Used Nail Plate for sale (10,870)

Condition: used, functionality: fully functional, machine/vehicle number: 2550X10.14MM, control type: manual, degree of automation: manual, actuation type: mechanical, number of rollers: 3, roller (top) diameter: 300 mm, side roll diameter: 280 mm, roller diameter: 400 mm, roller length: 2,550 mm, working width: 2,500 mm, working height: 800 mm, sheet thickness (max.): 14 mm, sheet thickness stainless steel (max.): 10 mm, input voltage: 380 V, input frequency: 50 Hz, Equipment: centralized greasing system, cone bending device, emergency stop, swiveling upper roller, 3 roll 2500x14 mm Plate bending machine Model OMCCA ITALY CAPACITY plate width 2500 mm plate thickness 14 mm pre-bending 10 mm --- Useful rollers width 2550 mm Top roll d 300 mm Side rollers D 280 mm hard surface of the 3 rolls centralized gear unit side rolls driven Csdpsy Aubuefx Alwjrc Opening front hydraulic drop-end to unload the closed shell. Extended shafts to take installation of add-on molds for section bending Variable speed rolling up to 5 mtr/min power electric motor 20Hp on hydraulic unit console with electric push buttons commands. Dial gauge position rollers readout safety installations with emergency stop

Condition: used, Bed plate 10ft x 5 ft x 4000kgs (approx) - Matched Pair Cedsywziujpfx Alwerc

Condition: used, functionality: fully functional, machine/vehicle number: 7FBMF35-16267, Year of construction: 2013, operating hours: 6,500 h, load capacity: 3,000 kg, lifting height: 4,700 mm, fuel type: electric, mast type: triplex, Electric Forklift Truck – Toyota Year of manufacture: 2013 Technical data: • Model: Toyota 7FBMF30 • Load capacity: 3,000 kg • Drive: Electric (battery powered) • Mast type: Triplex with free lift Credpfx Aljw Hhwwewoc • Lift height: approx. 4,300 – 4,800 mm • Fork length: 1,070 mm (standard) • Tyres: Solid rubber • Cabin: Open design, optionally with driver protection roof • Condition: Used, serviced and fully functional

Condition: used, Cast bed Crjdpfxewnfz No Alwsc Length: 2410 mm Width: 1500 mm Thickness: 550 mm 8 T-slots 50 x 27 mm with 2 opening (possibility to close them) 1 opening L 560 x W 500 mm 1 opening L 480 x W 360 mm Weight: approx 5 T

Condition: used, Cast iron bed Length: 2300 mm Width: 1900 mm Thickness: 200 mm Crjdpfxswtc Hgo Alwsc Height on feet: 980 mm 5 T-slots horizontal and vertical T-slots dimensions: 60 x 35 mm Square dimensions: 365 x 365 mm Crack at a longitudinal T (see photo) Weight: approx 3 T

Condition: used, Cast iron bed 2600 x 2000 x 350 mm Length: 2600 mm Width: 2000 mm Thickness: 350 mm 8 T-slots T-slots dimensions: 55 x 35 mm Slots spacing: 250 mm Equipped with 12 leveling feet Csdpfx Aljwlhd Uswsrc Weight: approx 4,5 T

Condition: good (used), Cast iron bed - Floor Plate Useful surface (L x W x H): 3600 x 1200 x 300 mm Credpsh Auahjfx Alwsc 4 T-slots: width 44 x 26 mm Equipped with Levelling feet Weight: approx 3 T

Condition: used, Cast iron bed 2600 x 2000 x 350 mm Codpfx Ajwlhflolwsrc Length: 2600 mm Width: 2000 mm Thickness: 350 mm 8 T-slots T-slots dimensions: 55 x 35 mm Slots spacing: 250 mm Equipped with 12 leveling feet Weight: approx 4,5 T

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, roller diameter: 60 mm, working width: 1,050 mm, sheet thickness (max.): 1 mm, roll metal bending machine Isitan 1050 X 1.2mm Manual 3 roll Bending Machine, excellent condition for sale manufacturer: Isitan 1050X1.2 max sheet width: 1050mm max sheet thickness: 1.2 mm Wire grooves at the ends of the rollers Conical bender roller diameter: 60mm Upper roller removable for easy workpiece removal machine dimensions: Crsdpfjwk Rlxex Alwjc length: 130cm height: 100cm width: 65cm weight: 240kg

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1992, machine/vehicle number: 11/10575, working width: 3,000 mm, sheet thickness (max.): 16 mm, TECHNICAL DETAILS Sheet metal width: 3,000 mm Sheet metal thickness: 16 mm Control system: conventional Cjdjzapqwepfx Alwsrc MACHINE DETAILS Rated current: 63 A Voltage: 380 V

Condition: good (used), Top of the range plate washing system for high throughput. Has come from Wembley Football Stadium where it was washing plates for the hospitality areas. Lovely condition and with options Cjdpfx Ajvd Eiyelwjrc

Condition: used, Year of construction: 2008, total length: 4,500 mm, total width: 1,700 mm, total height: 1,200 mm, Empty weight: 7.000 kg - Year: 2008 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 20830013 Csdpfxoxdigfe Alwsrc - Drive system: Teach-in - Number of rolls [pcs.]: 3 - Number of driven rolls [pcs]: 2 - Power [kW]: 11.0 - Max. sheet thickness [mm]: 16 - Max. working width [mm]: 2000 - Transport dimensions: 4500mm x 1700mm x 1200mm (l x w x h) - Transport weight [kg]: 7000kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Credpfx Aszbqquolwoc Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Clamping plate with T-slots, plate field, welding table, welding table, plate boring machine, T-slot plate -Mounting plate: with T-slots -Length: 3045 mm -Width: 1300 mm -Height: 770/970 mm -Groove width: 23 mm Crjdpfjzbl Ihjx Alwjc -Slot spacing: 265 mm -Dimensions: 1300/3045/H770 mm -Weight: 2300 kg

