Used Dna Sequencer for sale (522)

Condition: used, Illumina DNA Sequencer MiSeq SY-410-1003 Description: RFID tracking for consumables MiSeq Control Software 2.6 LTSC Hfsdpfozikcrsx An Nen Operating environment Temperature: 22 °C ± 3 °C Humidity: Non-condensing, 20 % – 80 % Altitude: Less than 2,000 m (6,500 ft) Air quality: Pollution degree II Ventilation: Maximum 1,364 BTU/h For indoor use only Light-emitting diode (LED) 520 nm, 660 nm Dimensions W × D × H: 68.6 cm × 56.5 cm × 52.3 cm (27.0 in × 22.2 in × 20.6 in) Weight: 57.2 kg (126 lb) Power supply 90–264 VAC at 50/60 Hz, 10 A, 400 W Radio frequency identification (RFID) Frequency: 13.56 MHz Power: 100 mW Product safety and compliance NRTL certified IEC 61010-1 CE marked FCC/IC approved Important note: “The table shown in the photos is not included in the sale.” Condition: used Scope of delivery: (See pictures) Weight: approx. 35 kg (Subject to changes and errors in the technical data and specifications!) We will be happy to answer any further questions you may have by phone.

Year of construction: 2015, condition: excellent (used), Exceptional Opportunity! From the former collection of the Max Planck Institute in Freiburg, we can offer you this highly efficient gene sequencing system, model "NextSeq 500," from the world-renowned brand "illumina." This system is one of the most powerful and widely used fully automatic gene sequencing systems, and it has become indispensable in virtually every laboratory worldwide. It is primarily used as a high-throughput system for the automated generation of DNA clone clusters through sequencing and primary analysis. Thanks to its particularly compact design, it is also perfectly suited for smaller laboratories and can be used ideally as a stand-alone device – all the necessary components are already integrated into the device, and complete operation can be performed via the built-in screen and a wireless keyboard. The device was acquired by the Max Planck Institute in 2016 and has been used very little. It has been continuously serviced by the manufacturer's customer service department and has only completed 395 runs – it is therefore in flawless condition both visually and technically – see the pictures. The device can be used immediately; however, for the sake of good order, we would like to point out that in a commercial operation, the legally required tests according to MTK/STK must be carried out again. Dimensions (H x W x D): approx. 585 x 534 x 635 mm Weight: approx. 85 kg Hjdpfoz Rph Iex An Nofn The total weight of the system, including accessories and pallet, is approximately 110 kg! The device can be picked up from our premises during regular opening hours after prior telephone arrangement. For an additional charge, shipping can be arranged within three working days after payment receipt, insured via a shipping company. The sale is exclusively to commercial businesses; you will, of course, receive an invoice with VAT shown. Private buyers have the option of purchasing the device "on behalf of a customer"; a direct commercial sale to private individuals is expressly not permitted! The goods are sold excluding any warranty or liability for defects. The exclusion does not apply to claims for damages arising from gross negligence or intentional breach of the seller's obligations, as well as for any injury to life, body, and health. If you have any questions regarding prices or technical details, please do not hesitate to contact us at the address provided.

Year of construction: 2024, condition: like new (used), Perkin Elmer Chemagic 360-D Nucleic Acid Extraction System The Perkin Elmer Chemagic 360-D is an automated benchtop system for the isolation of nucleic acids (DNA and RNA) from a variety of sample materials. It utilizes Chemagen’s magnetic bead technology to obtain highly pure nucleic acids for various downstream applications. Key Features and Specifications Technology: The system is based on Chemagen’s patented M-PVA magnetic bead technology. Metal rods are magnetized to collect the beads with the bound nucleic acids and transfer them between different process solutions, thereby minimizing cross-contamination. Sample Volume Flexibility: It offers various "Rod Heads" (magnetic rod heads) for different volume ranges and throughputs: 12-Rod Head: For sample volumes from 1 ml to 10 ml. 24-Rod Head: For sample volumes from 200 µl to 4 ml. 96-Rod Head: For sample volumes from 10 µl to 400 µl. Applications: The isolated nucleic acids are suitable for a variety of applications, including Next-Generation Sequencing (NGS), genotyping, PCR, and MLPA. Software: The intuitive Chemagic software allows for easy setup of protocols, tracking of process status (run time, remaining time), and generation of LIMS-compatible log files for quality assurance. Accessories: An optional Chemagic Dispenser 360 is available to quickly and accurately pre-fill reagents, reducing manual working time. Dimensions: The device measures 800 x 800 x 900 mm (W/D/H). Certification: The 360-D version is a CE-IVD-registered and FDA-listed instrument intended for in-vitro diagnostics (in combination with the appropriate kits). The Advantages at a Glance • DNA isolation directly from human whole blood or plasma samples: No pre-treatment of primary samples is required before extraction. • “Ready-to-Use” DNA with high yield and purity • Fast process times: 96 samples in less than 60 minutes • Long DNA fragments: up to 200 kb, suitable for NGS • High recovery rates • Autonomous system with regard to downstream assays Specifications: Manufacturer: Perkin Elmer Type: Chemagic 360-D Throughput: approximately 96 samples per run Sample capacity: 12, 24, and 96 Volume: 10 microliters to 10 ml Extraction heads (Chemagic rod heads): 96 Number of samples: 1 – 96 Sample volumes: 10 µl to 400 µl Tube plates: 96-well plates Extensive kit portfolio – whole blood, saliva, serum/plasma, etc. Hfsdpfjyk Upmjx An Nsn No cross-contamination Revolutionary compact benchtop design Computer workstation with Chemagic software LCD monitor, keyboard, mouse Power supply: 100–240 V~ (AC), 50/60 Hz Size/Dimensions: Width: 900 mm (1500 mm with connected display and door open) Depth: 820 mm (1000 mm with door open) Height: 900 mm Weight: 140 kg Year of manufacture: 2024 Video link Chemagic 360-D You can find more items – new and used – in our shop! International shipping costs on request!

