Used Friction Press for sale (12,496)

Condition: used, Technical details: pressure: 160 t throat: 760 mm slide stroke: 32...140 mm Bdodpfxeu Nfhqo Abwec distance between table / ram: 400 mm ram adjustment: 100 mm no. of strokes: 50 Hub/min table:: 760x1000x95 passage opening in table: 400x350 mm clamping surface ram: 630x850 mm clamping plate: 760x1010x92 mm total power requirement: 15 kW weight of the machine ca.: 6,2 t dimension machine xH: 2,9x1,2x3,4 m dimensions electric cabinet LxWxH: 0,8x0,45x2,1 m - via two hand control - copy of documents digital available Machine can be demonstrated under power. *

Condition: used, Technical details: pressure: 80 t dayligth: 600 mm ram stroke: 200 mm pressure: 30 t dayligth: 680 mm Bdjdpfx Aeu Nfnwobwsc ram stroke: 300 mm distance between columns: 1060 mm base plate surface area: 1060x600 mm table above floor: 720 mm ram stroke speed: Stößel/ Ram 1: 40 mm/sec ram stroke speed: Stößel/ Ram 2: 95 mm/sec base plate surface area: Dm=150 mm total power requirement: 13 kW weight of the machine ca.: 4,5 t space requirement approx.:: L:1,6xB:1,1xH:3,4 m - Press with two ram with 30 t + 80 t - foot control - documentation *

Condition: used, Year of construction: 1991, Technical details: pressure: 40 t daylight dimension : table/slide up: 450 mm throat: 375 mm ram stroke: max. 300 mm Table dimensions: 900 x 500 x 85 mm passage inside table: Ø 120 mm height over floor: 900 mm total power requirement: 15,0 kW weight of the machine ca.: 5,8 t Bedpfx Aju Nfp Iebwedc dimension machine xH: 2,3 x 1,45 x 2,40 m further technical data: -size of the ram plate W: 900 x D: 500mm -pivot hole in ram Ø 40 x 75mm -Hydraulics: tank capacity approx. 500Liter; operating pressure 275 bar; pump capacity 22,9 l/min. Two-hand operation and/or control panel *

Condition: used, Year of construction: 1960, Technical details: pressure: 10 t Bodpeu Nfudsfx Abwedc throat: 255 mm max. ram stroke: 400 mm ram speed - reverse: 0,180 m/sec. m/sec. ram speed - forward: 0,080 m/sec. m/sec daylight dimension : table/slide up: 630 mm daylight dimension : table/slide low: 230 mm table clamping surface:: 420 x 400 mm passage opening in table: 220 mm surface area of ram: 200 x 200 x 65 mm total power requirement: 1,6 kW weight of the machine ca.: 1,1 t dimension machine xH: 1,1 x 0,5 x 2,1 m

Condition: used, Technical details: Bodpou Icw Hofx Abwodc punching cross section in mm²: 45 kp/mm² table-size: 120x100 mm throat: 80 mm weight of the machine ca.: 15 kg space requirements of the machine approx.: 0,3x0,2x0,95 m Punching Press *

Condition: used, Technical details: pressure: 100 t daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm ram speed - forward: 200 m/s ram speed - reverse: 200 m/s Table dimensions: 750 x 560 x 90 mm passage inside table: Ø 26 mm clamping surface ram: BxT: 530 x 400 mm mortise hole in ram: Ø 50 mm cylinder diameter: Ø 250 mm height over floor: 720 mm total power requirement: 17,0 kW Bdedpfx Absvc Ax Nowec weight of the machine ca.: 5,5 t dimension machine xH: 1,8 x 1,2 x 3,2 m

Condition: used, Technical details: pressure: 80 t distance between columns: 880 mm dayligth: 200 mm Table dimensions: 880x300 mm height over floor: 1000 mm distance between columns: 800 mm total power requirement: ca. 12 kW machine weight ab.: 2855 kg space requirements of the machine approx.: T:1,4xB:1,65xH:1,9 m Embossing - Hot Embossing application area: - for example: for foils, plastics, paper, hardboard materials etc. - stamp plate size: 600x310mm equipment: - counter - hydr. tank Accessories: - Mounting plate (600x300x90mm) not heatable. Sale as is. Bodpfx Abou Icwtewjdc *

