Used Punching And Bending Machine for sale (68,553)

Condition: used, Single-column eccentric press RICHTER type PEKRS 80 Year of construction 1970 - overhaul 2024 Compressive force 80 ton. throat depth 350 mm Table size 900 x 650 mm Hole in the clamping table Ø 200 mm ram surface 700 x 500 mm Stroke rate 70 strokes/min. Stroke adjustment 6 - 100 mm ram adjustment 85 mm Installation height max. 400 Clamping pin bore Ø 50 mm Table height above floor 810 mm Motor power 8 kW Mains connection 400 Volt, 50 Hz - ORTLINGHAUS pneumatic clutch/brake combination - HERION XSz 32 press safety valve - Pneumatic ram compensation cylinder - Overload protection with breaker plate in ram - Central grease lubrication with hand pump Space requirement L x W x H 1800 x 1250 x 2830 mm Weight 5.7 tons Very good condition Technically overhauled and converted to the latest UVV with new electrics Control conversion in 05/2024 - suitable for manual insertion work - in accordance with DGUV Information 209-030 Press inspection Bdodoi Db Ibspfx Abwjc and Machinery Directive 2006/42/EC Low Voltage Directive 2014/35/EU EN ISO 16092-1: Safety of machine tools - Presses - Part 1: General safety requirements EN ISO 16092-2: Machine tools - Safety of presses - Part 2: Mechanical presses - Control system with plain text error messages and diagnostic screen for rapid fault localization - New electrical cabinet, mounted on the side of the machine - completely based on SIEMENS, with PLC S7-1200 PROFIsafe and 7" TFT touch display - Two-hand control panel with emergency stop and engagement lock - el. foot switch - Cam switch unit with run monitor control - Stroke release via HERION XSz 32 press safety valve with pneumatic pressure compensator - New wiring of the machine - Updated operating instructions The machine is equipped with 6 operating modes: 1 = Set-up 2 = Single stroke two-handed 3 = Single stroke foot 4 = continuous run foot 5 = automatic continuous run 6 = reverse run

Condition: used, Semi-automatic tube bending machine, mandrel tube bender MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Serial No. Year of construction for simultaneous bending of two steel tube sections up to Ø 12 mm Bending angle max. 90° Tube diameter max. 12 mm Mandrel length approx. 65 mm Rated power 3.5 kW Compressed air max. 6 bar / approx. 1 litre per bending cycle Power supply 400 Volt, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Angle input control via STÖBER Controlbox Series 4000/5000 - SIEMENS S7-200 control with TD200 display Bdsdpjpu R Nvjfx Abwsc - Machine without bending tools and without tool storage pins 25 x 183 mm - Only 1 bending mandrel available (see pictures). Required space (L x W x H) 1000 x 1000 x 1500 mm Weight 390 kg Good condition

Year of construction: 2008, condition: ready for operation (used), X-axis: 2500mm, Y-axis: 1270mm, positioning speed X-axis/Y-axis: 80/90m/min, simultaneous axis speed: 100m/min, punching capacity: 200kN, number of turret stations: 51, max. material thickness mild steel: 3.2mm, max. material weight at traverse speed F1/F4: 50/150kg, positioning accuracy: ±0.1mm, stroke rate X-axis: 350/min, stroke rate Y-axis: 260/min, max. stroke length: 42mm, max. feed speed X-axis/Y-axis: 80/60m/min, turret speed: 30rpm, compressed air requirement: 500l/min, operating air pressure: 5bar, connected load: 19kVA, length: 4165mm, width: 5120mm, height: 2082mm, height with mirror: 3028mm, weight: 13t, operating hours: 4531h, regularly maintained by the manufacturer, with documentation, without punching tools. An on-site inspection is possible. Bsdpfxoza E S Ds Abwodc

Condition: used, Year of construction: 1993, 3 Rollers Bending Machine ZOPF TRENNJAEGER RS 302 ME Bdodsza Eynepfx Abwsc Year of construction: 1993 Capacity: 1/4'' to 1 1/2'' - Ø 10 mm to Ø 60 mm Rectangular tube 50 x 30 x 3 Square tube 40 x 40 x 3 (see description on photo) Delivered with: 1 set of rollers 1'' - 6/4'' - 1 1/4'' + various (see photos) Voltage: 380 V Dimensions (L x W x H): 1000 x 1000 x 1600 mm Weight: approx 200 kg

