Used Rotary Shear for sale (5,159)

Condition: used, Single-column hydraulic press SCHÖN type FES / C 7 Machine no. No. 4281 Year of construction 1995 Dsdpfjr I E Itsx Abajki Pressure force 7 ton. throat 170 mm Projection round cycle station 60 mm Table size 310 x 200 mm Rotary indexing table Ø 400 mm, with 12 indexing stations Plunger surface approx. Ø 100 mm Plunger plate 315 x 200 x 35 mm Ram stroke 100 mm Installation height rotary table - ram plate max. 130 mm Table height above floor 890 mm Ram speed rapid traverse downwards approx. 300 mm/sec. Ram speed rapid traverse upwards approx. 300 mm/sec. Ram speed Working speed approx. 30 mm/sec. Drive power 1.5 kW Mains connection 380 Volt, 50 Hz Tank capacity approx. 50 liters hydraulic oil - Rotary indexing control via SIEMENS S7- 1200 - GECHTER pneumatic rotary indexing table with 12 indexing stations - Mechanically adjustable fixed stop - Adjustable pressure holding time in the UT - electrical 2- manual operation Space requirement L x W x H 1450 x 850 x 1900 mm weight 700 kg good condition

Condition: used, Univ. swivel-tilt-rotary table Add-on table for Univ. tool milling machine table size 630 x 250 mm Groove width 14 mm Rotatable and tiltable +/- 30 Swiveling +/-45 - 4x T-slot Weight approx. 120 kg Dedpfx Aogp T D Nebajki

Condition: used, Year of construction: 2001, - Year of manufacture: 2001 Dkodpfoxa Aclox Abaei Specifications - Cutting length: 3100 mm - Capacity: 16 mm - Stroke: 170 mm - Strokes per minute: 10 - Oil tank: 410 l - Motor power: 37 kW - Operating voltage: 400 V - Rated current: 72 A - Main fuse rated current: 100 A - Dimensions (W x H x D): 3750 x 2400 x 3425 mm - Weight: 13800 kg

Condition: good (used), Hydraulic tank cap, tank cap -Hydraulic tank cover: from Atlantic ATS 3006 plate shear -Item No.: HMG 400 x 1 H -Dimensions: Ø 440 x 70 mm -Weight 14.5 kg Dedpfxjykz Rkj Abajki

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 49600 € 947.36 € 130 to 600 mm 5 2 50x18 mm 80 mm 600x18 (max. 600x20 mit D mm 120x120x11 (max. 150x150x mm 45/40 mm 130x12 mm 250x12 mm 15 kW hydraulic drive 2 foot pedals for independant working on punching and section station bending unit with 2 dies, V50 and V90 flat steel stationWITH DEVICE FOR REDUCING DEFORMATION angle iron station with round and square bar cutting triangular notching station with table and gauge punching station with table and gauge gauge 1000 mm with contact switch, for angle / flat steel station operating manual in German and Englisch Dkedeynnggjpfx Abaoi

Condition: good (used), Machine vice base plate, clamping plate, vise plate, rotary table -Rotary table: Turntable for vise -T- Round groove: 20 mm, dimensions see photos -Degree display -Dimensions: 350/320/H45 mm -Weight: 20 kg Dksdpfx Asykzhvjbaji

Condition: new, neu ca. 10 Wochen ab Auftrags Spanien 49500 € 945.45 € 60 to 500 mm 5 40x11 mm 32 mm 350x15 mm 120x10 mm 45/40 mm 150x10 mm 5.5 kW 1950 mm 2000 mm 1900 mm 1900 kg with bending station 5 working stations flat steel shear with device to reduce deformation angle iron shear with round- and squarebars opening triangle notcher punching station press brake device for flat steel table at flat steel station table at notching station length stop 1000 mm with contact switch, for angle, flat or bar station hydraulic drive 2 foot release user manual in GERMAN and ENGLISH Semipaxy:Increased repeat accuracy instead of time consuming laying out ·including B&R 15" CNC with touchscreenand integrated keyboard ·automatic positioning in x- and y axis ·manual feed of sheet to the stop Dkedpfx Ajynnb Robaei ·simple grafic programming by touchscreen ·working area 1.000 x 400 mm ·direct importing of DXF files possible

