering unit Motor brakes: mechanical Up/down adjustment of the upper spindle: electric, selectable with/without feed Feed brake system: Yes Continuous feed speed up to: 3 - 23 m/min Feed roller pressure: pneumatic Feed power: 4.0 kW Feed drive: cardan Lubricant pump: manual Max. chip removal for joining: 10 mm Jointing bevel cutter on planer: Yes Driven rollers in the table: 1 Control type: PLC control Dimension display on spindle: mechanical numerical display Infeed rollers in front of planer: Yes Air cushion table: three-track Central lubrication point: Yes Description: short infeed table 1050 mm with interior light Hjdpfx Aaswwwkhoqow Storage location: Nattheim

Condition: new, machine/vehicle number: cd0062ee491e6794168ccb01a, empty load weight: 8 kg, maximum load weight: 26 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 435/50 r 19,5, Further information Chassis semi-trailer In proven HANGLER welded construction made of high-quality steel with UP-welded side members tapered towards the front. Frame neck height 120 mm, with double center bar. Z-profile cross members punched through on the side member with floor panels (larger spacing) and with welded special side frame.2 kingpins to DIN 74080, replaceable, with grinding plate beveled to the front, made of high-quality sheet steel. EC front turning radius 2,040 mm. Sliding plate continuously welded from saddle plate to front plate *inside* 18 pairs of lashing eyes embedded in the outer frame, 2.5 tons each 8 pairs of lashing eyes embedded in the outer frame, 5 tons each 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminum side collision protection Plastic mudguards with splash protection mats Underride guard Impact protection at the rear Spare wheel holder for 1 e-wheel, with wheel mounting kit 3 Plastic tool box, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Aluminum ladder 3 300 mm, loose Pair of recessed stanchion pockets Piece of stanchions Storage compartment for plug-in slats on one side in FR left, below loading area Storage compartment for drop sides underneath the cargo bed, open, if technically possible Coil trough/inclined loading device Coil trough 8,000 mm long with cover and rubber pad. Cover 35 mm. With inclined loading bars and supports suitable for FR 80/80/4, complete stanchions 80/80 incl. lower reinforcement supplied Hydraulic sloping loading device with 4 crossbars:Hydraulic supply via tractor unit by means of 2-pipe pump system (forward/return) with 2-fold Faster coupling mounted on bulkhead (hoses are connected to Faster coupling from below).Sloping loading bars (FR 180x100x8 mm) with integrated extension part can be locked in height. Multi-stage hydraulic cylinders, each beam with cardanic suspension Incl. outriggers - adjustable - with bolt safety device underneath the loading area5-fold control block for operating the sloping loading device and for folding device sliding roof.1 set of boiler floor holder with height-adjustable support bolts for different boiler floor diameters, incl. shelf.1 piece of stop protection for sloping plate - for securing to the front! Axles + suspension SAF disc brake axles Offset axle spacing mm Air suspension Brake system 2-line compressed air brake system Aluminum air reservoir Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS make Wabco, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift & lower valve + auto-reset function Vehicle - driving stability system Wheels and tires 435/50 R 19.5, manufacturer's choice Factory silver steel rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 additional LED work light(s) at the rear, switched via reversing light 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, detachable with plug Hsdei Riw Hopfx Aaqjw 1 rotating beacon with holder, detachable Floor Screen printing plates approx. 3

Condition: used, The Klingelnberg GKP 90 bevel gear testing machine was designed as a universal machine and is used by manufacturers of gears and transmission technologies for noise and contact pattern testing on bevel and hypoid gears. Technical Data • Diameter: 540 (400) mm • Hypoid: ±50 mm • Pinion spindle diameter: 90 mm • Dimensions (LxWxH): 1,800 x 1,800 x 1,600 mm • Machine weight: approx. 2,800 kg *Information and data are provided without obligation. Subject to prior sale. Special Features: The machine is intended for noise and contact pattern testing on bevel and hypoid gears of all gear types. By simulating operational conditions, applying various rotational speeds, and switching load states between drive and coast, the optimal installation distance for standstill can be determined. • Digital actual value display for 2 axes Hsdpfxoxpq Nls Aaqow • Infinitely variable speed adjustment via frequency inverter • Electrically secured and removable safety guard • Accessories: Large number of workpiece holders • Condition: Very good

