Used Dehumidifier for sale (63)

Condition: like new (used), Year of construction: 2022, overall weight: 250 kg, BOGE DS 350 refrigerant air dryer Rjdpfxexcb Eds Ag Iop

Condition: new, Electric dehumidifier/construction dryer for commercial use. For drying rooms, dehumidifying cellars, etc. and for drying e.g. concrete, masonry, plaster, screed. Refrigeration unit with rotary piston compressor and capacitor motor 230 V, 50 Hz, 900 W, with electronic defrosting, for continuous operation. Very quiet operation. Dehumidification capacity max. 50 l/24 h, air volume max. 265 m3/h. Electronic control unit with illuminated large control panel and memory function. Electronic hygrostat. Air filter. Internal 7.7 l condensate container. In sturdy plastic housing with castors. In cardboard box. Dehumidification capacity: ≤ 50 l/24 h Rjdpfx Aetty Raeg Iep Air volume: ≤ 265 m³/h

Condition: new, Electric dehumidifier/construction dryer for commercial use. For drying rooms, dehumidifying cellars, etc. and for drying e.g. concrete, masonry, plaster, screed. Refrigeration unit with rotary piston compressor and capacitor motor 230 V, 50 Hz, 1200 W, with automatic hot gas defrosting system, for continuous operation. Very quiet operation. Dehumidification capacity max. 80 l/24 h, air volume max. 850 m3/h. Electronic control unit with illuminated 3"" display and memory function. Electronic hygrostat, operating hours counter, power consumption counter. Air filter. In a sturdy sheet steel housing on a mobile tubular steel frame with large wheels. In cardboard box. Condensate container not included (see accessories below!) Dehumidification capacity: ≤ 80l/24h Air volume: ≤ 850 m³/h Redpsuy Thmefx Ag Ijp Super offer: When you buy a REMS Secco 80 set, you will receive 1 REMS Detect W humidity measuring device free of charge. You save an additional 233.55 euros. The offer is valid until 31.12.2024

Year of construction: 2018, condition: like new (used), REFRIGERATION DRYER AIRPRESS APX 24 OUTPUT 2.4 M3/MIN, YEAR OF PRODUCTION 2018 Rodpfsi Att Ssx Ag Ijp THE DEHUMIDIFIER IS FULLY FUNCTIONAL.

Year of construction: 2014, condition: like new (used), REFRIGERATION DRYER AIRPRESS APX 30 Redpfxoi Atudo Ag Isp CAPACITY 3 M3/MIN, YEAR OF PRODUCTION 2014 THE DEHUMIDIFIER IS FULLY FUNCTIONAL.

Condition: ready for operation (used), Year of construction: 2017, functionality: fully functional, overall weight: 128 kg, ambient temperature (max.): 46 °C, pressure (max.): 13 bar, MACHINE DETAILS Weight: 128 kg Max. air pressure: 13 bar Max. ambient temperature: 46 °C Redpfxsydnyxo Ag Isp

Year of construction: 2011, condition: good (used), warehouse no.: 503260 type / device: dehumidifying dryer manufacturer: Amboss+Langbein type: Sektionaltrockner H150 year of construction: 2011 The sectional dryers from Amboss+Langbein can be used for energy-saving, stationary and mobile drying. Thanks to the modular system from Amboss+Langbein, the drying system adapts individually to operational requirements and can be implemented in the smallest of spaces. Rjdpsx Eifksfx Ag Iop Also available with material station and vacuum system if required. The dryers work with dew point control and energy-saving heat exchangers. Depending on the production requirements, the air throughput is regulated between 140 and 400 m³/h by process control. Each drying boiler has an individual temperature control. A separate scanning of the material to be dried prevents over-drying and insufficient drying Drying due to excessive material removal. Properties: Fully insulated drying container made of V2A stainless steel Sectional multi-boiler system Each dryer boiler individual temperature control Continuous drying Automatic air volume measurement Patented throughput recording and adapted drying Protection against overload and overdrying Dew point controlled (-60 °C tested) Process air control Batch drying Energy-saving heat exchanger Extreme drying of compressed air for electronic component manufacturing

