Used Punching And Bending Machine for sale (69,156)

Condition: good (used), Year of construction: 1985, FOR SALE: Automatic Stamping and Bending Machine BIHLER RM-30 High-performance equipment for the automatic production of complex metal parts from wire or strip material. Identification and Brand Brand: BIHLER (Otto Bihler Maschinenfabrik, Germany). Model: RM-30. Year of manufacture: 1985. Machine number: 23589. Technical Specifications (Model RM-30) Maximum strip width: 32 mm. Maximum wire diameter: 3 mm (mild steel). Feed length (standard): Up to 120 mm. Nominal press force: 70 kN (7 tons). Production speed: Adjustable, up to 350 parts/minute (depending on complexity). Number of slides: Up to 5 standard bending units. Equipment and Configuration Control system: Separate control panel with user interface. Kinematics: Radial cam drive for maximum precision and repeatability. Press unit: Integrated for cutting, punching, or marking operations prior to bending. Iijlhcoy Shgpocqkjb Safety: Machine equipped with protective guards and emergency stop. Advantages Versatility: Enables the production of highly complex parts in a single cycle. Bihler reliability: Renowned worldwide for robust construction and long-lasting mechanical components. Precision: Ideal for the electronics, automotive, and connector industries.

Condition: good (used), Year of construction: 2002, functionality: fully functional, punching force: 20 t, TECHNICAL DETAILS Ijlhcjy Symuecqkoib Machine capacity: 200 kN (20 t) Air pressure: 5 bar Air flow rate: 250 Nl/min Oil capacity: 160 l Turret speed: 25 rpm Travelling ranges: Machine travel range without repositioning: 1,250 mm x 2,100 mm Processing Max. sheet thickness with ball bearing table: 6 mm Max. sheet thickness with brush table: 3 mm Max. weight per table: 100 kg Accuracy Punching accuracy (in standard mode): ±0.1 mm Positioning accuracy (repeatability): ±0.07 mm Performance Strokes per minute, feed 25.4 mm: X320 / Y250 Nibbling cycle, feed 1 mm: X920 / Y920 Tools Minimum programmable step: 0.01 mm Number of tools: 31 Max. tool diameter: 88.9 mm Dimensions (L x W x H): 4,890 x 4,370 x 2,137 mm Machine weight: 11,500 kg Note: No tools included, special transport required.

Condition: good (used), Year of construction: 2000, For sale is a used punching and bending center from Salvagnini. The S4 P4 is functional and ready for use. • Symmetrical bending unit Type: GPS Automatic device for precision bending Iijlhccsh Dwqhjqksb • Programmable blank holder Type: PB.U12 Consists of a device for automatically setting the length of the blank holder tool and a segment set for the blank holder tool • Panel delivery device/buffer SAP2220.POS Motorized roller table with dimensions of 3000 x 900 mm • Software Type: JOBS4P4.DIARIO Automatic batch size management (JOBS4P4), recording of data and movements of system components (DIARIO) • Control and management system Type: MMACHNT-MICROMach CPU processor: PENTIUM INTEL II 400 MHz Operating system: WINDOWS NT Subject to change/errors in technical specifications and subject to prior sale.

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, pressing force: 32 t, working height: 200 mm, controller model: Siemens 840D, working length: 2,150 mm, TECHNICAL DETAILS Ielhcsy D Ihwscqkjib Bending length: 2,150 mm Maximum bending height: 200 mm Minimum length/width between bends: 160–350 mm Pressing force: 32 t MACHINE DETAILS Control: Siemens 840D Dimensions & Weight Dimensions (L x W x H): 8,500 x 7,000 x 2,850 mm Weight: 30,000 kg EQUIPMENT Automatic tool changer Manipulator Reverse bending cycle Sheet centering system Additional top tools Loading and unloading system

Condition: good (used), Brand Boschert Model EL 500 Digital Year of construction 2009 Press force 28 tons Throat depth 180 mm Punching capacity 40 mm in 6 mm Worktable size 500x1000 mm Number of strokes 180 pcs Ielhccew Hyc Soqkjib Dimensions 2400x1580x1540 mm Weight 2000 kg Power 5 kW

Condition: excellent (used), Year of construction: 1989, functionality: fully functional, pressing force: 30 t, We offer this very good Bihler GRM 80 punching and bending machine, year of construction 1989. with 5 slides, 30T press, straightener, feeder with decoiler Tooling is not included If you have any questions or need more information, feel free to send us a message or give us a call. Ijlhceywty Eecqkeib

