Used Disc Sanding Machine for sale (69,581)

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Lodot Tqy Eopfx Ab Terh Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-180 mm HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----- Manufacturer's description: ----- Compact design designed according to modern principles. Quiet and vibration-free operation thanks to rigid, stable machine housing and special insulation. Work safety device in accordance with the EC Machinery Directive with the "dust-tested" certificate. Offset grinding units with large-dimensioned tension rollers for good heat dissipation and stable sanding belt guidance. Sanding units with forced sanding belt oscillation. 2-point sanding dust extraction directly on the sanding roller. Airborne dust extraction on the large tension rollers. Integrated sanding belt blower for longer service life of the sanding belts. Integrated brushing and finishing device, adjustable via threaded spindle, with large dust extraction. Motorized grinding thickness adjustment of the entire upper unit via precision threaded spindles and linear ball sets on hardened and ground precision shafts with dust and dirt protection. Electronic digital display for workpiece thickness (resolution 0.1 mm). Contact roller and grinding shoe in a balanced ratio to the grinding belt grain load. Hardened and ground grinding rollers. Maintenance-free and wear-free oxide ceramic grinding shoes (DBGM) with excellent sliding properties, good heat dissipation and high dimensional accuracy. Grinding belt tension via pneumatic cylinder. Grinding belt change via pneumatically controlled belt relaxation. Ability to adjust the grinding belt run when changing the belt. Electro-pneumatic pressure monitoring of the compressed air supply with visual fault display. Automatic machine stop triggered when sanding belt breaks and by run-in protection with integrated wood thickness control. Optical display on the control panel. Feed device and proven, calibrated non-slip and non-adhesive transport belts on precisely ground tables and spring-loaded pressure rollers. Cardan shaft drive for even wood transport. Feed speed continuously adjustable. Chip removal adjustment bottom via precision threaded spindle with dimension display via scale ring (resolution 0.1 mm) Ergonomic arrangement of the operating and setting elements on the machine front: sanding unit and brush device at the top, sanding unit and brush device at the bottom, workpiece transport device, sanding thickness setting, operating display, fault display. Control and operating unit with lockable main switch built into the machine housing. All motors electrically protected against overload. Technical data: ----- Grinding belt speed: 24 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 180 mm Shortest workpiece length: 300 mm Feed speed: Continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm wide 1600 mm long Electrical connection: 400 V, 3/N PE, 50 HZ Grinding units: 2 x 4 kW Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection: R 3/8", 80 NL, 8 bar Extraction air volume: 2 x 2000 - 2500 m3/h 20 - 25 m/sec. Extraction connection nozzle: 2 x 160 mm diameter at the top of the machine Ljdpfx Abov D Rg Ds Torh housing External dimensions: Length: 1600 mm Width: 1030 mm Height: 1820 mm Height with extraction nozzle: 1930 mm Working...

Condition: ready for operation (used), Year of construction: 2008, Table size: 220 x 820 mm Table size (front table): 250 x 350 mm Ledpfxjv Efn Sj Ab Terh Grinding wheel dimensions: 150 x 2260 mm Grinding belt speed: 16 m/s Drive motor: 400 V, 1.5 kW Weight: 164 kg Space required: 1200 x 600 x 1250 mm

Year of construction: 1987, condition: good (used), machine/vehicle number: 17/4, usable grinding wheel outer Ø: 600 mm Table size: 470 x 950 mm Table can be tilted down/up to: 45/30° Table height above floor: 950 mm Grinding wheel speed: 940 rpm Grinding wheel drive: 380 V, 940/1140 rpm, 2.2/2.5 kW Lredpfx Abeit N Ipe Tsh Weight: 237 kg

Condition: defective spare-parts repository (used), Surface grinding unit on the left, roller diameter: 100 mm Grinding belt length: 950 x 100 mm Horizontal/vertical table support: 120 x 180/10 x 250 mm Contact grinding wheel on the right, 200 mm diameter, grinding belt dimensions: 50 x 2000 mm Lrodpfjwvt I Hsx Ab Tsh 2 spindle speeds thanks to pole-changing motor: 11450/2900 rpm Drive motor: 380 V, 0.9/1.3 kW Space required: 1000 x 400 x 1800 mm Weight: 140 kg

Condition: good (used), Year of construction: 2006, Belt sander 75 with pedestal Ledpfxoxyqi To Ab Tjrh