Condition: new, ME-LINE - Air-Cooled Dehumidifiers are used for drying air of up to 100% relative humidity (RH) with temperatures from +45 ºC and above. EU-LINE - Air-Cooled Dehumidifiers are used for drying air of up to 100% relative humidity (RH) with temperatures from -30 ºC to +40 ºC. Rust is the adversary of freshly blasted steel; high air humidity combined with low steel temperatures creates ideal circumstances for moisture condensation onto the recently blasted surface. Condensation rust is a major cause of early coating failure. By lowering relative humidity, the Proton dehumidifiers are designed to give the best climatic conditions for blasting. Climate conditions across the world vary considerably from chilly and humid in Western Europe, warm and humid in the Far East, to hot and humid in the Middle East. Various types of technology can be employed in the dehumidification process; certain dehumidification technologies are more successful than others in dealing with specific climatic conditions. Each Proton dehumidifier is built to the highest quality standards and comes with regional certification. The heart of the humidifier is a very efficient and robust metal silicate rotor. The rotor contains a vast number of air channels, running parallel to the shaft, which ensures a large internal surface for adsorbing water vapour. The rotor is not affected by over saturation. Therefore, the PROTON dehumidifier’s rotor can resist long time storage at high humidity without loosing capacity. The PROTON dehumidifiers have been developed especially for corrossion protection in connection with sandblasting and painting operations to protect materials and to avoid moisture problems, meeting the following conditions: •Avaliable in sizes from 1.000m³/h to 18.000m³/h dry air. •Avaliable in pre-cooled and after-cooled versions for warm climates. •Robust design with steelframe, eyebolts etc. •Vital parts can easily be maintained and exchanged. •Large air inlet grills and filters. Rjdjkw Ukujpfx Ag Ijp •Can be built into containers for protection. •Adjustable dehumidifying capacity and outlet air temperature in 4Grades. •Outdoor and indoor use. •Dry air pressure up to 1200 Pa. Technical. Spec.: Dehumidifiers differs between 1.000m3/h - 18.000m3/h.PROTON Dehumidifiers decrease the Relative Humidity (RH) from 90% to %10-15. Dehumidifiers are capable to remove 100lt water per hour.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: ES50202201047, type of input current: AC, overall weight: 36 kg, input voltage: 240 V, type of cooling: air, input frequency: 50 Hz, noise level: 52 dB, Equipment: compressor, Mobile dehumidifier for enclosed spaces. Water tank capacity 5.5 liters, refrigerant R290 (propane). Minimum room size 12 m² (floor area). Maximum room size 80 m² (floor area). Shipping is possible. Rjdpew Ecqpjfx Ag Iep

Condition: excellent (used), Year of construction: 2015, Refrigeration dryer BOGE DS 95 Rjdpfxjk Nb T Ds Ag Iop Capacity 9.5 m3/min year of manufacture 2015, THE DEHUMIDIFIER IS FULLY FUNCTIONAL.

Year of construction: 2021, condition: like new (used), For sale Food Dryer - Dehumidifier. Used a few times. Redpfx Agsibwb Te Ijp Max. indoor temperature: 60 degrees Celsius. Flow rate: 4500 m3/h Shell for products: 25 psc. Power required: 220V 50Hz More parameters in photos. If you have an questions on this, please do not hesitate to contact us.