Condition: new, Year of construction: 2025, pressure 1000 t distance between columns 4250 mm Bjdpfx Asym D E Aebwodc stroke 400 mm Control SIEMENS S7-1500F table dimension - longitudinal 4000 mm table dimension - cross 1600 mm total power requirement 200 kW weight of the machine ca. 250 t dimensions of the machine ca. 7,5 x 4,8 x 7,4 m

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, power: 17 kW (23.11 HP), pressing force: 220 t, stroke length: 180 mm, throat depth: 420 mm, total width: 3,650 mm, total height: 2,900 mm, overall weight: 17,900 kg, Hydraulic press brake Manufacturer: AMADA, Type: HFB 220-30 H Year of manufacture: 1991 Technical data Manufacturer: AMADA Type: HFB 220-30 H Year of manufacture: 1991 Press force: 220 tons Bending length: 3100 mm Stroke: max. 180 mm Overhang: 420 mm Distance between side supports: 2750 mm Power: 17 kW Dimensions: L 3,65 m, W 1700 mm, H 2900 mm Weight: 12.9 t Equipment Bjdpfoy T R Ryox Abwedc • Delem DA 58 2-D graphics control system • Controlled axes: Y1, Y2, X, R1, R2, Z • Large tool package, see photos • Amada quick-release tool clamping system All information is provided without warranty. A live demonstration is possible at any time in our showroom.

Condition: good (used), Year of construction: 2005, functionality: fully functional, pressing force: 50 t, stroke length: 215 mm, Hydraulic press brake Manufacturer: TRUMPF, Type: TrumaBend V500 Year of manufacture: 2005 Technical data Manufacturer: Trumpf Type: TrumaBend V500 Year of manufacture: 2005 Capacity: 50 t Working length: 1250 mm Stroke: 215 mm Bdsdsy T Hx Topfx Abwsc Distance between uprights: 1040 mm C-frame overhang: 420 mm Installation height: max. 385 mm Working speed: 10 mm/s Return stroke speed: 220 mm/s Voltage: 3 x 400V Rated current: 21.5 A Connected power: 8.6 kVA Compressed air connection: 6 bar Dimensions: approx. L 2.00 x W 2.00 x H 2.40 m Weight: 4.9 t Equipment • Trumpf TASC 6000 control system • Pneumatic die shifting • Hydraulic tool clamping, top and bottom, Wila/Trumpf • Controlled axes: Y1, Y2, X, R, Z1, Z2 • Bend-Guard safety light curtain, front • Tool package: - Upper tool 202/K, straight, R1, H 120mm, L = 1,250mm, segmented - Lower tool EV/S W6/84°, L = 1,225mm, segmented - Lower tool EV005, W16/30°, L = 1,090mm, segmented - Lower tool V24/80°, L = 1,120mm, segmented All information is without guarantee. A live demonstration is possible at any time in our showroom.

Condition: used, Year of construction: 2001, operating hours: 2,500 h, total length: 3,540 mm, total width: 1,500 mm, total height: 2,330 mm, Colour: Grey Weight: 8.230 kg - Year: 2001 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 5356 - Operating hours: 2500 - Drive system: Conventional Bsdey Thmxjpfx Abwjdc - Power [kW]: 11.0 - Press force [ton]: 160 - Max. working width [mm]: 3100 - Column gap [mm]: 2500 - Backgauge depth [mm]: 750 - Max. stroke [mm]: 200 - Tools included: Yes - Transport dimensions: 3540mm x 1500mm x 2330mm (l x w x h) - Transport weight [kg]: 8230kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1973, pressure 28 t distance between columns 510 mm dayligth 380 mm stroke 260 mm weight of the machine ca. ca. 750 kg Bjdjv Svc Tspfx Abwedc

Condition: good (used), Baling press, Schleicher, 16 S – used - : Ex-works price: only €1,950 (net) Manufacturer: Schleicher Model: 16 S Serial number: 6150I1730E Year of manufacture: 20 Height: 2000mm / Width: 1500mm / Depth: 900mm Weight: 1,850kg 380V, 3-phase, 10.3 AMP, 4kW Condition: good Available: immediately Location: Husum Bdjdpoyzcwhsfx Abwec Operating manual not available.

