Used Short Screwdriver for sale (4,174)

Condition: used, Year of construction: 2013, operating hours: 97,817 h, machine/vehicle number: S0631C0211, controller model: Simatic IPC627, laser power: 3,000 W, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 600 mm, Note: The machine indicates an error, which suggests a defect in the beam source. The replacement parts recommended by Trumpf cost approximately €30,000. TECHNICAL DETAILS Working Area Travel range X-axis: 3,000 mm Travel range Y-axis: 1,300 mm Travel range Z-axis: 600 mm Travel range B-axis: ±135° Travel range C-axis: n × 360° Working height: 605 mm Credpfx Acjz Dvfxopsh Laser Model: TruDisk 3001 Laser power: 3,000 W Scanning frequency: 10 Hz–100 kHz Axis Speeds Simultaneous axis speed: max. 173 m/min X-axis: max. 100 m/min Y-axis: max. 100 m/min Z-axis: max. 100 m/min B-axis: max. 90 rpm C-axis: max. 90 rpm Accuracy Smallest programmable path increment: 0.001 mm Positioning deviation, linear axes X/Y/Z: max. 0.03 mm Positioning deviation, rotary axes B/C: max. 0.005° Positioning error, linear axes X/Y/Z: max. 0.08 mm Positioning error, rotary axes B/C: max. 0.015° MACHINE DETAILS Control and Data Processing Control model: Simatic IPC627 Hard disk storage: 60 GB Color monitor: 12" TFT Network speed: 100 Mbit/s Modem: 56 kBaud/s Pneumatics and Cutting Gas Connection pressure: min. 6 bar Connection pressure: max. 14 bar Compressed air consumption, machine: approx. 30 Nm³/h Compressed air consumption, short-term: max. 40 Nm³/h Cutting gas working pressure: max. 20 bar Electrical Connection Base machine: 47.0 kVA Laser unit TruDisk 3001: 19.5 kVA Laser unit TruDisk 4001: 27 kVA Cooling unit TruDisk 3001: 9 kVA Cooling unit TruDisk 4001: 12 kVA Operating hours: 97,817 h EQUIPMENT Hard disk with RAID controller USB interface Ethernet network connection RJ-45 connector Support for ET BEUI, TCP/IP, Novell Server, and NTFS file system Solid-state laser from the TruDisk series Fast rotary changer with tooling and control system Scrap conveyor for continuous removal of cut-outs and scrap grids

Condition: used, Electric dual-screw unit with automatic feed and pneumatic double stroke BÖLLHOFF Type UVS-100-2-R-E The Böllhoff Uniquick Vario UVS-100-2-R-E dual-screw unit has a pneumatic double stroke via Festo valves and cylinders. In addition, various monitoring systems are installed for complete automation. Technical data: Torque of electric screwdriver: 0.6 Nm Torque of gearbox: max. 10 Nm Speed: max. 20,000 rpm Rated voltage: 3~ 0-230 VAC Current consumption: max. 7 A (per screwdriver) Pneumatic long-stroke cylinder: 80 mm Pneumatic short-stroke cylinder: 20 mm Pneumatic total stroke: 100 mm Screwdriver spring stroke: 20 mm Distance between the two screwdriving tools: 73 mm - equipped with a TORX bit T27 or TP27 (presumably for M6 screws) - a Bosch Rexroth LT303 power module is required to operate the screwdriver. (Power module not included) Screwdriver 1 and 2 each consist of the following components: Rexroth Type Servo motor Rexroth Type 0 Planetary gearbox Rexroth Type 0 Encoder Rexroth Type 0 Straight gear Component details: Electric screwdriver unit Rexroth Servo motor Rexroth Type: EC302 SZ3 Material number: 0 Torque: 0.6 Nm Peak torque: 0.7 Nm Speed: max. 20,000 rpm Current consumption: max. 7 A Rated voltage: 3~ 0-230 VAC Crodpehxvu Eefx Acpeh Weight: 0.8 kg Gearbox unit Rexroth Type: 3GE27 SZ3 Material No.: 0 Efficiency: 90% Gear ratio: i=18.9 Torque: max. 10 Nm Weight: 0.4 kg Installation length 65.5 mm Encoder Rexroth Type: 2DMC012 SZ2 Material No.: 0 Rated torque: 12 Nm Gear ratio: 1 Efficiency: 1 Weight: 0.55 kg Installation length: 118.5 mm Straight gear Rexroth Type: 2GA82 SZ2 1/4"SQ Material No.: 0 Spring travel: 20 mm Spring force: 16 - 34 N Tool holder: 1/4" square Maximum torque: 10 Nm Gear ratio: 1 Weight: 0.2 kg Installation length: 90 mm A motor connection cable of 7m is included. Overall dimensions W x H x D: approx. 180 x 920 x 300 mm Total weight: approx. 20 kg good condition