Year of construction: 2015, condition: ready for operation (used), injection weight: 2,424 g, This Husky HPETL230E-RSE95D-95 was manufactured in 2015. It is an all-electric injection molding system with a maximum throughput of 390 kg/h PET and a max shot weight of 2424 g PET. The clamping unit is fully electric with a toggle drive, and it features an integrated control system for additional equipment. Consider the opportunity to buy this Husky HPETL230E-RSE95D-95 electrical injection moulding machine. Contact us for more information about this machine. Additional equipment • Mold Dehumidifier: Incl. hood, spare parts package, piping • Conveyor Belt: Two-sided preform filling system for cartons/grid boxes Machine Benefits Technical Machine Benefits • The package includes two machines along with additional components such as pellet silos, pellet feeder, discharge system for foreign bodies in pellets, dosing unit for color, and platform. Everything seen in the pictures is included. • Max throughput: 390 kg/h pet • Clamping unit: fully electric with toggle drive • Clamping platen: movable, guided on rollers • Type: split version • Dryer: dr815ht-g3 with 4000-liter drying hopper (stainless steel, insulated) • Husky 1: 3 tools - 28 gauge muzzle, 17. 8/26/30. 3 grams • Husky 2: 2 tools - 38 gauge muzzle, 18/29 grams Extra Information Clamping Force Clamping Unit: Fully electric with toggle drive Clamping Platen: Movable, guided on rollers Control Unit Control System: Integrated control system for additional equipment Display for Mold Cooling Water Temperature/Pressure (Flow and Return) Control Output for Color Dosing Unit Lubrication System: Automatic Post-mixing Device: Integrated in the nozzle Tools 48-cavity H-PET Injection Mold Preform Weight: 17.8 g and 30.26 g Punch Size: 50 x 140 mm Includes: 3-position removal plate, basic spare parts package 32-cavity H-PET Injection Mold Preform Weight: 18 g and 29 g (38 mm Bericap) Punch Size: 63.5 x 140 mm Includes: 3-position removal plate, basic spare parts package Functions Temperature Monitoring and Setting Continuous Level Meter Variable Dew Point Setting Conveying: Hot transport of the granulate via vacuum unit P07 to the booster hopper (HAD400) Paint Mixing Units For Solid Paint: Volumetric, 4 dosing screws For Liquid Paint: 4 dosing pumps Preform Production Specifications Preform Weight: 17.80 g Mouth: PCO1881 LW Length: 89.35 mm Wall Thickness: 3.06 mm Base: 2.30 mm Shape: Bell Cavities: 48 Cycle Time: 12.4 ±0.3 s Preforms per Hour: 13935 Annual Production (95% availability): 111205000 Throughput (kg/h): 248 Power Consumption: 506 Wh/kg PET Preform Weight: 29.00 g Mouth: Bericap 38 Length: 108.59 mm Wall Thickness: 3.16 mm Base: 2.42 mm Shape: Bell Cavities: 32 Cycle Time: 13.7 ±0.3 s Preforms per Hour: 8409 Annual Production (95% availability): 67101000 Throughput (kg/h): 244 Power Consumption: 532 Wh/kg PET Preform Weight: 18.00 g Mouth: Bericap 38 Length: 82.04 mm Wall Thickness: 2.70 mm Base: 2.20 mm Shape: Bell Cavities: 32 Cycle Time: 11.3 ±0.3 s Preforms per Hour: 10195 Annual Production (95% availability): 81353000 Throughput (kg/h): 184 Power Consumption: 506 Wh/kg PET Preform Weight: 30.26 g Rjdpfx Agox D Hvwj Iep Mouth: PCO1881 LW Length: 122.30 mm Wall Thickness: 3.00 mm Base: 2.30 mm Shape: Grade Cavities: 48 Cycle Time: 14.7 ±0.3 s Preforms per Hour: 11755 Annual Production (95% availability): 93805000 Throughput (kg/h): 356 Husky1 PCO 1881 30,3g 1-1,5l PCO 1881 26,0g 1-1,5l PCO 1881 17,8g 1-1,5l Husky2

Condition: ready for operation (used), Year of construction: 2006, travel distance X-axis: 350 mm, travel distance Y-axis: 250 mm, travel distance Z-axis: 256 mm, overall weight: 4,500 kg, number of axes: 3, This 3-axis AGIE Challenge 2 eCut wire EDM machine was manufactured in 2006. It offers precision electrical discharge machining capabilities, ideal for detailed and intricate metal work. Consider the opportunity to buy this AGIE Challenge 2 eCut wire EDM machine. Contact us for more information about this machine. Additional equipment • Wire System: Wire diameter 0.1-0.33 mm, Wire speed 60-300 mm/s, Wire tension 0-25 N, Wire spool up to 25 kg, Threading system up to 250 mm height, nozzles 1 mm and 2 mm Machine Benefits Technical Machine Benefits Rodpfx Aex D Sb Eeg Ijp • Max workpiece dimensions (wxdxh): 750 x 550 x 250 mm • Axis travels u/v: ±70 mm • Positioning speeds: manual (x/y) 30°/100 mm, programmable (x/y) exc “a” 0. 9 m/min, cha/exc “d” 3 m/min, u/v/z 0. 6 m/min • Compressed air: Ø 7 mm, 6-8 bar, 5 m³/h, filtered, dehumidified, unlubricated • Cooling water: ≤ tune level -7°c, 20 l/min, 1. 5-3 bar Extra Information Machine still under power