Condition: good (used), Year of construction: 2008, pressing force: 30 t, Baler presses, Bramidan, 4-x 30 SLD, 30 tons pressing force – used - : Price ex location: only €3,950 (net) Bodpeyzcvwjfx Abwodc Manufacturer: Bramidan Model: 4-x 30 SLD Number: PEY297206-3 Year of manufacture: 2008 H: 2300mm / W: 1800mm / D: 1500mm Weight: 1,850kg 3x230/400V, 25/16 Amp, 4kW Condition: good (the photo with the warning tape is simply to indicate that the press is not being used anymore as a new, larger one has been purchased) Available: immediately Location: Husum Operating manual available

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Bodpfjy S Rqwex Abwsdc Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: like new (used), Year of construction: 2017, functionality: fully functional, operating hours: 4,500 h, Hydraulic press brake Manufacturer: TRUMPF, Type: TruBend 3066 B26 Year of manufacture: 2017 Like new, only 4,500 operating hours! Technical data Manufacturer: TRUMPF Bdodpsy Txdbofx Abwoc Type: TruBend 3066 (B26) Year of manufacture: 2017 Bending length: 2040 mm Press force: 66 t Operating hours: 4,500 h (metered) Free clearance between uprights: 2364 mm Reach: 400 mm Stroke: 200 mm Y-axis rapid traverse speed: max. 200 mm/s Y-axis working speed: max. 15 mm/s Drive power: 17 kW Dimensions: L 2.60 x W 1.65 x H 2.40 m Weight: 5650 kg Equipment - Electro-hydraulic upper drive - Block hydraulics - Controlled axes: Y1, Y2, X, R - 3 backstops - TRUMPF upper and lower tool clamping system - Self-adjusting crowning system - Control: Delem T3500T Multi-Touchscreen 17" - Light curtain front BendGuard - Integrated TRUMPF technology data - Foot switch - Technical documentation - Tool package consists of: - Upper tool Trumpf OW201K, slightly bent, 86°, L = 1,250 mm, segmented - Bent upper tool, H 120 mm, R1/86°, L = 1,950 mm, segmented - Lower tool EV042, V10, L = 1,250 mm, segmented - Lower tool V24, 80°, L = 2,000 mm - plus various short tools All information without guarantee. A demonstration under power is possible at any time in our showroom.

Condition: ready for operation (used), Year of construction: 2002, Very well-maintained, used press brake from Darley. Type: EHP LS 230 43 37 Capacity: 4300 x 230 tons Delem DA 66W CNC control Bodpfx Aey Szikjbwsdc CNC crowning Y1, Y2, X1, X2, R1, R2, Z1, and Z2 axes CNC controlled Hydraulic Wila New Standard top and bottom clamping Includes 1 set of tooling as shown in the picture.

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, operating hours: 15,396 h, pressing force: 173 t, stroke length: 500 mm, overall weight: 16,000 kg, working length: 4,250 mm, Equipment: CE marking, full service history, Due to a technical malfunction, bidding was occasionally impossible – therefore, a new auction! TRUMPF TruBend 5170 including BendMaster! The machine has been continuously serviced and maintained by TRUMPF, with a complete service record. The cylinders are leak-proof and have no oil loss. The tools shown for the robot are included. TECHNICAL DETAILS Stroke: 500 mm Press force: 1,700 kN Working length: 4,250 mm Bedoy T I E Ispfx Abwjdc Tool clamping: Hydraulic, top and bottom Number of axes: 6 Load capacity: 60 kg MACHINE DETAILS Voltage: 3 x 400 V Rated current: 41.0 A Frequency: 50 Hz Connection power: 28.0 kVA Control voltage: 24 V DC Follow-up time: max. 90 ms Follow-up distance at 220 mm/s: max. 10 mm Follow-up distance at 160 mm/s: max. 8.5 mm Operating pressure: max. 300 bar Weight: 16,000 kg Operating hours Operating time of press beam: 15,396 h Operating time of hydraulics: 83,212 h Machine operating hours: 152,638 h EQUIPMENT CE marking Documentation/Manual Rear stop with sensors CNC crowning Bendmaster (robot, 8 m travel path) Vacuum manipulators CNC gripping station Double sheet detection Safety device BendGuard Lasersafe Spare parts: cable track, replacement vacuum plate, BWF fixators (machine feet)

Condition: used, Year of construction: 1979, pressure 100 t stroke 500 mm table surface area 4000x500 mm weight of the machine ca. 5,7 t Bdodpfx Aey Tpr Ajbwjc HY – S 100 RH MAE hydraulic straightening press, complete with straightening unit Year of manufacture: 1979 Approved in accordance with UVV Stroke: 500 mm Pressure capacity: 100 tonnes Table: 4000 x 500 mm Weight: 5700 kg