Year of construction: 1991, condition: used, Used machine Year of manufacture: 1991 With 4 sanding units Workpiece dimensions: Thickness min. 10 mm max. 150 mm Width min. 10 mm max. 180 mm Length min. 190 mm, max. unlimited Abrasive belt dimensions: 200 x 1800 mm Extraction ports 2 extraction ports 80 mm 4 extraction ports 120 mm Lodpfxow Tfxdj Ab Terh Required air velocity: 30 m/sec L x W x H: 3400 x 1150 x 1805 mm Weight: 2400 kg Availability: short term Location: Odenwald

Condition: new, Year of construction: 2025, New machine Year of manufacture 2025 Edge sanding machine with integrated dual conveyor feed system for solid wood parts, veneered edges, and curves, featuring oscillation of the entire sanding unit. Processing of solid and veneered edges either manually or with automatic feeding: - On the veneer sanding side, along the two stop plates (with infeed stop including integrated extraction slots and fine adjustment according to removal scale) onto the elastic sanding pad (oscillating for uniform use of the graphite lining, including grit compensation adjustment and belt tension relief via two deflection rollers), with infeed stop extension, table size 1180 x 325 mm. Lrsdpfx Asw Tfx Dob Tjh Manual processing of straight and curved solid wood parts: - On the solid wood sanding side against the continuous, glide-backed sanding belt support, table size 1180 x 325 mm including miter fence with scale. - On the front side with an optionally quick-mountable semicircular table (with dust extraction holes) against the rubberized belt drive roller Ø 90 mm, support radius 300 mm. - On the drive roller, optionally with a quickly mountable auxiliary cast iron table (with dust extraction holes) 400 x 500 mm on an oscillating spindle for use of sanding drums Ø 25, 30, 40 and 45 x 100 mm for external and internal curves, with spindle safety cover. Design: Robust machine frame with heavy cast iron tables, sanding unit motorized height adjustment up to 120 mm and tiltable up to 45° without any table adjustments (patented construction), belt drive motor 3 kW (4 HP), 400 V/50 Hz, with motor protection switch, separate motor for belt oscillation, oscillation stroke programmable from 10 - 90 mm, control box integrated in frame, constant belt tension with length compensation, belt tracking adjustable, safety guard, dust extraction via two extraction hoods, flexible hoses and common internal pipe to 150 mm connection, recess in frame for easy transport with pallet or forklift, belt width 150 - 200 mm, belt length 2000 mm, working height 830 mm (solid sanding table) or 900 mm (veneer sanding table), net weight 750 kg, footprint 1150 x 800 mm. Feed system: Integrated in the frame, two parallel transport belts 50 mm wide, spaced 250 mm apart on the underside, 20 mm wide top pressure rollers, 0.55 kW (0.75 HP) motor, continuously adjustable speed 3 - 15 m/min. COMFORT version Kündig UNIQ-S Including table extension UNIQ/UNIQ-S/Flash Including upper extraction duct UNIQ without slide Including semicircular table for belt drive roller UNIQ-S Availability: short-term Location: Flörsheim

Condition: new, Year of construction: 2022, New machine Year of manufacture 2022 THE ADVANTAGES 4 workstations on one machine 80, 300 and 1000 mm radii Straight and curved grinding back 150 mm belt height Pneumatic belt tensioning Stepless pneumatic aggregate oscillation Lsdpfx Abjkwhwle Terh Solid cast iron aggregate long lasting good sanding results Suction all around the worktable Only the highest quality components Because we are convinced of ourselves 5 years warranty Every machine handmade in our home country (Rehnen) Lifetime spare parts supply GS & BG dust tested Motor power: 4 KW Sanding belt size: 150 x 2700 mm Sanding belt speed: 15m /sec. table size: 345 x 2000 mm space requirement: 2000 x 3000 mm weight : 560 kg Suction diameter : 140 mm Availability : short term Storage location: Hochheim