Condition: used, Year of construction: 1978, 10 MVA oil transformer, TuR Dresden, 30 / 10.5 kV with tap changer 19 steps, switching group YNyn0, with expander, Buchholz relay, dehumidifier, fan, dial thermometer, year of manufacture 1978 Rodpfx Aet Akl Heg Iep

Condition: used, New compressed air refrigeration dryer, unused compressed air dryer from stock Compressed air dehumidifier SMC type IDFA3E-23 Compressed air dryer, compressed air dehumidifier Serial No.: PP0213S Year of manufacture: 2011 SMC compressed air dryer IDFA size 3E Flow rate per hour: 12,000 liters/h (12 m³/h) Flow rate per minute: 200 liters/min. Operating pressure max. 10 bar Operating pressure: 0.15 to 1.0 MPa (manufacturer's specification) Refrigerant: R134a Temperature range: 5°C to 50°C Power consumption: 180 watts Power supply: 230 volts, 50 Hz, 1.2 amps Connection pipe thread: 3/8" - Stainless steel heat exchanger, air-cooled condenser - Condensate separator with automatic drain Redpfx Aoyif I Ujg Ijp - Condensate drainage via hose Space required (L x W x H): 410 x 226 x 473 mm Weight: 18 kg New, unused, in mint condition from stock

Condition: used, Year of construction: 2009, machine/vehicle number: PR21, Technical Specifications & Performance Data This Husky injection molding machine is engineered for high-volume PET preform manufacturing and is well suited for integration into a used bottling line or as a second hand addition to industrial packaging operations. The 120-ton clamping platform is paired with a 32-cavity hot runner system, enabling consistent output of PET preforms across multiple bottle formats. Manufactured by Husky in 2009, the unit is configured for rapid mold changeovers and stable cycle times, supporting beverage production with precise neck finishes and preform weights. Manufacturer: Husky Model: HyPET120 P85/95 E85 Year of manufacture: 2009 Clamping force: 120 tons Cavities: 32 Hot runner system: Husky 32-cavity hot runner, common across supplied molds Neck finishes: 29/25 mm primary; additional parts for 30/25 mm Preform weights (29/25 mm sets): 9.02 g, 12.46 g, 18.70 g Additional 30/25 mm parts: 10.5 g, 14.0 g, 22.0 g, 25.0 g (one complete assembled set at 22.0 g) Cycle times (typical): 7 s, 8 s, 9 s Electrical supply: 400 V, 50 Hz, 3PH+N+PE Main supply current: 191 A (auxiliary supply: 40 A) Short-circuit rating (panel): 10 kA Included peripherals: Plastic Systems resin dryer with material hopper, mold dehumidifier, and available spares Bottle formats supported via preforms: 0.2L, 0.5L, 1.0L Container material: PET Advanced Automation & Control Systems The machine features Husky engineering for precise temperature control, shot stability, and efficient thermal management across the 32-cavity hot runner. The molding system supports fast setup with plug-and-play cold half plates, simplifying changeovers between formats and weights. Operator interaction is streamlined through an integrated control interface for recipe management, alarm diagnostics, and process monitoring. The control panel is designed for industrial duty with a 10 kA short-circuit rating and clear segregation of main and auxiliary supplies. Integrated HMI for process control and monitoring Hot runner temperature control across all 32 cavities Quick-change cold half plates, tooling plate, and cooling pick set Electrical: 400 V, 50 Hz, three-phase with neutral and protective earth Production Line Integration Capabilities Optimized for PET preform manufacturing, this system integrates cleanly with upstream resin handling and downstream conveyance to stretch blow molding, quality inspection, and packing stations in beverage production. The included Plastic Systems resin dryer and mold dehumidifier stabilize material and mold conditions, enhancing repeatability and line throughput in broader bottling equipment ecosystems. Rodpfx Agoyhbd Se Isp Inline or standalone operation for preform supply Compatible with industrial packaging and beverage production lines Rapid format changes across 0.2L, 0.5L, and 1.0L bottle formats Designed for PET preforms used in water, juice, and other beverage applications Ma...