Condition: used, This listing is for a Qiagen QIAsymphony SP Sample Preparation Fully-Automated DNA RNA Purification Hfjdpfxoxzg Nxe An Non Very good working and cosmetic condition The QIAsymphony SP is a versatile nucleic acid purification instrument providing high-quality nucleic acids compatible with with most common downstream assay technologies, such as real-time PCR, digital PCR, and next generation sequencing (NGS). The large range of a dedicated QIAsymphony kits enables optimized purification of genomic DNA, cell-free circulating DNA, RNA, bacterial and viral nucleic acids from a wide range of starting materials Features: Purification of high-quality genomic DNA, pathogen DNA/RNA, cell-free circulating DNA and cellular RNA 1-96 samples in 4 batches, from smallest forensic samples to 10 ml sample volumes Standardized protocols for diagnostic, routine, research and forensic applications Flexible loading of new samples during a run Protocols customizable (protocol steps, labware, etc.) on demand Traceability and LIMS compatibility Compatible with most commonly used sample tubes and elution tubes and plates Compatibile with QIAsymphony DSP kits for diagnostic workflows. Specification: Minimum input volume: 200µl Elution volume: 30-500µl Dimensions: 128 x 103 x 73cm (w x d x h) Weight: 175kg Electric supply: 100 - 230VAC 50/60Hz

Condition: used, This listing is for a Qiagen QIAsymphony SP Sample Preparation Fully-Automated DNA RNA Purification Very good working and cosmetic condition The QIAsymphony SP is a versatile nucleic acid purification instrument providing high-quality nucleic acids compatible with with most common downstream assay technologies, such as real-time PCR, digital PCR, and next generation sequencing (NGS). The large range of a dedicated QIAsymphony kits enables optimized purification of genomic DNA, cell-free circulating DNA, RNA, bacterial and viral nucleic acids from a wide range of starting materials Features: Purification of high-quality genomic DNA, pathogen DNA/RNA, cell-free circulating DNA and cellular RNA 1-96 samples in 4 batches, from smallest forensic samples to 10 ml sample volumes Standardized protocols for diagnostic, routine, research and forensic applications Flexible loading of new samples during a run Protocols customizable (protocol steps, labware, etc.) on demand Hodpfx Ajxzgzujn Nsfn Traceability and LIMS compatibility Compatible with most commonly used sample tubes and elution tubes and plates Compatibile with QIAsymphony DSP kits for diagnostic workflows. Specification: Minimum input volume: 200µl Elution volume: 30-500µl Dimensions: 128 x 103 x 73cm (w x d x h) Weight: 175kg Electric supply: 100 - 230VAC 50/60Hz

Condition: used, This listing is for a Qiagen PyroMark Q24 Advanced Sequencer For advanced methylation and mutation quantification in long sequence runs using Pyrosequencing Advanced technology, software, and chemistry for long sequence runs Quantitative methylation analysis at consecutive CpG or CpN sites Improved quantification of sequence variations at any sequence position Easy and improved base calling functionality Assay versatility on the same instrument and in the same run PyroMark Q24 Advanced has improved Pyrosequencing technology to provide even better real-time sequence-based detection and quantification than before. PyroMark Q24 Advanced features advanced technology, software, and chemistry, and is highly suited for analyzing any kind of sequence variation, particularly DNA methylation at CpG or CpN sites, complex mutations, or for de novo sequencing applications such as microbial typing. Can be refurbished on request, refurbishment not included in price. Hsdexzh Suopfx An Nefn

Condition: good (used), Year of construction: 2006, SpectruMedix RVL 9612 Genetic Analysis System including PC and accessories This device is suitable for molecular biology laboratories, research institutions, and universities for genetic analysis (e.g., DNA sequencing, genotyping). Model: RVL 9612 Manufacturer: SpectruMedix LLC, State College, PA, USA Serial number: 1102 Revision: 2.0 Year of manufacture / Date of production: March 17, 2006 Supply voltage: 115/230 V Frequency: 50/60 Hz Power consumption: 3300 W Phases: 1 (single-phase operation) Certificates: CE compliant (HCS CE-D) Hfsdpfx Ajxlrvxon Nsn Condition: Used (see pictures). Note: For detailed technical data and processing instructions, we strongly recommend consulting the original data sheets or contacting the manufacturer directly. You can find more new and used items in our shop! International shipping costs available upon request!

Condition: used, Thermo Fisher Scientific KingFisher FLEX Magnetic Particle Processor 4 units available Hjdpfx Aez I S D Sen Nefn Manufacturer: Thermo Fisher Scientific Model: KingFisher FLEX Equipment Type: Automated Magnetic Particle Processor / Nucleic Acid Purification System Application: Automated DNA/RNA purification and sample preparation Description: The Thermo Fisher Scientific KingFisher FLEX is an automated magnetic particle processing system designed for high-throughput purification and sample preparation. The KingFisher FLEX uses magnetic bead technology to automate the processing of biological samples, providing consistent and reproducible purification of DNA, RNA, proteins and other biological targets. It is widely used in molecular biology, genomics, biotechnology, pharmaceutical research and clinical laboratory environments. The system is particularly suited to laboratories looking to automate repetitive sample preparation and purification workflows while reducing manual handling and improving throughput. Key Features: Automated magnetic bead-based sample processing Designed for high-throughput laboratory workflows Suitable for DNA and RNA purification Can be used for protein and other biomolecule purification applications Programmable automated processing protocols Consistent and reproducible sample preparation Suitable for research, biotechnology and pharmaceutical laboratories Multiple plate formats supported depending on configuration User-friendly automated operation Compact laboratory footprint Typical Applications: DNA purification RNA purification Nucleic acid extraction PCR sample preparation Genomics and molecular biology Next-generation sequencing workflows Protein purification Pharmaceutical research Biotechnology research High-throughput sample preparation Removed from pharma plant in Cork, IE. Devices are in very good condition. Sold as seen ----- Keywords: Thermo Fisher, Thermo Scientific, KingFisher FLEX, King Fisher Flex, KingFisher Flex Purification System, magnetic particle processor, magnetic bead processor, DNA extraction, RNA extraction, DNA purification, RNA purification, nucleic acid extraction, sample preparation, automated sample preparation, molecular biology, genomics, biotechnology, pharmaceutical laboratory, laboratory automation, PCR preparation, NGS, next generation sequencing, protein purification, research laboratory equipment, scientific equipment, lab equipment.