Condition: excellent (used), rotational speed (max.): 55 rpm, type of input current: three-phase, Geared motor, drive motor wiht brake several pieces for sale from stock. Manufacturer electric motor ziehl abegg RFZU180 Manufacturer Gear Sew-eurodrive S92 LP180 Output 1.42 / 8.5 kw Speed 8/55 brake - Bevel gear Hjdpfodyd Nxsx Aaqsw Protection IP 23 -Weight 350kg Purchase, Acquisition, asset management of industrial equipment and machinery. Wide Range of Used Machinery, Industrial Equipment

Condition: refurbished (used), Year of construction: 1991, 1 piece overhauled industrial helical bevel gearbox from Flender TGL 21814 with backstop Maximum torque: 28,000 Nm Gear ratio: i= 1:20 Max. power: 105 kW Oil filling: 135 kg Speed: n1= 710 Speed: n2= 35 Maximum speed to transmission power (only with oil cooler) 710 rpm to 112 kW 950 rpm to 149 kW 1400 rpm to 220 kW Hodpfxod Nqkro Aaqew Maximum speed to transmission power (without oil cooler) 710 rpm to 105 kW 950 rpm to 115 kW 1400 rpm to 130 kW Weight: 1560 kg Shaft diameter d1: 90 mm Shaft diameter d2: 160 mm Shaft height h1: 500 mm Total height h2: 925 mm Length of base: 1170 mm !! Gearbox has no oil cooler !!!

Condition: new, empty load weight: 2,980 kg, maximum load weight: 7,520 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 6,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245 / 70 R 17,5, wheelbase: 990 mm, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, each ramp approx. 2,700 mm long x 560 mm wide, ramps with gratings, loading height: 840 mm, 12 lashing eyes each 2.5 t, 8 x lashing eyes each 6 t, steel drop sides, foldable and removable, wooden planks 50 mm, loading area rear beveled, loading area width inside 2.480 mm, rear stanchion removable, front for through-loading, , Also available in 5,300 mm loading area length! , , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Hsdpfjxghumsx Aaqsw

Condition: used, Year of construction: 2014, CNC portal plasma cutting machine Manufacturer: Microstep Model: MG PrA 16501.25 S1200 (2 bridges) Year of manufacture: 2014 CNC control Hjdpewqg T Ssfx Aaqew Working area: 16,500 mm x 2,500 mm + 1,200 mm trench 2 gantries Gantry 1: Plasma rotator with Kjellberg HiFocus 280i neo power source Gantry 2: Oxy-fuel torch, gas type: acetylene The integrated 1,200 mm trench is additionally equipped with a pipe cutting device for pipe diameters 30 mm – 700 mm and a maximum length of 16,500 mm Donaldson DFPRO 16 Cyclopeel filter system for outdoor installation Software for - Nesting, - Bevel cutting, - Pipe processing

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Hsdpsi Ri Rvjfx Aaqow Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: used, Year of construction: 2009, Suitable for automatic grinding of carbide circular saw blades on the face and back in a single setup. All common tooth geometries (flat, alternate, trapezoidal, etc.) can be grinded automatically and in a single pass. Accessories: Total enclosure, ND 230 loader (3-pallet loader), 4 loading carriages including 30 mm mandrels, measuring probe, grinding device with oil cooling, additional coolant cleaning system, automatic fire extinguishing system, automatic central lubrication system, extraction for oil and emulsion mist, alphanumeric keyboard, machine light, DES 300 data entry station for recording technical data of the circular saw blades including keyboard, monitor, and mouse, oil drip tray with floor grid, 2 grinding wheel holders, 1 saw blade magnet holder. Circular saw blade diameter without robot: 80-840 mm Circular saw blade diameter with robot: 100 - 630 mm Circular saw bore diameter: with robot from 10 -180 mm Sheet thickness without robot: up to 14 mm Hedpfsxfg Dwsx Aaqew Sheet thickness with robot: up to 5 mm Tooth pitch: 6 - 120 mm rake angle: -35° to +40° Bevel grinding on the tooth back: up to 45 ° clearance angle: 5° - 45° Bevel grinding on the negative tooth face: up to 30° Working speed for breast and back grinding: up to 12 teeth/min., Machine dimensions L x W x H =: 2316 x 1860 x 2058 mm weight machine: 3000 kg Loader weight: 1400 kg Grinding path and grinding speed per machining surface on the tooth: infinitely adjustable Dimensions loader L x W x H =: 3840 x 2020 x 2000 mm Connected load approx.: 4.4 kW (400 V / 50 Hz) colour: telegrey RAL 7045/7047