Condition: used, Year of construction: 2009, machine/vehicle number: PR22, Technical Specifications & Performance Data This Husky injection molding machine is engineered for high-efficiency cap and closure production, making it an excellent choice for beverage production environments that require consistent, high-quality outputs. Manufactured in 2009, the unit features a 160-ton clamp force platform paired with a 24-cavity cap mold optimized for 29/25 mm neck finishes. It is supplied with robust auxiliary equipment to stabilize process conditions and streamline operation in an industrial packaging workflow. Manufacturer: Husky Injection Molding Systems Model: H160 RS45/42 Year: 2009 Application: Cap/closure molding for beverage packaging Mold cavitation: 24 cavities Closure specification: 29/25 mm, Free Start Cap Nominal part weight: 1.20 g (cap) Clamp force: 160 tons Electrical supply: 400 V, 50 Hz, 3PH+N+PE Main supply current: 101 A Largest motor load: 42 A Largest heat load: 31 A Short-circuit current rating (SCCR): 10 kA Included equipment: Altanium heater controller, mold dehumidifier, hopper loader, color mixer unit, available spare parts Advanced Automation & Control Systems The machine is equipped with an Altanium heater controller to deliver precise thermal management across the hot runner zones. This tight temperature control promotes uniform melt flow, faster startups, and reduced scrap, vital for thin-wall cap molding. The industrial control panel supports a 3-phase + neutral + protective earth electrical system, with clearly defined load ratings for motors and heating circuits to facilitate safe integration and predictable operation. Precision heater control with Altanium technology Clearly rated electrical distribution for motors and heaters Stable process conditions for consistent cap quality Designed for quick setup and repeatable mold changeovers Production Line Integration Capabilities This unit integrates seamlessly into cap and closure production cells serving a used bottling line or standalone cap manufacturing operations. It can feed downstream systems such as vision inspection, lining/printing, and bulk handling for PET bottle closures. The 29/25 mm specification aligns with common beverage packaging neck finishes, supporting high-throughput operations in industrial packaging environments. Standalone or inline operation with downstream handling Compatible with PET bottle packaging for beverage production Auxiliaries included to stabilize material handling and color dosing Machine Condition & Maintenance History The machine is indicated as still in production, reflecting ongoing operational status and functional readiness. The inclusion of a comprehensive set of available spares and auxiliary units supports routine maintenance, uptime, and rapid troubleshooting typical of second hand industrial machinery maintained for continuous service. Rjdsyhbdxepfx Ag Iop Operational status: in production Auxiliaries and spares included for upkeep Operational ...

Condition: used, Year of construction: 2018, Overview  This complete brewhouse and cellar system was manufactured between 2018 and 2021 by several European equipment suppliers including Brewiks, Milan Svoboda, Mercabrewers, Wild Goose, Quantor and others. It features a 5 HL Brewiks brewhouse, a 12 HL fermentation cellar (6 CCTs), CIP stations, a canning line, labelling and coding units, water treatment, air treatment, chiller and full malt-handling equipment, being a turnkey solution for beer production. Technical data  Brewhouse (Brewiks 500, 2018) Capacity: 5 HL Heating: Electric, 36 kW Fermentation Cellar (Svoboda + Mercabrewers, 2018–2021) 6 CCTs × 12 HL useful capacity Pressure rating: 3 bar CIP Stations (Svoboda CIP 100) 2 mobile CIP units Tank capacity: 100 L (alkaline + acid) Canning Line (Wild Goose GOSLING, 2021) Semi-automatic Formats: 0.33 L / 0.44 L / 0.50 L Cooling (Quantor Chilly MAX 50L) Glycol chiller for CCTs General Key Information Power supply (various units): 230–400V, 50 Hz Applications: Brewing, fermentation, can filling Scope of Delivery  Brewiks Brewery (5 HL) | Brewiks | Brewiks 500 | 2018 | Electrically heated (36 kW) Isobaric CCT | Milan Svoboda | — | 2018 | 12 HL, 3 bar (1/3) Isobaric CCT | Milan Svoboda | — | 2018 | 12 HL, 3 bar (2/3) Isobaric CCT | Milan Svoboda | — | 2018 | 12 HL, 3 bar (3/3) Isobaric CCT | Mercabrewers | — | 2021 | 12 HL, 3 bar (1/3) Isobaric CCT | Mercabrewers | — | 2021 | 12 HL, 3 bar (2/3) Isobaric CCT | Mercabrewers | — | 2021 | 12 HL, 3 bar (3/3) CIP station | Milan Svoboda | CIP 100 | — | Mobile; 100 L alkaline + 100 L acid (1/2) CIP station | Milan Svoboda | CIP 100 | — | Mobile; 100 L alkaline + 100 L acid (2/2) Hop Cannon + Bag Filter | 3M | Series ME 01MET2 | — | 30 L capacity Glycol cooler | Quantor | Chilly MAX 50L | — | Operational, heavily used Canning line | Wild Goose | Quick Change GOSLING | 2021 | Semi-automatic; incl. formats 0.33 / 0.44 / 0.50 L Can Rinser + Gravity Feeder | Zomerdijk Engineering | TWIST Rinser | — | For 0.33 / 0.44 / 0.50 L Labeler + Printer | EME (Crafted Goose) | Jem-110-S2 | — | Automatic; integrated printer Thermal inkjet printer | Rynan | R20 (CM220) | — | Batch and date printing Air compressor | ABAC | 50 Hp2 | 2020 | 10 bar; 50 L tank Dehumidifier | ABAC | COOL21 (CO) | — | 16 bar; 350 L/min Reverse osmosis system | AquaControlada | — | — | 2 units (drinking & process water) Water tank | ROTH | — | — | 2× 750 L Malt mill | Sommer | Maltman 220 | — | Precision mill Sieve shakers + sieves | RETSCH | AS200 Basic | — | Complete sieve set for malt analysis Rjdpfx Asyb R Iaog Iep