Condition: used, This listing is for a Life Technologies Ion Torrent OneTouch 2 with OneTouch ES The Life Technologies Ion OneTouch 2 with Ion OneTouch ES comprises two modules: the Ion OneTouch™ 2 Instrument and the Ion OneTouch™ ES (enrichment system). It simplifies the workflows by providing an automated solution for scalable and reproducible template preparation. It is used for DNA sequencing in healthcare, lab and life sciences. It streamlines the overall Ion semiconductor sequencing workflow, yielding significant time savings and increasing sequencing productivity. The system enables parallel template processing with sample sequencing on the Ion Proton™ or Ion PGM™ sequencers. This reduces the time from sample to sequence to a single day and enables processing of multiple samples per day. The combination of Ion semiconductor sequencing and the Ion OneTouch™ 2 System maximizes the speed of each experiment and minimizes the overall time to completion for each project. The modular design also allows for QC of Ion Sphere™ particles, to maximize experimental control and the success of each experiment. Hedpfexzg Ubex An Nofn Features: Integrates multiple manual template preparation workflows into a single system Enables parallel processing of multiple samples per day through modular design Supports scalable template preparation for all Ion semiconductor sequencing chips Supports up to 400 bases on the Ion PGM™ System and up to 200 bases on the Ion Proton™ System Includes a full thermal cycling modality for amplification for quick optimization of thermal cycling parameters Employs a peristaltic pump fluidic system that eliminates the need for gas Fits easily on any benchtop with its small instrument footprint Specifications: Weight, OneTouch 2 23 lbs. (10.4 kg.) Weight, OneTouch ES 12 lbs. (5.4 kg.) Dimensions, OneTouch 2 12" W x 16" D x 14" H (30 x 41 x 36 cm) Dimensions, OneTouch ES 9.5" W x 12.5" D x 11" H (24 x 32 x 28 cm) Operating Humidity 20%-80% (non-condensing) Operating Temperature 15°C-25°C Multiplex Capability Up to 384 barcoded libraries High Throughput Compatibility Automated Protocols, Multiplexing, High Throughput-Compatible Power 100-240 VAC, 50/60 Hz, 5.5 A max

Condition: used, This listing is for the Applied Biosystems ProFlex PCR Sytem The unit is in full working condition and is ready for immediate release. Hfjdpjx Syrqefx An Non The Applied Biosystems ProFlex PCR System is a thermal cycler/performance PCR instrument designed for amplifying DNA through PCR — a core technique in molecular biology for cloning, sequencing, gene expression studies, genotyping, and other applications. It’s used in research, teaching, and clinical lab settings (research use only; not for diagnostic procedures)

Condition: used, This listing is for the PerkinElmer Chemagic™ 360 – Automated Nucleic Acid Extraction System The unit is in full working condition and is ready for immediate use. Each unit is on heavy duty trolley with lockable castors The Perkin Elmer Chemagic™ 360 is a high-throughput, compact benchtop instrument designed for automated DNA and RNA extraction from a wide range of sample types, including blood, plasma, saliva, tissues, and FFPE samples. It uses chemagen’s proprietary M-PVA magnetic bead technology for the efficient and reliable purification of nucleic acids, delivering high yields with excellent purity. Key Features & Benefits Flexible Sample Volume: Processes volumes from 10 µL to 10 mL, supporting a variety of protocols and sample types. High Throughput: Handles up to 96 samples per run, ideal for biobanks, clinical labs, and research institutions. Large Kit Portion Compatibility: Supports processing of large-volume samples with high reagent capacity. Cross-Contamination Prevention: Engineered protocols and magnetic separation minimize the risk of sample-to-sample contamination. Mixed Sample Types: Able to process different sample materials in the same run, enhancing workflow efficiency. Integration Ready: Compatible with automated liquid handling platforms for streamlined workflows. Compact Footprint: Space-saving design with dimensions of 80 x 80 x 90 cm (L x W x H), suitable for constrained lab environments. Advanced Sample Handling: Offers convenient and improved sample management, reducing hands-on time. Barcode Scanning: Enables automated sample tracking and improves traceability throughout the process. LIMS Integration: Produces LIMS-compatible log files, supporting full data traceability and compliance. User-friendly Interface: Intuitive software for easy setup, protocol customization, and real-time monitoring. Technical Specifications Sample Capacity: 1–96 per run Hfjdexhgm Rjpfx An Nen Sample Volume Range: 10 µL – 10 mL Processing Time: ~45 minutes for 400 µL whole blood Dimensions (L x W x H): 80 cm x 80 cm x 90 cm Weight: 140 kg Power Supply: 100–240 VAC, 50/60 Hz Ideal Applications Next-Generation Sequencing (NGS) PCR and qPCR Genotyping and MLPA Clinical Diagnostics Biobank Sample Preparation

Condition: good (used), functionality: fully functional, The innovative QIAcube controls integrated components including a centrifuge, heated shaker, pipetting system and robotic gripper. This enables the QIAcube to fully automate more than 40 QIAGEN spin column kits. The QIAcube comes preinstalled with a variety of protocols for purification of RNA, genomic DNA, plasmid DNA, viral nucleic acids and proteins, plus DNA and RNA cleanup. All standard protocols in the expanding range can also be downloaded for free. In addition, custom protocols tailored to your specific application requirements can also be requested. The QIAcube is well suited for academic research laboratories and pharmaceutical, biotechnology and biomedical research laboratories performing applications such as: Sequencing / sequencing analysis Gene expression analysis genotyping proteomics Centrifuge: 12,000 x g maximum, swing-out rotor with 12 positions, maximum 45° Humidity: Relative humidity of 10-75% (non-condensing) Instrument dimensions: 650 x 620 x 570 mm Operating temperature: 18 – 28 ° C Pipetting system: Syringe size 1 ml, pipetting range 5-900 μl Samples per run: 1-12 samples per run Hedpfxovzr Nbs An Njfn Shaker: Speed 100-2000 rpm, amplitude 2 mm, heating range room temperature to 70°C, ramp time of

Condition: used, This listing is for the AATI Fragment Analyser capillary electrophoresis system The unit is in full working condition and is ready for immediate use The AATI Fragment Analyzer is an advanced automated capillary electrophoresis system designed for precise analysis of DNA and RNA fragments. Developed by Advanced Analytical Technologies Inc. (AATI), the instrument provides high-resolution sizing, quantification, and quality assessment of nucleic acid samples. Widely used in genomics, molecular biology, and next-generation sequencing workflows, the system streamlines fragment analysis by replacing traditional gel electrophoresis with a faster, automated process. It allows laboratories to process multiple samples simultaneously, delivering reproducible results with minimal manual intervention. The instrument supports a variety of assay kits for DNA and RNA analysis, enabling applications such as NGS library quality control, PCR fragment verification, and RNA integrity assessment. With integrated software for data analysis and reporting, users can easily visualize fragment distribution, concentration, and size profiles. Key Features: Automated capillary electrophoresis for DNA and RNA analysis Hsdpfx Asyr Nl Son Nsfn High-resolution fragment sizing and quantification High-throughput sample processing Ideal for NGS library QC, PCR product analysis, and RNA quality checks User-friendly software with clear electropherogram and gel-style outputs The AATI Fragment Analyzer is a reliable solution for laboratories requiring accurate nucleic acid fragment analysis with improved efficiency and reproducibility