Condition: good (used), Year of construction: 1979, total height: 1,750 mm, total width: 800 mm, total length: 1,200 mm, sheet thickness steel (max.): 3 mm, working range: 960 mm, overall weight: 750 kg, power: 0.37 kW (0.50 HP), Copy nibbler PIONIER KNA 600, steel capacity 3 mm, circular nibbling up to Ø 1000 mm, throat depth 600 mm, throat height 90 mm, motor 0.3 kW, stroke 0-12 mm, dimensions 1400x800x1750 mm, weight 400 kg Bdodpjyq Sc Dofx Abwjc

Condition: good (used), Year of construction: 1979, total height: 1,805 mm, total width: 1,700 mm, total length: 2,090 mm, sheet thickness steel (max.): 3 mm, working range: 960 mm, overall weight: 1,200 kg, Copy nibbling machine PIONIER K 1200/6, steel capacity 6 mm, circular nibbling up to Ø 500 mm, throat depth 1220 mm, throat height 200 mm, working length 960 mm, motor 1.3 / 2.2 kW, stroke 10 mm, dimensions 2090x1400x1800 mm, weight 1200 kg, operating manual Bdedpfxsyq Savs Abwoc

Year of construction: 2024, condition: new, MRB-S Series Technical data (see pictures) Standard equipment CE Conical bend Motorized back roller Additional control panel for upper and lower rollers which are operated with landing gear. SAE 1050 steel rollers Induction hardened rollers, Relaxed steel construction, at 2.5 and 3m Machine supports, brake system for precise bends, Digital display. Motorized back roller with puller Optional equipment Motorised under-roller mounting, ground rollers Extended rolls for profile bends, Special rollers for profile bending, Special packaging for international deliveries. MRB series: Technical data (see pictures) Standard equipment CE standard Digital display Conical bend Motorized back roller with tightening Additional control panel for upper and lower rollers, which are operated with landing gear. operated by landing gear. SAE 1050 steel rollers, Induction hardened rollers, Relaxed steel construction, Braking system for precise bends. Optional equipment Motorized bottom roller with suit, stone rollers Bjdofin E Djpfx Abwsdc Extended rolls for profile bends, special rollers for profile bending, Special packaging for international Programmes Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Durma Maschinen GmbH is part of the internationally successful Durmazlar Group, which exports new, high-quality sheet metal working machines all over the world and is headquartered in Türk

Year of construction: 2024, condition: new, Bending capacity: 6 mm Bending: 5 mm Bending capacity: 6 mm Bjdpfoftdh Isx Abwsdc Bending: 5 mm Bending length: 2,030 mm roller diameter: 170 mm Engine power: 4 kW Length: 3.600 mm Width: 1,020 mm Height: 1.120 mm Weight: 2.400 kg The machine can be viewed and demonstrated at any time by appointment in our demonstration centre in Staufenberg. Further machines are ready for demonstration at our premises in Staufenberg. We will be happy to provide you with further information on request.

Year of construction: 2024, condition: new, Control unit - with NC control Conical bending device Side roll positioning electronically synchronized via PLC Safety mechanism for welding (welding possibility) on the machine Machine body made of stress-relieved annealed steel 4 roll drive system - upper, and lower roller with hydraulic motor driven synchronized via planetary gear (ᐳ 430 mm) Electrical and hydraulic protection against overloads Hydraulically adjustable lower roller pressure Hydraulic roller brake, prevents the sheet from slipping back Hydraulic swinging out of the upper roller bearing, for easy removal of the formed sheet Safety wire Induction-hardened rollers (HRC 54), crowned ("crowning"). Variable speed Bending length: 2050 mm Bending capacity: 13 mm (d x 5) Bending capacity: 10 mm (d x 1.5) Top roll: 230 mm Bottom roll: 210 mm Maximum roll width: 30 mm Length: 3830 mm Width: 1160 mm Height: 1200 mm Motor power: 11 kW Weight: 4700 kg Bodedzzyfjpfx Abwsdc