Condition: used, Worm gear, bevel gear Manufacturer: Sew-Eurodrive Type: DFY112ML/TH Output speed: 1400 rpm Torque: 24 Nm Power: 6.6 kW IP65 Voltage: 50 Hz V 230/400v Hedpfjudywgox Aaqsw Power consumption: A 49.50/16.50 Speed: 3000 rpm Gear ratio (i): 27.88:1 weight: 36 kg

Condition: good (used), Geared motor, electric motor, electric geared motor, bevel geared motor -Manufacturer: MAZ, gear motor with brake -Gearbox: Type 80D S1 i= 84 / 1 -Speed: 11 rpm -Engine: Type B REL 80S/6 K4 0.18 kW -Shaft: Ø 20 x 40 mm Hsdsxd Ui Eopfx Aaqow -Protection class: P54 -Brake: 4 Nm -Dimensions: 450/270/H200 mm -Weight: 20.7 kg

Condition: new, empty load weight: 2,980 kg, maximum load weight: 7,520 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 6,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245 / 70 R 17,5, wheelbase: 990 mm, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, each ramp approx. 2,700 mm long x 560 mm wide, ramps with gratings, loading height: 840 mm, 12 lashing eyes each 2.5 t, 8 x lashing eyes each 6 t, steel drop sides, foldable and removable, wooden planks 50 mm, loading area rear beveled, loading area width inside 2.480 mm, rear stanchion removable, front for through-loading, , Also available in 5,300 mm loading area length!!!, , Rental price from 500 ¤ , , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Hodpfx Aoxghugjaqew

Condition: used, Year of construction: 1980, overall weight: 7,000 kg, workpiece diameter (max.): 280 mm, Spiral bevel gear generator - WMW Modul ZFTKK 250x5k KURVEX. Used, disconnected. Change gears included. Hsdpfx Aaoxprd Dsqsw

Condition: used, mileage: 68,500 km, power: 330 kW (448.67 HP), gearing type: automatic, fuel type: diesel, color: white, overall weight: 32,000 kg, axle configuration: 8x4, number of seats: 2, first registration: 02/2023, emission class: euro6, brakes: engine braking, suspension: steel, loading space volume: 14 m³, loading space length: 5,600 mm, loading space width: 2,380 mm, loading space height: 1,000 mm, driver cabin: sleeper cab, wheelbase: 4,550 mm, Equipment: ABS, air conditioning, cabin, central locking, cruise control, differential lock, fog lights, onboard computer, parking heater, power assisted steering, seat heater, traction control, Vehicle location: incoming / in transit, ClassicSpace, Mercedes PowerShift 3, steel body, large cab, 1x comfort seat, 1x bunk, seat heating, rear window, electric mirrors, heated mirrors, electric window left, electric window right, air conditioning, sun visor, cruise control, auxiliary heater, ABS (anti-lock braking system), traction control system (ASR), constant throttle, PTO (power take-off), differential lock, fog lights, leaf suspension, Bordmatik left, aluminum tank, 2nd axle steered (leading axle), underrun protection, chute, roof hatch, green environmental sticker. Wheelbase: 4,550 mm Hodpjxn Au Djfx Aaqow Body: Meiller three-way tipper body with Bordmatik left, 7.5 t front axle, rear axle bevel gear 300 planetary 13.4 t, electronic braking system with ABS and ASR, disc brakes with full cover on front and rear axles, ABS switchable, electronic parking brake, condensate monitoring for compressed air system, rear axle stabilizer, smoker package, lower comfort bed, residual heat utilization, additional hot water heater, extra thermal insulation, construction site filter, reverse warning system, ClassicSpace, comfort central locking system, off-road drive program, multimedia radio with touchscreen, Classic Cockpit, preparation for toll collection, daytime running lights, high-performance engine brake, skid plate under bumper, transmission oil cooling, Meiller 9-piston pump type 296/54, Mercedes PowerShift 3, tank capacity: 320 l, MB 131-2c PTO pump, refrigerator, 7 mm tipping body floor. All information without guarantee as the vehicle is currently in transit! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted!