Condition: new, Year of construction: 2022, Exhibition machine Year of manufacture: 12/2022 Features and technical data: DESCRIPTION • Grinding unit tiltable by hand crank • The machine frame made of welded steel ensures high torsional rigidity and vibration-free operation • Oscillating sanding belt with a separate geared motor for improved sanding results • Oscillation can be switched on or off as needed • Sanding platen with graphite coating for longer belt life • Height-adjustable sanding table to utilize the entire belt width • Auxiliary table for sanding radii with integrated extraction ports • Sleeve sanding device with attachable work table • Spring-loaded belt tension automatically compensates for belt length differences • Equipped with adjustable stops, ideal for veneer sanding • Veneer overhang can be sanded off effortlessly TECHNICAL DATA Dimensions and weights Product length approx. 1700 mm Product width/depth approx. 1000 mm Product height approx. 1150 mm Net weight approx. 300 kg Drive power Oscillation motor power: 0.11 kW Extraction connection Extraction port diameter: 2 x 100 mm Work tables Table length: 950 mm Lrjdpow I Uvzjfx Ab Tjh Table width: 450 mm Table height adjustment: 110 mm Electrical data Connection voltage: 400 V Mains frequency: 50 Hz Grinding unit Sanding belt length: 2640 mm Sanding belt width: 150 mm Belt speed: 14 m/s Oscillation stroke: 15 mm Sanding area length: 800 mm Sanding area width: 150 mm Tilt range of grinding unit: 0–45° SCOPE OF DELIVERY • 1x sanding belt K100 • 5x rubber rollers Ø25, Ø30, Ø40, Ø45, Ø50 mm • 6x sanding sleeves K80 – Ø25, Ø30, Ø35, Ø40, Ø45, Ø50 mm • Standard tool kit • Mitre gauge Location: Hochheim Availability: Immediately

Condition: excellent (used), Year of construction: 2004, grinding height: 100 mm, working width: 250 mm, grinding width: 250 mm, Double-sided brush sanding machine / profile sanding machine Manufacturer: Quickwood Model: QL 3 Year of manufacture: 2004 Texturing and sanding machine, double-sided operation, equipped with a total of 6 brush units. Machine suitable for integration into production lines due to constant table height. Working width: 250 mm Passage width: 300 mm Passage height: approx. 100 mm Minimum workpiece length: approx. 500 mm Equipped with: 2x brush units from below, each 1.5 kW, frequency controlled, suitable for texturing and sanding 2x brush units from below, each 1.5 kW, frequency controlled, suitable for texturing and sanding 2x brush units from above, each 0.75 kW, frequency controlled, suitable for fine sanding Pneumatically controlled pressure rollers for workpiece guidance and stabilization Lodpfexvz Ulsx Ab Terh Feed rate steplessly adjustable, approx. 5 - 25 m/min Extraction connections: 150 mm Dimensions approx. 2045 x 1350 x 1700 mm (LxWxH) Weight: approx. 1000 kg

Condition: new, High quality belt sander with top equipment. FLEET BSM 75 (374000) Standard equipment - High quality construction - Drive roller is crowned (this automatically centers the sanding belt on the roller) - Fully vulcanized contact roller for longest service life and best running smoothness - Tool-free and thus fast, uncomplicated change of the sanding belt - Infinitely variable height adjustment for optimum set-up of the belt sander to suit the user - Freely adjustable metal fence for optimum and safe guidance of workpieces when use of the large surface grinding area - Belt speed optimized by design so that burning of the workpiece during processing can be excluded as far as possible - Models with suction equipped with robust and flexible suction hoses - motor protection switch with CEE collar plug incl. phase inverter - motor brake (except BSM 75 A pol) - incl. sanding belt grit 60 - Dust bag (only with suction) - 5 years warranty on drive motor for single shift operation Technical data belt length (mm): 2.000 belt width (mm): 75 surface grinding range (mm): 600 Color (RAL): 9007 Dimension machine without VP (mm): 1.100 x 550 x 1.035 Lrjdpskyt Apsfx Ab Toh dimension machine with VP (mm): 800 x 600 x 1.450 Belt speed (m/s): 30 motor rotary current 400 V (kW): 3,75 Suction capacity (m3/h): - Suction motor (kW): - Weight (kg): 80 Note: For all other models, please contact us.

Condition: new, High quality belt sander with top equipment. FLOT BSM 150 (374020) Standard equipment: - High quality construction - Drive roller is crowned (this automatically centers the sanding belt on the roller) - Fully vulcanized contact roller for longest service life and best running smoothness - Tool-free and thus fast, uncomplicated change of the sanding belt - Infinitely variable height adjustment for optimum set-up of the belt sander to suit the user - Freely adjustable metal fence for optimum and safe guidance of workpieces when use of the large surface grinding area - Belt speed optimized by design so that burning of the workpiece during processing can be excluded as far as possible - Models with suction equipped with robust and flexible suction hoses - motor protection switch with CEE collar plug incl. phase inverter - motor brake (except BSM 150 A pol) - incl. sanding belt grit 60 - Dust bag (only with suction) Lodpskytfhjfx Ab Tjrh - 5 years warranty on drive motor for single shift operation Technical data: Belt length (mm): 2,000 belt width (mm): 150 surface grinding range (mm): 600 Color (RAL): 9007 dimension machine without VP (mm): 1.100 x 550 x 1.035 dimension machine with VP (mm): 800 x 600 x 1.450 Belt speed (m/s): 30 motor rotary current 400 V (kW): 3,75 Suction capacity (m3/h): - Suction motor (kW): - Weight (kg): 90 Note: For all other models, please contact us.