Condition: good (used), Year of construction: 2016, functionality: fully functional, power: 5.5 kW (7.48 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 40 t, stroke length: 170 mm, operating speed: 10 mm/s, reverse speed: 170 mm/s, table width: 90 mm, table length: 1,270 mm, table height: 850 mm, throat depth: 350 mm, clearance between the columns: 1,050 mm, oil tank capacity: 80 l, total length: 2,150 mm, total width: 1,650 mm, total height: 2,300 mm, overall weight: 3,250 kg, year of last overhaul: 2025, Equipment: CE marking, safety light barrier, 2016 Ermaksan Speed-Bend Pro 1270 x 40 CNC Press Brake – 6 Axis – Delem DA-66T Control Used 2016 Ermaksan Speed-Bend Pro 1270 x 40 CNC hydraulic press brake for sale in Ireland. 6-axis CNC press brake with Delem DA-66T graphic control, Y1, Y2, X, R, Z1 and Z2 axes, tooling, laser guards. Manufacturer: Ermaksan Model: Speed-Bend(SB) Pro 1270 x 40 Axes: 6 Year: 2016 Capacity: 1270mm x 40T Control: Delem DA66T Description 2016 Ermaksan Speed-Bend Pro 1270 x 40 CNC Press Brake, a compact, high-quality 6-axis CNC hydraulic press brake ideal for precision sheet metal bending, fabrication workshops, engineering companies and production environments. This Ermaksan Speed-Bend Pro 1270 x 40 offers a bending length of 1270 mm and a bending power of 40 tonnes. It is fitted with a Delem DA-66T graphic CNC control, providing a clear touch-screen interface for accurate programming, bend sequence calculation, tooling setup and repeatable production bending. The machine is in good condition. It comes complete with Euro-style top and bottom press brake tooling, laser guards, foot pedal, quick-release top tool clamps and rear safety doors, making it a well-equipped used press brake ready for immediate inspection and production use. This is a superb opportunity to purchase a late-model, compact Ermaksan CNC press brake with a desirable 6-axis specification, ideal for companies looking for a reliable used hydraulic press brake in Ireland, the UK or Europe. Key Features Manufacturer: Ermaksan Model: Speed-Bend Pro 1270 x 40 / SB PRO 1270-40 Year: 2016 Type: CNC hydraulic press brake Bending length: 1270 mm Bending power: 40 tonnes Axis configuration: 6 Axis CNC controlled axes: Y1, Y2, X, R, Z1 and Z2 Control: Delem DA-66T Graphic CNC Control Hfsdjzdak Ajpfx An Njn Condition: Good condition Tooling: Complete with Euro-style top and bottom tools Safety: Laser guards and rear safety doors Clamping: Quick-release top tool clamps Includes: Foot pedal Suitable for: Sheet metal fabrication, precision bending, general engineering, subcontract fabrication and production bending Technical Specifications – SB PRO 1270-40Model: SB PRO 1270-40 Bending length: 1270 mm Bending power: 40 tonnes Distance between columns: 1050 mm Y-axis rapid speed: 140 mm/s Y-axis working speed: 10 mm/s Y-axis return speed: 170 mm/s X-axis travel: 500 mm X-axis speed: 500 mm/s R-axis travel: 250 mm R-axis speed: 350 mm/s Z1 / Z2-axis travel speed: 1000 mm/s Backgauge finger blocks: 2 Oil capacity: 80 litres Motor power: 5.5 kW Stroke: 170 mm Daylight: 387 mm Throat depth: 350 mm Table height: 850 mm Table width: 90 mm Machine Dimensions: 2150 x 1650 x 2300mm Machine weight: 3250 kg Standard / Included Equipment This used Ermaksan Speed-Bend Pro press brake is supplied with: 6 CNC axes: Y1, Y2, X, R, Z1 and Z2 Delem DA-66T graphic CNC control Euro-style top press brake tools Euro-style bottom press brake tools Laser safety guards Foot pedal Quick-release top tool clamps Rear safety doors Backgauge finger blocks Sheet support arms Notes: *Specifications are given in good faith but not guaranteed*

Condition: ready for operation (used), Year of construction: 2005, operating hours: 3,648 h, functionality: fully functional, travel distance X-axis: 625 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 650 mm, controller model: Siemens Sinumerik 840D, spindle speed (max.): 10,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range X-axis: 625 mm Travel range Y-axis: 650 mm Travel range Z-axis: 650 mm B-axis swivel range: 360° B-axis resolution: 0.001° B-axis speed: 100 rpm Spindle speed: 50–10,000 rpm Spindle power: 24 / 37 kW Hsdpfxjz Izc Ro An Nefn Spindle torque: 250 / 350 Nm Spindle operating hours: 3,648 h Tool interface: HSK-A63 according to DIN 69893 Number of pallets: 2 Pallet size: 500 × 400 mm Pallet load capacity: 400 kg Pallet change time: 8 / 5 s T-slots: according to DIN 55201 Magazine capacity: 60 Max. tool diameter: 80 mm Max. tool diameter with free adjacent slots: 160 mm Max. tool length: 350 mm Max. tool weight: 10 kg Max. total weight of tools: 200 kg MACHINE DETAILS Control system: Siemens Sinumerik 840D Coolant tank volume: approx. 1,100 l Coolant pressure: 50 bar Dimensions & Weight Dimensions (L x W): 5,800 x 4,800 mm Machine weight: 12,800 kg Total automatic operation: 32,099 h Total operating hours: 20,326 h Spindle hours: 3,648 h EQUIPMENT Pallet changer Chain magazine with 60 tool positions Knoll coolant unit with filter fleece Emulsion cooling inside and outside Renishaw measuring probe Tool breakage monitoring in the magazine Chip conveyor Sound enclosure Paper band filter Rinsing gun at the setup station Closed work area enclosure according to UVV Pallet sequence operation Network connection Ethernet interface Technical documentation Layout plan