Condition: good (used), Year of construction: 2013, operating hours: 63,000 h, functionality: fully functional, We are offering 1 × KLINGELBERG used bevel gear grinding machine. Manufacturer: KLINGELNBERG AG Brand: KLINGELNBERG OERLIKON Model / Series: G 27 Year of manufacture: 2013 Type: Bevel Gear Grinding Machine Condition: Excellent / precise tolerances Applications: Spiral bevel gears, hypoid gears, planetary gear sets Industries: Transmission manufacturing, passenger car gearboxes, commercial vehicle and agricultural machinery gear units, forklift transmissions, special gearboxes, helicopter drives, etc. Technical specifications: - Max. gear diameter: 300 mm - Maximum module: 8 - Minimum module: 0.7 - CNC control: SIEMENS SINUMERIK 840 D solution line (latest software options!) - Min./max. pitch cone angle: −90 / +90° - Workpiece spindle bore: 127 mm - Grinding wheel diameter: 50 – 230 mm - Continuously variable spindle speed: 7,500 rpm - Workpiece spindle speed: 700 rpm - Total connected load: 146 kW - Machine weight: approx. 21 t - Machine dimensions: approx. 9.5 × 3.6 × 3.1 m - Integrated probe in grinding head - External spindle cooling - ELBARON integrated oil mist extraction system - HOFFMANN coolant filtration system for each machine The machine achieves outstanding tolerances and is ready for dismantling 14 days after conclusion of contract. Hedpfx Ajxg Ib Teaqjw Currently under power and available for demonstration. KLINGELNBERG inspection reports, demonstrating perfect results (and exact geometry), are available digitally and can be sent upon request. Please inquire for further details.

Condition: new, Year of construction: 2025, Number of motors 2 Stück 0 3000 mm Control ja/CNC loading dimensions L x W x H 4000 x 1500 x 1500 mm Weight 800 kg HECHT double miter saw Exenso DS350E - 3000 mm ----- For wooden glass strips, rungs, profile strips, aluminum strips, etc. Pos. 1.1 Article number 942.5103 1 piece HECHT Exenso DS350E - Working length 3000 mm - Swivel range 22.5° (inside) to 135° (outside) - Right head movable - Saw blade holder Ø 350 mm - Incl. 1 piece center support. Hjdpfovzt D Tex Aaqjw - Units clamped pneumatically. - Positioning control Exenso DS3 with touch panel 15" display in dust-proof monitor housing. - 3-axis control, 1 longitudinal axis and 2 swivel axes. - Entering the cutting data by hand - Processing data from a cutting list (data set according to specification) - Processing measuring rod data (GMF wireless caliper) - Ethernet connection 10/100 (TCP/IP) - USB interface - Incl. control cabinet, motor and software licenses. Item 1.2 Item number 723.0121 2nd DS saw blade wood Bevel/bevel/flat tooth - positive Item 1.3 Item number 942.5236 2 sets of DS workpiece clamping combined Combined workpiece clamping consisting of: Pneumatic swivel clamp - for clamping the material from above. (Free access to the work table) Pneumatic horizontal clamp - anti-twist clamping cylinder with pressure piece. The clamps can be selected individually via the saw control. The clamping sequence can also be set via the control. Including safety pre-tensioning pressure Scope of delivery for 2 sets: - 2 pieces (left/right) vertical swivel clamps. - 2 pieces (left/right) horizontal clamps. Item 1.4 Article number 942.5997 DS pneumatic feed device Item 1.5 Article number 945.2007 Packaging DS350 (transport frame) ----- Total price in this version - on request! ----- ALTERNATIVE options, prices on request! ----- For horizontal clamping of the remaining pieces with blunt glass strips instead of the 2nd set Item 1.3 943.5236 DS workpiece clamping combined! Pos. 2.1 Article number 942.5201 ES / DS workpiece clamping from the front - 2 clamping cylinders with anti-twist protection - 2 cylinder holders with clamping lever ----- For rebated glass strips, instead of standard panels without a groove: Pos. 2.2 Article number 942.5241 DS350 table supports grooved according to customer sample The assembled table supports are milled according to the customer's drawing. Please send us all profile drawings that are to be sawn (pdf, dxf and hand samples) ----- If, for example, aluminum is also to be sawn: Item 2.3 Article number 942.5203 DS hydropneumatic feed device (instead of pneumatic feed cylinder) ----- OPTIONAL accessories, with additional charge on request: ----- Item 2.4 Article number 942.5237 DS "Excess length" software (subsequent steps must be confirmed) Sequence control including hardware. After entering a cutting dimension > max. cutting length of the system, the cutting is carried out in a cyclical manner. (Left unit cuts, right unit moves the material and cuts to size.) ----- Item 2.5 Article number 944.1023 GMF caliper 3000mm complete set (1500mm plus extension 1500mm) incl. charger and receiver. A robust aluminum measuring rail with a measuring ran...