Condition: ready for operation (used), Year of construction: 2017, operating hours: 3 h, functionality: fully functional, pressing force: 20 t, working width: 1,250 mm, travel distance Y-axis: 1,270 mm, sheet thickness (max.): 6 mm, working length: 1,250 mm, No minimum price – guaranteed sale to the highest bidder! Machine from a training workshop with only 3 hours of punching time! Submission of a bid obligates timely collection by 21/11/2025! TECHNICAL DETAILS Pressing force: 200 kN Maximum sheet thickness: 6 mm Turret stations: 51 Auto-index stations: 4 Y-axis travel: 1,270 mm Working area: 1,250 x 1,250 mm MACHINE DETAILS Control system: AMNC-F Weight: 12,500 kg Electrical data Full load current: 55 A Short-circuit current: 25 kA Power consumption: 19 kVA Nominal voltage: 200 V Frequency: 50 Hz Iolhsxn Rvieccqkoib Operating hours Punching time: 3 h Power-on time: 895 h EQUIPMENT Solution Pack Blank School offline software AP100 2D CAD Production Designer 3D VPSS3i Blank Tooling package valued at EUR 8,000

Condition: excellent (used), Schroeder & Bauer WB 32-1 Universal Wire and Strip Bending Machine Wire Feeder Plain Text Display Press Force Monitoring Wire Straightener Bosch Stripping Machines Bracket and Brush Motor with Mounted W32/1-32 Tool Soundproof Cabin Drums of Copper Wire with Stamped Parts Iijlhcog T S Tascqkjb Control Cabinet Item Condition: Very Good Manufacturer's Description, Deviations Possible. You are purchasing the machine as shown in the pictures. Complete factory closure, large selection of storage platforms, pallet racks, shelving units, and paternosters. High-quality industrial machines, lathes, grinders, and hand tools. Financing through our bank is also possible. komplett-konzept.leasingo.de Find more items - new and used - in our shop! International shipping costs upon request!

Condition: excellent (used), Schroeder & Bauer WB 32-1 Universal Wire and Strip Bending Machine Wire Feed Plain Text Display Press Force Monitoring Iolhcceg T S Tdoqksib Wire Straightener Bosch Stripping Devices Bracket and Brush Motor with Attached W32/1-32 Tool Soundproof Cabin Barrels of Copper Wire with Punched Parts Control Cabinet Technical Specifications: Drive Power: 7.5 kW Speed (min. - max.): 40-250 rpm Press force / punching unit: 200 kN Longitudinal feed: 250 mm Longitudinal strip width: 50 mm Wire diameter: 6.0 mm Machine weight: 3500 kg Dimensions without electrical components (L x W x H): 3600 x 1500 x 2400 mm Item condition: very good Manufacturer's description, deviations possible. You are purchasing the machine as shown in the pictures. Complete factory closure, large selection of storage platforms, pallet racks, shelving units, and paternosters. High-quality industrial machines, lathes, grinders, and hand tools. Financing through our bank is also possible. komplett-konzept.leasingo.de You can find more punching and bending machines - new and used - in our shop! International shipping costs upon request!

Condition: excellent (used), Year of construction: 2006, Bihler RM 40E stamping and bending machine Compact machine system for the production of stamped and bent parts from strip and wire. Quick tool clamping system User-friendly P CNC 4E machine and process control Compatibility with RM 35, RM40, and RM4 tools Item condition: very good Manufacturer's description, deviations possible. You are purchasing the machine as shown in the pictures. Type: RM 40E No. 27907 Year of manufacture: 2006 1x 184-01-0022.0 Basic machine RM 40 including central lubrication and pneumatic system including P-CNC 4E control Ielhccqeg Inzkjkjib according to installation plan 184-00-0085.3 including tool: 484 0027 2x 142-04-0347.0 Wide slides (items A9 and A16) 1x 142-55-0007.0 Angle lever unit with right lever (item A7) Without feeder, press, and center punch including light barrier for personnel protection Financing through our bank is also possible. komplett-konzept.leasingo.de You can find more items - new and used - in our shop! International shipping costs on request!

