Used Corner Connection Press for sale (26,111)

Condition: used, Year of construction: 2021, machine/vehicle number: HB 2022-A-073, pressing force: 300 t, Portal straightening press with 300 T capacity a) idle and pressing speed up to 17 mm/sec. b) opening speed up to 55 mm/sec c) table size 2500x1600mm d) open height 700 mm e) total size approx. LBH 4500 x 2300 x 3700 mm f) Oil temperature indicator on the tank g) Lubrication via grease nipple h) table in grid construction,with T grooves according to customer's request, otherwise 22mm i) operation on swivel arm, mounted on the bridge j) pressure adjustment from 50 T to 300 T via MONITOR k) bridge moves by two gear motors, via racks l) Cylinder moves to the left and to the right via toothed racks m) Machine body double painted n) Cylinder induction hardened Type of construction Press design PORTAL PRESS Thermally neutral 80 - 120 °C Number of operating sides 3 side Forces Pressing force max. 3,000 kN Free ripping force max. 500 kN Pressure build-up time Closed die Steel to steel Max. 3 sec. Dimensions Max. Opening width 700 mm Stroke and min. opening 700 mm/ 0 mm Table height above floor approx. 9ß0 mm Height above floor (headroom) approx. 3700 mm Hall height min. 5.000 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.8 mm/m Weight Total weight of press without operating materials and table plate approx. 22 T Speeds Fast closing with 17 mm sec. Pressing speed 8 mm sec. Opening 55 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel after max. 78 db(A) DIN 45635-T16-KL3 Hydraulics Number of pressing cylinders 1 pc. Operating pressure max. 350 bar Isdpfxeh Agnuj Ac Ejtk Pressing pressure build-up time 02. mz sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH approx. 93 L/min Oil volume approx. HLPD 46 MW 900 liters Ambient temperature max. 45 °C Oil temperature max. 55 °C Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Hydraulic connection Main motor IE3 22 kW Total connection Approx. 30 kW

Condition: used, Year of construction: 2019, machine/vehicle number: 138716, functionality: fully functional, power: 2.3 kW (3.13 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, total length: 900 mm, total width: 930 mm, total height: 1,850 mm, overall weight: 260 kg, Equipment: CE marking, MACPI 321.715 Industrial Garment Pressing / Finishing Machine (2019) Professional Steam-Pneumatic Finishing Machine for Jeans, Trousers & Workwear The MACPI 321.715 is a professional industrial trouser finishing machine manufactured by MACPI S.p.A., Italy in 2019. Designed for high-volume garment manufacturing, the machine combines steam, compressed air, and pneumatic tensioning to produce consistent, high-quality finishing results for jeans, trousers, chinos, and workwear garments. The unit has been used in professional garment production and remained fully operational until factory shutdown. The machine was tested and video recorded in operation on 05.03.2026. Technical Specifications • Manufacturer: MACPI S.p.A. • Model: 321.715 • Machine Type: Industrial Trouser Finisher • Year: 2019 • Serial Number: 138716 • Country of Manufacture: Italy • Weight: Approximately 260 kg • Power Supply: 400 V, 3-Phase, 50 Hz • Heating System: External Steam Supply • Pneumatic System: External Compressed Air Required • Drive System: Panasonic VF200 Inverter • Control System: Electronic Digital Control Interface Key Features • Professional steam-pneumatic finishing system • Designed for jeans, trousers, chinos, and workwear • Pneumatic garment tensioning system • Adjustable steam and air cycle parameters • Multi-zone finishing process • Digital electronic controls • Panasonic inverter drive • Foot pedal operation • Heavy-duty industrial steel construction • Designed for continuous production environments Includes • MACPI 321.715 finishing machine • Electronic control panel • Panasonic VF200 inverter • Pneumatic clamping system • Steam connection interfaces • Industrial frame • Foot pedal controls • Integrated safety guards Applications • Jeans finishing • Trouser finishing • Chino production • Workwear finishing • Uniform production • Garment manufacturing • Textile finishing departments Itsdpfxezidfgj Ac Ejk • Industrial apparel production Condition • Fully functional • Previously used in professional garment production • Tested and video recorded in operation on 05.03.2026 • Serviced on 27.02.2026 • Good industrial condition • Normal cosmetic wear consistent with factory use • Available for inspection before dismantling Location Valga, Estonia Dismantling & Transport Buyer is responsible for disconnecting steam, compressed air, and electrical connections, dismantling, loading, transportation, and all related costs. Professional dismantling is recommended due to the machine's industrial utility connections. Sales Terms Sold as-is, where-is, without warranty. Part of the MASI JEANS factory liquidation.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, power: 22 kW (29.91 HP), input voltage: 400 V, input current: 32 A, type of input current: three-phase, pressing force: 20 t, total length: 2,400 mm, total width: 1,500 mm, total height: 2,400 mm, overall weight: 2,000 kg, ambient temperature (min.): 10 °C, ambient temperature (max.): 40 °C, control cabinet length: 60 mm, control cabinet width: 80 mm, height adjustment type: hydraulic, Equipment: documentation/manual, Hidrobrasil Tablet Press – 20 t – C-Frame – Manual Loading Press For sale is a hydraulic single-column press (C-frame) from Hidrobrasil with a pressing force of 20 t, specifically designed for applications in the pharmaceutical and chemical industries. The machine is ideally suited for the production of tablets, as well as for precise pressing and forming tasks in smaller batch production and laboratory applications. ==== Technical Data & Information: Hydraulic Tablet Press – 20 t ==== General Information - Manufacturer: Hidrobrasil - Model: Single-Column Press - Machine type: Tablet Press - Design: C-Frame / Single-Column Press - Year of manufacture: 2023 - Location: Gelsenkirchen, Germany - Pressing force: max. 20 t - Machine weight: approx. 2 t - Total height: approx. 2,400 mm ==== Working Area - Max. opening width: 500 mm - Stroke / min. opening: 400 / 100 mm - Table height above floor: 800 mm ==== Speeds - Rapid closing: 120 mm/sec Ijdpfx Acetv Ewdj Eotk - Pressing speed: 5–10 mm/sec ==== Hydraulics & Drive - Operating pressure: max. 250 bar - Pressure accuracy: ±5 bar - Main pump: Gear pump, approx. 10 l/min - Oil volume: approx. 150 l (HLP 46) - Main motor: 22 kW - Total connected load: approx. 6 kW ==== Precision & Stability - Parallelism deviation: ±0.1 mm at 20 °C - Deflection: max. 0.3 mm/m ==== Control & Safety - Control voltage: 24 V DC - Light barriers: SICK / Pilz / Schmersal - Two-hand control, optionally foot control - Safety design complies with EU standards and UVV ==== Equipment - Table top designed as a tray with 50 mm edge and drain - Position adjustment via sensors - Pressure adjustment: 5–20 t via rotary control - Control cabinet mounted on the right, protection class IP54 ==== Production & Features - Multi-tool: 8 pressing cylinders - Output: approx. 8–12 parts per minute - Hydraulic unit fully removable for maintenance ===== Tablet production, pharmaceutical industry, chemical applications, laboratory presses, small batch manufacturing Hydraulic press, tablet press, single-column press, C-frame press, pharma press, laboratory press Are you looking for a hydraulic press tailored to your specific application? Contact us for a customized quote. Our hydraulic presses are manufactured according to German and European machinery directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements as they comply with all aspects of the Brazilian national safety directive NR 12, which is based on these standards. Our main strength is custom machine building and press automation. We offer bespoke hydraulic presses at surprisingly affordable prices. We primarily use components from leading European manufacturers for the hydraulic systems of our presses.

