Used Plasma Cutting Device for sale (23,653)

Condition: used, Year of construction: 2014, ■ V304 plate cutting machine capable of processing plates up to 1.500mm x 3.000mm ■ V304 plate processing machine (including gantry beam 2.500mm and side trucks) ■ X-rail (5.000mm on both sides of the machine, including double linear guides, helical rack and pinion system and rubber covering band) ■ Plasma cutting and extraction table (1.600mm x 3.090mm, 1 pcs) ■ Plasma cutting unit Kjellberg HiFocus280i (1 pcs) ■ Torch suspension for plasma cutting unit (including IHT M4000 PCS automatic height control) ■ Carriage for cutting unit (motor driven, including laser pointer, 1 pcs) ■ Kemper fume extraction unit 81 0550 090 (including spark trap 1 pcs) ■ Hardware and software (includes VACAM ‘Machine Edition’, VACAM ‘Office Edition’, VACAD editor software module, VANEST nesting software, Layout marking software module) ■ Safety devices (safety bumpers, emergency stop cord) Technical specifications PLASMA CUTTING UNIT HIFOCUS 280i Material Mild steel, stainless steel, aluminum Min. thickness 3 mm Max. thickness 70 mm Max. pierce capacity 40 mm Dross-free cutting max. 35 mm Automatic height setting Yes, IHT M4000 PCS Marking lines Yes, with same consumables Plasma gas mild steel Cutting O2 (99,9% pure clean, dry, oil-free) Marking Argon gas Shield gas mild steel O2 / air (99,9% pure clean, dry, oil-free) Automatic gas console Yes Cutting speed mild steel 6 mm Approx. 4.100 mm / min 90A 12 mm Approx. 3.200 mm / min 160A 25 mm Approx. 2.000 mm / min 280A 40 mm Approx. 720 mm / min 280A 50 mm Approx. 400 mm / min 280A 70 mm Approx. 150 mm / min 280A * Grounding max. 6m of machine: AC power, PE and service grounds must be connected to all equipment according to local and national codes. COLOUR Plates RAL 3003 Red Kodpey E Nykofx Ap Dedu Frames RAL 7011 Grey GENERAL INFORMATION Working height 700 mm (+/- 20 mm) Voltage stabilizer Not included Ambient temperature 0 – 35°C max. 95% relative humidity

Condition: used, Year of construction: 2018, functionality: fully functional, Working area: 3000 × 1500 mm Design: Downdraft / fume extraction table Plasma source: Hypertherm Powermax65 Max. current: 65 A Plasma source power supply: 400 V / 3-phase Compressed air: min. ±5.9 bar CNC plasma cutting machine with automatic torch height control Kdedpez Iniqsfx Ap Dou

Condition: like new (used), Year of construction: 2025, operating hours: 150 h, functionality: fully functional, working range: 6,000 mm, sheet thickness (max.): 200 mm, sheet thickness steel (max.): 200 mm, sheet thickness aluminum (max.): 80 mm, cutting height (max.): 200 mm, table length: 6,000 mm, working width: 2,000 mm, table width: 2,000 mm, type of cooling: water, Equipment: documentation/manual, double-sided, MicroStep MasterCut 6001.20PG – 6,000 × 2,000 mm – Plasma + Oxyfuel For sale is a MicroStep MasterCut 6001.20PG CNC plasma/oxyfuel cutting system with a working area of 6,000 × 2,000 mm, manufactured in 2025. Equipped with a Kjellberg SmartFocus 300 fine plasma power source and an additional fully automatic oxyfuel cutting system. The system is designed for processing steel, stainless steel, and aluminum. Key technical specifications: - Working area: 6,000 × 2,000 mm - Plasma: up to 80 mm - Oxyfuel: up to 200 mm - Kjellberg SmartFocus 300 Amperes - Fully automatic plasma support - Fully automatic oxyfuel support - Automatic gas consoles Ksdpfx Asz Hcr Dop Dodu - Elevated gantry design - Smart Z movement - Active collision protection - MicroStep control with 24" touchscreen - Asper Basic 2D CAD/CAM - RemoteDiagnostics Included with the system is a Donaldson DFPRE 4-R filter/extraction system with 9.0 kW. The extraction system is explosion-proof and equipped with appropriate ATEX features, making the system suitable for cutting aluminum. The machine has been used very little and is in good condition. Inspection and demonstration under power are possible by appointment.