Condition: used, Year of construction: 2004, gebraucht Dodpfx Asynmyrobaeki 2004 9726 prompt, Zwischenverkauf v Türkei 6750 € 1 1350 mm 3 mm 35 1/min 1.5 ° 550 mm 3 kW 2 Stk. 850 mm 400 mm 1700 mm 1350 mm 1200 mm 950 kg manualback gauge automatic sheet hold down hold down with rubber pads moveable foot switch side support arm 2 supporting arms user manual in GERMAN does not complie with the German UVV and Austrian AMVO

Condition: new, neu ca. 10 Wochen ab Auftrags Spanien 24700 € 474.24 € 1000 mm 400 mm 12 m/min 0,2 mm 0,1 mm 300 kg The Semi Paxy table is a positioning unit with CNC control unit which may be factory fitted onto any GEKA punching machine with a 500 mm or larger throat. THE ASSEMBLY CONSISTS OF: Dedpfx Asynmrhebaski * Mounting plate. * Table assembly with “X” and “Y” axis driven by servo motors. * B&R Power Panel 500 PC based 15” touch screen control * Each axis “X” and “Y” has servo motors with built encoder for precise measurement. * Electric cabinet THE WORK PROCESS IS AS FOLLOWS: * The position of the holes to be punched is programmed either in absolute or incremental dimensions. * When the control is started up, the guide stops are positioned for first hole. * The material to be punched is placed against guide stops and the punching pedal is activated, the ram then cycles. * After the punch has returned to the pre-set clearance height, the table guide stops move to the next programmed position. * Repeat this sequence until all holes are punched. B&R PC BASED 15” TOUCH SCREEN CONTROL MAIN FEATURES: * * B&R Power Panel 500 * Integrated keyboard * Windows embedded operating system * 15” colour touch screen WXGA resolution * Compact Flash Memory. * USB front port * Ethernet port * Easy and user friendly interface * Programming is made through Line Pro software developed by Geka * Importing of dxf/dstv files * Network connectivity * Remote assistance via the internet * Run, design, jog, configuration and alarm modes ELECTRIC CABINET * Electric cabinet containing power and control equipment for the axis positioning and control of the machine * Includes Allen-Bradley Guarmaster® safety relays * Electric cabinet is mounted inside Hydracrop’s or Puma’s frame. If machine is retrofitted, the electric cabinet is mounted out of the machine’s frame. * Standard input power is 400 V - 50 Hz - 3 phases. In case different input requirement is needed, let us know LINE PRO MAIN FEATURES: * It is a visual and a very easy to use application with graphic representations. * It shows the operator the image of the piece that is being designed. * All the process of the part (from designing to manufacturing) can be done and controlled directly from the Positioning Control. * Importing of dxf and dstv files available according to designing specifications of the software. * It is easier to make changes on holes that have been already designed and the operator can easily identify any mistake on the part; as he is watching physically on the screen all the steps of the process of manufacturing of the part. * Line Pro can be installed in a PC for later on sending the file via the network or with a USB stick to the machine * Other X- and Y- ranges are also available, please ask for an offer.

Condition: new, neu ca. 10 Wochen ab Auftrags Spanien 35600 € 679.96 € 110 to 610 mm 5 40/20 bzw. 28/28 mm 80 mm 28 1/min 600x15 / 400x20 mm 152x152x13 mm 50 mm 13x52x90 mm 9 kW 2690 mm 1400 mm 2200 mm 3300 kg Dedpfxoynmrbe Abaski 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit punching unit up to diam. 40 mm fast hydraulic, centring device oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH OPTION: Kit € 970,00 length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm

Condition: new, neu ca. 10 Wochen ab Auftrags Spanien 72800 € 1375.92 € 165 to 610 mm 5 40/30 bzw. 34/34 mm 110 mm 31 1/min 750x20 / 400x30 mm 205x205x18 mm 60 mm 16x58x110 mm 15 kW 2950 mm Dkedoynmq Rspfx Abaei 1600 mm 2200 mm 6300 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit punching unit up to diam. 40 mm fast hydraulic, centring device oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH (sample photos) OPTION "KIT" € 970,-- length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm Further available models of HYD 165 series: model S € 55.200,-- as model SD but 510 mm gap weight 5.200 kg (sample photos) WE HAVE MORE THAN 700 REFERENCES!

Condition: good (used), Year of construction: 1981, sheet width - max. 2535 mm plate thickness 4.0 mm ST plate thickness 2.5 mm VA plate thickness 6.0 mm ALU number of strokes - loaded 20 Hub/min cutting angle 1.7 ° work height max. 900 mm Djdpfxsxabvqo Abaski total power requirement 8.5 kW weight of the machine ca. 3400 kg range L-W-H 2916 x 2250 x 1760 mm Machine from training workshop Good/well-maintained condition (!!) Features: - Robust electro-hydraulic guillotine shear “swing cut” - Electric motorized backgauge - Electric cutting length limiter - Electro-hydraulic cutting angle adjustment - Manual cutting gap adjustment - from the front - Front support table incl. recessed handles - 1x stable side stop, with scale and tilt cam - 3x stable front support arms - 1x freely movable foot switch - Front finger guard - EMERGENCY STOP button at the front - Operating instructions * Special accessories included: - Pneumatic sheet metal holding device for thin sheet metal cuts

Condition: new, table diameter 340 mm table load 160 horizontal kg. table load 100 vertikal kg. swivelling range 0 - 90.0 Grad turning speeds 0.6 - 6.0 U/min bore 60.0 mm motor 230 Volt weight of the machine ca. 56.0 kg range L-W-H 385 x 340 x 375 mm Furnishing: - The table can be adjusted at an angle of 0 to 90 degrees tilt and jam - Start / stop via a location-independent foot switch. Dedpfxoxabm Ne Abaeki - Direction of rotation can be selected right / left. - Adjustable rotation time - The turntable has a 60 mm hollow shaft - The turntable has a diameter of 340 mm. The surface is chrome-plated for Protection against welding spatter. - The table speed is adjustable from 0.6 - 6 rpm. - The control of the welding machine via the turntable control is possible. - The ground contact transmits 300 A / 100%. - The turntable and the control are separate. - HF protected. - COM 1800 control with lap welding - Operating instructions in German Functions COM 1800 control: - Right/left rotation - Infinitely variable speed control - Welding torch on/off - Overlap welding adjustable - Controller for rotation time (2-stroke / 4-stroke) - Speed display

Condition: new, table diameter 500 mm table load 300 horizontal kg. table load 150 vertikal kg. Dkjdpfxsxabl Sj Abaji swivelling range 0 - 90.0 Grad turning speeds 0.2 - 2.5 U/min bore 90.0 mm table height ~ 650 mm mm motor 230 Volt weight of the machine ca. 90.0 kg. range L-W-H 385 x 340 x 375 mm Furnishing: - The table can be tilted and clamped at an angle of 0 ° to 90 ° - manual tilting - Start / stop via location-independent foot switch - Direction of rotation can be selected right / left - Adjustable rotation time - The control of the welding machine via control - 350 amp ground connection Scope of delivery: - control (integrated) - foot switch

