Used Groove Machine for sale (65,008)

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Dedoxy Tmnepfx Ak Aekw

Condition: used, Year of construction: 2016, Industrial automatic edge banding machine SOLUTION XD KEY FEATURES "E-TOUCH" CONTROL WITH AUTOMATIC PROGRAMMING: A SINGLE "TOUCH" IS ALL IT TAKES TO OPERATE THE MACHINE STANDARD PRESSURE DEVICE WITH DRIVE BELT FOR OPTIMAL PANEL GUIDANCE EDGE BANDING OF ROLL MATERIAL, STRIP EDGES AND SOLID WOOD EDGES GENERAL FEATURES Single-sided edge banding machine in left-hand version for edge banding of roll material and strip edges with all conventional hot melt adhesives. The base frame consists of a stable steel welded frame with higher rigidity, which provides optimal support for the installation of the processing units. The upper pressure beam consists of a thick-walled steel profile and a double trapezoidal drive belt, which is automatically positioned according to the panel thickness. Height adjustment with display on the upper pressure beam and on the operator panel. Manual workpiece feeding system with a large-sized work area and increased support surface facilitates the feeding of large workpieces. Adjustable infeed fence for two positions with automatic selection for processing with or without a pre-milling unit. Upper working units are attached to the pressure beam and mechanically connected to ensure automatic adjustment when changing panel thickness. Lower working units are attached to the machine frame or to the longitudinal support for precise referencing to the panel. All high-frequency motors are operated via frequency inverters. Each unit is equipped with its own inverter for optimal flexibility and improved machine production times. Protective hood for all units positioned after the glue application unit. Polycarbonate windows ensure a good view of the units during processing. Interior lighting of the hood. Protective hood with sound-absorbing material for lower noise emissions during operation. Spacer on the infeed fence allows the machine to be fed with the correct spacing. The spacing is automatically adjusted to the selected feed rate. Dust extraction port arranged on the pivoting control panel, positioned in the infeed area, is adjustable for ergonomic operation. The electrical system complies with current regulations. Electrical components are housed in a metal housing, attached to the machine frame and equipped with doors for easy access in case of maintenance. Standard voltage is 400 V EU 50 Hz (with neutral conductor). Material feed is via a feed chain with 80 mm wide chain plates made of rubberized nylon, for optimal guidance and high load capacity. The chain slides on 2 guides made of hardened and ground steel, one round and one flat guide, to guarantee straight feed and to protect against lateral displacement. Automatic chain lubrication. The amount of lubricating oil is optimized by the control system depending on the panels being processed. External support roller track positioned along the entire length of the machine; consisting of an extendable opening system up to 650 mm (for panels with a maximum width of 1200 mm). E-TOUCH PC control system for quick and easy execution of the main functions of the machine. Includes: – Processing of programs in Just in Time mode – Possibility of management via bills of materials – Possibility of management by Dkjdpfx Asxy Tm Ijk Asw

Condition: used, Year of construction: 1988, Bed milling machine Manufacturer: Correa Type: A16 Year of manufacture: 1988 Control: HEIDENHAIN TNC415 Travel distances X/Y/Z: 1,800 x 800 x 800 mm Clamping area: 2,000 x 630 mm Workpiece weight: 3,000 kg Djdpfx Ajzt U T Ask Ajkw Operating hours: 12,103 Power: 19 kW Spindle type: ISO 50 Dimensions L/W/H: 4,886 x 2,720 x 2,500 mm Machine weight: 7,500 kg 31126

Condition: like new (used), Year of construction: 2026, functionality: fully functional, Double side planer (Double Surface Planer ) extra wide 610 mm Maximum working width 610 mm Maximum working height 200 mm Heavy cardan feed system Dkedpj Ahif Ejfx Ak Asw Special spike feedsystem Unlike the conventional chain drive systems, this machine employs a patented synchronized transmission system along the four fitting columns. Electronic height adjustment Spiral cutterheads top and bottom Latest generation IE-3 motors Spindle and feed brakes CE