Condition: good (used), Year of construction: 1991, 3-roll plate bending machine Plate width: 3000 mm Plate thickness: 20 mm Pre-bending: 16 mm Top roll diameter: 380 mm Bodpfx Aoza A R Rebwjdc Side roll diameter: 340 mm

Condition: good (used), Year of construction: 2005, control type: CNC control, pipe diameter (max.): 30 mm, Tube diameter: 30 mm Wall thickness: 2 mm Max. bending angle: +/- 180 + 10 ° Tube insertion length: 4100 mm - Round steel tube up to 30 x 2.2 mm² - Round stainless steel tube up to 30 x 1.5 mm - Square tubes 20 x 2.5 mm - Bending time for 90 degrees: 1.5 sec. (feed) - Longitudinal feed speed: 450 mm/sec. Bdedpsza A Hrsfx Abwsc - Maximum bending radius: 125 mm - Freestanding bending head, 850 mm long - Bending axis drive: electrohydraulic

Condition: excellent (used), Year of construction: 2013, controller manufacturer: ELFRAN Digital Read Out, number of rollers: 3, shaft diameter: 130 mm, overall weight: 5,800 kg, total length: 2,200 mm, total width: 2,400 mm, total height: 2,000 mm, Profile bending machine FACCIN - RCMI 130 MACH-ID 9451 Make: FACCIN Type: RCMI 130 Control: ELFRAN Digital Read Out Year: 2013 3 rolls driven 2 lateral guide rolls Digital readout for position rolls Set hardned universal rolls Set hardned profile rolls Horizontal and vertical:|Horizontal and Vertical Shaft Ø: 130mm Number of rolls: 3 Bdjdpeyrq Dvefx Abwec Capacity flat: 240 x 30 x 1000mm Capacity Tube: 140 x 5 x 1500Ø x mm Capacity bar: 80 x 80 x 900mm Capacity T-Profile: 140 x 15 x 1400mm Capacity HEA-Profile: 160 x 1700mm Working speed: 0 - 6000mm/min. Side supports: 2 x Hydraulic side arms Length: 2200mm Width: 2400mm Height: 2000mm Weight: 5800kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1999, overall weight: 2,900 kg, total length: 1,800 mm, total width: 1,900 mm, total height: 2,200 mm, Length:1800mm Width:1900mm Height:2200mm Weight:2900kg Bedpfx Ajycu E Esbwodc

Condition: good (used), profile bending machine Bsdpowtph Defx Abwsdc

Condition: excellent (used), Year of construction: 2008, control type: CNC control, controller manufacturer: ESA TOUCH PANEL, pipe length (max.): 4,000 mm, bending radius (max.): 180 mm, bending radius (min.): 10 mm, overall weight: 3,700 kg, total length: 6,000 mm, total width: 1,800 mm, total height: 1,800 mm, Tube bending machine Transfluid - DB630 A3 CNC MACH-ID 9616 Make: Transfluid Type: DB630 A3 CNC Control: ESA TOUCH PANEL Year: 2008 Max.Tube Ø: 30mm Min. Tube Ø: 4mm Max. Wall thickness:4mm Max. Bending radius:180mm Min. Bending radius:10mm Max. bending length:4000mm 3e dimsion bending:Yesmm/min. Number of tools: 10,12,15,16,18,20,22,28 Length: 6000mm Bjdpfxey N Rv Is Abwodc Width: 1800mm Height: 1800mm Weight: 3700kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Manufacturer: Tracto Technik Type: TUBOMAT Year of construction: 1996 Pipe bending machine with electric control, 4-fold bending angle pre-selection and digital display Hydraulic bending drive operated by hand lever valve Hydraulic bending drive, operated by hand lever valve Follower-type pressure die (sliding guide) Hydraulic mandrel retraction Pipe circular saw with coolant lubrication and automatic feed Pipe deburring unit for internal and external deburring Hydraulic power unit as basic seating for attaching a cutting ring assembly or flaring device Machine mobile and flexible to use Specifications Metric US Standard Max. Product Ø 42 mm Min. product Ø 6 mm Max. Wall thickness 3 mm Max. Bending radius 5 mm Min. bending radius 180 mm Max. Bending length 2000 mm Deburring device Yes Sage device Yes Flanging device Yes Dimensions (estimate) Length 3500 mm width 1000 mm height 1200 mm Bdsdpfx Aet Dk Ukjbwec weight 1000 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: excellent (used), functionality: fully functional, Year of construction: 1989, pipe diameter (max.): 42 mm, pipe length (max.): 3,000 mm, bending radius (max.): 180 mm, wall thickness: 3 mm, Pipe bending machine with electric control, 4-fold bending angle pre-selection and digital display  Hydraulic bending drive operated by hand lever valve Hydraulic bending drive, operated by hand lever valve Follower-type pressure die (sliding guide) Hydraulic mandrel retraction Pipe circular saw with coolant lubrication and automatic feed 6 mandrels up to 24 mm included x 3000 mm Pipe deburring unit for internal and external deburring Hydraulic power unit as basic seating for attaching a cutting ring assembly or flaring device  Machine mobile and flexible to use Max. tube Ø: 42mm Min. tube Ø: 6mm Max. Wall thickness: 3mm Max. Bending radius:5mm Min. bending radius:180mm Max. bending length:3000mm Deburring attachment:Yes Sawing attachment: Yes Bdsdpjuccw Hefx Abwjc Flair attachment: Yes Length: 3500mm Width: 1000mm Height: 1200mm Weight: 1000kg