Condition: used, with new Mylar film used, in good condition Brand: Joos Year of manufacture: 1981 Machine no.: 81/10621 1 level GS certified Plate size approx. 2550 mm x 1350 mm Opening width approx. 400 mm Tip control Swivel control panel Lower safety bar Side guide Electric heating Max. pressing force 90 t Aluminium plates Itjdpjww Nd Hsfx Ac Ejk Piston diameter 80 mm Required space approx. 3000 mm x 1600 mm x 2100 mm Weight approx. 3000 kg Total connected heating load 20 kW Location: 97447 Gerolzhofen, loaded free on truck, unpacked Delivery in as-inspected condition, without warranty or guarantee.

Condition: used, Press machine, REMS Power-Press XL ACC, used equipment Manufacturer: Rems Type: Power-Press XL ACC Pressing range: Ø 10 – 108 mm (up to 110 mm) Pressing force: 32 kN Motor: 450 W universal motor Power supply: 230 V or 110 V, 50–60 Hz Weight: approx. 5.5 kg Dimensions (H x W x D): 800 x 335 x 230 mm Cable length: 2900 mm Accessories: more than 400 types of REMS pressing jaws, adapters for other manufacturers Additional features: Itsdpsxlp T Iefx Ac Eek Automatic retraction (Automatic Circuit Control – ACC) Rotatable pressing jaw holder with automatic lock Compatible with pressing jaws from other manufacturers Fast pressing, e.g., Geberit Mapress stainless steel Ø 108 mm connection in 15 seconds Press jaws: 76.1; 88.9; 108 mm

Condition: ready for operation (used), A Schenk Orion filter press with a deflection chamber is available. Number of plates: 85, frame: 100, plate dimensions X/Y: 600mm/600mm, max. filter area with 80 plates: approx. 22m², pipe connection diameter: 50mm, throughput capacity: approx. 30hl-45hl/h, max. throughput capacity: approx. 75hl/h. An on site inspection is possible. Itodox Sywtjpfx Ac Eok