Condition: used, Year of construction: 1987, functionality: fully functional, Surface grinding machine Manufacturer: Geibel & Hotz, Model: FS 40 Primus Year of manufacture: 1987 Technical data Manufacturer: Geibel & Hotz Model: FS 40 Primus Year of manufacture: 1987 Grinding area (L x W): 400 x 200 mm Table width: 600 mm Djdo Ahif Topfx Ak Aokw Max. workpiece weight: 150 kg Magnetic chuck: 400 x 200 mm Longitudinal travel (X-axis): max. 420 mm Transverse travel (Z-axis): 205 mm Table speed: stepless, hydraulically adjustable Grinding wheel dimensions: Ø 225 x 25 x 51 mm Voltage: 3 x 380 V / 50 Hz Dimensions: approx. 1.50 x 1.30 x 2.20 m Weight: approx. 1,200 kg Equipment - Automatic transverse feed (Z-axis) - Rapid traverse for the vertical axis (Y-axis), combined with fine adjustment via handwheel - Central lubrication - Operating manual All information is provided without warranty. A demonstration under power is possible at any time in our showroom.

Condition: good (used), functionality: fully functional, Year of construction: 2019, operating hours: 25,995 h, control type: CNC control, degree of automation: automatic, controller manufacturer: Siemens, controller model: SINUMERIK 840D SL, laser type: diode laser, laser source manufacturer: TRUMPF, laser hours: 14,600 h, laser power: 4,000 W, sheet thickness steel (max.): 20 mm, sheet thickness stainless steel (max.): 25 mm, sheet thickness aluminum (max.): 20 mm, sheet thickness brass (max.): 8 mm, sheet thickness copper (max.): 8 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, feed rate X-axis: 100 m/min, feed rate Y-axis: 100 m/min, feed rate Z-axis: 100 m/min, workpiece weight (max.): 900 kg, input current: 42 A, type of cooling: water, year of last overhaul: 2026, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, Special equipment: + LiftMaster Compact 1530 (Type AL34) with loading cart + 3001 on TruDisk 4001 + BrightLine fiber + Nozzle changer + Wireless Operation Point + Performance package for fusion cutting + High-speed cutting package + High-speed eco cutting package + Copper cutting package + Brass cutting package + Transverse conveyor with tilting hopper + Storage interface + LiftMaster Compact 1530 (Type AL34 with loading cart) + Auxiliary pallet operation with loading cart + Safety fence Optional, at an extra cost: 1. Assembly, commissioning, partial overhaul and training of up to 3 operators at the customer's site, with a functional guarantee upon acceptance. 2. Workshop overhaul of the machine with commissioning and acceptance according to manufacturer's specifications in our workshop. Assembly, commissioning of the machine, and training of up to 3 operators at the customer's site. Standard equipment: - Closed machine frame - Automatic pallet changer in the longitudinal direction - Torque drive in combination with linear direct drives - Closed beam guidance via fiber optic cable - Machine cooling unit (water-air) - Integrated control cabinets with internal lighting - Longitudinal conveyor - Work area lighting - Positioning laser diode - Spraying device - PierceLine - FocusLine - NitroLine - PlasmaLine - Automatic nozzle cleaning - Transport and assembly device TRUMPF Laser - Solid-state laser TruDisk with 1 fiber optic output - Laser cooling unit (water-air) - Excitation via pump diodes - Laser power control Cutting unit - Universal cutting unit - Single cutting head strategy - Protective glass against lens contamination - ControlLine: Height control and sheet edge detection Control system - Workshop programming (TruTops via network access) - Quick reproduction - Touch color screen - Integrated technology data - Automatic shutdown - Programmable cutting gas/pressure selection - ContourLine - Microweld - FastLine - FlyLine - AdjustLine Dkjds Ahhu Uspfx Ak Asw - Teleservice via internet Data transfer - USB interface - RJ-45 network connection Safety - CE marking - Light barriers - Multi-chamber extraction system - Compact dust collector - Machine enclosure with certified viewing window (right door) - Roof cover