Condition: ready for operation (used), Year of construction: 2000, operating hours: 23,574 h, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 560 mm, travel distance Z-axis: 560 mm, controller model: Siemens Sinumerik 840D, spindle speed (max.): 8,000 rpm, No minimum price – guaranteed sale to the highest bidder! The following components of the machine have been renewed: Motor and pump of the hydraulic system Hydraulic and pneumatic hoses (partially) Control cabinet LT module replaced Drum of the Knoll system TECHNICAL DETAILS Travel range X-axis: 600 mm Travel range Y-axis: 560 mm Travel range Z-axis: 560 mm B-axis: 360 x 0.001 (60 rpm) Spindle speed: 8,000 rpm Table size: 6 pallets, each 500 x 400 mm Table width: 400 mm Table length: 500 mm Table load capacity: 350 kg Working feed rate: 1 - 60,000 mm/min Rapid traverse: 60 m/min MACHINE DETAILS Hfjdpfx Ansz Izave Nen Control model: Siemens Sinumerik 840D Overall length: 7,000 mm Overall width: 5,000 mm Coolant supply: 50 bar Coolant system: approx. 1,100 L Motor power: 13 kW / 20 kW Torque: 124 / 191 Nm Total power consumption: 20 kW Dimensions & Weight Space requirement (L x W): 7 x 5 m Machine weight: approx. 16,000 kg Operating hours Power-on counter: approx. 48,804 h Spindle running time: 23,574 h total EQUIPMENT Documentation/manual Speed infinitely adjustable Chip conveyor Knoll cooling unit with drum filter (30/40/50 bar via M-command) Tool measurement: Renishaw measuring probe Tool breakage monitoring in the machining area Pallet storage space (4 places) Pallet sequence operation Enclosed work area enclosure according to UVV Network capability Technical documents & layout plan

Condition: good (used), Year of construction: 2004, I sell the automatic pneumatic end cutting saw OMGA T521 OPT 6600, year 2004. Input table automatic feeding 6,60m (pusher system) Outut table 3,00m Total length: 10,50m Optimising with automatic cutting sequence modes. Fluorescent chalk sensor reader. Available immediately. Hjdpfx Aoz Suzpjn Nofn CE version. Documentation included.

Condition: used, Year of construction: 2016, Overview This Represa LAGUI 3.2 is an automatic rotary labeling machine for self-adhesive labels on cylindrical bottles, built in 2016 by the Spanish manufacturer Represa Construcciones Mecánicas. It has been used for wine bottling and is configured with three labeling heads for front label, back label and tax strip stamp on 75 cl and 150 cl wine bottles. The bottles are spaced by an infeed screw, transferred by starwheels onto rotating bottle plates and labeled in sequence by the three heads; each head is adjustable in height, angle and travel. Bottle height is set automatically from the touch panel, and up to 30 formats (bottle heights and label sets) can be stored and recalled for fast changeovers. Technical data - Manufacturer: Represa Construcciones Mecánicas - Model: LAGUI 3.2 - Year of manufacture: 2016 - Machine type: rotary self-adhesive labeler for cylindrical bottles - Labeling heads: 3 (front label, back label, tax strip stamp) - Output: up to 3,000 bottles per hour, adjustable - Bottle formats: 75 cl and 150 cl - Format memory: up to 30 formats - Power supply: 400 V - Compressed air: 2.5 bar minimum operating pressure - Construction: stainless steel frame with transparent safety guarding Equipment - Bottle infeed screw and transfer starwheels Hfedpoz Syvfofx An Nsn - Rotating bottle plates - 3 self-adhesive labeling heads with label detection sensors - Photoelectric bottle detection - Automatic height adjustment of the machine and the heads - Control panel with multifunction touch screen on a 180° swivel arm - Safety-interlocked doors and emergency stop - CE declaration and operating manual (Spanish) Condition The machine is still installed and can be inspected on site by appointment. Availability Available immediately. Location: Spain.

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, power: 18.5 kW (25.15 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 175 t, stroke length: 265 mm, operating speed: 10 mm/s, reverse speed: 100 mm/s, table width: 104 mm, table length: 4,050 mm, table height: 900 mm, throat depth: 410 mm, distance table to ram: 530 mm, clearance between the columns: 3,600 mm, oil tank capacity: 250 l, total length: 6,450 mm, total width: 2,650 mm, total height: 2,750 mm, overall weight: 12,500 kg, number of support arms: 2, number of axes: 6, Equipment: CE marking, safety light barrier, 2013 Durma AD-S 40175 CNC Press Brake – 6 Axis – Cybelec ModEva 10S Control Used 2013 Durma AD-S 40175 CNC hydraulic press brake for sale in Ireland. 6-axis CNC press brake with Cybelec ModEva 10S graphic control, Y1, Y2, X, R, Z1 and Z2 axes, CNC motorised crowning, laser guards, tooling and rear safety doors. Manufacturer: Durma Model: AD-S 40175 Axes: 6 Year: 2013 Capacity: 4000mm x 175T Control: Cybelec ModEva 10S Control Includes: Large Selection of Top & Bottom Tooling Description 2013 Durma AD-S 40175 CNC Press Brake, a high-quality 6-axis CNC hydraulic press brake with 4050 mm bending length and 175 tonne bending force. This machine is ideal for precision sheet metal bending, fabrication workshops, engineering companies, subcontract metalwork and production environments requiring a robust, accurate and well-specified press brake. This Durma AD-S 40175 is fitted with a Cybelec ModEva 10S Graphic CNC Control, offering 3D graphical programming and automatic bend sequences. The machine has 6 CNC controlled axes: Y1, Y2, X, R, Z1 and Z2, giving excellent flexibility for accurate bending and efficient backgauge positioning. The machine is in very good condition and comes complete with a large selection of Euro-style top and bottom press brake tools, laser guards, foot pedal, CNC controlled motorised crowning, quick-release top tool clamps and rear safety doors. Key Features Bending length: 4050 mm Bending force: 175 tonnes Axis configuration: 6 Axis CNC controlled axes: Y1, Y2, X, R, Z1 and Z2 Control: Cybelec ModEva 10S Graphic CNC Control Condition: Very good condition Hodpfsz Imc Nex An Nefn Crowning: CNC controlled motorised crowning Tooling: Complete with Euro-style top and bottom tools Safety: Laser guards and rear safety doors Clamping: Quick-release top tool clamps Includes: Foot pedal Suitable for: Sheet metal fabrication, precision bending, general engineering, subcontract fabrication and production bending Technical Specifications Model: AD-S 40175 Bending force: 175 tonnes Bending length: 4050 mm Distance between columns: 3600 mm Y-axis rapid speed: 120 mm/s Y-axis working speed: 10 mm/s Y-axis return speed: 100 mm/s Crowning: Motorised Daylight: 530 mm Table width: 104 mm Table height: 900 mm Stroke: 265 mm Throat depth: 410 mm Support arms: 2 Backgauge finger blocks: 2 X-axis travel speed: 500 mm/s X-axis travel: 650 mm R-axis travel speed: 350 mm/s R-axis travel: 250 mm Motor power: 18.5 kW Oil tank capacity: 250 litres Machine dimensions: 6450x2650x2750 mm Machine weight: 12,500 kg Cybelec ModEva 10S Graphic CNC Control The machine is fitted with a Cybelec ModEva 10S Graphic CNC Control, a user-friendly press brake control designed for graphical programming and efficient bending setup. Control features include: 3D graphical control interface 10.4” colour TFT screen 128 MB RAM 128 DM main memory Easy Cursor operation Automatic bend sequence calculation Single-page part programming capability CAD/CAM sequence viewing support Included Equipment This used Durma AD-S 40175 press brake is supplied with: 6 CNC controlled axes: Y1, Y2, X, R, Z1 and Z2 Cybelec ModEva 10S Graphic CNC Control Large Selection of Euro-style top & bottom tooling CNC controlled motorised crowning Laser safety guards Foot pedal Quick-release top tool clamps Rear safety doors Front support arms Backgauge finger blocks

