Hydraulic press

SACK & KIESSELBACH TRP 200

Year of construction: 2001, condition: excellent (used), Used hydraulic press SACK & KIESSELBACH TRP 200. The originally automatic transfer press was converted to manual in 2012, but can be converted again as an automatic press. The press is still set up and under power and is in very good condition. Pressing capacity in t: 200 Quantity of oil in l: 1100 Stroke in mm: 300 Table size (lxb) in mm: 600 x 600 Daylight in mm: 1000 Upper ejector stroke in mm: 25 Upper ejector force in t: 10 Ncodpfx Akshtaaqoqjr Total weight in kg: 12000 Operating pressure in bar: 6 Approach speed in mm/sec: 375 Working speed in mm/sec.: 18 - 40

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight Nedpfxokvnumo Akqecr 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2006, travel distance X-axis: 730 mm, travel distance Y-axis: 730 mm, travel distance Z-axis: 850 mm, workpiece length (max.): 1,000 mm, workpiece weight (max.): 500 kg, number of slots in tool magazine: 120, controller manufacturer: FANUC, total height: 3,138 mm, total length: 2,725 mm, total width: 4,610 mm, overall weight: 12,900 kg, controller model: FS-31IA (MAPPS III), feed rate X-axis: 50 m/min, feed rate Y-axis: 50 m/min, feed rate Z-axis: 50 m/min, spindle speed (max.): 14,000 rpm, tool length: 500 mm, workpiece diameter (max.): 800 mm, CNC controller: FS-31IA (MAPPS III) Axes X-axis travel mm: 730 Nedpfx Aevw Sc Tokqjcr Y-axis travel mm: 730 Z-axis travel mm: 850 Rapid traverse m/min: 50 B-axis degrees: 360º (1º) Distance spindle nose - table surface mm: 100 – 830 Acceleration in the axes m/s2: 9.8 (X), 10.8 (Y), 6.9 (Z) Worktable Number of pallets: 2 Table dimensions mm: 500X500 Maximum workpiece size (D x H) mm: 800 X 1000 Max. workpiece weight kg: 500 APC time s: 7 Spindle Spindle speed rpm: 14.000 Spindle drive power kW: 22/18.5 Tool holder: No.40 Spindle torque Nm: 220 Tool system Tool holder: BT-40 Tool magazine slots: 120 With free neighboring places mm: 140 With occupied neighboring places mm: 70 Max. Tool Length mm: 500 Max tool weight kg: 12 Tool-to-tool time s: 0,9 Chip-to-chip time s: 3,3 Equipment Chip conveyor Workarea light CE conformity Coolant gun TOOL LIFE MANAGEMENT Cooling Tank capacity: 680 Machine running times Rated power kVA: 49 Basic machine dimensions / weight Length mm: 2.725 Width mm: 4.610 Height mm: 3.138 Weight kg: 12.900

Condition: good (used), Year of construction: 2000, table width: 1,000 mm, table length: 1,800 mm, ram plate width: 600 mm, total length: 25,000 mm, total width: 27,000 mm, total height: 47,000 mm, overall weight: 43,000 kg, die cushion stroke: 200 mm, Siemens Simatic OP 27 control system Ncedjtiwgispfx Akqer Light barrier Sick Separate control cabinet Ritta Side passages Ground level installation

Year of construction: 1999, condition: excellent (used), Control system: CNC-controlled and manual operation PC P 2000 MMX-PCI Desktop ATX 15" color display, keyboard CNC-Turbo Roughness for WINDOWS TECHNICAL DATA Granite test plate (DIN 876) Length x Width 1200 x 500 mm Accuracy grade Grade 2 Flatness: 16.6 µm Weight 250 kg Linear traversing unit Waveline 60 Basic Measuring stroke 60 mm Resolution 0.014 µm Measuring column Wavelift 400 CNC Travel distance 400 mm Positioning repeatability < 10 µm Nedpfxelxyp Hj Akqecr Machine dimensions (W x D x H) 1.8 x 0.8 x 2.2 m Weight 600 kg EQUIPMENT/ACCESSORIES  Complete enclosure with electrically operated roller shutters  Granite plate 1200 x 500 mm  ISEL feed axis with ball screw  Workpiece support plate  Linear feed unit Waveline 20/60  Measuring column Wavelift 400 CNC  Tilting unit KEG 60 on the measuring column, manual for Waveline  Built-in kit for roughness measurement  Built-in kit for contour measurement  Various probes and holders for roughness and contour measurements  Machine table  Emergency stop button on the machine table  Calibration set  Support prisms  Maintenance unit for compressed air preparation  Air damping elements for supporting the granite plate  Documentation

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor Nodpfog U Utvex Akqecr (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Year of construction: 2022, condition: like new (used), Due to the planned closure of our laboratory in May/June 2026, we are offering laboratory equipment for sale in very good and excellent condition. The entire set is available. All equipment has been used as intended, regularly serviced, fully operational, and ready for immediate use. The offer includes, among others: LCS MS/MS, GC MS, fume hoods, spectrophotometer, shakers, laboratory refrigerators, digestion unit, water bath, laboratory furniture, and many more. This is an excellent opportunity for research institutions, universities, and companies in the biotechnology, chemical, and medical sectors to acquire high-quality equipment at attractive prices. Early reservation of individual devices is possible. Collection is available from May 2026 or upon individual arrangement. We invite you to contact us and inspect the equipment on site in Poland, Warmian-Masurian Voivodeship. Nodpfx Aksxmhfrjqocr

Condition: used, TECHNICAL DETAILS - Number of axes : 4 MILLING SPINDLE - Tool holder type : BT40 BIG PLUS - Spindle power : 26 [kW] - Spindle speeds : 15000 [rpm] LINEAR AXES - Travels on X/Y/Z axes : 560/640/640 [mm] - Rapid traverses rates (X/Y/Z) : 60 [m/min] B ROTARY AXIS - Travel : 360 [°] - Indexing precision : 0.001 [°] TOOL CHANGER - Auto. Tool Changer type : Bras chargeur - Tool magazine capacity : 60 PALLET CHANGER - Pallet changing device type : Rotopalette - Pallet size : 400X400 [mm] - Pallets number : 2 - Maximum weight upon pallet : 400 [kg] - Maximum workpiece diameter : 630 [mm] - Maximum workpiece height : 900 [mm] POWER SUPPLY Nedpouhbv Sjfx Akqocr - Supply voltage : 400 [V] WEIGHT & DIMENSIONS - Machine floor space : 4100X2300 [mm] - Machine height : 2720 [mm] - Machine weight : 11000 [kg] MACHINE HOURS - Number of working hours : 3700 [h] EQUIPMENT - CNC : Fanuc 31 iB Interface : Ethernet / RS232 / USB / PCMCIA - Electronic handwheel - Linear scales - Rigid tapping - 3 colors status lamp - Coolant tank * with high-pressure pump : 25 [bars] * Coolant through spindle * With cabin washing - Chips conveyor : Arrière - Spindle cooling unit - Tool probe - Workpiece probe : Renishaw OMP60

Year of construction: 2006, condition: refurbished (used), HYDRAULIC PRESS MECAMAQ PRESSURE 350t STROKE 350mm TABLE LEFT RIGHT 600mm Ncodpfxofmqqls Akqer TABLE FRONT BACK 750mm POWER 15kw Dimensions: Height: 2,9m Width: 1,9m Length: 1,3m Weight: 5.700 kgr

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm Ncjdohlnzkopfx Akqer transport height 2950 mm weight of the press approx. 11 ton.