Condition: used, Year of construction: 2016, operating hours: 2,170 h, functionality: fully functional, input voltage: 400 V, total width: 3,880 mm, total length: 3,100 mm, input current: 160 A, Equipment: documentation/manual, MGM Omnicut Star 3100 CNC plasma cutting system Manufacturer: MGM Kjdpfx Aozpwcfop Dedu Model: Omnicut Star 3100 Year of manufacture: 2016 Operating hours: approx. 2,100 h For sale is a well-maintained MGM Omnicut Star 3100 CNC plasma cutting system from 2016 with only approximately 2,100 operating hours. The machine is in good technical condition and is ready for immediate use. Equipment: CNC plasma cutting system MGM Omnicut Star 3100 Year of manufacture 2016 Approx. 2,100 operating hours Plasma source: Kjellberg HiFocus 161i neo Additional oxy-fuel torch for economical oxy-fuel cutting Precise machining of steel, stainless steel and aluminum Robust machine construction for industrial use The combination of the powerful Kjellberg HiFocus 161i neo and the oxy-fuel torch enables both highly precise plasma cuts and the economical cutting of larger material thicknesses. Note regarding the sale: We offer this machine on behalf of a client and act solely as an intermediary. The sale is made directly by the machine's owner. We will gladly facilitate contact and assist you with the entire process. An inspection of the machine is possible at any time by prior appointment. We will gladly provide further technical data, images and information on the equipment upon request. We look forward to your inquiry.

Condition: used, Year of construction: 2008, functionality: fully functional, machine/vehicle number: 962157, type of input current: AC, input voltage: 230 V, overall weight: 3,500 kg, sheet thickness steel (max.): 150 mm, working length: 6,000 mm, protection type (IP code): IP21, cutting speed: 12,000 mm/min, table length: 6,000 mm, table width: 2,000 mm, working width: 2,000 mm, We offer a used plasma and oxy-fuel cutting machine, Varstroj VARCUT 3.2 L2/Ph - 2.5x6.0/1(PL+G). Serial number: 962157 Connection voltage: ~230 V Frequency: 50 Hz Connection power: max. 2.0 kVA Maximum cutting speed: 12000 mm/min Control: CNC Number of torches: 1+1 Cutting thickness (oxy-fuel): 150 mm Working width: 2000 mm Working length: 6000 mm Cutting gas: Propane butane, air Mechanical protection: IP 21 Total weight: approx. 3500 kg Year of manufacture: 2008 Plasma: TRC-121 OTC Daihen D-12000 30-120A Cutting up to 25 mm thickness with plasma Kdedpfez D Tq Esx Ap Deu If you have any further questions or require more information, please send us a message or call us.

Condition: good (used), MicroStep SPL-PA plasma cutting system with extraction and compressor technology Manufacturer: MicroStep Group Model: SPL-PA 4501.15+S50 Current requirement: 120 A Machine type: CNC plasma cutting system CNC control: iMSNC Design: Portal design with linear guides Extraction system: Donaldson Torit DCE Electrical connection for extraction system: 400 volts Kdedpfxjyvd Uis Ap Dou Motor power of extraction system: 7.5 kW Compressed air generation: Screw compressor Compressor manufacturer: Kaeser Compressor model: TA 8 CE marking: present Location: Waltenhofen, Germany Dismantling and loading by the seller included.

Condition: as good as new (ex-display), Year of construction: 2023, functionality: fully functional, working range: 1,500 mm, total length: 4,500 mm, track width: 2,000 mm, table length: 3,000 mm, ZINSER 1225, CNC 6010 Year of manufacture: 2023 Arc height control ZAC 5070 with Hypertherm plasma system XPR 170 Core Plus Kjdpfx Apszwvx Io Dodu Cutting table 1,500 x 3,000 mm incl. extraction system Software available upon request.