Condition: good (used), Prism length: 450 mm Travel distance: 290 mm Chamfer height: 0 - 3 mm x 45° Minimum workpiece thickness: 2 mm Maximum workpiece weight: 30 kg Tool holder: ø 6 + ø 8 mm Stepless spindle speed: 6 000 - 23 000 rpm Asynchronous motor: 230 VAC / 250 W Dimensions W x D x H: approx. 500 x 250 x 200 mm Ledpfx Asrypbyeb Tsrh Weight: approx. 20 kg

Condition: used, Year of construction: 1991, functionality: fully functional, total width: 2,000 mm, total height: 2,150 mm, total length: 2,450 mm, overall weight: 4,200 kg, power: 25 kW (33.99 HP), input voltage: 380 V, control type: manual, degree of automation: manual, actuation type: electric, Number of sanding units: 4 pcs Sanding width: 190 mm Lsdm U H Nfet Tqy Eofjrw Max. sanding height: 4–180 mm Weight: 4200 kg Hess Expert 4-Belt Single Wood Sanding Machine Ø Sanding from below/above Ø With 2 offset sanding units each (below and above) Ø Sanding units (below and above) arranged in series according to the planing principle Ø Pre-sanding with coarse grit (calibration) Ø Fine sanding with fine grit (finishing) Ø Central motorized height adjustment of the lower sanding units Ø Central motorized and synchronous height adjustment of the complete upper sanding and brushing units, including the upper feed units Ø Oscillating use of sanding belts (during the sanding process) Ø Absolute power connection via 5.5 kW motors and large-dimensioned drive drums Ø Oxide-ceramic sanding shoe for: - precise surface geometry - no need for readjustment - permanent dimensional accuracy - completely maintenance- and wear-free Basic structure: Stable, heavy-duty welded construction made of thick-walled rectangular profiles with additional, statically calculated reinforcements for optimal vibration damping. Offset sanding units with large-scale belt drive drums for slip-free belt tracking. Dual-point extraction for direct and airborne dust, with sealing brushes and integrated sanding belt air-blast system to extend sanding belt service life. Sanding units made from heavy steel plate design as a basis for vibration-damped, smooth belt running. Absolutely backlash-free guides using ball linear sets made from hardened and ground shafts. Height adjustment of sanding units via hardened and ground special linear guides and preloaded guide carriages. Lasting precision due to dust and dirt protection of the ball linear sets and guide carriages. Large-diameter pre-sanding rollers serve as contact rollers. Contact rollers and sanding shoes are optimally matched to the sanding belt grit load. The large-dimensioned drive drums guarantee full transmission of the sanding motors’ 5.5 kW output to the sanding belt, ensuring slip-free, stable running and optimal heat dissipation. This enables maximum stock removal. Automatic machine stop trigger in the event of belt breakage. Optical indicator at the control panel and machine warning beacon. Finishing sanding shoes are completely maintenance- and wear-free, made from oxide-ceramic for optimal heat dissipation. Ljdpfxsxzbdko Ab Terh Sanding belt tension by appropriately dimensioned pressure springs. Sanding belt release for belt changes using a pneumatic system for sensitive, distortion-free installation of new belts. Upper sanding unit and brushing device are centrally motorized, height-adjustable with digital display at the control panel for motorized sanding thickness adjustment. Integrated brushing and finishing device for improved surface finish, built into the main machine. Two vertically-aligned special brush rollers, 150 mm diameter, operating in the same direction as the feed. Separate height adjustment of the brush rollers using precise slide guides for wear compensation. Additional conveyor roller for removing or further transporting the workpiece out of the sanding machine, coupled with the transport belt. The Feeding mats have been recently changed

Condition: new, Special offer price for stock goods! Only while stocks last! Price ex stock, plus VAT. Belt sander: Bernardo type/model: MS 75 x 2000 S Condition: new belt dimensions: 75 x 2000 mm belt speed: 29 m/sec. contact wheel Ø x W: 200 / 80 mm surface grinding table: 460 x 75 mm suction connection: 100 mm motor output power S1 100%: 3,0 kW motor input power S6 40%: 4,0 kW Voltage: 400 V Lredpfx Abofnr Ais Tsh length: 1080 mm width: 440 mm height: 1000 mm Weight approx.: 66 kg Features: Good grinding performance due to high belt speed Quick adjustment for horizontal and inclined position Continuous plane grinding surface for optimum grinding of long workpieces Constant belt tension due to spring-loaded tensioning device Universally applicable for sanding edges, surfaces and for cylindrical sanding Including quick tensioning system for fast belt change Easy adjustment of parallel belt run by means of adjusting screw Graphite coating on the face grinding surface increases the sliding properties of the grinding belt Scope of delivery: - Sanding belt K 80 - Hinged protective disc - Grinding and support table - Workpiece stop - Dust extraction nozzle - Separate off button - Base frame