Year of construction: 2024, condition: like new (used), Compact device for automated nucleic acid purification The Perkin Elmer Chemagic 360 is an automated benchtop system for the isolation of nucleic acids (DNA and RNA) from a variety of sample materials. It uses Chemagen's magnetic bead technology to obtain highly pure nucleic acids for various downstream applications. With dimensions of only 80 x 80 cm and its unique sample volume flexibility, the Chemagic 360 is an innovative instrument that can be adapted to almost all of your nucleic acid purification requirements. By using the proven M-PVA magnetic bead technology, the Chemagic 360 delivers high yields of highly pure nucleic acids, which are suitable for a variety of downstream applications such as NGS, MLPA, genotyping, and PCR. Features at a glance • Optimized design to prevent cross-contamination • Sample volume from 10 µl - 10 ml • Throughput of 96 to 4000 samples per day • Compact design • Ultra-fast protocols for DNA purification available • Flexible reagent dispensing to keep operating costs low • User-friendly interface enables easy and quick installation • Easy integration into liquid handling platforms The advantages at a glance • DNA isolation directly from human whole blood or plasma samples: No pretreatment of primary samples is required before extraction • "Ready-to-use" DNA with high yield and purity Hedsyk Uy Sjpfx An Njfn • Fast process times: 96 samples in less than 60 minutes • Long DNA fragments: up to 200 kb, suitable for NGS • High recovery rates • Autonomous system with regard to downstream assays Specifications: Manufacturer: Perkin Elmer Type: Chemagic 360 Throughput: approximately 96 samples per run Sample capacity: 12, 24 and 96 Volume: 10 microliters to 10 ml Extraction heads (chemagic probe heads): 96 Number of samples: 1 – 96 Sample volumes: 10 µl to 400 µl Tube plates: 96-well plates Extensive kit portfolio – whole blood, saliva, serum/plasma, etc. No cross-contamination Revolutionary, compact benchtop design LCD monitor, keyboard, mouse Power supply: 100–240 V~ (AC), 50/60 Hz Size/dimensions: 800 x 800 x 900 mm Weight: 140 kg Year of manufacture: 2024 Video link Chemagic 360 More items - new and used - can be found in our shop! International shipping costs on request!

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, power: 15 kW (20.39 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 175 t, stroke length: 275 mm, operating speed: 12 mm/s, reverse speed: 190 mm/s, table length: 3,100 mm, table height: 900 mm, throat depth: 410 mm, distance table to ram: 550 mm, clearance between the columns: 2,600 mm, oil tank capacity: 300 l, total length: 5,025 mm, total width: 2,150 mm, total height: 2,680 mm, overall weight: 9,086 kg, Equipment: CE marking, documentation/manual, safety light barrier, 2022 Ermaksan Speed-Bend PRO 3100x175 CNC Press Brake 2022 Ermaksan Speed-Bend PRO 3100x175 CNC press brake in very good condition. 175T x 3100mm, 6 axis, Delem DA66TX, CNC crowning, laser guards, generous tooling package included. Machine Manufacturer: Ermaksan Model: Speed Bend Pro 3100 x 175T Machine Type: 6 Axis CNC Pressbrake Capacity: 3100 x 175T Year: 2022 Control: Delem DA66TX Condition: Very Good Description Ermaksan Speed-Bend Pro 6 Axis CNC Hydraulic Press Brake with Delem DA66TX Control. Available now, this 2022 Ermaksan Speed-Bend PRO 3100x175 CNC Press Brake is a high-quality, modern hydraulic press brake in very good condition. This is a 6 axis machine with Y1, Y2, X, R, Z1 and Z2 axes, fitted with a Delem DA66TX CNC control, pneumatic top tool clamping, CNC crowning, laser guards, wanderer type foot pedal, and supplied with generous selection of top and bottom tooling. Ideal for sheet metal fabrication, precision bending, stainless steel work, mild steel fabrication, aluminium bending, agricultural fabrication, general engineering and production workshops. Key Features 2022 Ermaksan Speed-Bend PRO 3100x175 175 tonne bending capacity 3100mm bending length 6 axis CNC press brake Y1, Y2, X, R, Z1 & Z2 axes Delem DA66TX CNC control Pneumatic top tool clamping Package of Top and bottom tooling included CNC / motorised crowning Laser safety guards Wanderer type foot pedal Very good condition Excellent machine for fabrication and production bending work Capacity & Main Machine Data Manufacturer: Ermaksan Model: Speed-Bend PRO 3100x175 Year: 2022 Machine Type: CNC hydraulic press brake Bending Length: 3100mm Bending Force: 175 tonnes Distance Between Columns: 2600mm Axes: Y1, Y2, X, R, Z1, Z2 Crowning: Motorised / CNC crowning Backgauge Finger Blocks: 2 Speeds & Axis Travel Y Rapid Speed: 180mm/s Y Working Speed: 12mm/s Y Return Speed: 190mm/s Hodpfoz Dn Huox An Njfn X Axis Travel: 800mm X Axis Speed: 500mm/s R Axis Travel: 250mm R Axis Speed: 350mm/s Z1 / Z2 Axis Travel Speed: 1000mm/s Stroke, Daylight & Frame Stroke: 275mm Daylight: 550mm Throat Depth: 410mm Table Height: 900mm Table Width: 90mm Power, Size & Weight Oil Capacity: 300 litres Motor Power: 15kW Approx. Length: 5025mm Approx. Height: 2680mm Approx. Width: 2150mm Approx. Weight: 9086kg Delem DA66TX CNC Control Control Features Include 2D graphical touch-screen programming High-resolution colour TFT display Automatic bend sequence calculation Collision detection 3D machine setup with multiple tool stations USB / peripheral interfacing Product and tool memory Profile-TL offline software support User-friendly Delem touch navigation Delem’s DA-66T platform is listed by Delem as a 2D graphical press brake control with automatic bend sequence calculation, collision detection, full 3D machine setup, USB interfacing, 17" high-resolution colour TFT display and Profile-TL offline software support. Included Equipment Pneumatic top tool clamping Lots of Top tooling Lots of Bottom tooling CNC crowning Laser guards Wanderer type foot pedal 6 axis CNC backgauge system Delem DA66TX control Typical Applications Sheet metal fabrication CNC press brake bending Mild steel bending Stainless steel bending Aluminium bending Box and pan type components Architectural metalwork Agricultural fabrication General engineering workshops Production bending work