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, type of input current: three-phase, sheet thickness (max.): 80 mm, sheet thickness aluminum (max.): 50 mm, input voltage: 400 V, total length: 13,000 mm, cutting current: 300 A, travel distance X-axis: 2,500 mm, travel distance Y-axis: 12,000 mm, type of cooling: water, Here is the sales listing translated into professional English: For Sale: Teknohaus Thermcut 4500 P Gantry Cutting Machine (Bevel Plasma & Oxy-Fuel) For sale: A modern, industrial-grade Teknohaus Thermcut 4500 P gantry cutting machine, manufactured in 2021. This system combines high-precision Hypertherm XPR300 bevel plasma technology with IHT Automation oxy-fuel cutting, offering a versatile range of cutting capabilities from thin sheet metal to heavy plate cutting and beveling. Key Specifications Manufacturer: Suomen Teknohaus Oy Model: Thermcut 4500 P Year of Manufacture: 2021 Supply Voltage: 3 x 400 V Dimensions & Capability Cutting Area / Table Size: 2,500 mm x 1,200 mm Bevel Plasma Capability: Enables direct cutting of weld preparation bevels (e.g., V, X, Y, and K bevels) directly from the plate. Equipment & Features Plasma Power Source: Hypertherm XPR300 (X-Definition technology, 300 A) Ksdozy I S Ejpfx Ap Dodu Oxy-Fuel Cutting: IHT Automation / GCE FIT+ torches with dedicated gas control panel (Preheat / Propane / Cutting / O₂) Control System: Modern CNC control unit with touchscreen and physical controls Safety Features: Emergency pull-wire safety system along the table sides and comprehensive safety labeling Cutting Capacity (Hypertherm XPR300) Mild Steel: Piercing up to 50 mm (Argon-Assist), Severance up to 80 mm Stainless Steel & Aluminum: Piercing up to 38 mm / Severance 50–75 mm The machine is in excellent working condition and has been well-maintained in an industrial production environment.

Condition: used, Year of construction: 2011, functionality: fully functional, For sale: 4 temperature control units by Plasma: Medium: water Temperature: max. 90°C Heating capacity: 9 kW Cooling capacity: 30 kW Alarm function Flow measurement Automatic water change function PT 100 sensor Interface for TTY 20 mA via 9-pin D-Sub connector Ksdpfx Apsx Ek Rds Djdu

Condition: excellent (used), For sale: Hypertherm Powermax 800 D plasma cutter in very good condition. /////Price stated is for 1 unit/////. Kdedpfjz Sb I Dex Ap Deu Hypertherm Powermax 800 plasma cutter Plasma cutter description: The Powermax800 plasma cutting system uses an inverter power supply to provide smooth DC output voltage, ensuring excellent cutting and grooving quality for mild steel, stainless steel, aluminum, and other metals. The Powermax800 power supply provides a constant output current with a variable range from 20 to 50 amps, ensuring optimal performance for all metal thicknesses up to 1/2 inch (12 mm). At 50 amps, the Powermax800 can cut metals up to 3/4 inch (20 mm) thick and pierce metals up to 1 inch (25 mm) thick.

Condition: used, Year of construction: 2021, SIDEROS ORION 2 table with scraper, year 2014. Table dimensions: 2600 x 12000 mm. New cutting head. MESSER MULTITHERM 4000 oxy-fuel cutting machine, year 2008. PROFIMEC external filter. Kdjdpjzw H Igjfx Ap Deu TO BE COLLECTED BY SEPTEMBER 2026.

Condition: used, Year of construction: 2017, functionality: fully functional, machine/vehicle number: 2202, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, type of input current: three-phase, input voltage: 400 V, input current: 50 A, Microstep Mastercut Eco Plus 3001.15 Year of manufacture: 2017 Control system: IMSNC Oxy-fuel cutting table: 3000 x 1500 mm Extraction duct left / right Plasma source: Kjellberg HiFocus 161i, adjustable 10 - 160 A Power source HiFocus 161i PLUS • Flexible adaptation of the cutting process to required conditions thanks to soft-switch inverter and microprocessor control • Optimal process control with ultra-fast regulation of cutting current • Process monitoring for torch cooling, ignition time, pilot arc time, short circuit time during torch ignition, and power source • Operating status and error display via LED and screen • Analog and serial interfaces for adaptation to CNC controllers • Infinitely adjustable cutting current from 10 - 160 A and during marking from 5 - 25 A • Optimal piercing through infinitely variable delay time for the main arc and adjustable current rise • Adjustable current reduction for cornering, start, and end signals of the guidance system • Automatic display of the preset cutting current • Serial data transmission for PC-based diagnostics Plasma cutting technology: Contour Cut • Further development of HiFocus technology for mild steel • Optimized for cutting fine internal and external contours • High cutting quality and contour accuracy • Holes with angular deviations according to DIN EN ISO 9013 range 2-4 • Minimal angular deviations and smooth cut surfaces • Excellent repeatability and dimensional accuracy • No tedious post-processing – high productivity and low costs • No additional equipment, software, or new consumables required • Standard equipment Plasma torch PerCut 200/210 • PerCut 200 plasma machine torch for standard applications and high-precision bevel cutting • Quick-change PerCut 210 torch with threaded lock for quick and convenient tool swapping • Special torches available for special applications • Higher cutting speeds reduce cost per meter • Long service life of consumables conserves resources • Narrower kerf means fewer emissions and less waste • Significantly lower gas consumption compared to competitors thanks to efficient liquid cooling up to the nozzle tip • Lower noise levels due to reduced gas consumption • Bevel cutting up to 50 degrees with standard consumables • Cutting and marking possible with the same consumables Kjdpfxey Nd Hys Ap Dodu Power source HiFocus 161i Power supply: 400 V; 3 Ph; 50 Hz Max. power input: 28 kVA (100% duty cycle) Main fuse, slow-blow: 50 A Protection class: IP22 Open circuit voltage: 330 V Cutting current: 10 – 160 A (100% duty cycle) Marking current: 5 – 25 A (100% duty cycle) Cutting range: Max. 50 mm Recommended: 0.5 – 38 mm Max. piercing thickness: 30 mm Weight: 206 kg Plasma machine torch PerCut 200 Quick-change torch PerCut 210 Clamping diameter: 50.8 mm Plasma gases: O2, N2, Ar/H2 Marking gases: Ar Swirl gases: O2, N2, Air, N2/H2 (F5)