Condition: good (used), Year of construction: 2022, Adjustable stroke with digital read out positioning display Variable adjustable pressure Quick change tool system Table length: 1250 mm Table width: 660 mm Max. working pressure: 30 tons Max. stroke: 235 mm Max. workpiece weight: 250 mm Stroke adjustable: 0 - 235 mm Working speed: 10,000 mm/min Return speed: 20,000 mm/min Power: 3 kW Flat capacity: 200 x 24mm x mm Tube capacity: 60 x 4Ø x mm Solid capacity: 40 x 40mm Length: 1250 mm Width: 700 mm Bsdowrzmvopfx Abwjdc Height: 1200 mm Weight: 1050 kg

Condition: good (used), Year of construction: 2018, Manufacturer: INDUCTAFLEX Type: AL-3e Control system: ACCURATE touch screen Year of construction: 2018 3 rolls driven servo Torq each roller 3500 nM Electrically support rolls Bdedpfx Aevd Dftjbwsc Intelligent software : Ellipse program U Bend shapes control of tangents Auto section detector Specifications Metric US Standard Horizontal and Vertical Horizontal Axis Ø 105 mm Number of rollers 3 Stroke X axis 0 - 400 mm Dimensions (estimate) length 4500 mm width 3200 mm height 2700 mm weight 3300 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: used, total length: 1,000 mm, total width: 750 mm, total height: 1,400 mm, Colour: Grey Empty weight: 400 kg - Documentation available: No - CE certificate present: No - Drive system: Conventional - Number of rolls [pcs.]: 3 Bdedpfxoypk Ebj Abwsc - Number of driven rolls [pcs]: 3 - Power [kW]: 1.5 - Shaft diameter [mm]: 50 - Moment of resistance [cm³]: 6 - Top roll diameter [mm]: 50 - Bottom roll diameter [mm]: 50 - Capacity diameter round [mm]: 35 - Transport dimensions: 1000mm x 750mm x 1400mm (l x w x h) - Transport weight [kg]: 400kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1988, gebraucht 1988 090151 prompt, Zwischenverkauf v Italien 12800 € 1 42 mm 4665 mm 800 mm 1160 mm Bdodpsxx A Ekjfx Abwsc 1470 kg 42 x 2,5 mm 40 x 1,2 mm 30 x 40 x 1,7 mm 40 x 30 x 1,3 mm 255 mm 22 mm 180 ° 90 °/s 5.5 kW 120 l Capacity specifications refer to 400 N/mm² Maximum bending radius with pipe guide rollers: 255 mm Maximum bending radius with pipe guide slide: 175 mm Minimum bending angle: 4° Maximum usable length without positioning device: 3900 mm Maximum usable length with positioning device: 3370 mm Adjustable mandrel extension travel from 8 mm Opening and closing travel of the counter-clamping jaws: 0-45 mm Opening and closing travel of the rollers or slides: 12-22-42 mm Operating manual in German Machine does not comply with AMVO or UVV regulations Tools not included BUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISE We offer you maximum security and complete transparency. • HONEST INSIGHTS: Detailed photos and functional videos of the current condition • LIVE ON-SITE CHECK: Live testing is possible at our facility • DIGITAL DEMONSTRATION: Individual live demonstration via video call • RISK-FREE PURCHASE: 14-day return policy Details:

Condition: new, functionality: fully functional, Year of construction: 2021, For sale: Brand new, never-used DAVI bending machine. *MAIN FEATURES MCP 18* Bsdpfxey N Rbws Abwodc *1. Type and Capacity* - *3 hydraulically driven rollers*, pyramid configuration - *Shafts Ø 180 mm* → this is the "18" in MCP 18 - *Bending*: round, square, rectangular tubes, angles, flat bars, UPN, IPE, HEA... all b235 profiles *2. Indicative capacities on MCP series* DAVI does not provide the exact MCP 18 datasheet online, but for the equivalent MCP range: Profile Approx capacity MCP 18 Round tube Ø 6" to 8" depending on wall thickness Solid square 80x80 mm to 100x100 mm Angle 120x120x12 mm UPN UPN 200 - 240 IPE flat flange IPE 200 - 240 Actual figures depend on wall thickness and steel grade. The 18 cm Ø shafts make this a mid/high-category machine. For all available options, please refer to the photo in the listing.

Year of construction: 2003, operating hours: 69,600 h, condition: used, functionality: fully functional, Used TRUMPF-PULZER CNC35L tube bending machine We are offering a used TRUMPF-PULZER CNC35L tube bending machine for sale. Technical data: Manufacturer: TRUMPF-PULZER Type: CNC35L Machine No.: 837 Year of manufacture: 2003 Electrical connection values: Voltage: 400 V / 3~ Frequency: 50 Hz Current consumption: 21 A Connected power: 14 kVA Bending capacity: Bending direction: Left-hand Suitable for tubes made of steel, stainless steel and non-ferrous metals Maximum tube dimensions: Ø 35 x 2 mm with a bending radius of R = 2 x D Tube feed length: approx. 3,000 mm Equipment: Mandrel bending device Dimensions and weight Installation dimensions (L x W x H): approx. 5,550 x 2,520 x 1,560 mm Machine weight: approx. 2,500 kg Bjdszaqm Tspfx Abwedc Description: The TRUMPF-PULZER CNC35L is a robust and proven CNC tube bending machine for the precise processing of steel, stainless steel and non-ferrous metal tubes. Thanks to the integrated mandrel bending device, the machine is particularly suitable for demanding bending tasks with high quality requirements. The machine dates from 2003 and is offered in used condition. If you are interested or would like further information, please do not hesitate to contact us. Inspections are possible by arrangement.

Condition: used, functionality: fully functional, Year of construction: 1993, machine/vehicle number: 4422559493014, Equipment: CE marking, Peddimax 600 Equipment - Flat, profile, and bar steel shear - Notching & punching unit 600 kN - Mechanically adjustable profile and flat steel hold-down device - Quick-change punch system Punching table Bodpfx Aberknnfjwedc - Universal punch saddle - Material support table for notching device - Various punches and dies

Condition: used, functionality: fully functional, Heavy-duty 3-roll pipe bending machine for round bending of steel pipes and profiles into rings, circular arcs, or spirals. Classic design with grooved pressure rollers (several diameters visible) and a sturdy base – very stable. The number of grooves allows bending of different pipe diameters without retooling. Suitable for heating construction, plant engineering, steel construction, railing construction, and blacksmithing. Such machines are becoming rare on the used market – the new price of comparable equipment is often a five-figure sum. Bsdpszab Hqsfx Abwjdc Technical data: - Design: 3-roll pipe bender (profile ring bending machine) - Drive: manually operated or motorized (to be checked on-site) - Rolls: with several grooved profiles - Construction: heavy steel housing on a base - Inventory No.: 500005 - Weight: approx. 300-600 kg - Year of manufacture: approx. 1970s-1980s Collection/Transport: Self-collection with forklift/crane. Loading on-site is possible. Shipping via freight forwarder on a pallet can be arranged.