Condition: new, Deburring machine brand: Aboagye Model: AF 165 Condition: new machine Speed: 2,800 RPM maximum cutting width: 1 mm equipped as standard with: Lsdpfx Abodurxne Torh -Special flap disc K80-ST -Suction nozzle -Manual

Condition: new, Year of construction: 2025, Bandwidth: 200mm Belt length: 3000mm Table size: 960mm x 352mm Additional table: 330mm x 330mm veneer sanding device: yes oscillation: yes sanding unit swiveling: yes suction connection: 120mm Lrjdpfohy Iyvsx Ab Teh Motor power: 3 kW Machine length: 1900mm Machine width: 900mm Weight: 310kg

Condition: used, Year of construction: 2002, Used machine Year of manufacture 2002 Edge sander with electromechanical oscillation with a 15 mm pendulum stroke of the motorized disc Lsdpjw I U Ahjfx Ab Terh Swivel of the sanding unit by 90° using a hand crank (continuous angle adjustment; read off the scale) Additional table with extraction system for using sanding rolls Height-adjustable table for utilizing the sanding belt Motor 2.2 kW Oscillation motor 0.11 kW Table size 880 x 370 mm Belt dimensions 150 x 2580 mm Dimensions 1700 x 1000 x 1150 mm Weight 250 kg Availability: Short-term Storage location: Flörsheim

Condition: new, Year of construction: 2022, Belt width: 150mm Belt length: 2600mm Oscillation: yes Lrsdpfx Asiuld Dob Tsh Sanding rollers for curves: 1 Sanding unit can be swivelled: yes Table size: 750mm x 290mm Suction connection: 120mm Motor power: 3kW Machine length: 1700mm Machine width: 700mm weight: 180kg

Condition: new, Year of construction: 2022, Strip width: 150mm Belt length: 2740mm veneer sanding device: no oscillation: yes roller diameter: 115 mm Grinding unit swivels: yes / 90° - 0° worktable: 900 x 305 mm additional table: 290 x 260 mm Belt speed : 16 m/sec. m/sec. Suction connection : 100mm Motor power : 3 kW / 400V Machine length: 1540 mm Machine width: 750 mm Weight: 220 kg Lodpehq A H Djfx Ab Tjrh

Condition: new, Year of construction: 2022, Belt width: 150mm Strap length: 2260mm Ledpfeha Nz Rox Ab Tsrh Veneer sanding device: no Oscillation: yes Roller diameter: 115 mm Sanding unit swivels: yes / 90° - 0° Work table: 750 x 250 mm Additional table: 300 x 245 mm Belt speed: 16.3 m/sec. Suction connection: 100mm Motor power: 3 kW / 400V Machine length: 1270mm Machine width: 600mm weight: 120kg

Condition: new, Year of construction: 2022, Bandwidth: 150mm Belt length: 3000mm Table size: 960mm x 352mm Additional table: 330mm x 330mm grinding roll diameter: 60mm / 100mm / 120mm Lodegtdpuspfx Ab Tjrh veneer sanding device: yes Oscillation: yes sanding unit swivels: yes suction connection: 120mm Motor power: 3 kW Machine length: 1900mm Machine width: 900mm Weight: 310kg

Condition: as good as new (ex-display), Year of construction: 2022, Strip width: 150mm Belt length: 2400mm veneer sanding device: no oscillation: yes roller diameter: mm grinding unit swiveling: yes / 90° - 0° Work table: 730 x 300 mm additional table: 420 x 400 mm Belt speed : 14 m/sec. m/sec. Suction connection : 120mm Motor power : 1,8 kW / 400V Machine length: 1480 mm Machine width: 680 mm Ledjhpmadopfx Ab Terh Weight: 160 kg

Condition: as good as new (ex-display), Year of construction: 2022, Strip width: 150mm Belt length: 2170mm Table size: 1440mm x 710mm veneer sanding device: yes oscillation: yes Table tilting: yes, 0°÷ 45° Suction connection: 120mm Motor power: 3 kW Machine length: 1440mm Machine width: 800mm Weight: 530kg Ledpfx Abehpmahs Terh