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, total length: 9,000 mm, track width: 5,100 mm, table length: 6,000 mm, working width: 2,000 mm, ZINSER 4125 / CNC 6010 Track width: 5,100 mm, year of manufacture: 2024 Working width: 2,000 mm Working length: upon request Overall length: upon request 1 x CNC-controlled drilling unit MAX40R with 6-position linear tool changer Kdedpozw Et Uofx Ap Dju 1 x Hypertherm XPR300 CorePlus plasma system with plasma bevel cutting head 1 x Oxy-fuel torch including capacitive height control and ignition system Cutting table and extraction system: upon request Software: upon request

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, total length: 9,000 mm, track width: 3,100 mm, table length: 6,000 mm, working width: 2,000 mm, ZINSER 2425-I / CNC 6010 Track width 3,100 mm, year of manufacture 2024 1x Hypertherm XPR300 Core Plus plasma system with plasma beveling head 1x Oxy-fuel torch incl. capacitive height control and ignition system Kedpfx Apozw Eqmj Djdu Working length: customization possible upon request Software: available upon request Table and extraction system: available upon request

Condition: good (used), Year of construction: 2019, functionality: fully functional, Table surface: 7,500 x 2,500 mm Positioning speed: 40,000 mm/min Positioning accuracy: = 0.06 mm/min Repeatability: 0.05 mm/min Machine weight approx.: 2,300 kg MicroStep CNC cutting system of the MG series with the following features: Kjdpszwl Dmjfx Ap Djdu - Hypertherm® XPR170™ plasma power source with automatic OptiMix™ console - Plasma rotator for weld preparation - Fully automatic oxy-fuel torch - Fully automatic drilling spindle MG-40-P26 with 26.8 kW - Steel portal driven and stiffened on both sides for a clear and precise cut - AC servo motors from Panasonic for high drive power and excellent dynamics - Durable and low-maintenance planetary gearboxes - User-friendly machine control - High reliability and long service life, even in three-shift operation - MicroStep iMSNC® machine control with MMI console and 24" touchscreen - iMSNC® module | User management - iMSNC® module | Expert system - iMSNC® module | Automatic calibration of mechanical sensing - iMSNC® module | Visualization of wear parts - iMSNC® module | Assistant for loading CNC programs - iMSNC® module | Management of cutting programs (MRP) - iMSNC® module | EcoInfo - iMSNC® module | MachineInfo - iMSNC® module | Assistant for service and maintenance operations - USB 3.0 connection for storage media - Remote maintenance module MicroStep RemoteDiagnostics® - Remote maintenance access via TeamViewer - Two LCD control units on the portal - Laser pointer with automatic offset transfer - Hypertherm® XPR170™ plasma power source - Industry-leading cut quality - X-Definition - Advanced HyDefinition technology - Automatic gas console | OptiMix™ - CNC interface for the Hypertherm® XPR170™ Connection to the CNC control - Module for automatic power control of the Hypertherm® XPR170™ - Electrical and mechanical torch sensing - Remote activation of plasma power source - Double-sided cable protection (collision protection) of the portal bridge via emergency stop - Extraction table system with oscillating conveyor OXYtrac 2580 HD Main components and dimensions: 1 Table consisting of: 4 table elements WxLxH (mm) 2,600 x 2,080 x 950 Total support area: WxLxH (mm) 2,600 x 8,320 x 950 Contiguously usable working area per table: Vertical cutting: WxL (mm) 2,500 x 8,000 Bevel cutting: WxL (mm) 2,000 x 8,000 Table width (outer): W (mm) 2,830 2 Oscillating troughs L (mm) approx. 8,900 Cutting processes and associated extraction capacity: 1x Plasma max. 170 Amp., bevel cutting 1x Oxy-fuel max. 100 mm workpiece thickness regularly 200 mm workpiece thickness occasionally

