Used Edge Bending Machine for sale (85,053)

Condition: new, Year of construction: 2025, Pipe Bending Machine Zopf Model KB 100: Capacity: - Maximum pipe diameter: 100x5 mm (St. 37) - Square profiles: 80x80x3 mm - Solid material: 45 mm - Maximum tool diameter: 900 mm - Bending angle up to 210 degrees - Bending speed: 0 - 2.2 RPM - Motor: 11 kW, 400 Volt, 50 Hz, 3-phase - Weight: 1850 kg - Dimensions: 140x80x160 cm Features: - Digital display - Programmable bending angle - With foot pedal - Equipped with inverter - Powerful motor and reduction gearbox for high torque - Control unit for setting the bending angle - Counter for positioning the counter bearing - Mobile control panel - Quick tool change - All shafts hardened and ground - Manual material clamping Iodpjx I Afxjfx Agzsik - Worktable made of CK 45 steel

Year of construction: 2009, condition: good (used), KAL 210 with ZHR05 The machine is still built and can be demonstrated if needed. Iiodpfx Ajm Udzrjgzjk The machine is maintained and is still in use and produces a good quality. To be sold due to new acquisition. Available after arrangement. Further information gladly at any time. The machine is located in Nuremberg.

Year of construction: 2004, condition: used, 0-8 mm length 4.770 mm feed 11 m/min Iodpsn N H A Njfx Agzjik

Condition: excellent (used), Catalogue number 7843 TECHNICAL DATA - Table dimensions: 2050x350mm - Table dimensions with support: 2050x940mm - Min. workpiece length: 120mm - Min. workpiece width: 90mm - Workpiece thickness range: 10-45mm - Edge width range: 12-48mm - Edge thickness range: 0.4-3mm - Feed speed: 6.4m/min - Power consumption: 2.3kW - Required air pressure: 0.7 Mpa - Spindle speed: 10,000 rpm - Extraction connector: 2x100mm Isdpfxsx A Dt Do Agzsik - Heating power: 1250W - Dimensions (L/W/H): 2400x1300x1130mm - Weight: 360kg ADVANTAGES – Unpainted – With polisher – Used machine, in very good condition Net price: 12,000 PLN Net price: 2,860 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR (In case of significant exchange rate fluctuations, the price may change)

Year of construction: 2001, condition: ready for operation (used), General Data Machine weight 9200 kg Control Unit Brand AMADA Iedpfox D If Hsx Agzsik Main Drive Pressing force 200 kN Stroke 1350 mm Additional Equipment Next to the machine, there are 2 tool cabinets This AMADA Vipros 255 was manufactured in 2001. It is a used punching and bending machine, ideal for those looking to enhance their metal fabrication capabilities. Contact us for more information about this machine. Application Types Punching

Condition: good (used), Year of construction: 2003, machine/vehicle number: 02263, Offer 25492 Technical Data Iijdpfsx H R Rmsx Agzjk - Upper and lower rollers driven, each roller hydraulically adjustable - Suitable for prebending and conical rolling, side supports can be swung out - Operation via separate control panel with digital actual value display - Max. working width: 2050 mm - Max. sheet thickness at 400 N/mm² without prebending: 8 mm - Max. sheet thickness at 400 N/mm² with prebending: 6 mm - Bending capacity refers to at least 3 × top roller diameter - Hardened rollers - Top roller diameter: 190 mm - Side roller diameter: 170 mm - Bottom roller diameter: 140 mm - Drive: 400 V / 3.0 kW - Required space: approx. W 3500 x H 1300 x D 1300 mm - Weight: approx. 3200 kg

Condition: used, Technical details: bending angle max.: 0 - 225 ° operating voltage: 380 V Isdsx Adbnepfx Agzoik revolutions per minute: 5 -16 U/min Reinforcing Steel Bending Machine Perfekt 55 KA, PA, PLA — high-performance production machine. Thanks to the control system with four different bending speeds, the machine operates with exceptional efficiency. The bending angle is continuously adjustable from 0 to 225 degrees for left or right rotation. With its correction potentiometer for material spring-back compensation, the machine is ideal for medium and large-scale series production. Using the PA program control unit, up to eight different bending angles can be continuously pre-programmed from 0 to 225 degrees via rotary knobs. without accessories! *

Condition: good (used), Sumbel Perkeo Edge Gluer This machine is fully operational and ready for production. This is the most valued brand among small laminators. Ideal for the production of covers, decorative packaging, etc. Made in Germany. The machine uses cold glue. Copper rollers. Smooth adjustment: glue thickness and gap width. Iiedpfxjx A Sdqe Agzek Set of separators. Easy cleaning without the need for tools. 230V power supply. Weight: 15kg. Roller width: 60mm.

