Used Feed Apparatus for sale (11,296)

Condition: used, Frame die-cutter - Swivel frame die-cutter - Flatbed die-cutter - Platen die-cutter - Eccentric press Punch + feed for the use of bandknife punching tools Flatbed die cutter HELMERDING type PSH 25 Com. No. EP 97784 Machine. No. 6073 Year of construction 1998 Compressive force 25 ton. Clearance between the tie rods 700 mm Table surface = installation space 800 x 670 mm Table surface = installation frame width 510 x depth 440 mm, plate thickness 20 mm Plunger surface 800 x 670 mm Hole in the table 490 x 420 mm Plunger stroke 45 mm Ram adjustment travel 10 mm Installation height = tool height 100 mm Stroke rate up to 250 strokes/min. Motor power 15 kW Mains connection 400 Volt, 50 Hz - Controlled drive for infinitely variable stroke rate - Pneumatic clutch-brake combination - ram compensation cylinder Duedpedzqmzofx Abhep - VOGEL automatic central lubrication system - solid base plate with 4 swinging elements under the machine Space requirement L x W x H approx. 3000 x 2000 x 3000 mm Weight 4.5 tons good condition The machine was formerly used for cutting out cardboard blanks. Ideal for cutting out non-woven fabrics or similar for breathing masks.

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. Djdpfx Asdzqltebhoup - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Feeding technology / Feeding system / Vibratory feeder / Sorting unit / Bowl feeder Vibratory bowl, sorting device / Screw feeding with vibratory feeder for screw technology Feeding system DEPRAG Type: 0611-P/0.75-1S No.: 1183885 Year: 2011 - 2012 The system was used for feeding electrical connector pins. Product dimensions: Ø 4 mm, length 39 mm The pins are preloaded in the material hopper; the feed belt conveys the pins as required into the bowl feeder. From the bowl feeder, the product is transferred via the linear feeder to the product inverter. The product inverter orients the product into the correct position and makes it available for further processing. The unit comes from a prototype system; the external electrical control unit is not present and should be replaced by a PLC. Without modification, for example, suitable for the automatic and properly oriented feeding of threaded pins up to M4 x 40. The unit consists of the following components: 1 piece belt hopper / feed conveyor DEPRAG Type: B 10 Serial no.: 1178201 Order no.: 415050A Year: 2011 Dujdpekpwuujfx Abhop Fill volume: 10 liters Belt speed: 100 mm/min. Operating voltage: 24 V (DC) - Belt surface dimpled - Foldable stainless steel chute Weight 11 kg 1 piece bowl feeder KENDRION Type: OA C006.504101 / OA C006029 / KQF 465 B5 Bowl diameter (top): 200 mm Bowl diameter (bottom): 100 mm Bowl internal height: approx. 75 mm Sorting track width: approx. 5 to 8 mm Operating voltage: 230 V, 50 Hz. 1 piece DEPRAG vibratory controller for the bowl feeder Type: SZG Controller 6 Serial no: 35 pieces linear feeder KENDRION Type: WS3B/36 Part no: WSB003,564025 Operating voltage: 230 V, 50 Hz. 1 piece DEPRAG vibratory controller for the linear feeder Type: SZG Controller 6 Serial no: 35 pieces product inverter FESTO with 180° swivel range - 1 piece FESTO valve block CPV10-VI 18200 - Compressed air requirement approx. 6 bar - 1 piece MURR base module type MVP12 - Complete unit mounted on a steel plate with 4 support legs Space requirements (L x W x H): 1150 x 520 x 860 mm Weight: 100 kg Very good condition

Condition: used, Straightening machine, strip straightening device with adjustable LENZE geared motor Straightening machine, strip tensioner was used for cardboard approx. 350 x 1.5 mm Not suitable for use as a classical straightening machine Type 11.712.02.10 Output speed of geared motor: 12 to 72 rpm, stepless Torque: 80 to 40 Nm Straightening roller speed: 19 to 115 rpm Straightening roller width: 520 mm Straightening roller diameter: 90 mm Total number of straightening rollers: 4 pcs Motor power: 0.37 kW Power supply: 380 Volt, 50 Hz Dodpfxodzp U Ae Abhsup - Pull roller pair, drive of the lower rubber-coated roller via open gear drive - Speed infinitely adjustable via handwheel on the geared motor - Upper part of the straightening rollers mechanically adjustable - Straightening unit with 3 rollers, one of the rollers is missing (rollers of the straightening unit not driven) - On a sturdy metal base - Straightening machine was used for cardboard approx. 350 x 1.5 mm Space requirement (L x W x H): 630 x 460 x 1060 mm Weight: approx. 160 kg Good condition