Condition: used, functionality: fully functional, Orma C4 veneer press, shelf type, 2200x1200 Shelf length: 2200mm Shelf width: 1200mm Maximum clearance between shelves: 475mm Maximum operating pressure: 150 bar Press with 4 actuators Hydraulic pump motor: 1.1 kW Shelves heated using hot water from the central heating system. Bdjdpfx Aezaiimsbwec

Condition: used, manufacture Hydrap In our assessment, the machine is in good used condition and can be inspected under power by appointment. Bedpfxoy Tpq Se Abwedc Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes, errors in technical data and specifications, and prior sale!

Condition: used, Punching force: 200 kN Thread, for example a 13 mm hole in 12 mm steel Viewfinder via handwheel Bsdjrmudgspfx Abwodc Assortment of tools is included in the price

Year of construction: 2025, condition: new, New machine Year of manufacture: 2025 Features and technical specifications: Fully equipped in standard version with: - Robust, torsion-free steel frame, welded and bolted construction - Lamella pressure beam TOP with 6 elements, lamella pressure beam SIDE with 5 elements - Lamella pressure beams with proven tolerance compensation system (Ganner system) for tightly compressed carcass joints - Counter-pressure surfaces (side pressure wall, base) are 38 mm thick, coated, continuous support plates - Continuous pressing surface, height 95 mm, on lower vertical pressure beam - Electromechanical adjustment of both pressure beams via precision trapezoidal thread spindles (with increased lead and concentricity accuracy) and high-performance ball nuts with grease reservoir - The pressing process is carried out electromotorically, via 2 independent worm gear motors (2 x 0.75 kW) - Pressing force of the pressure beams is infinitely variable and electronically controlled by 2 potentiometers, regulated via frequency inverter, ensuring absolutely wear-free force control - Pressing force for horizontal pressure beam: min. 500 daN (kg), infinitely adjustable up to max. 2200 daN (kg) - Pressing force for vertical pressure beam: min. 300 daN (kg), infinitely adjustable up to max. 2200 daN (kg) - Pressing and adjustment speed of the beams with fine positioning, using 3-stage selector switch: 5 / 10 / 25 mm/second - Jog mode for precise positioning of both pressure beams, e.g. for low pressing forces, drawers, and carcasses at 45° - Simplest operation via 6 separate push buttons, 8 movement cycles selectable via control panel - Freely adjustable press time preselection 0-30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressure beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 300 mm - Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm Including surcharge for rapid traverse speed, for fast positioning of the pressure beams, controlled via automatic workpiece detection with sensors in the pressure beams, pressing speeds 5 / 10 / 25 mm/sec and rapid traverse speed 50 mm/sec, the sensors can be deactivated for pressing special components Including a set of machine feet for 500 mm working height Bodpfx Ajw Nafksbwodc Location: Flörsheim Availability: Short-term

Condition: used, 1x bending knife from a VOEST press brake Length: 4050 mm Weight: approx. 120 kg For further dimensions see pictures. Bdsdpfx Ajy Tbvmsbwjc

Condition: used, Year of construction: 2011, pressure: 400bending length: 4050column width: 3400electricity performance: 37,5weight approx.: 25.000messurements (LxWxH): 5750 x 2110 x 3440STOCK CLEARANCE – UNBELIEVABLE PRICE!CNC Press Brake – DURMA AD-S 40400 (4 m x 400 tons) Now available at a special price ex works Böheimkirchen: only EUR 79,000 (Original price approx. EUR 170,000) Technical Specifications:Manufacturer: DURMA Model: AD-S 40400 Year of manufacture: 2011 Bending length: 4,050 mm Pressing force: 400 tons Axes: Y1, Y2, X, R + CNC-controlled crowning Motor power: 37 kW Features & Equipment:CNC crowning system, motorized adjustment via control Upper tool: 1010/A/75°, segmented and gooseneck-style Die: Multi-V die Backgauge: CNC-controlled 2 front sheet supports on linear guides CE-certified laser safety system (Lasersafe) mounted on the upper beam Machine fully complies with CE standards new pump installed One-time offer – available immediately!Only 1 unit in stock – ready for fast delivery – no lead time!Take advantage of this rare opportunity to own a high-performance CNC press brake at a fraction of the original price. Bdjdpfsvfy Sxjx Abwoc