Year of construction: 1992, operating hours: 100 h, condition: used, functionality: fully functional, Description Corner crimper for pressing profiles with a height of up to 68 mm. Extremely high pressing force achieved by a large-volume bellows cylinder (maintenance-free). The machine is easy to adjust and operate. Counter bearing pneumatically positionable with mechanical locking Support arms and pressing blades included as standard Two-hand operation for safe use Options Additional support Special pressing blade Technical Data Pressing height: 68 mm Pressing force: 40 kN (4 t) Drive: Pneumatic Compressed air supply: 7 bar Air consumption per cycle: 30 l Dimensions (L × D × H): 650 × 820 × 1,270 mm Weight: 205 kg Itedpfx Aox Rvl Roc Ejk

Year of construction: 1987, condition: good (used), Brand: Collin Pilot & Lab Solutions Model: P300 Presse Year of construction: 1987 Plate dimensions: 296 x 296 mm Machine no.: 6300 22 86 Connected load: 18 kW Dimensions (LxWxH): 1,150 x 530 x 1,750 mm Weight: 650 kg Iodpfx Asycggboc Estk

Condition: used, Year of construction: 2003, Filter area: 50 m² Exhaust connection: 300 mm D Dimensions: 1650 x 1580 x 3550 mm Weight: approx. 500 kg Substructure with discharge screw: Motor: 1.5 kW Briquette press Schuko C 800 - 2 Connection value: 3 kW Throughput: approx. 35 - 55 kg/h, depending on the material Itsdpfxezb N T Ue Ac Esk With extinguishing system Weight: approx. 1200 kg Storage location: Nattheim

Condition: used, Year of construction: 1991, Used frame press pneumatic Working size 3500 x 2500 mm with center pressure beam absolute angular accuracy without correction comfortable working height due to adjustable press corners Itodpfxew I Un Re Ac Eok operation of the working cylinders via 2 compressed air valves all press corners are adjustable pressure adjustable from 0-15 bar Availability: short-term Storage location: Röllbach

Condition: used, Year of construction: 1950, machine/vehicle number: 26284, functionality: unexamined, power: 1.6 kW (2.18 HP), pressing force: 30 t, overall weight: 1,100 kg, We offer this used Raskin 30TRG crank press, year of construction 1950. Machine has not been used for 30+ years and was sitting in a corner of the workshop under a tarp. Now it must go. Itedeza En Sspfx Ac Eok Untested and condition unknown, but was working when put aside, and externally looks in working order. Included is the punching tooling visible on the pictures (on the pallet + cardboard box).

Condition: as good as new (ex-display), Year of construction: 2021, functionality: fully functional, machine/vehicle number: W202001, table length: 800 mm, table width: 550 mm, Equipment: documentation/manual, H-Frame Press – 30 t – Double-column Press – 800 × 550 mm – Versatile Assembly & Production Press For sale: hydraulic double-column press (H-frame press) with a pressing force of 30 t. The machine is highly versatile and can be used as an assembly press, small batch press, hand-loading press, vulcanizing press, or heated platen press. This is an approximately 2.5-year-old, unused machine with zero operating hours, offered with full warranty. Inspection is possible at our warehouse in Ennepetal. ===== Technical Specifications & Information: Hydraulic Double-Column Press – 30 t ==== General Information - Design: Double-column press (H-frame) - Pressing force: 5–30 t (adjustable) - Machine weight: approx. 2,000 kg - Paint finish: RAL 7035 (Light Grey) / RAL 2009 (Orange) ==== Working Area - Table size: 800 × 550 mm (additional variant: 700 × 500 × 70 mm) - Ram plate: 700 × 500 × 80 mm - Max. distance table/ram: 500 mm - Stroke: 500 mm - Front opening width: 820 mm - Table height: 800 mm ==== Speeds - Approach speed: approx. 45–50 mm/sec - Return speed: approx. 40–55 mm/sec ==== Hydraulics - Operating pressure: up to 300 bar - Hydraulic pump: ASC, 28.5 l/min - Motor power: 11 kW - Oil tank: approx. 100 l - Valves: Bosch Rexroth ==== Construction & Guidance - Cylinder: Ø 110 mm (piston), Ø 70–75 mm internal - Guide columns: Ø 50 mm - Ram guided by 2 columns - Robust machine frame - Rear and side guards fully enclosed Itodpfx Acou U Ey Ie Eok ==== Control & Operation - Pressing pressure adjustable via rotary control - Adjustable two-hand operation (3 m supply cable) - Position limitation via cam switch - Travel limitation via movable sensors - Automatic positioning to defined stroke points - Resettable piece counter ==== Safety - Light curtain 500 mm (14 mm resolution, finger protection) - Reach-under protection - Optional reach-over protection - Emergency stop switch - Certified safety inspection ==== Equipment - Control cabinet technology from brand manufacturers - Illumination in press workspace - Eject chute in table ==== Options - Heated platens: 500 × 500 mm (up to 200 °C, with controller & timer) - Commissioning & operator training ==== Lead Time & Service - Delivery time: approx. 6 weeks (without heated platens) - Heated platens: approx. 8 weeks - Customer service: Dresden, Hamburg, Ennepetal, Waibstadt, Göppingen, Gelsenkirchen ===== Assembly work, small batch production, forming applications, vulcanizing, hot pressing Hydraulic press, hydraulic press, double-column press, H-frame press, assembly press, small batch press, vulcanizing press, heated platen press, industrial press Are you looking for a hydraulic press customized for your application? Contact us for a tailored offer. Our hydraulic presses are manufactured according to German and European Machinery Directives (Directive 2006/42/EC), EC regulations, and EU safety standards. Additionally, our presses exceed both Canadian and European safety requirements, as they fully comply with the Brazilian occupational safety standard NR 12, which builds upon these regulations. Our core strengths are special machine engineering and press automation. We offer custom-built hydraulic presses at surprisingly attractive prices. The hydraulic systems primarily use components from leading European manufacturers.

