Used Laminating Press for sale (13,074)

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Kledpfjzdn H Rjx Anyju Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), Year of construction: 2010, pressing force: 400 t, stroke length: 400 mm, throat depth: 405 mm, clearance between the columns: 4,050 mm, total length: 6,100 mm, overall weight: 34,000 kg, Equipment: CE marking, documentation/manual, Hydraulic press brake Manufacturer: EHT - Trumpf, Type: TruBend 8400-50S Year of manufacture: 2010 Technical data Manufacturer: EHT / Trumpf Type: TruBend 8400-50S Year of manufacture: 2010 Capacity: 400 t Bending length: 5050 mm Distance between uprights: 4050 mm Throat depth: 405 mm Stroke of Y-axis: 400 mm Installation height: 720 mm Table width: 140 mm Motor power: 37 kW Oil capacity: 600 L Pneumatic connection: 6 +/- 1 bar Dimensions: approx. L 6.1 x W 2.8 x H 3.67 m Weight: approx. 34 t Kjdpozd Tf Sefx Anyjlu Equipment • Controlled axes: X, R, Y1, Y2, Z1, Z2 • Control system: Cybelec ModEva 10S, 2D – graphic control • Upper tool clamping system Trumpf/Wila, hydraulic • Lower tool clamping system Trumpf, hydraulic • CNC-controlled crowning • Safety light curtain Lazersafe • 2 pcs. CNC bending aids incl. parking position • Pneumatic die shifting • Foot switch • Very large tool package, as shown in the photos • LCB angle measuring system (2 x front, 2 x rear) All information without guarantee.

Condition: used, Year of construction: 1963, total length: 2,300 mm, total width: 1,500 mm, total height: 2,880 mm, Empty weight: 8.000 kg - Year: 1963 - Documentation available: No - CE certificate present: No - Serial number: 12691 - Drive system: Conventional Klsdpjwmfrrofx Anyju - Press force [ton]: 160 - Min. stroke [mm]: 25 - Max. stroke [mm]: 118 - Table length [mm]: 950 - Table width [mm]: 650 - Ram width [mm]: 340 - Height adjustment [mm]: 75 - Motor power: 7.5kW - Transport dimensions: 2300mm x 1500mm x 2880mm (l x w x h) - Transport weight [kg]: 8000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1989, total length: 1,600 mm, total width: 1,700 mm, total height: 2,750 mm, Empty weight: 4.000 kg Klodpfx Aex Dkfponyeu - Year: 1989 - Documentation available: No - CE certificate present: No - Serial number: 4414 - Drive system: Conventional - Press force [ton]: 63 - Min. stroke [mm]: 8 - Max. stroke [mm]: 100 - Table length [mm]: 800 - Table width [mm]: 560 - Ram width [mm]: 300 - Motor power: 5.5kW - Transport dimensions: 1600mm x 1700mm x 2750mm (l x w x h) - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1981, total length: 2,000 mm, total width: 1,100 mm, total height: 2,300 mm, Empty weight: 500 kg - Year: 1981 - Documentation available: No - CE certificate present: No - Press force [ton]: 63 - Table length [mm]: 710 - Table width [mm]: 505 - Ram width [mm]: 280 Kljdpfx Ansxhcgyjysu - Throat depth [mm]: 250 - Transport dimensions: 2000mm x 1100mm x 2300mm (l x w x h) - Transport weight [kg]: 500kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1986, total length: 1,500 mm, total width: 1,450 mm, total height: 2,900 mm, Colour: Grey Empty weight: 5.500 kg - Year: 1986 - Documentation available: Yes - CE certificate present: No - Serial number: 88 09-86 - Drive system: Conventional - Press force [ton]: 63 - Min. stroke [mm]: 10 - Max. stroke [mm]: 100 - Table length [mm]: 710 Kodpfoylb Edjx Anyolu - Table width [mm]: 480 - Ram width [mm]: 320 - Height adjustment [mm]: 80 - Transport dimensions: 1500mm x 1450mm x 2900mm (l x w x h) - Transport weight [kg]: 5500kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2009, total length: 2,700 mm, total width: 1,700 mm, total height: 3,900 mm, Colour: Green Empty weight: 5.000 kg - Year: 2009 - Documentation available: No - CE certificate present: No - Drive system: Conventional - Press model: Workshop press - Press force [ton]: 200 Kedpfjzdnzhox Anyelu - Min. stroke [mm]: 1 - Max. stroke [mm]: 1100 - Table length [mm]: 730 - Table width [mm]: 1900 - Transport dimensions: 2700mm x 1700mm x 3900mm (l x w x h) - Transport weight [kg]: 5000kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, functionality: unexamined, Year of construction: 2018, This Wemhöner vacuum press, type: Variopress - Basic 1000S, with 3 paternoster magazines for film rolls, will be auctioned in our RESTLOS online auction "Wood and metalworking machines - vacuum press - veneer shears - metal circular saw". You can find this and many other machines from the field of wood and metalworking regularly on our RESTLOS auction platform. Machine data: Manufacturer: Wemhöner Type: Variopress - Basic 1000S Year of manufacture: 2018 Technical data: Heating plate format: 2850 mm x 1550 mm Type of electric heating plate: Aluminum heating plate on top Total pressing force: 2400 kN Chamber pressure max.: 6 bar Kedpfx Aezfal Usnyslu Operating temperature max.: 180 degrees Celsius Batch or workpiece size max.: approx. 2460 mm x 1180 mm Thermoplastic film as roll goods Width of the film: approx. 1430 mm Thickness of the film: approx. 0.25 mm - 1 mm Pressure chamber height: max. up to 180 mm Installed power: approx. 46 kW Required air pressure: approx. 8 bar Scope of delivery: - Including 3 paternoster magazines for film rolls Notes: - Machine has already been disassembled and stored - The technical data and descriptions are a copy of the original order confirmation. The data is for informational purposes only and is not binding. As shown in the pictures Without any other items or components shown in the pictures Functionality not tested