Condition: good (used), Year of construction: 2008, Used 6000 x 2000 mm plasma cutting machine from HPM (Italy) Type: GV 60 20 Table dimensions: 6000 x 2000 mm Kdodszd Ur Tepfx Ap Dju Hypertherm 130 XD with Truehole option New Hypertherm EdgeConnect CNC control + new servo motors Modesta extraction system Includes spare parts Year of manufacture: 2008 CNC control renewed in: 2018

Year of construction: 2018, condition: like new (used), PlateExakt 600 - Cliché mounting device/die-cutting cylinder Ksdpfxjl Ax Uwo Ap Djdu  Age: 1992  Mounting device  cliché mounting device which is exclusively designed to, the cliché or the die-cutting plate onto the impression or die-cutting cylinder safely, precisely and quickly cylinder. The device has two high-resolution USB cameras that can be moved linearly on a precision guide. precision guide. Synchronised via the centre and individually adjustable by means of a handwheel for different printing widths.  Max. diam.: 227”  Min. diam.: 60”  Width: 620mm

Condition: used, functionality: fully functional, USED PLASMA CUTTING TABLE CR ELECTRONIC 8x2.5 M WITH HYPERTHERM HT2000 LHF GENERATOR, OVERHAULED "CE" Kjdpfxjzhutre Ap Dedu

Condition: good (used), Year of construction: 2007, functionality: fully functional, type of input current: three-phase, working range: 3,000 mm, sheet thickness (max.): 40 mm, The information was found successfully. Here is the updated listing with added cutting parameters: Teknohaus Thermcut 3000D – CNC Plasma Cutting Machine For sale: a well-maintained Finnish-made CNC plasma cutting machine. The machine has been used in production and operates flawlessly. Technical specifications: Manufacturer: Suomen Teknohaus Oy Model: Thermcut 3000D Year of manufacture: 2007 Serial number: 320011 Supply voltage: 3 × 400 V Plasma source: Hypertherm HyPerformance HPR130 (130 A) Controller: Thermcut / Teknohaus CNC controller with touchscreen Kdjdpfsywlh Uox Ap Dju USB interface for program transfer Cutting capacity (mild steel): - High-quality, virtually dross-free cut: 16 mm - Production piercing: 25 mm - Maximum cutting thickness (edge start): 38 mm Features: - Large cutting table (approx. 3000 mm wide) - Two plasma channels (Plasma 1 & Plasma 2) - Water table for spark and fume management - Ideal for cutting steel, stainless steel, and aluminium Machine viewings available by appointment; the machine can be seen in full working order. 📞 For further information, please call.

Year of construction: 2010, condition: ready for operation (used), Max. sheet dimensions: 6050x2550mm, max. cutting speed: 10m/min, length: 8125mm, width: 3800mm, height: 1900mm, with documentation, an on-site inspection is possible. Ksdpfx Ajri Skasp Dsdu

Condition: used, Year of construction: 2010, functionality: fully functional, working range: 6,000 mm, sheet thickness (max.): 50 mm, sheet thickness aluminum (max.): 35 mm, overall weight: 4,000 kg, working width: 2,000 mm, travel distance X-axis: 6,000 mm, type of cooling: air, Equipment: documentation/manual, Used MicroStep flame cutting machine (plasma system) SPL 6001.20 P with Kjellberg torch. Used, fully functional. Kdodpfx Apezr D Hpo Dou Extraction system included. Video demonstrating the machine in operation is available; please contact us if you are interested or have any questions. Price negotiable.