Condition: as good as new (ex-display), Year of construction: 2023, pressing force: 120 t, table length: 600 mm, table width: 600 mm, Here are the technical data of the offered machine: Technical data + information: HB 2021-A-188, oil hydraulic double column press 120 T bottom piston heating press. - idle speed up to 40 mm/sec - Opening speed up to 40 mm/sec - Starting press speed 5-15 mm/sec - Table size/heating plate size 600 × 600 mm - ram size/heating plate size 600 × 600 mm - 2 heating plates, electrically heated, up to 250 degrees - as OPTION - total size approx. 2000 × 1000 × 2800 mm height - Oil temperature control - Automatic lubrication - Free positioning of the ram - SICK/LEUTZE light barriers 14,1 mm on front side - Circuit oil cooling - Pressure holding valve 0 to 1800 sec. - Rear monitored door - Pressure adjustment from 30 T to 120 T - Travel limitation either by pressure or position - Programming set-up mode, single stroke (adjustable via rotary switch) - Control panel permanently installed in cabinet wall - Two-hand operation - Machine body double painted - Signal light: red: alarm, yellow baking phase, green: ready - Heating plates with electric heating rods, up to max. 250 degrees - Assembly, commissioning, instruction against separate charge Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 1,600 kN Free ripping force max. 200 kN Pressure build-up time closed die steel to steel Max. 8 sec. Dimensions Max. Opening width per compartment 200 mm Stroke and min. opening per compartment 400/200 mm Table height above floor, without heating pl. 850 mm Height above floor (overall height) approx. 2.800 mm Hall height min. 3,500 mm Iodpfx Acok S Dt Tj Ejtk Parallel deviation at 20 °C +/- 0.1 mm Deflection Determined at max. clamping force with 70 % occupancy ≤ 0.2 mm/m Total weight of the press without operating materials approx. 9 to Accessories: 4 HEATING PLATES 500 × 400 mm, max. heating capacity Equipped with temperature sensor 300 degrees Speeds Fast closing with 15 mm sec. Pressing speed 10 mm sec. Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 8 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 240 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH gear pump approx. 48 L/min Oil volume approx. HLP 46 MW 300 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Automatic pressure readjustment after 5 % pressure loss Pressure stabilization for up to 1800 sec. Electrical system Main supply 400 V AC Control voltage Hydraulic pumps 24 V DC 24 V DC Frequency 50 Hz Connection hydraulic main motor 15 kW Total connection approx. without heating plates 19 kW ##### If the press does not exactly meet your requirements, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Our great strength is special machine construction and press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Year of construction: 2018, condition: used, Screw compressor Manufacturer: Renner Type: RS132D Year of manufacture: 2018 Technical data - Main drive motor: direct drive of the compressor stages via a shaft coupling - Oil filter / thermostat unit: regulates the cooling of the compressor oil and filters it - Oil-injected compressor stage: compressed air generation - Suction regulator: regulates the amount of air drawn in by the compressor - Control cabinet: controls and regulates the compressor system - Suction air filter: filters the air drawn in - Radial fans: generate cooling air for the oil and compressed air coolers - Compressed air outlet: connection point for an external compressed air network - Minimum pressure retaining valve: maintains a minimum system pressure for oil supply, separates network / system pressure - Fine oil separator with oil suction line, sight glasses, and check valve: oil separation via air-oil filter cartridges, return of separated oil from the compressed air - Safety valve: relieves pressure in case of overpressure - Oil filler plug with oil level monitoring: electronic oil level monitoring - Oil drain: drains the oil reservoir - Compressed air / oil combined cooler: cools the compressed air and the compressor oil - Control system: RENNERtronic - Integrated standby heater Compressor - Counterclockwise rotation (without gearbox) / Clockwise rotation (with gearbox) Suction regulator The suction regulator is mounted directly on the screw compressor. It regulates the volume flow of air drawn in by the screw compressor through the suction filter. Operating principle of the suction regulator: The suction regulator has only one main valve. This valve operates as a stepless control valve as well as a tightly closing shut-off valve. In full-load operation, the suction cross-section is fully open with minimal pressure drop. In part-load operation, the suction cross-section is automatically regulated by limiting the stroke and adjusted to the actual air requirement. When the system is stopped, this valve quickly and automatically closes the entire suction cross-section completely. The multiple functions of the regulator are initiated by only one control unit. Minimum pressure retaining valve Iedpfxozu Aibo Ac Eotk The minimum pressure valve is located at the compressed air inlet of the air aftercooler. It performs two functions: 1) As a pressure retaining valve, it prevents the pressure from dropping below a minimum overpressure of 4.5 bar when there is no back pressure. This pressure is necessary to ensure the oil supply to the compressor. At the same time, this minimum overpressure is required for good oil separation. 2) As a check valve, it prevents the backflow of compressed air from the compressed air network or the pressure vessel into the compressor system. This allows the separator vessel to be completely relieved when the system is shut down. The valve operates automatically. Adjustment of the minimum pressure valve may only be carried out by personnel authorized by the manufacturer! Suction air filter The suction air filter is installed in the housing and connected to the suction regulator via a ventilation hose. The micro-dry filter with a fineness of 10 μm is used to filter the suction air. The filter can be cleaned several times before it needs to be replaced. Use only original replacement filters! Pressure transmitter The pressure transmitter, used in all systems with electronic control (RENNERtronic / -Plus), is connected to the compressed air outlet (network press