Condition: new, total power requirement 230 Volt table diameter 300 mm table load 100 Horizontal kg swivelling range 0 - 90.0 Grad turning speeds 0.2 - 2.0 U/min turning speeds 1.2 - 12.0 U/min bore 20.0 mm weight of the machine ca. 50.0 kg dimensions of the machine ca. 480 x 325 x 470 mm Furnishing: - Precise drive unit with face plate, on a stable floor stand. - clockwise / counterclockwise - 2 speed series, stepless - Swivel range from 0 ° - 90 °. Manual tilt - DC gear motor with worm gear, infinitely variable. - diameter of 300 mm. Chrome-plated surface to protect against weld spatter. Dksdpexaatnjfx Abasi - The device's control panel is easy to understand and use. - Start / stop via a location-independent foot switch. - The speed and direction of rotation are set on the machine. - HF protected. Scope of delivery: - control (integrated) - foot switch

Condition: ready for operation (used), Year of construction: 2007, sheet width 3050 mm plate thickness 6.35 mm thickness at "Niro-steel" 4.00 mm 8.00 mm down holder 10 Stück cutting angle 0°40 - 2°20 Grad 3340 mm work height max. 860 mm 575 mm Control GP 37W2 13 - 33 0 max. 315 bar oil volume 100 ltr. total power requirement 6.0 kW weight of the machine ca. 6030 + 1850 kg In good condition (!!) current new price including accessories approx. 110.000 Euro Special price upon request - in checked conditions - machinevideo - ?v=3JUqSaaJkFQ Equipment: - Robust CNC electro-hydraulic guillotine shear - AMADA CNC touch control, front left ("GP 37W2") * Machine control including information display * Main display with 4 control panels * Control/operation of all functions * Max. 50 cutting programs with 15 sequences each - CNC electro-motorized backgauge * Travel speed 100 mm/sec. - CNC electro-hydraulic cutting angle adjustment - CNC electro-hydraulic cutting gap adjustment - Sighting device & cutting line illumination for viewing the scribe line * ??Shear cutting according to the optical scribe line - Manually adjustable table support plates, including ball transfer units * Grip recesses in the front support table - 2x freely movable foot switches - Operating instructions + circuit diagram SPECIAL ACCESSORIES included: - Backgauge system with 3 stations + separate control: * STATION 1 - AMADA conveyor belt with pneumatic sheet support device * STATION 2 - AMADA conveyor belt with pneumatic scrap deflector * STATION 3 - AMADA stacking device with scissor lift table device - Wooden box with spare knives - 1x AMADA extra-long side stop, with support foot * Length approx. 3.000 mm - 2x AMADA extra-long front support arms Dksdpfx Aexaaghebaji

Condition: new, table diameter 340 mm table load 290 horizontal kg table load capacity 190 vertikal kg turning speeds 0.6 - 6.0 U/min spindle bore 60.0 mm swivelling range 0 - 90.0 Grad weight of the machine ca. 62.0 kg dimensions of the machine ca. 380 x 340 x 425 mm Furnishing: - The table can be tilted and clamped at an angle of 0 to 90 - Start / stop via a location-independent foot switch. Dodpfx Absxaafqeaski - Direction of rotation can be selected right / left. - Adjustable rotation time. - The turntable has a 60 mm hollow shaft. - The turntable has a diameter of 340 mm. The surface is chrome-plated for Protection against welding spatter. - The table speed is adjustable from 0.6 - 6 rpm. - The control of the welding machine via the turntable control is possible. - The ground contact transmits 300 A / 100%. - The turntable and the control are separate. - HF protected. - Operating instructions in German Functions of the COM 1000 control: - Right / left rotation - stepless speed control - welding torch on / off - Control for turning time

Condition: excellent (used), functionality: fully functional, Year of construction: 2011, control type: manual, actuation type: mechanical, sheet thickness (max.): 4 mm, back gauge adjustment: motor-driven, back gauge: 775 mm, power: 7.5 kW (10.20 HP), input voltage: 400 V, input current: 16 A, input frequency: 50 Hz, overall weight: 3,000 kg, Equipment: angle stop, finger protection, foot remote control, type plate available, Mechanical guillotine shear in very good condition! Capacity: 2050 x 4 mm. Easy operation. Electromechanical backgauge 6–775 mm. Light curtain behind the machine. The machine was originally delivered to Norway and was therefore electrically converted from 3x230 V / 27 A to 3x400 V / 16 A. Conversion back to 3x230 V is possible. Transport can be arranged. Loading onto a truck is included in the price. Dksdpfx Abjyqpbwjasi