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 31620 € 603.94 € 0.4 - 2 mm 600 mm 1200 mm² 80 mm 75 m/min 10 m/s² 10 Nm helical gear boxWATTDRIVE (Made in Austria) FESTO pneumatic equipment servo drive and control SIEMENS Dedoynnf Nopfx Abhsup 7" colour touchscreen SIEMENS 2 driven rolls OPTIONAL EQUIPMENT Handrwheel and Simlinx remote control € 4.290,--

Condition: new, neu Dsdpfeynnf Aox Abhoup ca. 8 Wochen ab Auftragse Türkei 31080 € 593.63 € 0.4 - 3 mm 400 mm 1200 mm² 80 mm 75 m/min 10 m/s² 10 Nm helical gear boxWATTDRIVE (Made in Austria) FESTO pneumatic equipment servo drive and control SIEMENS 7" colour touchscreen SIEMENS 2 driven rolls OPTIONAL EQUIPMENT Handrwheel and Simlinx remote control € 4.290,--

Condition: new, neu ca. 8 Wochen ab Auftragse Türkei 28390 € 542.25 € 0.4 - 3 mm 300 mm 900 mm² 80 mm 75 m/min 10 m/s² 10 Nm helical gear boxWATTDRIVE (Made in Austria) FESTO pneumatic equipment servo drive and control SIEMENS 7" colour touchscreen SIEMENS Dusdpfx Abjynnfvshop 2 driven rolls OPTIONAL EQUIPMENT Handrwheel and Simlinx remote control € 4.290,--

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei 13760 € 264.19 € 0.4 - 2 mm 400 mm 300 mm² Dodpfeynncnox Abheup 63 mm 150 m/min 10 m/s² FESTO pneumatic system SIEMENS servo drive and control system 7’ colour touch screen SIEMENS 2 feed rollers Option: Handwheel and Simlinx remote maintenance module € 4.290,--

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei 12950 € 248.64 € 0.4 - 2 mm 300 mm 300 mm² 63 mm 150 m/min 10 m/s² FESTO pneumatic system SIEMENS servo drive and control system Dujdpfx Aboynnchshep 7’ colour touch screen SIEMENS 2 feed rollers Option: Handwheel and Simlinx remote maintenance module € 4.290,--

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei 12630 € 242.5 € 0.4 - 2 mm 200 mm 300 mm² 63 mm 150 m/min 10 m/s² FESTO pneumatic system SIEMENS servo drive and control system 7’ colour touch screen SIEMENS 2 feed rollers Dodsynncbopfx Abhsup Option: Handwheel and Simlinx remote maintenance module € 4.290,--

Condition: good (used), Chuck flange, flange mount, chuck flange, drive flange, intermediate flange, chuck faceplate, mounting flange Duodoykpt Tjpfx Abhop -Muck flange: Mounting flange for three-jaw chucks, four-jaw chucks, faceplates -Outer diameter: 162 mm -Socket: Short cone 5, cone Ø 79 - 82 mm -Hole circle: Ø 105 x 10 mm / Ø 62 mm M10 -Passage: Ø 41 mm -Dimensions: Ø 162 x 48 mm -Weight: 4.7 kg

Condition: used, material width 45 mm material thickness 45 mm feed length 100 mm compressed air 6 bar clamping force of fastening pincer 25000 N Duedpfx Abeylzzlehep clamping force of moving pincer 15000 N feeding force 10000 N weight 0,1 t Dimensions (WxDxH) 0,6 x 1,0 x 1,0 m SPECIAL DEAL as is where is WITHOUT putting into operation / WITHOUT additional work free loaded to truck hydraulic pincer feed - with special clamping jaws for profiles