Condition: new, Year of construction: 2021, pressing force: 10 t, Single-column press – Manufacturer Hidrobrasil – 10 t Assembly press – Table 600 × 300 mm For sale is a hydraulic single-column press (C-frame) from the manufacturer Hidrobrasil with a pressing force of up to 10 t. The machine is designed for continuous shift operation and impresses with its robust construction, reliable hydraulic components, and flexible application possibilities in assembly and pressing processes. ===== Technical data + information: Hydraulic single-column press – 10 t ==== General information - Manufacturer: Hidrobrasil - Model: Single-column press / Assembly press - Design: C-frame press / Single-column press - Pressing force: max. 10 t (100 kN) - Machine weight: approx. 1.2 t - Dimensions (L × W × H): approx. 1,100 × 600 × 1,850 mm - Table height: 850 mm - Control sides: 1 ==== Working area - Max. opening width: 400 mm - Stroke: 350 mm ==== Table & Ram - Table plate: 600 × 300 mm - Ram plate: 300 × 300 mm - Design: with T-slots and central cylinder tension ==== Speeds - Forward speed: 0 – 10 mm/s - Return speed: up to 25 mm/s - Pressing speed: 0 – 10 mm/s ==== Hydraulics - Number of cylinders: 1 - Operating pressure: max. 250 bar - Pressure accuracy: ± 5 bar - Pump: Gear pump, approx. 6 l/min - Oil volume: approx. 80 l (HLP 46) ==== Drive & Electrical System - Motor power: 2.2 kW - Total connected power: approx. 3 kW - Main supply: 400 V AC - Control voltage: 24 V DC - Frequency: 50 Hz ==== Equipment & Operation - Pressure setting via rotary control (0.5 – 10 t) - Cable remote control for upward and downward movement - Oil temperature display Isdpfxehaqyge Ac Estk - Control cabinet cable: 3,000 mm cable with 16 A plug - Machine body powder-coated / double-coated ==== Control & Components - Control system: Siemens - Hydraulic components: Bosch Rexroth ==== Design & Safety - Robust machine body according to DIN 8651 - Cylinder induction-hardened and chrome-plated - CE certificate available - Documentation in German - Low maintenance and reliable - Complies with current EU directives ===== Assembly work, pressing work, small series production, workshop applications, light forming technology Single-column press, C-press, hydraulic press, workshop press, pressing press, industrial press, tool tryout press Are you looking for a hydraulic press tailored to your specific application? Contact us for an individual offer. Our hydraulic presses are manufactured according to German Machinery Directives as well as European Machinery Directives (Directive 2006/42/EC), the EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements, as they comply with all points of the national Brazilian safety regulation NR 12, which is based on these. Our strength lies in special machine construction and press automation. We distribute customized hydraulic presses at surprisingly affordable prices. For the hydraulics of the presses, components from leading European manufacturers are mainly used.