Condition: used, Year of construction: 2007, functionality: fully functional, Equipment: CE marking, documentation/manual, Holz-Her Sprint 1317 Edge Banding Machine Manufacturer: Holz-Her Model: Sprint 1317 Year of Manufacture: 2007 Equipment • Pre-milling unit • Gluing unit • Roller magazine for roller edges • Automatic trimming • Multi-milling unit (flush trimming / radius milling / chamfering) • Corner rounding unit • Profile scraping blade • Surface scraping blade • Polishing unit • Automatic unit adjustment • Control panel with operating panel • 400 V connection Technical Data • Workpiece height up to 60 mm • Roller edges up to 3 mm • Edges up to 8 mm • Feed rate up to 18 m/min • Minimum workpiece length 180 mm • Minimum workpiece width 60 mm Description For sale is a Holz-Her Sprint 1317 edge banding machine in very good condition. The machine has extensive equipment for professional edge processing and impresses with its robust construction and precise processing results. Hfjdpfx Ajz R A U Isn Nen Processing sequence • Pre-milling • Glue application • Roller edge banding • Automatic trimming • Flush and radius milling • Corner rounding • Profile scraping blade • Surface scraping blade • Polishing The machine was in use until recently and can be inspected by appointment.

Condition: ready for operation (used), Year of construction: 2013, operating hours: 7,358 h, functionality: fully functional, machine/vehicle number: 6LUD00036, travel distance X-axis: 620 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 460 mm, feed length X-axis: 620 mm, feed length Y-axis: 620 mm, feed length Z-axis: 460 mm, feed rate X-axis: 36,000 m/min, feed rate Y-axis: 36,000 m/min, feed rate Z-axis: 36,000 m/min, torque: 108 Nm, controller manufacturer: Heidenhain, controller model: iTNC530, workpiece length (max.): 500 mm, workpiece width (max.): 400 mm, workpiece height (max.): 350 mm, workpiece diameter (max.): 680 mm, workpiece weight (max.): 300 kg, total height: 3,400 mm, total length: 4,600 mm, total width: 2,700 mm, table width: 600 mm, table height: 755 mm, table length: 600 mm, table load: 300 kg, rotary table diameter: 600 mm, rotational speed (min.): 20 rpm, rotational speed (max.): 12,000 rpm, overall weight: 8,500 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 12,000 rpm, operating hours of spindle: 5,303 h, coolant supply: 18 bar, distance table center to spindle nose: 50 mm, spindle motor power: 17,000 W, spindle nose: SK40, number of spindles: 1, number of slots in tool magazine: 100, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, Commissioned 4/2014 Table rotation, C-axis: 360° Table swivel, B-axis: -50° to +110° Distance from spindle nose to table: 150 mm Table clamping surface: Ø 650 Hfjdjz Diq Uopfx An Njn Table load capacity, max.: 300 kg Table slots: 5 x 18H7 x 100 mm Centering bore: Ø 50 H7 x 30 mm Workpiece size, max.: Ø 520 x 330 mm Machine accuracy: VDI I DGQ 3441* Positioning accuracy: +/- 0.006 mm* Axis resolution: 0.001 mm* *determined at a constant ambient temperature of 20°C +/- 1°C Main spindle: Main drive, AC motor, direct drive Drive power (100% / 25% ED): 10.0 / 17.0 kW Speed range, stepless: 20 - 12000 rpm Spindle taper: SK 40 DIN 69871 Torque at (100% / ED): 63.7 / 108.6 Nm Axis drives: Axes X, Y, Z: AC motors Axes B, C: AC motors Travel speeds: Rapid traverse in axes X, Y, Z: 36 m/min Speed, max. B-axis: 25 rpm Speed, max. C-axis: 25 rpm Acceleration X, Y, Z: 6.5 m/s² Coolant system: External tool cooling via external nozzles Coolant tank: 280 l Operating pressure, external: 0.9 bar Coolant system, internal tool cooling DIN 69871 Form A Operating pressure, internal coolant supply: 18.0 bar Manual rinsing of the work area via an additional gun Standard accessories: - CNC control: Heidenhain iTNC 530, full simultaneous 5-axis version - Handwheel 410 (Heidenhain) - Digital axis drives - Digital spindle drive - Swarf conveyor with discharge height 800 mm • Spindle cooling – radiators – plate cooling for spindle motor - Full protective enclosure with cabin roof Tool magazine VZG 65 5A by Indunorm: Number of tools: 100, with a tool length of up to 320 mm / can be converted to 125 tools, then a tool length of only 200 mm is possible. Tool diameter, max.: 80 mm Tool diameter, max.: 130 mm (with free adjacent positions) Tool change with double gripper - Linear path measuring system in axes X / Y / Z (glass scale) - Direct encoder in axes B / C - Temperature compensation - IR measuring probe – 3D Software - Option - iTNC 530 Kinematic-Opt • Calibration software Internal tool cooling 18 bar • Coolant tank • Internal tool cooling: 280 L DIN 69871 Form A • Double-circuit filter • Switchable filter cartridges • Filtration rate: 10 µm Band filter system PRODUCTION - LINE - RT 100 Automatic pallet changing system Loading and unloading via a linear axis system: Handling data: Handling weight, max.: 100 kg (35 kg) Pallet capacity: 6 pallet positions up to 400 x 400 mm: Control: PLC control with integrated control cabinet incl. switching and control components incl. software for the automatic sequence Zero point clamping system 320 x 320 x 60 mm - Clamping via 4 clamping bolts - Axis distance: 180 mm - Clamping force: 4 x 12500 N - Repeatability: 0.005 mm - Axial load, max.: 4000 kg • Zero point clamping plate 320 x 320 - Automatic door Interface for automation and clamping systems Universal interface for automatic pallet changing systems, force clamping devices and zero point clamping systems • for pneumatic clamping systems • 2-channel rotary feedthrough integrated in the table • Pneumatic lines led to the outside • Pneumatic maintenance unit • Control via M commands logical inputs and outputs prepared incl. 7 pallets 320x320 with 6 vices and one 3-jaw chuck !!without tool holders and without tools!! Machine ex works, without delivery and assembly, all information without guarantee, price plus statutory value-added tax.