Condition: used, functionality: fully functional, Year of construction: 2013, Sahinler HPK 200 Hydaulic section and pipe bending machine Mil and Shaft Diameter: 200mm Tool and Roll Diameter: 900mm Working Speed: 2-5 m/min Motor Power: 30 kW Bending capacity x15x4 273x5.6 / 10000 mm Diameter biggest roll 9"x6,3 / 4000 mm Diameter top roll 650 mm Diameter upper roll 650 mm Roll capacity section - 3 200x200x18 / 5000 Shaft diameter 200 mm Top roll x15 with prebending min.120x120 / 3000 mm Voltage 3x400 V Iijdpfsw D Uqxjx Agzok Working speed 2-5 m/min Power Power max. 30000 W Height 2300 mm Length 2400 mm Width 3400 mm Weight15000 kg

Condition: used, Year of construction: 2023, New demonstration machine! List price €4,938 net. The robust Junior R1 offers all the features you would expect from a modern edge sanding machine. Its massive grey cast iron sanding unit with a powerful motor ensures maximum sanding performance. The work table, height-adjustable by spring pressure, allows for optimal belt use and safe operation. The upper section is made of heavy cast iron with an integrated three-phase motor (380 V, 2.2 kW, 2850 rpm). The machine is equipped with a built-in switch-plug combination, motor protection switch, and main switch compliant with VDE standards. Sanding belt back panel dimensions: 850 x 150 mm. Steel table height-adjustable by spring pressure. Belt size: 150 x 2280 mm. The sanding belt back panel is covered with a protective pad. The machine, when connected to a central extraction system with an air speed of at least 20 m/s, is dust-certified (GS). Includes angle and mitre fence. Technical data: • Motor power: 2.2 kW • Belt size: 150 × 2280 mm • Belt speed: 22 m/sec • Table size: 750 × 350 mm • Required space: 1000 × 800 mm • Weight: approx. 180 kg • Extraction connection Ø: 100 mm. Location: Rieth Iiedpfox Hwr Rox Agzsk

Condition: good (used), Year of construction: 1996, control type: CNC control, pipe diameter (max.): 28 mm, Tube diameter: 4-28 mm Wall thickness: / mm Minimum bending radius: 1.5 x D - 2.0 x D mm Control: Siemens LOGO Delivery rate: 4.5 l/min Max. bending angle +/-: 190° Iodpsx H R Hzjfx Agzsik Nominal pressure: 250 bar Operating pressure: 3095 bar Delivery rate: 4.5 l/min Total power requirement: 1.5 kW Drive: Hydraulic cylinder and roller chain

Condition: good (used), Year of construction: 2014, operating hours: 50,000 h, functionality: fully functional, machine/vehicle number: 2014.03.23, total length: 8,000 mm, total width: 2,200 mm, total height: 1,700 mm, type of input current: AC, input voltage: 400 V, space requirement length: 800 mm, power: 40 kW (54.38 HP), working width: 60 mm, product height (max.): 60 mm, 2 machines availible for narrow, longitudinal piece sanding construction: 3x left & 3x right - horisontal, paper sanding 360' vertical radius corner sanding Iiodpfxev T U A Us Agzjk 1x left & 1x right brushing speed approx 5m/min

Condition: new, tube diameter 33,7 x 3,4 GAS mm tube diameter 35,0 x 2,5 STAHL mm tube diameter 35,0 x 1,5 EDELST mm bending radius min. R10 - R 190 mm bending angle max. 0 - 180 ° tool taper 6-kant 40 mm voltage 230 V total power requirement 0,9 kW weight of the machine ca. 23,0 kg Description: - MediBender "070" digital - with maximum bending performance for 35 x 2.5 mm steel tubes - Excellent bending quality with very tight bending radii . (from 2 x tube diameter) and bending angles between 0° and 180° - Easy to operate - High accuracy and reliability Isdpfx Ajxab E Ssgzoik - Fast tool changes (within seconds) - Easy to transport - Huge selection of affordable standard tools (metric, gas inch, inch) BENDING SEGMENT AVAILABLE FOR AN ADDITIONAL CHARGE