Year of construction: 2001, condition: ready for operation (used), Max. pressing force: 1000kN, max. working length: 3100mm, throat depth: 250mm, connected load: 18kW, weight: 9.5t, operational hours counter: 76,566h, with accessories and documentation, was maintained regularly. Itjdpfxslzizms Ac Eok

Condition: excellent (used), Catalogue number 7732 TECHNICAL DATA - pressing force: hydraulic - briquette shape: round - briquette diameter: 70mm - tank diameter: 1200mm - output: approx. 70kg/h - fully automatic machine operation - motor: 7.5kW - max working pressure: 150 bar - suction outlet diameter: 90mm - filter bag opening diameter: 500mm - max bag height: 900mm - dimensions (LxWxH): 1950x1400x2700mm - weight: 1130kg Itodpfxozhvaas Ac Eok ADVANTAGES - Italian-made - direct connection to sawdust extraction possible - used briquetting press - operating & maintenance documentation (DTR) - condition: very good Net price: 29,900 PLN Net price: 7,120 EUR (based on 4.2 EUR exchange rate) (Prices may vary with significant exchange rate fluctuations)

Condition: new, Year of construction: 2026, pressing force: 20 t, DURENDUS 20 T Workshop Press – C-Frame Press – 600 mm Clear Width, 400 mm Stroke The machine shown here was built and delivered to a customer as a custom order. We can supply this machine from stock or manufacture it as new – including custom options per your requirements. This is a hydraulic workshop press suitable for pressing, straightening, and assembly tasks in both workshop and industrial environments. Base Price: €3,120 net Options (on request): The listed options are based on implemented customer projects and allow targeted adaptation of the machine to the specific application. The base machine is already a functional standard version – in practice, it is commonly extended with additional features and configured to project-specific requirements. * Table plate with X-form T-slot (from 60 t) * Pressure adjustment * Lateral movement of the ram (from 60 t) * Bending tool (from 60 t) * Anti-rotation cylinder with manual stroke setting * V-profile straightening support in combination with table plate * LED lighting * Foot switch * Cooling ===== Technical Data & Information: ==== General Information * Design: Workshop press * Press force: 20 t (optionally adjustable) * Total weight: approx. 350 kg * Overall dimensions (W × D × H): 1,100 × 700 × 2,350 mm ==== Working Area * Clear width: 600 mm * Open depth: 200 mm Itodpfx Acey E Nnns Ejk * Installation height: 250–900 mm (variable) ==== Table & Ram * Crossbeam usable width: 600 / 470 mm * Ram stroke: 400 mm * Cylinder diameter: Ø 90 mm * Piston rod: Ø 50 mm * Height adjustment: via chain mechanism ==== Speeds * Idle speed: 7.8 mm/s * Return speed: 11.3 mm/s ==== Hydraulics & Drive * Pump capacity: 3 l/min * Motor output: 0.75 kW * Hydraulic tank: 12 l * Pressure accuracy: ±5 bar * Hydraulic system: DUPLOMATIC ==== Control & Operation * Manual lever operation * Fine adjustment via hand lever * Power connection: 400 V / 50 Hz * Total connected load: approx. 1 kW ==== Equipment * Height-adjustable crossbeam with bolt locking * Chain mechanism for table adjustment * Manometer for pressure display * Emergency stop button * CE certification * Double-layer coating according to RAL ===== Pressing, extraction, assembly work, straightening, workshop applications, maintenance Workshop press, hydraulic press, C-frame press, C-type press, assembly press, straightening press, industrial press Are you looking for a hydraulic press tailored to your specific application? Contact us for a customized offer. Our hydraulic presses are manufactured in compliance with German machinery directives as well as European machinery directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety standards, as they fully comply with the Brazilian national safety guideline NR 12 – which builds upon both. Our key strength lies in special purpose machine construction and press automation. We supply tailor-made hydraulic presses at surprisingly affordable prices. Our presses are predominantly equipped with hydraulic components from leading European manufacturers.

Condition: good (used), functionality: fully functional, High-frequency press for glulam beams up to 22 meters maximum pressing width: 1300 mm maximum pressing thickness: 300 mm loading conveyor Itsdpfow A Hk Iex Ac Ejk 3,000 mm press with section-by-section polymerization (3 meters each)