Condition: used, Electric dual-screw unit with automatic feed and pneumatic double stroke, mounted on a handling device, handling system, or manipulator for screwing applications. Screw unit: BÖLLHOFF / BOSCH REXROTH, type UVS-100-2-R-E The Böllhoff Uniquick Vario UVS-100-2-R-E dual-screw unit has a pneumatic double stroke controlled by Festo valves and cylinders. Various monitoring systems are also installed for complete automation. Screwdriver 1 consists of the following components: Rexroth, type: Servomotor Rexroth, type 0: Planetary gearbox Rexroth, type 0: Encoder Rexroth, type 0: Inline gearbox Screwdriver 2 consists of the following components: Rexroth, type: Servomotor Rexroth, type 0: Planetary gearbox Rexroth, type 0: Encoder Rexroth, type 0: Offset gearbox Dimensions (W x H x D): 165 x 1000 x 200 mm Pneumatic long stroke: 30 mm Pneumatic short stroke: 20 mm Screwdriver spring stroke: 20 mm Last used screws: M6 x 15 mm Electric screwdriver unit Rexroth Servomotor Rexroth Type: EC302 SZ3 Material number: 0 Torque: 0.6 Nm/A Peak torque: 0.7 Nm Speed: max. 20,000 rpm Current consumption: max. 7 A Weight: 0.8 kg Gearbox unit Rexroth Type: 3GE27 SZ3 Material No.: 0 Efficiency: 90% Gear ratio: i=18.9 Torque: max. 10 Nm Crodpfxofx Hyfe Acpsh Weight: 0.4 kg Installation length: 65.5 mm Encoder Rexroth Type: 2DMC012 SZ2 Material No.: 0 Nominal torque: 12 Nm Gear ratio: 1 Efficiency: 1 Weight: 0.55 kg Installation length: 118.5 mm Inline gearbox Rexroth Type: 2GA82 SZ2 1/4"SQ Material No.: 0 Spring travel: 20 mm Spring force: 16 - 34 N Tool holder: 1/4" square Maximum torque: 10 Nm Gear ratio: 1 Weight: 0.2 kg Installation length: 90 mm Offset gearbox Rexroth Type: 2VNA82 SZ2 1/4"SQ Material No.: 0 Spring travel: 20 mm Spring force: 16 - 34 N Tool holder: 1/4" square Maximum torque: 10 Nm Gear ratio: 1 Weight: 0.6 kg Installation length: 153 mm Handling system: JÄGER HANDLING Type: Handy-flex 300 Horizontal movement: 400 mm Vertical movement: 450 mm Load capacity: max. 14 kg Handyflex reach: 250 to 650 mm Handyflex reach when pivoted up: max. 860 mm Rotation radius at full reach: max. 360° Vertical guide column: Ø 30 mm Horizontal guide columns: Ø 20 mm - Balancer for vertical movement - Adjustable load capacity - Adjustable stop for radius limitation Dimensions (L x W x H): approx. 1150 x 650 x 1400 mm Total weight: approx. 90 kg Good condition Without the blue steel pallet as a base plate The blue steel base plate is not included in the scope of supply.