Condition: used, material width 200 mm material thickness - 6,0 mm feed length 0 - 120 mm Dodpfx Abovuuntehsup Weight 0,40 t required space 0,9 x 0,8 x 0,7 m SPECIAL DEAL as is where is, WITHOUT putting into operation, in given condition mechanical roll feed drive via main shaft / pivot shaft of the press - pivot shaft / mounting plate not included max. no. of strokes approx. 1500 / min

Condition: reconditioned (used), Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Dodpoyizxrofx Abheup Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Replacement of all plastic sliding plates for the hydraulic push floor. Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. All six limit switches (proximity sensors) on the push floor were replaced. The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2026, Dimensions (L/W/H) 1400x2450x2800 mm Total pressure 400 to weight of the machine ca. 12000 kg Dedpfxoyk H Twj Abheup

Condition: new, Year of construction: 2025, feed 2-22 m/min Weight 60 kg Dujdpfsvz E Ukjx Abhop Total power requirement 0,4 kw

Condition: ready for operation (used), functionality: fully functional, Auction of a Joulin vacuum lifter with stacking function and infeed! The vacuum lifter is only 1.5 - 2 years old! The machine can be used as a standalone unit or as part of a complete line: - Bandsaw Canali ML 1100 TWIN F.L. 30 H.S. (Search ID: 21264817) - Wide planing machine Costa Planing Machine (Search ID: 21264937) TECHNICAL DETAILS Load capacity per layer: 300 kg MACHINE DETAILS Vacuum suction length: 6,000 mm Vacuum suction width: 1,400 mm Dedpfx Abjyk Tifsheup

Condition: excellent (used), Catalogue number 7670 TECHNICAL DATA - Track width: 340 mm - Roller width: 400 mm - Max. blade diameter for multi-blade saw: 350 mm - Blade bore diameter: 80 mm - Max. cutting height for edger: 100 mm - Max. cutting height for multi-blade saw: 120 mm - Table width with clearance: 900 mm - Table length: 1780 mm Djdpfx Absyk E Hpsheup - From above: - Kickback fingers - Pressure roller, sliding, metal - Kickback fingers - Pressure roller, sliding - Saw shaft with blades - Pressure roller, sliding - Sliding pressure shaft, metal - From below: - Guide bar - Kickback fingers - Track - Central lubrication - Stepless feed speed adjustment - Electric lifting of saw shaft 0.75 kW + body 1.1 kW - Feed motor 1.5 kW - Main motor 22 kW - Floating saw movement 0.55 kW - Lasers (not working, require inspection) - Extraction port diameter: 210 mm - Overall dimensions (L/W/H): 2200 x 1450 x 2000 mm - Weight: 1925 kg ADVANTAGES – Made in Germany – Shaft with floating blade for edging – Additional sleeve for multi-blade saw included – Used multi-blade saw, in very good condition Net price: 58,900 PLN Net price: 14,030 EUR (based on exchange rate 4.2 EUR) (Prices may change with larger fluctuations)

Condition: new, functionality: fully functional, Year of construction: 2025, The wobbler feeder is a feeding system that delivers superior performance, especially when handling large, sticky, and moist materials. Its structure, consisting of rotating elliptical rods, creates a vibrating motion during material flow. This motion separates fine materials from larger particles and provides consistent feeding to crushers and screens. As a result, clogging is prevented and the overall efficiency of the plant is increased. Widely used in the mining, aggregate, and recycling industries, wobbler feeders are typically placed in front of primary crushers. This ensures that the material undergoes pre-screening in the initial stage. Its ability to operate without clogging, even with sticky and clayey materials, makes it an ideal solution for demanding conditions. Its mechanically simple design, ease of maintenance, and long-lasting performance keep operating costs to a minimum. With these features, wobbler feeders are a reliable choice for all plants requiring a continuous and balanced material flow. Wobbler Feeder Technical Specifications Body Liners: HARDOX 450 – 10 mm Feeding Capacity: 150 - 200 t/h Weight: 18.5 tons Dimensions: 4,000 x 1,000 mm Wobbler Motor: 14 x 3 kW, 1500 rpm, GAMAK brand Gearbox: Heavy-duty type Walking Platforms: Available Steel Feet: Available Why Choose CONSTMACH Wobbler Feeders? Duodpfxoxpvh Te Abhop CONSTMACH wobbler feeders stand out with their high-quality, durable materials, heavy-duty gearboxes, and ease of maintenance. Each one is designed to offer long-lasting, low-cost operation. HARDOX body liners provide maximum resistance to wear, while the adjustable design easily adapts to different material types. CONSTMACH is a trusted name in the industry for its production quality, engineering support, and after-sales service. Invest in a wobbler feeder with the CONSTMACH guarantee for the continuity and performance of your facility. What Do We Do at Constmach? Constmach is a leading machine manufacturer offering a wide range of products designed to meet the needs of the construction and mining industries. Our product portfolio includes concrete block making machines, stationary and mobile concrete plants, stone crushing machines, stone crushing and screening plants, sand washing machines, sand making machines, asphalt plants, conveyor belt systems, jaw crushers, and mobile crushing plants. With its high quality standards, innovative production approach, and customer-focused solutions, Constmach stands out as a reliable brand in both national and international markets. Our products continue to be the preferred choice of industry professionals due to their durability, efficiency, and long-lasting performance.