Condition: good (used), Large-scale system for climate tests with S!MCON control Design The system consists of the following main components: - Walk-in, insulated test room - Air treatment room - Machine unit - Air conditioning system - Control cabinet Test room The fixtures in the test room are made of corrosion-resistant material. The test room can be illuminated, is walk-in, and has a condensate and cleaning drain. Air treatment room The air treatment room is located behind the air baffle in the insulated interior. It contains the following components necessary for temperature control and is accessible via easily removable panels. - Test room fans - Heat exchangers - Electric heaters - Ventilation and exhaust system - Temperature sensors In the air treatment room, the air is tempered (cooled/heated), humidified and dehumidified, and circulated by fans. The air is drawn in under the ceiling and expelled at floor level. Rodpfx Ajw U Sv Esg Iep Sensors The temperature and humidity sensors are located behind the air baffle in the air treatment room. Machine Unit The machine unit, consisting of refrigeration units, supplies the air treatment room with the required energy. Climate System The climate system consists of: - Steam humidifier - Dehumidification evaporator Technical Data Test chamber volume: approx. 32 m³ Direct temperature range: -40 to +100°C Temperature fluctuation over time in the center of the usable space: +/- 0.5 to +/- 1 Temperature change rate Heating: from -35°C to +50°C at 3 K/min Cooling: from +85°C to +85°C at 2 K/min from +80°C to -40°C at 1 K/min Data for climate testing Temperature range: 10 to 95°C Humidity range: 10 to 95% RH Dew point range: 5 to 93°C Temperature fluctuation: +/- 5°C Humidity fluctuation: +/- 3 to +/- 5% RH Cooling water specifications Connections Inlet: 2 x 1 1/2" RH Return: 2 x 1 1/2" RH Consumption at full load: max. 16 m³/h Maximum load on the test chamber floor: 10,000 N/m² Nominal voltage: 3/N / PE AC 400 V 50 Hz Nominal power: 97 kW Nominal current: 148 A Dimensions: Test chamber: Width 3.60 m, Height 2.20 m, Depth 5 m Climate chamber divided for transport at a specified location (approx. 2.50 m). Financing through our bank is also possible. komplett-konzept.leasingo.de Find more items – new and used – in our shop! International shipping costs on request!