Condition: new, empty load weight: 2,850 kg, maximum load weight: 7,650 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 5,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245/70 R 17,5, color: other, gearing type: other, front tire size: 245/70 R 17,5, rear tire size: 245/70 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Each ramp approx. 2,700 mm long x 560 mm wide, ramps with grating, loading height: 840 mm, 10 lashing eyes each 2.5 t, 8 x lashing eyes each 6 t, steel side walls, foldable and removable, wood planks 50 mm, loading surface at rear beveled, inside loading width 2,480 mm, rear stanchion removable, front open for through-loading, Also available with a loading length of 6,300 mm!!, Rental price from 500 ¤, -- Printing errors, mistakes, and changes reserved, sample pictures --, More data at: !, More details: ! Hsdpfsxf Ty Ssx Aaqjw

Condition: new, empty load weight: 2,980 kg, maximum load weight: 7,520 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 6,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245 / 70 R 17,5, wheelbase: 990 mm, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, each ramp approx. 2,700 mm long x 560 mm wide, ramps with gratings, loading height: 840 mm, 12 lashing eyes each 2.5 t, 8 x lashing eyes each 6 t, steel drop sides, foldable and removable, wooden planks 50 mm, loading area rear beveled, loading area width inside 2.480 mm, rear stanchion removable, front for through-loading, , Also available in 5,300 mm loading area length! , , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Hjdpfxoxf T A He Aaqsw

Condition: new, empty load weight: 3,120 kg, maximum load weight: 8,780 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245 / 70 R 17,5, wheelbase: 990 mm, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, each ramp approx. 2700 mm long x 900 mm wide, ramps with gratings, loading height: 840 mm, 12 lashing eyes each 2.5 t, 8 x lashing eyes each 6 t, steel side walls, foldable and removable, wooden planks 50 mm, loading area bevelled at the rear, inside loading area width 2480 mm, rear stanchion removable, front for through-loading, , Also available with 5300 mm loading area length!!, , Rental price from 500 ¤, , --  Subject to printing errors, mistakes and changes, Sample images --, More data at: !, More details: ! Hedpoxf Tzvsfx Aaqsw

Condition: new, empty load weight: 2,980 kg, maximum load weight: 10,020 kg, overall weight: 13,000 kg, axle configuration: 2 axles, loading space length: 6,280 mm, loading space width: 2,480 mm, suspension: steel, color: other, gearing type: other, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, each ramp approx. 2,700 mm long x 560 mm wide, ramps with gratings, loading height: 840 mm, 12 lashing eyes each 2.5 t, 8 x lashing eyes each 6 t, steel drop sides, foldable and removable, wooden planks 50 mm, loading area rear beveled, loading area width inside 2.480 mm, rear stanchion removable, front for through-loading, , Also available in 5,300 mm loading area length!!!, , Rental price from 550 ¤, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Hsdsxf T Agjpfx Aaqew