Condition: used, Year of construction: 1950, pressure 120 t draw back pressure 20 t Kledpfx Anex Sr Eveyou piston stroke 500 mm dayligth 600 mm usable table size 800 x 800 mm range L-W-H ca. 2,55 x 1,14 x 3,34 m weight ca. 3,5 t In our assessment, the machine is in good used condition and can be inspected under power by appointment. Accessories, tools, and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Technical data and specifications are subject to change without notice and errors. Prior sale is reserved.

Condition: good (used), Hydraulic press 10 tons. Installation height 400 mm Overhang 270 mm Width 1000 mm Without hydraulic pump Ksdpfxszdufys Anyelu Transport dimensions: Height without pallet 1440 mm Width 1000 mm Depth 780 mm Weight 325 kg

Condition: ready for operation (used), Year of construction: 1996, machine/vehicle number: 755T, functionality: fully functional, cutting length (max.): 3,050 mm, sheet thickness steel (max.): 8 mm, No minimum price – guaranteed sale to the highest bidder! Kledpfx Anszd U R Nsyeu Includes a second Siemens S5 control unit as a spare part! TECHNICAL DETAILS Steel sheet thickness: 8 mm Cutting length: 3,050 mm MACHINE DETAILS Hydraulic pressure: 250 bar Total weight: 10,000 kg EQUIPMENT Cybelec documentation Wiring diagram Second Siemens S5 control unit (spare)

Condition: used, CNC Press Brake BEYELER - BYSTRONIC Type PR 8 (2500 kN x 3100 mm) Press brake with 6-axis backgauge and CYBELEC control Serial No.: Year of manufacture: 2001 Pressing force: 250 tons Working length: 3100 mm Stroke: 365 mm Throat depth: 410 mm Clearance between side frames: 2750 mm Table width: 100 mm, 200 mm with table extension Table height above floor: 840 mm Backgauge X-axis: 620 mm travel Backgauge R-axis: 240 mm Approach speed: 200 mm/s Working speed: 1-10 mm/s Y rapid traverse: 200 mm/s Y working traverse: 1-10 mm/s Y return: 135 mm/s Oil capacity: approx. 400 liters Motor power: 18.5 kW Connected load: approx. 25 kW Power supply: 400 Volt, 50 Hz, 50 Amp. - 8 axis CNC control Cybelec DNC 1200 PS/A, X1 + X2 / R1 + R2 / Z1 + Z2 - 2 freely programmable backgauge fingers, laterally movable (Z1+Z2) - Backgauge (X-axis 620 mm) with 3 gauging points up to max. 1080 mm - Ram with servo valves and measuring system Y1 and Y2 - FIESSLER AKAS safety light barrier - Operation via electric foot switch and/or two-hand control panel - Hydraulic upper tool clamping (TRUMPF system) with 20 mm clamping slot - Tool holder for lower tool, height 160 mm x width 60 mm, with holder slot 14 x 23 mm - Tool system TRUMPF, without tools Kledsya Iaqjpfx Anyou Space requirement (L x W x H): 0 x 2500 x 3400 mm Machine transport height: 3360 mm Weight: 17,000 kg Good condition

Year of construction: 1992, condition: used, Pressing force 40 t Effective stroke 500 mm power capacity 17 kW tracking travel 48 mm Overrun time 110 ms safety distance 176 mm In our assessment, the machine is in good used condition and can be inspected under power by appointment. Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes, errors in technical data and specifications, and prior sale! Kljdpfszdvcajx Anyou

Condition: good (used), Year of construction: 2006, functionality: fully functional, power: 6 kW (8.16 HP), stroke length: 200 mm, Hydraulic press brake Manufacturer: AMADA, Type: HFP 50-20 Year of manufacture: 2006 Technical data Manufacturer: AMADA Type: HFP 50-20 Year of manufacture: 2006 Usable length: 2090 mm Capacity: 50 t Distance between uprights: 1,665 mm Stroke: 200 mm Overhang: 400 mm Installation height: 470 mm Motor power: 6 kW Dimensions: approx. L 2.95 x W 1.60 x H 2.45 m Weight: 4.7 t Equipment • Controlled axes: X, R, Z1, Z2 • FIESSLER light curtain at the front • Amada upper tool clamping system • CNC control 3D AMNC graphic • Rear protective device (swiveling grating doors) • Swiveling control panel – front left • Technical documentation • Tools: o Upper tool, straight, 28°, length 2,050 mm, sectional o Upper tool, slightly bent, R1, H 100 mm, L = 2,100 mm, sectional o Lower tool V25/30°, length 2,050 mm o Lower tool, pressure pad, length 2,050 mm Kledpozdtrxsfx Anyju o Lower tool, 4-way block die, L = 1,800 mm, sectional All information is subject to change without notice. A demonstration under power is possible at any time in our showroom.