Condition: as good as new (ex-display), Year of construction: 2024, bore capacity in steel (diameter) 32.0 mm throat 230 mm Djdpfx Ajw U U N Ijk Aokw bore stroke 120 mm morse taper 3 MK table: 400 x 320 mm turning speeds 105 - 1725 U/min total power requirement 1.2 kW weight 245 kg range L-W-H 470 x 810 x 1710 mm Furnishing: - Compact, stable cast iron construction in a modern design - Infinitely variable speed control - is changed The speed is read on a digital display - Table height adjustment via rack and crank - Right and left rotation of the quill for thread cutting - Powerful 2-stage motor, speed range from 105 - 1725 rpm - Base plate with T-slots for clamping high workpieces - Safety switch with undervoltage release - The spindle runs in the precision ball bearing scope of delivery - Key chuck 1 - 13 mm / B 16 - Drill chuck arbor MK 3 / B 16 - Reducing sleeve MK 3/2 - Digital speed display - LED machine light - Height-adjustable protective cover

Condition: excellent (used), Year of construction: 2000, Sanding belt dimensions: 75 x 2000 mm Contact wheel width/diameter: 75/200 mm Sanding belt speed: 15/30 m/s Drive motor: 380 V, 4 kW Adjustable face grinding table: 75 x 430 mm Space requirement: 1000 x 450 x 1100 mm Dsdpfoznh I Nox Ak Aokw Weight: 95 kg

Condition: used, boneless meat, sausage, cheese, or fish 400V, 50 Hz/3/N/PE 32A approx. 10 kW compressed air connection values: min. pressure 4 bar cutting system sickle blade: max. speed at blade head WSK 2,000 min-1 Drive: feed, cup, portioning unit CCU: servo motors Drive power transmission: toothed belts Feed power transmission: precision ball screw drive Cutting thickness: 0.1 to 100 mm (depending on product and cutting capacity) Dkjdpfs Ahn Uksx Ak Aow product passage width: adjustable up to max. 380 mm product passage height: adjustable from 125 to max. 180 mm (optionally up to 200 mm) programming: dialogue via touch screen program memory locations: 100 2 sickle blades total dimensions (L x W x H): ± 3,000 x 1,600 x 2,700 mm + "Wibotec" single-pan weighing scale Type Continuous checkweigher 200 - Web 99T 355 -365 Web Module Length: approx. 485 mm Width: approx. 535 mm Weight: approx. 150 kg Power transmission of the drives: gears 9 g - 3750 g + Monosorting rocker Type CCR Length: approx. 450 mm Width: approx. 380 mm Weight: 250 kg Drive power transmission: toothed belts Motor type: asynchronous motors or servo drives, depending on the slicer type + Conveyor belt Type CCE total dimensions (L x W x H): ± 4,100 x 960 x 1,500 mm drive power transmission: toothed belts motor type: asynchronous motors or servo drives