Condition: new, Year of construction: 2026, total length: 1,010 mm, total width: 1,010 mm, total height: 2,010 mm, mesh size: 10 mm, We manufacture in Ukraine a heavy-duty stainless steel drying trolley, specifically designed for industrial and semi-industrial production of meat and fish snacks, raw-cured sausages, jerky, and pet treats. The trolley is fully compatible with our RK50U, SAS200, and FARS200 systems, and is ideal for use in drying chambers, smokehouses, and climate-controlled environments equipped with air dehumidifiers. Rjdpfx Aerftxfsg Iop The external dimensions of the trolley are 2000 × 1010 × 1010 mm. The frame is constructed from corrosion-resistant AISI 304 stainless steel, using a robust 40 × 40 × 1.5 mm profile. It features 30 levels with a 55 mm gap between each tier and is equipped with special locking mechanisms to prevent trays from falling during movement or operation. For easy maneuvering, the trolley includes six heavy-duty pendulum swivel casters (Ø125 mm), enabling rotation on the spot, even when fully loaded. Each trolley comes with 60 stainless steel trays, each measuring 900 × 500 mm. The trays are made from corrugated stainless steel wire mesh, available in 12×12 mm or 10×10 mm configurations. The wire thickness is 0.95 mm, ensuring excellent structural rigidity. Each tray includes a 15 mm high perimeter rim to promote optimal airflow and heat convection. A reusable, non-stick Teflon insert is included with each tray—perfect for sticky or soft products such as minced meat sticks, fish strips, or salami-style snacks. The total load per trolley is approximately 600 kg, with up to 10 kg of evenly distributed product per tray. The design supports both high- and low-temperature drying, and the trolley fits seamlessly into chambers with either horizontal or vertical airflow. It is optimized for easy cleaning and maintenance. This trolley is engineered for efficient moisture removal and uniform air distribution across all product levels—ensuring optimal drying performance and extended shelf life. Pricing & Availability • New set with 10×10 mm mesh and Teflon inserts: €3,500 (in stock in Vilnius, Lithuania EU) • Used set with 5×5 mm mesh, no Teflon: €2,300 (excellent condition, 7 units available) We deliver across the EU (Poland, Lithuania), UK, Ukraine, Australia and internationally. For technical drawings, a custom offer, or export documentation, feel free to contact us.

Year of construction: 2015, condition: excellent (used), Moretto XD20 (2015) 4,7 KW/6,3HP Rjdsx E Ur Espfx Ag Isp Dehumidifier XD20 Dryer OTX60VP

Condition: good (used), Year of construction: 2017, machine/vehicle number: API262376, overall weight: 279 kg, volume flow: 150.6 m³/h, pressure (max.): 12.75 bar, Equipment: refrigerant dryer, type plate available, We offer: ATLAS COPCO GA15VSDFF PLUS Technical data: YEAR: 2017 CAPACITY (kW): 15 Rsdpev Drrbefx Ag Isp OUTPUT (m3/min): 2.51 CIS (bar): 12.75 HOURS (DOC/GENERAL): 25107 INVERTER: yes BUILT-IN DEHUMIDIFIER: yes

Condition: excellent (used), Year of construction: 2022, only 470 hours Maschine hat einen 60° Schneidkopf und ist somit mit 5-Achsen The Intermac Primus 184 is a high-performance, compact 3 or 5-axis waterjet cutting machine designed for precision cutting of materials like stone, glass, and metal. It features a plug-and-play design, integrated abrasive removal, and user-friendly CAD/CAM software. The machine handles, for example, 1860x4000mm sheet sizes up to 200mm thick. Key Features and Specifications: Capacity: Working area of roughly 1860 x 4000 mm (depending on configuration) with 5-axis capability. Technology: Uses high-pressure water (via BFT Hytron 0.37, 37KW intensifiers) with abrasive for combined erosion and abrasion cutting. Compact Design: The electrical cabinet is integrated into the console, and the abrasive removal system is built into the structure. Versatility: Suitable for intricate, complex shaping with high precision and optimal finish, often used in stone (countertops) and glass fabrication. Software: Includes intuitive, touch-screen compatible CAD/CAM software for easy, assisted design. Speed: Offers rapid setup times and advanced, automated nesting features to maximize productivity. The Primus 184 is considered an ideal, versatile solution for both small-batch and large-scale production, featuring robust construction and advanced safety, including, in some models, fully enclosed work areas. Machine Benefits Technical Machine Benefits Working area 1860 x 4000 mm Pressure booster bft hytron 0. 37 (37kw delivery volume 3,8l / min) Technical data of the INTERMAC PRIMUS 184 waterjet cutting machine - processed materials: monolithic glass, laminated glass, multi-layer glass, fire-resistant glass, reinforced glass, acrylic glass (plexiglass) - number of axles : 5 Redpsyinaasfx Ag Isp - feed in the X/Y/Z axis: 1860/4000/250 mm - Worktable surface (L x W): 4000 x 1860 mm - Maximum workpiece thickness: 250 mm - maximum dimensions of the workpiece (L x W): 4200 x 2010 mm - pump power: 37 kW - maximum pump pressure: 400 MPa - Maximum pump flow: 3.8 l/min - power supply: 3x 400 V; 50 Hz - Dimensions (L x W x H): 5690 x 2420 x 2050 mm - weight of the INTERMAC PRIMUS 184 machine: 3800 kg Equipment of the INTERMAC water cutter - control system - CAD/CAM software - high-pressure pump: BFT ECOTRON 40.37 (2021) - Z-axis with a sensor that allows automatic management of the distance between the cutting head and the material surface - a system that optimizes the flow of abrasive depending on the type of material, thickness of the material and the type of work performed - Finished Element Cleaning System - system monitoring the water level in the tank - light curtains - dehumidifier - air oil separator - Positioning laser - Cutting head guard - electrical cabinet with air conditioning Pump workhours aprox 470h