Condition: ready for operation (used), Year of construction: 2017, functionality: fully functional, machine/vehicle number: Aventa PLUS 4 x 2, type of input current: DC, working range: 40,002,000 mm, sheet thickness (max.): 30 mm, sheet thickness steel (max.): 25 mm, sheet thickness aluminum (max.): 25 mm, cutting current: 300 A, Equipment: documentation/manual, Macchina in operazione Kdedpfxow Al Rme Ap Deu

Condition: used, functionality: fully functional, machine/vehicle number: 11.031.802, Plasma Cutting & Grooving with Hand Torch, from 3 to 45 mm Simple and cost-effective technology for any cutting application The PA-S45 W plasma cutting system is suitable for manual and mechanized cutting in the material thickness range of 3 to 45 mm. By using different plasma gases and gas mixtures, electrically conductive materials can be cut and grooved cleanly. As a mobile system, it can be used in workshops, training centers, and on construction sites. Advantages: Kdodpfsy U Uqtex Ap Dsu Optional use of hand or machine torch Suitable for 2D & 3D guidance systems Robust and simple design Mobile systems for flexible use Reliability even under difficult production conditions Cutting current can be pre-selected in three stages Effective cooling of the plasma torch and its wear parts Quick changeover from cutting to plasma grooving and vice versa Angled torch heads and special shank designs for optimized cutting of 3D parts Wide range of applications thanks to optional equipment Liquid-cooled plasma torches The proven design of the torch components, cathode, and nozzle, is a prerequisite for the quality of the cut surfaces. The liquid cooling of the plasma fine-jet torches guarantees their long service life. Plasma cutting with the systems in the PA-S series is therefore efficient and increases the user's productivity. When cutting construction steel with the PA-S45 W, a swirl gas torch often allows for more frequent piercing. Plasma Grooving Both machine and hand torches can be quickly converted for plasma grooving. This requires changing the nozzles and attaching the ceramic cap (if necessary, with a protector). By using different plasma gases and gas mixtures, all electrically conductive materials such as construction steel, stainless steel, aluminum, and brass can be processed. Plasma grooving is ideally suited for removing welding defects, cracks, porosity, and inclusions, as well as for preparing for counter-welding. Advantages: No carbonization of the material No post-grinding required Low heat input Good observation of the process Reduction of noise levels and smoke generation

Condition: used, Year of construction: 2012, Plasma power source for plasma cutting system Manufacturer: Kjellberg Kdjdpfxoz Ipnus Ap Deu Type: HiFocus 440i Year of manufacture: 2012 Automatic gas control unit Includes cooling unit KWE360 Includes hose package with torch and cable 191026ä

Condition: new, Year of construction: 2019, functionality: fully functional, machine/vehicle number: PR4-3000-05190216, sheet thickness (max.): 25 mm, sheet thickness aluminum (max.): 20 mm, input voltage: 400 V, cutting current: 105 A, input current: 28 A, input frequency: 60 Hz, electrical fuse: 50 A, open-circuit voltage: 292 V, Swift-Cut Pro 3000 CNC Plasma Cutting System Kdjdpszvch Tsfx Ap Deu Complete new and unused CNC plasma cutting system from Swift-Cut Automation, manufactured in 2019. The machine has never been used and is equipped with a Hypertherm Powermax105 plasma power source and an ECO 4 HC/S dust extraction unit with a spark trap. The dust extraction system is suitable for plasma cutting applications, including aluminum cutting. Main specifications: Manufacturer: Swift-Cut Automation Model: Pro 3000 Year of manufacture: 2019 Condition: New, never used Serial number: PR4-3000-05190216 Cutting area: 3000 × 1500 mm Plasma power source: Hypertherm Powermax105 Plasma cutting current: 30–105 A Power source: 380/400 V, 3-phase, 50–60 Hz Power source P/N: 059412 Dust collector: ECO 4 HC/S Dust collector motor: 5.5 kW Dust collector power supply: 400 V / 50 Hz Dust collector application: Plasma cutting up to 120 A Additional equipment: Spark trap / spark separator The Hypertherm Powermax105 provides high-performance plasma cutting for a wide range of conductive materials. The actual cutting capacity depends on the material type, thickness, and cutting conditions. The ECO 4 HC/S dust extraction unit is designed for plasma cutting applications and is equipped with an additional spark trap. Its configuration also allows aluminum to be cut safely with suitable operating conditions. Please note: The system is offered without a compressor. A suitable source of clean, dry, and oil-free compressed air is required for the operation of the Hypertherm Powermax105.