Condition: ready for operation (used), Year of construction: 1979, Two Bihler GRM-50 are available, year of manufacture: 1979/1987. Feed length: 320mm, max. strip width: 40mm, wire diameter range: 0.5-5mm, center punch stroke: 52mm, max. production speed: 132 pieces/min. Dimensions X/Y/Z: approx. 2600mm/1500mm/1900mm, weight: approx. 3500kg. Iiolhstvar Ieccqkeb

Condition: used, Year of construction: 2007, Amada punch press EMK 3610NT including MP300 loading unit for sale. We would like to sell the machine as a complete package with tooling and a Wilson X-Sharp grinding machine. Iolhjw Hww Heccqkoib The standard tools are listed in the attached inventory. I can send it to you via email.

Condition: excellent (used), Year of construction: 1986, plate thickness 5 mm sheet width 40 mm Ijlexzk I Sehccqkeib

Condition: ready for operation (used), Year of construction: 1987, operating hours: 70,000 h, functionality: fully functional, machine/vehicle number: 21104, working range: 250 mm, feed length X-axis: 170 mm, overall weight: 1,600 kg, total height: 1,860 mm, pressing force: 7 t, total length: 2,000 mm, total width: 2,500 mm, table width: 184 mm, input frequency: 50 Hz, input voltage: 400 V, input current: 8 A, compressed air connection: 6 bar, Bihler Automatic Machine M35 – Year of manufacture 1987 – 7 t press force – ready for operation For sale is a Bihler automatic machine, model M35, year 1987, in very good and well-maintained condition. The machine features a press force of 7 tons, a compressed air connection with 6 bar, and has approximately 70,000 operating hours. Iolhex Tukqoccqkeib The automatic machine is fully functional and immediately ready for use. Bihler machines are renowned for their robust, long-lasting construction and reliability in industrial applications. The M35 is ideally suited for stamping, bending, and forming operations. The machine can be inspected under power in our workshop by prior appointment. Spare parts are still readily available.

Condition: ready for operation (used), Year of construction: 1979, operating hours: 70,000 h, functionality: fully functional, machine/vehicle number: 24104, working range: 250 mm, feed length X-axis: 170 mm, overall weight: 1,600 kg, total height: 1,860 mm, type of input current: three-phase, pressing force: 7 t, total length: 2,000 mm, total width: 2,500 mm, table width: 184 mm, input frequency: 50 Hz, input voltage: 400 V, input current: 8 A, punching force: 7 t, control cabinet width: 410 mm, control cabinet length: 630 mm, control cabinet height: 1,320 mm, compressed air connection: 6 bar, With 70,000 operating hours, it has certainly seen considerable use, but this is not an unusual figure for machines of this type in industrial operation – many remain productive for years with far higher hours if they are properly maintained. Full functionality is assured – the drive has been replaced once. On the positive side, the machine is fully operational, proven in industrial environments, robust, and there are still many spare parts available for older Bihler machines. Iijlhcsx Ttb Uscqkjb

Year of construction: 1984, condition: good (used), Bihler RM 40 (1984) - Multislide punching stamping bending former Machine is shown with 5 slides, however, a 6th one is available. Several pay-offs for strip or for wire are available. Machine with 8-tons press and 5 or 6 slides - hydraulic clamping for wire or strip. One machine if fitted with a additionnal feeding system from the back of the machine, thru the center hole Iiolhceh T Ulyecqkob

Condition: new, functionality: fully functional, Year of construction: 2025, throat depth: 400 mm, warranty duration: 24 months, Model: GB-4016E Bending pressure (KN): 400 Bending length (mm): 1600 Distance between columns (mm): 1320 Maximum opening height (mm): 430 Slider stroke (mm): 180 Throat depth (mm): 400 X-axis stroke (mm): 400 X-axis speed (mm/s): 400 R-axis stroke (mm): 140 R-axis speed (mm/s): 200 Z-axis stroke (mm): 1040 Z-axis speed (mm/s): 400 Machine power (kw): 17.2 Dimensions (mm): 2090*1265*2290 Iielhcjwzqx Hecqkeb Weight (kg): 3500

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, roller diameter: 60 mm, working width: 1,050 mm, sheet thickness (max.): 1 mm, roll metal bending machine Isitan 1050 X 1.2mm Manual 3 roll Bending Machine, excellent condition for sale manufacturer: Isitan 1050X1.2 Iijlhcowk Rlxecqkjb max sheet width: 1050mm max sheet thickness: 1.2 mm Wire grooves at the ends of the rollers Conical bender roller diameter: 60mm Upper roller removable for easy workpiece removal machine dimensions: length: 130cm height: 100cm width: 65cm weight: 240kg