Condition: used, CNC Vertical Machining Center FEHLMANN Type PICOMAX 60 CNC Control System: HEIDENHAIN TNC 426 Serial No.: 14599641 Year of manufacture: 1999 Travel paths X: 500 mm, Y: 350 mm, Z: 610 mm Feed rate: 1 - 20,000 mm/min Rapid traverse: 20 m/min Feed force: 12,000 N Table clamping surface: 920 x 380 mm T-slots: 7 pcs, 12-H8 mm Table load capacity: max. 250 kg Table height: 1004 mm Distance spindle nose - table: 94 - 704 mm Overhang spindle - column: 405 mm Spindle speed: 50 - 18,000 rpm, stepless Spindle drive: 10.2 kW (60% duty cycle) Max. torque: 70 Nm (up to 1240 rpm) Spindle taper: SK 30 / DIN 69871A Pull stud: DIN 69872 Drilling capacity in steel: 25 mm Milling capacity in steel / aluminium: 100 / 700 cm³/min Thread cutting in steel / aluminium: M20 / M24 Tool changer: 24 positions Tool change time: approx. 6 sec. Chip-to-chip time: approx. 8 sec. Control: Heidenhain TNC 426 Djdpfx Akoy N Du Do Askw Power supply: 400 Volt, 50 Hz Connected load: 20 kW - Electronic handwheel Heidenhain HR410 - 3D probe Renishaw MP12 - Tool measurement system - TFT display - Direct path measuring system - Coolant system (200 liters, lateral) - Spindle cooling unit (lateral) - Central lubrication Vogel - Air supply: 6 bar, 40 - 200 l/min - Oil mist extraction - Operating hours: - Control on: 97,000 h - Machine on: 80,000 h - Program run: 42,000 h Required space (L x W x H): 2,000 x 1,700 x 3,000 mm Weight: approx. 3.2 t Good condition

Condition: used, Servo press brake SAFAN Type SMK-P 50-2550 TS1 Downstroke bending machine with 4-axis CNC control Serial No. MK 285 Year of manufacture: 1998 CNC control SAFAN software version 5.07 TS1 Press force: 500 kN (50 tons) Working length: 2550 mm Stroke: 215 mm Clearance between side frames: 2700 mm Tool installation height: max. 414 mm Table width: 55 mm Table height above floor: 950 mm Approach speed: approx. 75 mm/s Return speed: approx. 75 mm/s Working speed: approx. 1.6 to 15 mm/s Motor power: 9 kW Power supply: 400 Volt, 50 Hz, 9 kW - 4-axis CNC control SAFAN software version 5.07 TS1, Y1 and Y2 axis for ram - 2-axis backgauge, X-axis (backgauge depth adjustment), R-axis (backgauge height adjustment) - 2 backgauge fingers, laterally adjustable by hand (Z1, Z2) - Ram drive via 2 servomotors and belt drive - Working speed steplessly adjustable Dodpfx Akoxpqy Ds Aekw - Operation via electric foot switch and/or two-hand control panel - 13 clamping holders for the upper tool (UKB system, type 50.571, UKB System A) - Tool holder for lower tool, 55 mm wide with 13 mm groove, 21 mm groove depth (Trumpf system or UKB System B) - Supplied without bending tools (a new set from UKB costs approx. 3,600 EUR net) - Displayed total operating hours = 8,120 h - Number of working strokes: 1,049,789 strokes Space requirements (L x W x H): 3450 x 1850 x 2650 mm Weight: 5,000 kg Good condition

Condition: used, Swing bending machine with additional segmented upper tool, gooseneck rail. Swing bending press brake FASTI type 2095-25-2.5, serial no. 94 295 004, year of manufacture 1994. Working length 2540 mm, max. sheet thickness 2.5 mm, upper beam stroke 380 mm, bending beam motor power 2.2 kW, power supply 400 Volt, 50 Hz. - NC control FASTImatic FM100 - one-piece sharp rail 135° - additional segmented upper tool, gooseneck rail - controlled backgauge - continuous stop rail - controlled bending angle via control - electric foot switches. Weight 3000 kg. In good condition. Dsdettc Uajpfx Ak Askw

Condition: good (used), Year of construction: 2003, Ref. -No.: 10618 Manufacturer: KELLENBERGER Type: 600 U Nr. 33 Year of construction: 2003 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175 - 250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0 - 5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 1500 / 1700 / 2200 / 3600 Swiveling grinding wheel head: 360 ° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Dkjdpfx Akj Ahkxcs Aow Micro-corrector of the feed, 1 division of the dial: 0,001 mm / Ø Working speeds continuously adjustable (normal / special): 20-400 / 10-400 Max. Grinding length: 900 mm Further information: The machine can be viewed while powered up.