Condition: excellent (used), Year of construction: 2005, Brandt KDF 530 C Edgebander with Jointing, Corner Rounding, Two Scraper Units, and Riepe Spraying Systems. A video of the machine in operation can be provided upon request. The machine is highly automated. Edge thickness: approx. 0.4 - 8 mm Workpiece height: approx. 10 - 50 mm Feed speed: approx. 11 m/min Soundproof hood Extendable workpiece support Extraction connections: 1x200 mm, 1x100 mm, including pictured ducting PC16 control system with color display for easy operation Units: Top pressure manual adjustment with SIKO counter Infeed fence manual adjustment with SIKO counter Riepe release agent spray system Ijdpfoxd Dudjx Agzeik Jointing cutter heads with Leitz Whispercut DIA cutters, resharpened Gluing unit switchable for synchronous and counter-rotation Pressure zone with 3 rollers Cross-cut saw with 2 motors, programmable for straight or beveled cuts Combination milling unit with motorized lateral adjustment Radius scraper R2 with pneumatic adjustment Corner rounding unit R2 with DIA cutter, 1 motorized, pneumatically adjustable for thin or thick edges Glue joint scraper pneumatically retractable, large roller Riepe cleaning agent spray system Buffing unit Hood lock CE mark Operating manual in folder and on CD All indexable inserts for the milling and scraper units have been replaced or rotated, saw blades and jointing cutters resharpened, buffing wheels replaced. The machine is therefore immediately ready for use. Only the DIA cutter of the contour milling unit has not been replaced, but it is still sharp. Minor paint touch-ups have been carried out. Approx. 3,500 operating hours. The condition of the machine speaks for itself. Occasionally, the PC reboots during operation (usually at high ambient temperatures), but this has not been an issue for us—you can continue working during the reboot. Machine dimensions approx. 4800 x 1200 x 1800 mm (L x W x H) Weight approx. 1,900 kg The machine can be inspected by appointment at our premises. We only offer machines that are ready for demonstration in our warehouse—see “more offers from this supplier.”

Condition: good (used), Year of construction: 1996, tube diameter 6 - 28 mm wall strength 2 mm bending radius min. 2 x D Control IPU 20 bending radius max. 5,0 x D mm Iedpfx Agovtgn Nszeik bending angle max. 190 ° arbor length 3000 mm operating pressure 180 bar hydraulic motor 4 kW weight of the machine ca. 900 kg dimensions of the machine ca. 3,8 x 1,1 x 1,3 m Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut. Mandrel lubrication, adjustable length stops. Operating modes: MANUAL and semi-automatic. Control buttons: hydraulics on / off, operating mode selection, clamp to / on, clamp forward / backward, mandrel forward / backward, bending forward / backward /, locking forward / backward, mandrel lubrication, turning device forward / backward, plate reset, length stop forward, emergency stop. The machine comes from a prototype construction and was only used a little until 2000. After that, the machines of this department were sold. However, the purchaser did not use the pipe bending machine and therefore it has only stood in the warehouse and has not worked since then ((original paint). Please notice that the price of a new machine today is over € 60.000,--. Machine dealer with own stock of 1600 m².

Condition: used, Year of construction: 2014, Feed direction of the panel: to the right from the operator Maximum edge thickness: 3 mm Minimum workpiece thickness: 8 mm Maximum workpiece thickness: 60 mm Iiodpow R Hirefx Agzjk Minimum workpiece width: 65 mm Minimum workpiece length: 160 mm Feed speed: 10 m/min Jointing unit: Yes, with 2 milling units Jointing tool: Diamond cutters Diameter: 70 mm Height: 48 mm Infeed fence adjustment: manual Chopping shear up to: 3 mm Single edge feeding: possible Gluing: GlueJet PU gluing: possible Cross-cut saw: Yes Combination unit for flush/bevel/radius: pneumatically adjustable Corner rounding unit: pneumatically adjustable Profile scraper: yes Flat scraper: yes Aggregate display: on the display Control type: via limit switches Operation: Control panel with buttons Transport device: No Extendable roller support: Yes Protective hood: Yes Working height or feed table height: 874 mm Weight approx.: 1400 kg Extraction diameter: 160 mm Storage location:

Condition: new, The Hydraulic Tube Bender 1/2 is a compact and mobile Tube Bending Machine designed for bending steel tubes of larger diameters with a powerful manual hydraulic pump. This machine boasts a capacity of 10 tons and comes complete with dies for commonly used tube dimensions, allowing you to create bends of up to 90 degrees. With its robust 3-leg stand and 6 bending segments, it ensures stability and ease of use during operation. The included attachments cater to various diameters, making this versatile tool ideal for your tube and profile processing needs. You can efficiently bend tubes while enjoying the benefits of its portable design. If you require a reliable Tube Bending Machine, consider the Hydraulic Tube Bender 1/2 from KNUTH to enhance your workshop capabilities. Don't hesitate to request a quote today! Iodjuzlh Ispfx Agzeik

Condition: as good as new (ex-display), Year of construction: 2022, functionality: fully functional, workpiece height (max.): 50 mm, edge thickness (max.): 3 mm, working height: 900 mm, space requirement height: 1,400 mm, space requirement length: 4,050 mm, space requirement width: 1,300 mm, operating pressure: 7 bar, with PLC control system (including touchscreen) and hot-melt adhesive application to the workpiece for edge materials up to 3 mm: joining cutter (including DIA tool), up to 2 mm cutting depth (max. 1 mm for special materials such as multiplex), maintenance-free glue pot with quick-change pot preparation including glue discharge device, HF trim saw station (approx. 12,000 rpm), HF milling station (approx. 12,000 rpm) with separate pneumatic adjustment and interchangeable cutter (combined version), corner round milling unit, surface scraper (including pneumatic lift), robust chain feed, ball-bearing double roller upper pressure, viewing window from machine rear side, extendable workpiece support, feed rate approx. 10 m/min. Complete with quick-change set-up for corner milling unit, radius scraper (including pneumatic lift), chassis F 4 – Technical Specifications Max. edge thickness: 3 mm Min. / Max. workpiece thickness: 8 – 50 mm Min. workpiece length: approx. 160 mm Feed speed: 7 m / min Ready for operation: approx. 3.5 min Max. power consumption: ∅ approx. 7.4 kW Electrical connection: 400 V / 3 Ph / 50 Hz Worktable height: approx. 900 mm Machine dimensions: approx. 4050 x 1300 x 1400 mm (L x W x H) Isdpfx Aox E N Nfjgzjik Weight: approx. 820 kg Extraction port: ∅ 1 x 140 mm

Condition: new, tube diameter 42.0 mm Stahl wall strength 3.0 mm Stahl tube diameter 54.0 mm CU/Alu bar material - diameter 30.0 mm wall strength 2.0 mm revolutions per minute 2.0 U/min voltage 230 Volt total power requirement 1.1 kW weight 80.0 kg range L-W-H 410 x 1000 x 570 mm ERCOLINA MediBender "MB 42 M" Iodpfxoxaa Sds Agzeik - Capacity steel pipe 42 x 3.0mm - Capacity gas pipe 1“1/4 gas x 3.5 mm - Capacity square profile (FE 42) 35 x 35 x 3 mm - Max. bending radius 10-260 mm - Minimum radius 2 x D - 6-edge tool holder - Min. outside diameter 5 mm - 1/8“ gas Equipment: - patented fast tool change system - one bending speed - freely movable foot switch - bending tools on request for an additional charge including ERCOLINA microprocessor control: - with 30 programs each program with up to 9 bending angles programmable - in addition, the necessary correction angles can be entered . for each bending angle in the working mode BENDING SEGMENT AVAILABLE FOR AN ADDITIONAL CHARGE

Condition: good (used), functionality: fully functional, Year of construction: 2025, machine/vehicle number: 0100-0149-2024, overall weight: 700 kg, total length: 3,500 mm, total width: 1,100 mm, total height: 1,500 mm, TECHNICAL DATA & EQUIPMENT: Suitable for flat material Working length: approx. 2500 mm Iodpfexm Symjx Agzsik PICK-UP NOTES: Collection must take place strictly between December 10th and 12th FCA Winterlingen, loaded onto truck

Condition: good (used), Year of construction: 2021, 0,4 - 3 mm Workingpiece thickness from to 10 - 50 mm Ijdpfjxzuxhex Agzjik Feed speed 9 m/min m/min.