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2011, operating hours: 70,119 h, machine/vehicle number: A0111A0021, controller model: TruControl 1000, laser source model: Festkörperlaser, travel distance X-axis: 2,500 mm, travel distance Y-axis: 1,270 mm, Equipment: CE marking, safety light barrier, TECHNICAL DETAILS Working area: 2,500 x 1,270 mm Parts flap: 300 x 500 mm Clamping claws: 2 units Laser Solid-state laser: TruDisk 3001 LLK outlets: 1 unit Fiber optic cable: 10 m Cutting head Lens focal length: 200 mm MACHINE DETAILS Operating hours Laser on-time: 70,119 h Total operating hours: 73,936 h Control Laser control: TruControl 1000 Screen size: 15" EQUIPMENT Robust, easily accessible C-frame Precision linear guide system for high-accuracy processing Linear magazine including 2 clamping claws Maintenance-free drives Repositioning device with programmable hold-down Brush tables Good parts container Chip bin Enclosed beam guidance via fiber optic cable ContourLine FocusLine NitroLine Chiller unit Ioljy R Uatshccqkjib Diode-pumped excitation for long service life Upgradeable for up to 3 additional LLK outlets Quick-change cutting head system ControlLine Electro-hydraulic punching head Programmable hold-down plate Tool length compensation Punch lubrication spray Slug extraction system Open control based on Bosch PNC-P Control panel with TFT color display Teleservice via Internet Automatic shutdown USB port Network connection CE marking Multi-beam light barriers Laser source safety monitoring system Quick disconnect for hydraulics Scatter radiation protection Additional LLK outlet for operation with Trumpf system MultiTool function MultiBend function Thread forming function Marking / fast embossing function Roller and deburring technology function Softpunch function Adaptive stroke calibration Spray lubrication for die Additional clamping claw Individually opening clamping claws Height-adjustable clamping claws Automatic clamping claw closing Repositioning cylinder with height-adjustable pressure pieces Sensor for parts chute Loading/unloading aid for brush tables Vibration-damped foundation Chip conveyor with tilting bin Liftable brush segment Parts conveyor belt

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2001, operating hours: 13,817 h, controller model: Siemens Sinumerik 840 D, laser power: 3,200 W, punching force: 22 t, travel distance X-axis: 2,585 mm, travel distance Y-axis: 1,280 mm, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Laser power: 3,200 W Laser model: High-frequency excited CO2 laser TLF 3200W Press force: 22 t X-axis travel: 2,585 mm Y-axis travel: 1,280 mm MACHINE DETAILS Control system: Siemens Sinumerik 840 D Laser beam hours: 13,817 h Laser on hours: 71,637 h Operating hours: 80,188 h EQUIPMENT - Sturdy C-frame - Linear guide with integrated magazine Iielhsy Iz H Ioccqkob - Maintenance-free three-phase servo motors - Programmable hold-down for repositioning - Sensor-monitored part chute 500x500 mm for punching and laser station - Ejector cylinder at the laser chute - Programmable cutting gas pressure control - Laser cutting head: 5'' lens, quick-change system, height control - Multi-beam light barriers - Quick shut-off hydraulics - Extraction system - Compact dust extractor - Protective device against stray radiation at the cutting head - Brush table - Sign function / rapid beading - Softpunch - Small parts blow-out device - Repositioning cylinder - Warp detection - Chip conveyor

Condition: good (used), Year of construction: 1988, Press brake, bending machine, swing bending machine, die bending machine -Handover: in its current condition as inspected Iielhccqjv Tpxqjksb -Function: Manual operation (no automatic operation) -Manufacturer: RAFAMET Swivel bending machine type KM-4 -Drive: mechanical -Max. working width: 2020 mm -Max. sheet thickness: 4 mm -Stop depth: 750 mm -Connected power: kW -Dimensions: 3350/1540/H1510 mm -Weight: 3900 kg