Year of construction: 2005, condition: used, Apple engineering MM975 Mini Force Feed Depositor Stainless mobile height adjustable single head pneumatic depositor with variable speed scroll feeder in hopper for positive product feeding Djdpob Ucqlefx Abhjup

Year of construction: 2000, condition: repair required (used), Feed transport equipment consisting of Dodpfedi Nykox Abhoup 1 piece conveyor belt and 1 piece roller conveyor ideal for (A) before planing machine with much hand saw (B) before cutting band saw or other saw (C) at the inlet before other machines in the state as is and without electrical control

Condition: like new (used), Chain feed table, used for feeding and linear transportation of roll goods or log goods. Djdpfx Abotw Sm Njhjup Forward/reverse run (reversing circuit) integrated, end positions are queried via roller limit switches. Feeding length: 2200mm Feeding height: 950mm (adjustable) Drive power: 0.18kW (Getriebebau Nord) Condition: slight paint wear, otherwise as good as new

Condition: new, Shaft diameter: 580working speed: 3-6motor power: 30length: 2760width: 2310heigth: 2680weight approx.: 14400 Technical specifications: Dusdjh Alh Hspfx Abhsp Welded steel construction frame 3 rollers are driven Hardened and ground shafts made of high-strength special steel Rollers are hardened and ground Horizontal and vertical working position Hardened standard rollers Mobile control panel Angular side guide rollers Brake motor equipped for precision bending Digital displays (2 pieces) Options: Digital display STANDARD NC unit 10 screen EURO 11,500.00

Condition: used, functionality: fully functional, Year of construction: 2017, 1x Mixer Holding Tank / Storage Container - Custom-made from V4A stainless steel - Used in our pellet production line as a buffer tank for herbal mixtures in powder form. It features a feed line (right side) from the mixer and a discharge on the left side to the intermediate storage tank. At the inlet from the mixer, there is also an option to divert the mixture into big bags prior to storage. - Material feed via electric auger (top) - Material discharge via electric auger (angled) Dodpjxtmxwefx Abheup Filling capacity naturally varies depending on the type and volume of the mixture. With our mixtures, it held approximately 2 x 400 kg. All motors and sensors are fully functional.

Condition: excellent (used), CATALOG NO. 6916 TECHNICAL SPECIFICATIONS - Maximum workpiece width: 200 mm - Maximum workpiece height: 150 mm - 2 sanding units: Upper: steel roller + pad + steel roller Lower: steel roller + pad + steel roller From above: - Pressure roller, steel - Sanding unit - Sliding pressure roller, steel - Cleaning brush - Feed belt From below: - Feed belt Dodpjx Swtxofx Abhsup - 2 smooth sliding steel rollers - Sanding unit - Pressure roller, steel - Cleaning brush - Discharge roller - Electrically adjustable sanding height - Pneumatic oscillation of sanding belts - Infinitely variable feed speed regulation - Feed motor: 0.55 kW - Main motors: 2 x 4 kW - Air requirement: 6-8 bar - Extraction ports diameter: 3 x 80 mm, 1 x 120 mm - Overall dimensions (L/W/H): 1800 x 2070 x 2000 mm - Weight: 1422 kg – German manufacture, – unpainted – Very good condition, – used sander Net price: 25,900 PLN Net price: 6,160 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR (price may change in case of significant exchange rate fluctuations)