Condition: good (used), Year of construction: 1990, sheet width 1650 mm plate thickness 3 mm Dodpfxeyh Rp Ue Abajki cutting thickness max. 3 mm cutting length 1650 mm voltage 380 V weight of the machine ca. 0,5 t dimensions of the machine ca. LBH 2,6 x 1,6 x 1,3 m Well-maintained pneumatic/mechanical guillotine shear with foot switch

Condition: new, Year of construction: 2025, Available in following capacities: 1100 x 4/1100 x 5/1100 x 6 mm 1370 x 4/1370 x 5/1370 x 6 mm 1600 x 4/1600 x 5/1600 x 6 mm 2100 x 4 2600 x 4 mm 3100 x 4 mm Dkedpegu N E Djfx Abaei Standard features: -NC controlled backgauge 750 mm with recirculating ball spindles -NC controller including cutting counter -Single cut, continuous cut and inching mode changeover -mobile foot switch with EMERGENCY STOP Angle stop on the left side with T-track -Table extension -Roller balls in the table -manual cutting gap adjustment from the front -Cutting line lighting - All-steel knife 2-edged - Sheet metal hold-down device with hard rubber strip to protect polished sheets -Light curtain on the back of the machine instead of a safety grille (CE) -Foldable front security grille (CE) -Optical function display on the front of the machine -CE conformity -2 years full guarantee -3 years on engine and gearbox Optional accessories: -Adjustable angle stop with degree scale and mm graduation -pneumatic sheet metal holder -ELGO 9521 NC controller -Sheet ejection to the front - Sheet ejection to the front including a pneumatic sheet holding system (optional sheet ejection to the front or back over the entire cutting length with NC controller FUJI touchscreen (return to sender) -Table extension with tilt stop and T-slots -Special knife for VA steels -Special color on customer request

Year of construction: 1960, condition: used, R.A.S. rotary mandrel press Type 200-20 machine no. 117/6 stroke 200 mm pressure force 20 t spindle diameter 60 mm Dsdpsic Rn Usfx Abajki

Condition: good (used), Peddinghaus Combined Section Steel Shear Type 210/ 13 Dkjdpjv D Nzyefx Abaji See condition

Condition: good (used), Hydraulic guillotine shear (used) Manufacturer: Fasti Type: TCHE 254 Max. cutting length: 2540 mm Max. sheet thickness (ST 45): 4.0 mm Distance between side frames: 2540 mm Backgauge adjustable: 0 – 1000 mm Hold-downs: 14 units Motor power: 6.5 kW Machine weight: 3400 kg Required floor space: Width 2950 mm, Depth 2700 mm, Height 1900 mm Foot switch Angle gauge Front support arms Motorized backgauge Cutting edge illumination Digital display for backgauge The machine is in very well-maintained condition and ready for immediate use Forklift on site, free loading onto truck Inexpensive shipping possible Machine location: 48477 Hörstel Dksdpfx Aoyrhfwebaei

Condition: excellent (used), functionality: fully functional, working width: 3,070 mm, sheet thickness (max.): 6 mm, Equipment: CE marking, Used EDWARDS PEARSON Model VE – 3000mm x 6mm guillotine for sale Hydraulic Guillotine Shear for sale Type 04 Capacity: 6.5mm x 3070mm Djdpfx Absyna Rqoajki Including Programmable front operated powered back gauge. Front Supports & Squaring Arm. 3metre x 6mm guillotine

Condition: used, functionality: fully functional, Equipment: CE marking, angle stop, centralized greasing system, documentation/manual, emergency stop, finger protection, foot remote control, safety light barrier, type plate available, LVD Shear Type HSL 40/12.7 Capacity 4x12 mm Year 1991 Weight 14,000 kg Dsdpsykk Acsfx Abajki