Condition: used, Year of construction: 2016, Plate feed direction: from operator to the left Max. edge thickness: 2 mm Min. workpiece thickness: 10 mm Max. workpiece thickness: 40 mm Min. workpiece length: 180 mm Feed speed: 7 m/min Heating time: 4 min Jointing unit: Yes, with 2 milling units Jointing tool: diamond cutter Diameter: 70 mm Iisdpfjx Hwq Tex Agzok Height: 43 mm Adjustment of infeed fence: diamond cutter Cut-off shear up to: 2 mm Individual edge feeding: possible Gluing: glue contact roller Cut-off saw: Yes Combination flush/chamfer/radius unit: pneumatically adjustable Scraper: Yes, scanning Display of units: on the display Control type: PLC line control Operation: touch screen Motor power: 7.4 kW Travel device: Yes Extendable roller support: Yes Protective hood: Yes Weight approx.: 750 kg Extraction connection diameter: 140 mm Electrical connection: 400 Volt/50Hz Storage location: Customer

Condition: new, The KF 200 is a robust Edge Beveling Machine from KNUTH, designed for efficient chamfering, deburring, and 45° beveling of steel, aluminum, and a variety of other materials. Its compact dimensions and simple operation make it particularly well-suited for large workpieces, including heavy metal sheets and long profiles. With tungsten alloy blades, the KF 200 offers superior tensile strength, hardness, and longevity, ensuring that demanding tasks are executed with precision. This machine operates at a speed of 3,500 revolutions per minute and can achieve chamfer heights ranging from 0 to 5 mm, making it versatile for different applications. Standard equipment includes a set of cutting inserts and an operator manual, allowing you to start working immediately. Whether you're preparing weld joints or performing intricate deburring tasks, the KF 200 stands out in the Edge Beveling Machines category. To enhance your production capabilities, request a quote today and elevate your sheet metal processing with KNUTH. Iedeq Ny R Sspfx Agzeik

Condition: used, Year of construction: 2024, New demonstration machine! List price: €4,938 net. The upper section is a heavy-duty cast iron design with an integrated three-phase motor, 380 V, 2.2 kW, 2850 rpm. The machine is equipped with an integrated switch-plug combination, motor protection switch, and main switch compliant with VDE standards. Dimensions of the sanding belt backing: 850 x 150 mm. The steel work table height is adjustable via spring tension. Belt dimensions: 150 x 2280 mm. The sanding belt backing is covered with a graphite slip lining. The machine is supplied with an assortment of sanding belts; also included in the scope of delivery are an angle and miter gauge. When connected to a central extraction system, the machine is dust-tested (GS) by Holz-BG Stuttgart for an airspeed of at least 20 m/s. Standard equipment includes: - tiltable 90-180°, - motorized belt oscillation, - small support table at the deflection roller, - pneumatic belt tensioning. Technical data: Motor power: 2.2 kW. Sanding belt size: 150 x 2280 mm. Sanding belt speed: 22 m/s. Table size: 750 x 350 mm. Space requirement: 1000 x 800 mm. Weight: from 180 kg. Extraction connection Ø: 100 mm. Storage location: Rieth. Iedpfxsx Hwpvo Agzjik

Condition: used, Year of construction: 2024, New showroom machine! List price: €10,643 net. The model for enhanced comfort. The RS-2010 edge sanding machine, with its versatile features, provides complete processing in edge sanding. Quick switching between freehand and veneer edge sanding, belt oscillation, and continuously adjustable sanding unit tilt allow for universal machining. The height-adjustable pneumatic support table and pneumatic belt tensioning ensure easy handling. Iiodpfxsx Hwppe Agzsk Technical features: - Pneumatically height-adjustable work table - Continuously adjustable sanding unit tilt up to 45° - Simple conversion to veneer edge sanding - Pneumatic belt tensioning - 0 - 45° display for sanding unit - Stable support table at the return roller - Feed console - Angle and mitre fence Technical data: Motor power: 3 kW Belt speed: 22 m/s Belt length: 2,760 mm Belt width: 200 mm Table size: 450 x 920 mm Required space: 1,200 x 2,000 mm Extraction (dust collection): 120 & 80 mm Total weight: approx. 500 kg + 5 years warranty on all our products (except wear parts)! Stock location: Rieth