Condition: new, Year of construction: 2025, pressing force: 20 t, Forging Press – Manufacturer Durendus – DCS-20 – 5–20 t C-Frame Press – Table 500 × 600 mm For sale is a compact single-column forging press (C-frame) from the manufacturer Durendus, model DCS-20, with an adjustable pressing force of 5 to 20 t. This machine features a table size of 500 × 600 mm, a maximum installation height of 700 mm, high traverse speeds, and is ideally suited for small-scale forging, forming, and assembly work. ===== Technical Data & Information: Forging Press Durendus DCS-20 – 5–20 t Single-Column Press ==== General Information - Manufacturer: Durendus - Model: DCS-20 - Design: Single-column press / C-frame - Pressing force: 5 – 20 t (adjustable) - Machine weight: approx. 1,900 kg - Dimensions (W × D × H): 1,450 × 1,500 × 2,400 mm ==== Working Area - Max. installation height: 700 mm - Stroke: 0 – 500 mm (adjustable) - Table height: 800 mm ==== Table and Ram - Table size: 500 × 600 mm - Ram size: 500 × 600 mm - T-slots: DIN 650 – 18 mm (or as per customer specification) ==== Hydraulic Cylinder - Cylinder diameter: Ø 90 mm Itodpeyght Rjfx Ac Ejk - Piston rod diameter: Ø 60 mm - Rapid traverse cylinder: Ø 40 mm - Rapid traverse piston rod: Ø 25 mm - Operating pressure: max. 250 bar (adjustable) ==== Speeds - Return speed: 140 mm/s - Idle speed: 140 mm/s - Pressing speed: 4 – 10 mm/s (adjustable) - Pressure build-up time: max. 2 s (steel on steel) ==== Hydraulics - Hydraulic pump: Rexroth, 22 l/min - Motor power: 7.5 kW - Oil tank capacity: 150 l - Hydraulic block / valves: Hydropack - Filter: Filtrec - Oil level monitoring: electronic oil level switch - Hydraulic power unit: mounted at the upper rear ==== Electrical - Main power supply: 400 V AC - Control voltage: 24 V DC - Frequency: 50 Hz - Connected load: approx. 10 kW ===== Forging, forming technology, assembly work, small batch production, workshop applications, metalworking Forging press, single-column press, C-frame press, hydraulic press, forming press, workshop press, small press Are you looking for a hydraulic press tailored to your application? Contact us for a customized quote. Our hydraulic presses are manufactured according to German machinery directives, as well as European machine guidelines (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed both Canadian and European safety requirements as they fully comply with the Brazilian national safety directive NR 12, which is based on these standards. Our key strengths are special machine construction and press automation. We supply custom-made hydraulic presses at surprisingly affordable prices. The hydraulic systems of our presses are predominantly equipped with components from leading European manufacturers.

Condition: excellent (used), MDS Type: MDS A220-PD MDS A220-PD Manual Assembly Station The A220-PD assembly system is a stationary manual assembly station for processing press-fit components. Intended use: The machine is used for press-fitting connecting elements. The operator manually places the corresponding screws, plastic nuts, and the component to be processed into the machine. The operator then starts the press-fitting process using a foot switch. The press-fitting process runs automatically. Connecting elements: Press-fit nut, rivet nut, self-piercing nut, press-fit pin, punching pin/rivet pin Thread size: M5, M6, M8, M10, M12 Technical data: Control voltage: 230V/10A Connection plug: HAN 10, not wired Temperature ranges: Transport: -20°C to +60°C Operation: +10°C to +40°C Storage: -20°C to +50°C Compressed air connection: Itedpfx Acszgr I Rj Ejk Operating pressure: 6 bar Quality: Treated, water-free, and oil-free air Connection: 1/2" connection thread Machine dimensions: Length (L): approx. 824 mm / Height (H): approx. 1800 mm / Width (B): approx. 600 mm Values apply to a working height (AH) of 1000 mm. Pneumatics: Standard: Manufacturer SMC Variant: Manufacturer FESTO Control: Standard: Manufacturer B & R Variant: Manufacturer Siemens Machine type: C-frame A220-PD Continuous sound pressure level (LpA): 78 dB Operating modes: The operating modes can be changed in the control panel. Automatic mode: The press-fitting of the connecting elements takes place in automatic mode. Movements are only initiated when the operator presses the foot pedal and thus triggers the press-fitting process. Manual mode: In manual mode, adjustments are made to the machine. In this operating mode, movements can be activated individually. Weight: Approx. 600 kg Condition: used Scope of supply: (See picture) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by phone.

Year of construction: 2012, condition: used, Membrane press Manufacturer: Columbus Type: Vakuform Sonder Year of manufacture: 2012 Technical data - Must be connected to an external vacuum pump - 750 watts, 230/380V, 50 Hz - Boiler capacity: 200 l - Suction capacity: 25 m3/h - Vacuum: max. 0.85 bar - Working area: 2000 x 1350 mm Note: Iodpfxezuz Ebe Ac Estk The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: good (used), Karl Krause Hot stamping press Manufactured by Karl Krause, Germany, The machine is fully operational, after modernization of the control system. Iedjzlaalepfx Ac Estk Extendable work table. Timer control allows the machine to be started at a specific time to ensure it is ready for operation. 380V power supply. Heating plate size: 400x530mm. Weight: approx. 800kg.