Condition: new, Year of construction: 2026, The most powerful centrifugal fan FAN5500 reaches a capacity of up to 8000m3/h. The high vacuum created by the blade system at the right angle and the high motor power can cope with the toughest jobs.Thanks to the many years of experience of our CORMAK team, radial fans from the FAN series have been created. The design of a new technological line allowed us to create the LineWind metal turbine system. This is the most important feature of the centrifugal fans, enabling them to extract all kinds of pollutants with increased vacuum power thanks to a special blade system that has been profiled at the right angle. The centrifugal fan was developed for use in the carpentry, furniture, automotive, agricultural and manufacturing industries. Radial fans are used for: transport of shavings, sawdust, small granulates dusty air local exhaust ventilation drying systems dehumidifiers Multi-vane metal rotor! High efficiency ensured by a balanced impeller Thermal winding protection (thermal sensor). The extraction design has been enhanced with additional anti-vibration feet in the base to guarantee a stable and vibration-free operation of the unit. An emergency shutdown button meets the requirements of the PN-EN ISO 12100 and PN-EN ISO 13850 standards. An additional advantage is the use of branded flexible and resistant seals in sensitive areas, allowing high vacuums to be achieved without losses at individual connection points. Reliability confirmed by Polish users who enjoy working with our machines every day. Technical specifications MAX. AIR CAPACITY 8000 m3/h inlet diameter 300 mm discharge diameter 250 mm ENGINE SPEED 2850 rpm Rodsvughlopfx Ag Iop DIMENSIONS 670 x 600 x 600 mm MOTOR POWER / VOLTAGE 5.5 kW/400 V WEIGHT 55 kg

Condition: new, Year of construction: 2026, The centrifugal fan allows for operation with increased vacuum power to extract various types of pollutants, thanks to a special blade system which has been profiled at an appropriate angle. The radial fan has been developed for use in the carpentry, furniture, automotive, agricultural and manufacturing industries. Thanks to the many years of experience of our CORMAK team, radial fans of the FAN series were created. Designing a new technological line allowed us to create the LineWind metal turbine system. This is the most important feature of the centrifugal fans, enabling them to extract all kinds of pollutants with increased vacuum power thanks to a special blade system that has been profiled at the right angle. The centrifugal fan was developed for use in the carpentry, furniture, automotive, agricultural and manufacturing industries. Rjdjvugg Uepfx Ag Ijp Radial fans are used for: transport of shavings, sawdust, small granulates dusty air local exhaust ventilation drying systems dehumidifiers Multi-vane metal rotor! High efficiency ensured by a balanced impeller Thermal winding protection (thermal sensor). The extraction design has been enhanced with additional anti-vibration feet in the base to guarantee a stable and vibration-free operation of the unit. An emergency shutdown button meets the requirements of the PN-EN ISO 12100 and PN-EN ISO 13850 standards. An additional advantage is the use of branded flexible and resistant seals in sensitive areas, allowing high vacuums to be achieved without losses at individual connection points. Reliability confirmed by Polish users who enjoy working with our machines every day. Technical specifications MAX. AIR CAPACITY 4000 m3/h inlet diameter 200 mm discharge diameter 180 mm ENGINE SPEED 2850 rpm DIMENSIONS 575 x 550 x 500 mm MOTOR POWER / VOLTAGE 2,2 kW / 400 V WEIGHT 35,5 kg