Condition: used, Year of construction: 1997, turning speeds 3.000 U/min grinding wheel diameter 150 mm table-size 380 x 220 mm T-slots 1x 0 3~220 / 380 V total power requirement 0,37 kW weight of the machine ca. ca. 150 kg dimensions of the machine ca. 0,7 x 0,6 x 1,25 m Turning Tool Grinding Machine Dkjdpfx As Ahkgwok Aew GREIF - DHL K-0

Condition: good (used), Year of construction: 1973, Ref. -No.: 10658 Manufacturer: SCHARMANN Type: Opticut FB 140 Year of construction: 1973 Type of control: CNC Control: Heidenhain Storage location: Halberstadt Country of origin: Germany Machine-No.: 162XXX X-Travel: 3.000 mm Dodpfo Ahkyhjx Ak Askw Y-Travel: 2.000 mm Z-Travel: 1.250 mm Spindle Diameter: 140 mm Spindle Taper: ISO 50 Table Dimensions (Lengthxwidth): 1800 x 1500 mm Table Load: 15000 kg Turning Speeds: 2,3 - 810 RPM Spindle stroke: max.800 mm Total Power Requirement: 30 kW Table size: 2.000 x 1.500 mm Machine length: 7300 mm Machine width: 5600 mm Machine Height: 4000 mm Weight Of The Machine Ca.: 31 t Further information: - Faceplate with NC face slider and NC rotary table - Heidenhain digital readout - Various tool holders - Various clamping devices The machine can be viewed while powered on by prior arrangement.

Condition: used, Year of construction: 2002, travel distance X-axis: 400 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 450 mm, controller manufacturer: Heidenhain, controller model: iTNC 530, spindle speed (max.): 20,000 rpm, number of slots in tool magazine: 30, Machining Center - Universal Manufacturer: MIKRON Type: UCP 600 Year of manufacture: 2002 Control system: Heidenhain iTNC 530 Technical specifications: X-axis: 400 mm Dedpe Ahrm Sofx Ak Ajkw Y-axis: 450 mm Z-axis: 450 mm C-axis: 360° C-axis rotational speed: 30 rpm A-axis: +107° / -10.5° Spindle speed: 20,000 rpm Number of tool stations: 30 Condition: Used Technical features & accessories: - Oil/air lubrication system - Water cooler Accessories, tools, and clamping devices shown are included in the scope of delivery only if explicitly stated in the additional information. Subject to modifications and errors in the technical data and information; prior sale reserved!

Condition: used, Year of construction: 1970, taper MK 4 feeds: ja Dksdpfx Akexzu Dqj Aow weight of the machine ca. 1,5 t

Condition: good (used), Year of construction: 2011, functionality: fully functional, Technical details x-travel 500 mm y-travel 450 mm z-travel 400 mm Control Heidenhain iTNC 530 tool taper HSK 63 total power requirement 34 kVA weight of the machine ca. 4810 kg Accessories oil-mist-extractor Additional information Operating hours: 89.800 Spindle hours: 43.800 Machine with new milling spindle, replaced 2026. CNC control: Heidenhain iTNC 530 Equipment and accessories: Pallet changer (Automation PH 150/8) 60-position tool changer Electronic handwheel HR 410 Touch probe (TS) Chip conveyor Internal coolant supply system Dksdpfx Ake Ahn Hys Aow Oil-mist-extractor Machine without tool taper and clamping devices.

Condition: used, Year of construction: 1954, functionality: fully functional, grinding length 600 mm grinding width 205 mm x-travel 600 mm ja Dksdpfjvu Hkyex Ak Aew

Condition: good (used), Year of construction: 2012, Ref. -No.: 10469 Manufacturer: JAESPA Type: Comfort 420 A Year of construction: 2012 Type of control: N/A Dksdjy Ed D Dopfx Ak Ajw Control: N/A Storage location: Halberstadt Country of origin: Germany