Condition: good (used), Year of construction: 1986, functionality: fully functional, Pressing force: 1250 kN, stroke rate: 55 min⁻¹, ram adjustment: 75 mm, stroke: 20–120 mm, motor power: 11 kW, voltage: 380 V, machine weight: 8.6 t, throat depth: 340 mm, ram clamping surface: 620 x 300 mm, table clamping surface: 650 x 1000 mm, Ortlinghaus hydraulic clutch with double brake, two-hand control, ram damage has been professionally repaired. Kledoxxa Aajpfx Anysu

Condition: used, Year of construction: 2006, Fully functional Ksdpfx Anszd Tnaoyslu

Condition: used, Year of construction: 2006, Fully functional Kjdpfezd Tm Njx Anyolu

Condition: used, Year of construction: 2011, Fully functional Klodpfezd Tlrex Anysu

Condition: reconditioned (used), functionality: fully functional, year of last overhaul: 2026, type of input current: three-phase, overall weight: 350 kg, input voltage: 400 V, total length: 500 mm, total width: 520 mm, total height: 1,200 mm, input frequency: 50 Hz, DGUV certified until: 08/2027, Dough divider and forming machine Record roll press Newly revised dividing head New stainless steel knife Connection: 400V, 16A CEE plug Dimensions: 520 x 500 x 1200 mm (W x D x H) Ksdeuav Itopfx Anyslu Used machine, refurbished with warranty + spare parts service Option: ONLY AVAILABLE FROM US! New forming plate Delivery service Stainless steel platform Maintenance contract Training and commissioning You will find a large selection of roll presses only with us!

Condition: excellent (used), functionality: fully functional, input voltage: 400 V, DGUV certified until: 08/2027, type of input current: three-phase, overall weight: 500 kg, year of last overhaul: 2025, Eberhardt Optimat S 4 Roll Press Stainless steel design Simple manual operation Stand-alone machine, dough divider and rounding machine Kedsy Hwmhspfx Anyjlu Top-quality roll press with 3 rounding plates TAS system, 30-piece For round and square rolls DGUV V3 certified – available only from us Connection: 400 V, 16A CEE plug Used machine We have many other bakery machines in stock!

Condition: good (used), Selling CRATHERN, PERONDI IA630, NA 900. Kledpsud Axgefx Anyju

Condition: good (used), For sale is a professional laminator IBICO IL-12HR (A3). This device is ideal for offices, copy shops, schools, or small print shops. Technical specifications: • Manufacturer: IBICO • Model: IL-12HR • Type: Hot laminator (Pouch Laminator) • Max. laminating width: 320 mm (A3) • Operating voltage: 230V / 50Hz • Power: 1100 W • Temperature range: up to 160°C • Multiple speed settings • Digital temperature display • Reverse function Condition: Used, fully functional. Normal signs of use (see photos). The device heats up correctly and operates reliably. Scope of delivery as shown. Advantages: Kljdpfx Anjufgn Isyeu • Robust metal construction • Suitable for continuous operation • Even heat distribution • Ideal for A3 and A4 documents • Also suitable for thicker laminating pouches

Condition: excellent (used), For sale: Complete industrial pneumatic press in a workshop housing, ideal for punching, pressing, stamping, or other assembly processes. The set includes: • Pneumatic column press with a robust steel frame • Control valve, cylinder, and pneumatic distribution • Integrated control panel with emergency stop switch Klodpfx Anoud Rddsyou • Steel worktable with adjustable side guides • Power cabinet, distribution board, and cable management • Mobile table with transport brake Drive: Pneumatic supply Control: Solenoid valves, start/stop buttons Power supply: 230 V (electric system integrated in the base) Technical condition: Very good. Used, fully functional set ready for immediate use in a production facility. Genuine industrial construction, not for amateur use.

Condition: excellent (used), For sale, Form thermostat - Tool Temp TT-188 Max. heating temperature - 90°C Medium - water Power: 9850 Watts The device has: Klodpfevzb Nqsx Anyeu - vacuum pump vaccum - vacuum tank - function of sucking the medium out of the mold - the device can be integrated with the machine, maintenance-free

Condition: excellent (used), Year of construction: 1985, I sell hydraulic press MÜLLER HEP 10.20.35, year of production 1985. the press worked until the very end in bdb condition. Review of the press in 2023. Kedpfsudph Ijx Anyslu