Condition: good (used), Clamping plate, plate field, welding table, welding table, clamping plate, scribing and measuring plate, measuring table, straightening plate, short-stroke heavy-duty cylinder, hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, hydraulic press, bending machine, straightening machine, profile straightening system, strip straightening machine, strip straightening device, shaft straightening system, combined bending machine-straightening press, profile bending machine, bending machine bending/straightening press -Mounting plate: Mounting plate with straightening press -Length: 3260 mm -Width: 1380 mm Cjdpfszbhqxsx Alwerc -Piston diameter: Ø 63 mm -Stroke: 200 mm -Pressure force: t -Overall dimensions: 3260/1380/H1940 mm -Weight: 2820 kg

Condition: good (used), Clamping plate with T-slots, plate field, welding table, welding table, plate boring machine, T-slot plate Csdpfx Ajzbhn Delwsrc -Mounting plate: with T-slots -Length: 3050 mm -Width: 3000 mm -Height: 445 -Groove width: 28 mm -Slot spacing: 275 mm -Dimensions: 3050/3000/H445 mm -Weight: 4000 kg

Condition: good (used), Clamping plate with T-slots, plate panel, welding table, T-slot plate, clamping plate, scribing and marking plate, measuring plate, measuring table, leveling plate, scribing plate Crsdpfxjza Sxwe Alwec -Mounting plate: T-slot plate with solid base frame -Length: 3030 mm -Width: 3000 mm -Groove width: 25 mm -Dimensions: see photos -Overall dimensions: 3030/3000/H500 mm -Weight: 4500 kg

Condition: good (used), Clamping plate with T-slots, plate field, welding table, welding table, T-slot plate, clamping plate, marking plate, measuring plate, measuring table, straightening plate, marking plate -T-slot plate: clamping plate on solid base frame -Length: 3200 mm -Width: 1625 mm -Groove width: 30 mm -Dimensions: see drawing in the photos Cedpfsv D Hkrsx Alworc -Dimensions total: 3200/1625/H720 mm -Weight: 2300 kg

Condition: good (used), Clamping plate with T-slots, T-slot plate, punching table, clamping plate, plate field, -T-slot plate: Mounting plate with T-slots -Clamping surface: 1295 x 2000 mm -Sheet height: 90 mm Solid, planed underside -Groove width: 27 mm Crodpeyn Rc Rsfx Alwjc -Dimensions: see drawing in the photos -Overall dimensions: 1295/2000/H90 mm -Weight: 1587 kg

Condition: excellent (used), functionality: fully functional, Year of construction: 1998, Darley hydraulic guillotine shear type GS 3116 working width 3050 mm max sheet thickness 16 mm Delem NC control type DAC 350 motorized backgauge automatic angle adjustment automatic cutting gap adjustment rear side equipped with transport conveyor Cedpoxpuipefx Alwjrc

Condition: used, Year of construction: 2005, sheet width 3100 mm plate thickness 12 mm distance between columns 3260 mm back stop - adjustable 3 - 1250 mm power capacity 37 kW voltage 400 V Crodpfjzbc Acox Alwoc weight of the machine ca. ca. 14 t dimensions of the machine ca. 4,00 x 4,00 x 2,20 m CNC-controlled plate shear

Condition: used, Clamping plate, clamping table, machine table – HOME-MADE Can also be used as a straightening plate or welding plate. Table surface: 2150 x 1040 mm Overall height: 200 mm - Top and bottom surfaces are parallel and machined, surfaces are planed. - Table plate dimensions: L x W x H = 2150 x 1040 x 65 mm - Table plate has several symmetrical holes. Table plate with M16 and M24 threaded holes: M16, M24, M16, M24, etc. Hole spacing in the length: approx. 250 mm Hole spacing in the width: approx. 255 / 165 / 255 mm Crsdpfotqgnyex Alwsc - 6 double T-beams welded onto the steel plate. Double T-beam dimensions: L x W x H 2150 x 125 x 135 mm Distance between the double T-beams: 50 to 55 mm Weight: 1730 kg Good condition.

Condition: good (used), Clamping plate, plate field, welding table, welding table, clamping plate, scribing and measuring plate, measuring table, straightening plate, short-stroke heavy-duty cylinder, hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, hydraulic press, bending machine, straightening machine, profile straightening system, strip straightening machine, strip straightening device, shaft straightening system, combined bending machine-straightening press, profile bending machine, bending machine bending/straightening press -Mounting plate: Mounting plate with straightening press -Length: 4025 mm -Width: 1990 mm Credpfxjzakf No Alwoc -Piston diameter: Ø 63 mm -Stroke: 110 mm -Pressure force: 20 t -Overall dimensions: 1990/4025/H1920 mm -Weight: 5060 kg

Condition: used, Year of construction: 2008, only approx. 20K plates done RIP Cjdpeza A D Dofx Alwerc York Workflow Inlinepunch 425 Azura C95 Clean out unit Available: at short term

Condition: good (used), Year of construction: 2000, Cast iron measuring and marking table with under-table cabinet, STOLLE MT1000. Table: 1000 x 1000 mm Height: 1000 mm Weight: approx. 650 kg In good condition. Csdpfjwffz Dex Alwjrc