Condition: new, Year of construction: 2026, CORMAK VP3000 Gluing Press The CORMAK VP3000 is an industrial hydraulic gluing press designed for precise bonding of solid wood and wood-based components. Equipped with six fully adjustable hydraulic cylinders with high pressing force, the machine ensures uniform pressure distribution and repeatable gluing results across the entire working surface. Thanks to its robust construction and advanced hydraulic system, the CORMAK VP3000 is perfectly suited for both individual production and serial manufacturing. Main advantages of the machine 6 hydraulic cylinders – each with a pressing force of 2000 kg, enabling uniform bonding of large and demanding components. Full pressure adjustment – allows precise adjustment of the clamping force according to the type and thickness of the material. Hydraulic valves with locking function – maintain constant pressure throughout the entire working cycle, ensuring reliable and consistent gluing results. Pressure gauge – enables continuous monitoring and accurate setting of operating parameters. Easy adjustment of pressing units – quick positioning of the clamping elements saves time and increases work efficiency. Steel construction – provides high stability and resistance to deformation during long-term operation. Design and technology The CORMAK VP3000 press has been designed for intensive use in industrial environments. The rigid frame made of steel profiles provides a stable base for six hydraulic pressing units. Each unit can be adjusted independently and positioned according to the operator’s requirements. The minimum distance between pressing units is 240 mm, allowing work with narrow and short components. Thanks to locking valves and an integrated pressure gauge, the operator has full control over the entire gluing process, including pressing force and pressure distribution. This solution is particularly important in factories producing glued panels, countertops, and furniture components, where connection quality and stability are essential. Precision and working efficiency One of the key advantages of the VP3000 model is its excellent repeatability – both in terms of pressing force and the accuracy of glued joints. The gluing press provides even pressure distribution over the entire working area, eliminating the risk of gaps, voids, or improperly bonded sections. The machine is simple and quick to operate and does not require extensive operator training. This allows faster implementation into production environments and improves overall manufacturing efficiency. Applications The hydraulic CORMAK VP3000 press is ideal for: gluing solid wood and laminated panels, production of furniture and structural glued panels, manufacturing worktops and cabinet fronts, bonding frame and staircase components, professional woodworking workshops and serial production facilities. Standard equipment 6 hydraulic cylinders with a pressing force of 2000 kg each, hydraulic pressure gauge, working pressure locking system, adjustable pressing units, robust steel construction. Technical specifications Parameter Specification Total height 2040 mm Total width 3000 mm Maximum clamping height 1550 mm Itodpfxjwcy U Tj Ac Esk Minimum distance between pressing units 240 mm Hole distance from pressing unit 50 mm Working pressure 6 × 2000 kg External dimensions 3030 × 450 × 660 mm Total weight 260 kg

Year of construction: 2026, condition: new, New machine Year of manufacture: 2026 The space-saving, swiveling vacuum press with a pressing area of 3500 mm x 1420 mm. Technical standard equipment of the vacuum press: Unless otherwise agreed, the vacuum press is powder-coated in RAL 7012 and RAL 7035 color shades. Custom colors are available upon request and must be clarified in advance, which may result in additional charges. Welded table construction designed for professional use, mounted on a swiveling chassis cart, standing on 4 swivel castors, surface load capacity of 150 kg. When not in use, the machine can be swiveled for space-saving storage and locked in place, reducing the required depth to only 800 mm. The table surface consists of a 22 mm thick HPL-MDF board, with a slotted vacuum distribution plate made from MDF covering the pressing area. The membrane frame is supported by 2 gas pressure springs mounted on the sides of the machine. A natural rubber membrane with 2 mm thickness, 780% elongation capability, and temperature resistance up to 70°C is installed, attached by a clamping system for efficient membrane changes. The all-around sealing of the press area is provided by a sealing profile installed in the membrane frame. Oil-circulated vacuum pump with a suction capacity of 40 m³/h and two vacuum tanks with a total capacity of 200 liters. Evacuation and ventilation of the press area is managed via a 3-way ball valve located at the front of the machine. The machine is delivered pre-assembled on a pallet. Please note that unloading requires a forklift with sufficient lifting capacity and fork length. Additionally, it is possible to book initial setup and a quick instruction by one of our staff members. If desired, we are happy to provide you with a separate offer for this service. Summary of key data: Itsdpfxoznph Re Ac Eek - Welded frame construction - Highly flexible natural rubber membrane, thickness: 2 mm, elongation: 780%, very high recovery capability, suitable for temperatures up to 70°C - MDF vacuum distribution plate - Digital vacuum control VAK-CONTROL 1 with auto shut-off - Vacuum pump: 40 m³/h, oil lubricated - Max. vacuum: -0.99 bar - Max. pressing pressure up to 9.9 t/m² - Connected load: 1.40 kW (400 Volt) - Vacuum tank: 200 liters - 4 swivel castors with locks - Additional 13 mm vacuum connection - Pressing area: 3500 x 1420 mm - Table height to vacuum distributor plate: approx. 895 mm - Machine height closed: approx. 960 mm - Machine height closed with cover plate: approx. 1030 mm - Installation dimensions, operational: 3790 x 1700 x 2150 mm (LxWxH) - Installation dimensions, swiveled: 3790 x 800 x 1750 mm (LxWxH) Commodity code: 84659400 Net weight: 570 kg Gross weight: 660 kg Includes cover plate 3514 With a cover plate, you not only protect your membrane from UV radiation, but also convert your mobile-base vacuum press into a mobile worktable that can be used flexibly in your company. - Coated cover plate - Solid welded steel frame - Opening support by gas pressure springs Commodity code: 84669280 Net weight: 105 kg Gross weight: 105 kg The cover plate is only available in combination with a vacuum press.