Condition: good (used), Year of construction: 1990, Ref. -No.: 10544 Manufacturer: DECKEL Type: KF 2 Year of construction: 1990 Type of control: N/A Control: N/A Storage location: Halberstadt Country of origin: Germany Power Capacity: 1,6 / 2,0 kW Tool Taper: 20 mm Ø Space requirements: 1600 x 1350 LxWxH (mm) Feed rate: 0-350 mm / min Vertical portal passage, clamping table - lower beam cross member: 300 mm Distance table - spindle nose with vertical milling spindle: 50 mm Distance table - spindle nose with horizontal milling spindle: 450 mm Machine Height: 1950 mm Weight: 2,1 t Pre-milling spindle: 80...1000 min-1 Collets: 20 O taper bushing: Morse 1 Touch lift: 12 O Speed of the milling motor: 1400 RPM Further information: - Optical testing device - Pre-milling spindle - Model milling device - Rotary table - Inclined spindle - Mirror image milling device - Reduction and enlargement device - Roller engraving devices - Machine vice hydraulic clamps - Auxiliary clamping table - Dividing head - Tool cabinet - Clamping claws - template bars - articulated light Dksdo Ahmu Eepfx Ak Asw The machine can be viewed under power by arrangement.

Condition: good (used), functionality: fully functional, For sale is a used, custom-built box-clamping machine for the production and assembly of wooden boxes. The system is equipped with a total of 6 hand-operated clamping devices from the Senco brand. The clamping devices are activated via foot valves, allowing the box parts to be positioned and clamped together during the work process. Particularly suitable for the production of wine boxes, fruit boxes, vegetable boxes, and other wooden packaging. Technical data / equipment: Manufacturer: Custom-built Machine type: Box-clamping machine / Box assembly machine 6 hand-operated clamping devices Clamping device manufacturer: Senco Activation via foot valves Pneumatic operation For clamping box parts together Workpiece support / workbench Adjustable fixture for different box dimensions Robust frame construction Suitable for: Wine boxes Fruit boxes Dedpozynf Ssfx Ak Askw Vegetable boxes Packaging boxes other wooden boxes and wooden packaging The machine is in used condition. Equipment and condition as shown in the photos. Transport is possible for an additional charge! The machine is currently still at the customer's site but would be available shortly. The machine will be inspected before sale. For used machines with a year of manufacture of 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sale, and changes are subject to change. All information is without guarantee.

Condition: new, Year of construction: 2026, Ref. -No.: 10464 Manufacturer: IGREK Type: 3500 XXL Year of construction: 2026 Type of control: CNC-Steuerung Control: Siemens 840 D / Heidenhain iTNC 640 Storage location: Istanbul Country of origin: Türkiye X-Travel: 10500 mm Y-Travel: 3500 mm Z-Travel: 1400 mm A-Axis: +/- 115 ° B-Axis: 360 ° Max. Torque: 235 Nm Rapid Traverse X/Y/Z: 30 m / min Drive power spindle: 54 kW Table load max.: 4000 kg Tool Taper: HSK-A100 Spindle Speeds: 12500 RPM Machine length: 16000 mm Machine width: 7400 mm Machine Height: 8500 mm Weight: 195 t Further information: GREK 3500 XXL – Customized precision for large-scale projects Djdpfx Asxc Tr Ask Askw The IGREK 3500 XXL is a CNC 5-axis portal milling machine of the latest generation, developed for the high-precision machining of large components. Built in 2024, it is ready for immediate use and equipped with the latest technology to meet the most demanding requirements in heavy industry and mechanical engineering. Key features: Gigantic machining areas: With travel distances of 10,500 mm (X), 3,500 mm (Y) and 1,400 mm (Z), the machine offers extraordinary flexibility for machining large parts. 5-axis simultaneous machining: The A-axis with +/- 115° and the B-axis with 360° guarantee maximum precision and versatility when machining complex workpieces. Powerful spindle: Equipped with a speed of up to 12,500 rpm, a maximum torque of 235 Nm and a drive power of 54 kW – ideal for high-performance machining. Robust and durable: Weighing 195 tons and with a table load of up to 4,000 kg, the machine is designed for heavy-duty machining. Innovative tool holding fixture: The HSK-A100 tool holding fixture enables quick tool changes and increases efficiency. Speed and efficiency: Rapid feed rates of 30 m/min on all axes ensure maximum productivity. Technical data at a glance: Traverse paths: X 10,500 mm / Y 3,500 mm / Z 1,400 mm Spindle power: 54 kW Spindle speed: 12,500 rpm Table load: up to 4,000 kg Machine dimensions (LxWxH): 16,000 x 7,400 x 8,500 mm Weight: 195 tons Additional benefits: The machine is supplied with the advanced Siemens 840D or Heidenhain iTNC 640 control system and offers worldwide warranty and service support from the manufacturer. Choose the IGREK 3500 XXL for precision and efficiency in the machining of large parts. Contact us now for a non-binding offer!