Condition: excellent (used), functionality: fully functional, LIMAS AB / VEB L-1048 & Type 6-76 | Line for slicing (dicing), washing, and weighing vegetables Manufacturer: Limas AB / VEB Maschinenfabrik Bad Gottleuba Model / Type: L-1048 complete with VEB Type 60 drum washer Serial number: L-10-8-01 (slicer) 1204 (VEB washer) Year of manufacture: 2008 (Limas slicer) Power supply: 380 V, 50 Hz VEB washer: power 1.1 kW, protection rating IP44 Hodpfx Anez Sfg De Nefn Line composition: - Limas AB potato slicer (type: 6x76) Serial number: L-10-8-01 Year of manufacture: 2008 Plastic (mesh) belt Belt width 850 mm Scraper height 50 mm Distance between scrapers 90 mm Plastic roller width 720 mm Cutting system consisting of 6 knives Distance between knives 115 mm Overall dimensions: 3150 x 1550 x 2370 mm. - Belt conveyor Plastic belt Belt width 520 mm Overall dimensions: 2080 x 800 x 980 mm. - Vertical screw conveyor Lifting height 1600 mm Overall dimensions: 1900 x 750 x 2900 mm. - Mobile VEB drum washer Type: 60 Serial number: 1204 Power supply: 380 V, 50 Hz Power 1.1 kW Protection rating IP44 Drum width 470 mm Perforation diameter 10 mm Overall dimensions: 1250 x 1100 x 1790 mm. - Weighing system: - Belt elevator with scrapers Belt width 350 mm / 220 mm Scraper height 50 mm Distance between scrapers 90 mm Lifting height 1700 mm - Systec industrial scale (type: IT3). Dimensions: 770 x 440 x 520 mm. Overall system dimensions: 3200 x 1000 x 2130 mm. This technological line is a fully automated, synchronized sequence of machines designed for the comprehensive preparation, slicing (dicing), intensive washing, and precise weighing of root vegetables, with particular emphasis on potatoes. The system finds wide application in food processing plants, large commercial kitchens, and vegetable processing facilities of the "marktfrisch" type. The technological process begins with feeding the raw material onto an elevating belt and a precision rotary-knife slicer from Limas, which, thanks to its 6-knife arrangement, ensures perfectly even cutting. Subsequently, the product is transported via conveyors and a vertical screw conveyor to a mobile VEB drum washer, where effective removal of impurities takes place in the drum with 10 mm perforations. The final element of the line is an integrated weighing system, which feeds the raw material directly onto a Systec IT3-controlled scale, guaranteeing full portion control and repeatability of the production process.

Condition: like new (used), Year of construction: 2020, operating hours: 1,500 h, functionality: fully functional, total width: 2,600 mm, total length: 3,700 mm, overall weight: 2,700 kg, type of input current: three-phase, input voltage: 6,000 V, input frequency: 50 Hz, pressure: 6 bar, Automatic glass cutting table for monolithic glass with loading-unloading arms. Main features: - Rectified rack-and-pinion transmission and linear guides with “0” clearance, ensuring high precision of movement on both axes. - Metal structure made of sheet metal profiles cut on a laser cutting machine and formed on a bending machine. The resulting structure has a minimum number of weld seams and, therefore, high dimensional accuracy and stability. - Latest generation, brushless electric motors, Lenze – Germany. - Automatic detection of glass thickness and automatic adjustment of the cutting head pressure to achieve maximum cutting quality. - The control panel can be located up to 7 meters away from the table. - Hydraulic folding of the loading-unloading arms. - The loading cycle is as follows: the extensions of the folding arms are manually pulled out, and the folding into the vertical plane is commanded. The glass is supported on the bases of the arms, and the folding is commanded. Hfjdpfxoz Rvi Eo An Nen After the glass reaches the horizontal plane, it is manually positioned by the operator anywhere in the cutting area. - Automatic detection of the glass position (automatic squaring) and automatic correction of the cutting head trajectory (the glass can be positioned anywhere on the surface of the cutting table). - “Double 0” system that allows mirror cutting of laminated glass with an accuracy of ± 0.5 mm. General feature: - The work surface of the Turomas tables is made of aluminum covered with a phenolic plate that is ground on one side, and a synthetic felt is glued on top. Since there are no wooden plates in the structure, there are no pressure losses in the air cushion. Also, due to the phenolic plate (a latest generation plastic), the work surface of the table is particularly resistant to mechanical impact, deformation, solvents, acids, humidity, and water vapor. - Intuitive TUR-ISO operator interface, easy to use, developed in a single window. The cutting plan can be viewed and edited in a field of this window. The Maintenance menu can also be accessed from this window, where all the set parameters of the machine can be viewed and modified. - Remote technical support system via the Internet for quick diagnosis and service. - Protection system with barriers and emergency stop button. - Scanner Scanning is done through a sequence of points, which are then converted into curves. The template thickness can be up to 20 mm. - VIN-CUT vinyl cutting - BRK 23 system - Consists of 1 transverse breaking bar + 1 longitudinal breaking bar (materialized by points). This breaking system guarantees minimal contact with the glass surface and maximizes the reduction of potential scratches due to the wear of traditional breaking bars (with a wooden contact surface). Automatic system for transferring the cut glass sheet from the cutting table to a breaking table. The system is mounted on the cutting bridge, on the opposite side of the cutting head, and consists of two vertical pistons that allow the glass to be moved to the next table. Cutting head with two cutting rollers. The table reads the glass thickness and automatically selects which of the cutting rollers to lower. By using this option, the entire range of glass thicknesses that can be cut is covered, in the range of 2 - 25 mm.