Condition: new, Year of construction: 2024, TP turret punch presses With Durma TP series punch presses, you can achieve top quality with precise and fast turret, improved hydraulics and 3 automatic index stations. With movable platen, part unloader, automatic clamps, Cad/Cam software and control unit, Durma turret punch presses are easy to use. With automation systems that increase both work safety and productivity, user safety is also increased while reducing wasted time. Punching force: 30 tons Working area: 3.000+R x 1.500 mm X-axis movement: 3.000+R mm (repositioning) Y-axis movement: 1.500 mm Y-axis speed: 60 m/min X-axis speed: 70 m/min speed combined X+Y: 92 m/min max. stroke rate (in 1 mm steps, 1 mm sheet thickness): 1,100 1/min max. stroke rate (in 25 mm steps, 1 mm sheet thickness): 325 1/min max. marking speed: 1.200 1/min. main cylinder stroke: 40 mm max. punching stroke: 25 mm max. cutting capacity with fixed tool station steel: 6 mm max. cutting capacity with fixed tool station NiRo: 3 mm max. cutting capacity with index station Stah: 3 mm max. cutting capacity with index station NiRo: 1,5 mm Tool changer (27 stations without tool and holder): 11 x A-station fix: 0,8-12,7 mm 11 x B-station fix: 12,8 - 31,7 mm 2 x C-station fixed: 31.8 - 50.8 mm 1 x D station fixed: 50.9 - 88.9 mm 3 x D-station index: 50.9 - 88.9 mm Positioning accuracy: +/- 0.1 mm Repeating accuracy: + Islhccog Admfoqkjib

Condition: used, functionality: fully functional, Hydraulic mandrel tube bending machine Complete bending sets with mandrels and bending shoes: Ø 18, 20, 22, 25, 2 x 30 + 35 mm Additional mandrels without bending shoes: Ø 28, 2 x 38 + 42 mm Siegfried Volz Werkzeugmaschinen Iiolhcewnrt Sjcqksb Rüschebrinkstr. 151-153 D - 44143 Dortmund - Wambel

Condition: used, 12-piece die block for GEWA press brake Bending tool for press brake, lower tool Type: 0255/14 V-block size: 16 mm for 90° V-block angle: 88° Die depth: approx. 8 mm Height: 120 mm Iislowbvmiohccqkjb Max. pressure per meter: 100 t/m Die base width: 60 mm Total length: 4175 mm Segment lengths: 4 x 835 mm, 1 x 400 mm, 1 x 200 mm, 1 x 100 mm, 1 x 50 mm, 1 x 40 mm, 1 x 20 mm, 1 x 15 mm, 1 x 10 mm Weight: 110 kg Very good condition

Condition: used, CNC press brake FASTI type 904-125/30 serial no. 95-904-5775 year of construction 1995 Pressure capacity 125 ton. Working length 3050 mm Stroke approx. 335 mm Stand projection 300 mm Clearance between the side uprights 2550 mm Iielhccehmmfkjqkjb Tool installation height max. 465 mm (opening width between the tool holders) Table width 90 mm (the clamping system is mounted on the table) Table height above floor 875 mm (910 mm with clamping system) Backgauge X-axis 500 mm Backgauge R-axis 115 mm Backgauge Z-axis approx. 1950 mm Lowering speed Y rapid traverse 90 mm/s Lowering speed Y-operation 8.9 mm/s Return stroke speed Y-retraction 75 mm/s Oil filling approx. 160 liters Motor power 18.5 kW Mains connection 400 Volt, 50 Hz, 20 Amp. - 7-axis CNC control DELEM type DA 58 with LCD screen - 1 axis for back gauge - stop depth (X-axis) - 2 axes for back gauge - fence height (finger R1 + finger R2) - 2 axes for back gauge - stop finger, laterally movable (finger Z1 + finger Z2) - 2 axes for press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and 2-hand control panel or 2-hand control panel only - Hydraulic tool clamping for the TRUMPF upper tool system, with 20 mm clamping groove - Hydraulic tool clamping for the lower tool with 13 mm table groove, depth 21 mm (tool pin 13 x 20 mm) - FIESSLER safety light barrier, type AKAS - 2 material support arms at the front, manually movable to the side and height-adjustable - Electrical diagram, hydraulic diagram, user manual for control available - Control cabinet on the machine - without tools Space requirement L x W x H 5000 x 2500 x 3050 mm Transport dimensions L x W x H 5200 x 1900 x 2950 mm Weight 8.5 tons. Good condition