Condition: good (used), Year of construction: 2012, Ref. -No.: 10659 Manufacturer: DECKEL MAHO Type: DMC 835V Year of construction: 2012 Type of control: CNC Control: Haidenhein iTNC 530 Storage location: Halberstadt Country of origin: Germany Machine-No.: 1541XXX X-Travel: 835 mm Y-Travel: 510 mm Z-Travel: 510 mm Number of T-slots: 5 Max. Tool Weight: 6 kg Max. Tool Length: 250 mm Max. Tool Diameter: 80 mm Tool change time: 1,6 s T - groove width: 14 mm Dsdpfx Aozw Tw Ujk Aekw T - slot spacing: 100 mm Tool Taper: SK40 Numbers Of Tools In Magazin: 30 Spindle Speed: 12000 RPM Max. Torque: 130 / 87 Nm Turning Speed Range - Stepless: 30 mm / min Total Power Requirement: 35 kW Dimensions Of The Machine Ca.: 4,5 x 3,5 x 2,7 m Weight Of The Machine Ca.: 5 t Changeover time chip - chip: 6 sec Feed rate: 1 - 20.000 (X / Y / Z) High pressure cooling: 20 bar Further information: The machine can be inspected while powered on by prior arrangement.

Condition: used, Year of construction: 1999, CNC machining center Manufacturer: Homag Type: BAZ 31/60/K Optimat Year of manufacture: 1999 Technical data - Workpiece length max. 6600 mm with single workpiece placement max. 2700 mm with alternating workpiece placement - Workpiece width max. 1200 mm - Workpiece thickness with edge max. 60 mm without edge max. 60 mm with standard clamp without edge max. 120 mm with clamping template when chamfer milling min. 12 mm when radius milling min. 2x radius + 10 mm - Working height, lower edge of workpiece 950 mm - 2 vacuum pumps, each with 66/100 m3/h for clamping system Main spindle 12 kW, water-cooled - for HSK F63 - Three-phase asynchronous motor 12 kW at S1, 600 Hz - Speed range: 1500 - 18000 rpm - Tool weight max. 6 kg incl. tool holder Dsdpfx Ae Ahmz Djk Ajkw Tool changer, 12 positions - for tools and aggregates with HSK F63 - 12 x diameter max. 130 mm or - 6 x diameter max. 180 mm and 6 x diameter max. 70 mm - Tool diameter for grinding tools max. 200 mm Aggregate interface BAZ for main spindle For accommodating the machining and gluing aggregates with integrated pneumatic-electrical-electronic supply and pivoting drive, C-axis. Swiveling range without limitation. Hose-free compressed air supply. Drilling head with 17 spindles - 1 motor 1.9 kW, frequency-controlled - Speed selectable via program 4500/6500 or 8000 rpm - Each spindle can be activated individually - Arrangement of spindles in T-shape. - 11 spindles in X-direction, 7 spindles in Y-direction Homatic control system CNC programming system WOODWOP Postprocessor Programming based on CNC drawing Laser positioning aid for vacuum clamping system Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.