Condition: excellent (used), functionality: fully functional, USM POWERSERT impact wrench with automatic screw feeding for fastening hardware General overhaul Codpfx Ajz Iyn Secporh

Condition: used, Year of construction: 2004, functionality: unexamined, machine/vehicle number: 14-250 001, workpiece diameter (max.): 80 mm, Title: Short Bar Loading Magazine FMB SL 80 S – Year of Manufacture 2004 – including accessories & forklift loading Description: Due to a change in our production processes, we are selling our FMB SL 80 S short bar loading magazine. The machine has operated reliably in our production up until now and is no longer needed due to the changeover. •Manufacturer: FMB •Model: SL 80 S •Year of Manufacture: 2004 •Bar Diameter: 10 – 80 mm •Condition: Used Scope of Supply & Accessories: •Connection cable to the lathe (interface) is directly attached to the machine. •4 different sliding bars / feed bars for different material diameters are included. Loading & Logistics: •A forklift is available on site. •We will assist with loading onto your truck or the shipping company’s vehicle free of charge. Csdpfjz Eh Unsx Acperh Terms of Sale: The sale is exclusively to commercial customers (B2B) and is subject to the exclusion of any warranty and liability for defects. A proper invoice with VAT will be issued.

Year of construction: 2003, condition: good (used), Schatz Advanced Assembly System Schatz Assembly System Length: 5450 mm Height: 3000 mm Crodpfx Aoihiiiocpsh Roll-off cradle Length: 5020 mm 2 x Demag cranes 1 x Liftket electric chain hoist 1 x Schatz 907500 System without Advantech TPC-1260 TE touch panel PC More assembly systems in other sizes – new and used – can be found here.

Condition: new, range L-W-H 960 x 460 x 860 mm weight 75 kg 8 St. Tool trolley with 8 drawers, all with tools. - The pull-out drawers are all ball-bearing. - The entire workshop trolley is lockable. - The workshop trolley has 4 stable castors, 2 steerable and lockable. - The tools included are made of chrome vanadium steel. - The workshop trolley has 4 stable castors, 2 steerable, 2 lockable, which ensure very comfortable rolling. On the tool trolley there is a stable worktop made of polypropylene plastic. - The tools included in the workshop trolley are made of chrome vanadium steel and are stored in Styrofoam/foam inserts. + Drawer 1: - 1/4" inch: 13 nuts from 4mm to 14mm, 11 long nuts 4mm – 13mm Ratchet, universal joint, extension. - 3/8" inch: 10 nuts from 10mm to 19mm, 11 long nuts from 6mm to 19mm Ratchet, universal joint, extension. - 1/2" inch: 17 nuts from 8mm to 32mm, 9 long nuts from 10mm to 22mm Ratchet, universal joint, extension. + Drawer 2: - Accessories 1/4" inch ratchet: Torx nuts without hole T8,T9,T10,T15,T20,T25,T27,T30,T40 Torx nuts with hole TT8,TT9,TT10,TT15,TT20,TT25,TT27,TT30,TT40. Allen nuts H3 to H8 Slotted nuts SL4 to SL7 Cross nuts PZ0 to PZ3, PH0 to PH3 Multi-tooth nuts M8, M10, M12 Five-star nuts TS10, TS15, TS20, TS25, TS27, TS30, TS40, TS45, TS50 - Accessories 3/8" inch ratchet: Attachment for bits Torx nuts without hole T40, T45, T50, T55, T60, T70 Torx nuts with hole TT40, TT45, TT50, TT55, TT60, TT70 Allen nuts – H7, ??H8, H10, H12, H14 Slotted nuts SL8, SL10, SL12 Cross nuts PZ3, PZ4, PH4, PH8 - Accessories 1/2" inch ratchet: Allen H14,H17,H19,H22,H24 Allen key H5,H10,H11,H13 Torx T40,T45,T50,T55,T60,T70,T80 Ribe R9, R10, multi-tooth M16 Multi-tooth M9,M10,M12,M14,M16,M18 Short attachment, long attachment, medium attachment, Torx T30,T45,T50, Allen key H7 + Drawer 3: - Open-end ratchet wrench 8-9-10-11-12-13-14-15-16-17-19-22mm; - Double ring spanner set 8-piece 6-7mm, 8-9mm, 10-11mm, 12- 13mm, 14-15mm, 16-17mm, 18-19mm, 20-22mm - Torque wrench + Drawer 4: Cedpfx Aszb Rbtecpjrh - Precision mechanics screwdriver Slotted: SL3.0 x 100mm, Cross: PH0 x 100mm - Screwdriver with soft grip and outside hexagon: Slotted: SL6 x 38mm ; SL5 x 75mm ; SL6 x 100mm ; SL8 x 150mm Cross: PH2 x 38mm ; PH1 x 75mm ; PH2 x 100mm ; PH3 x 150mm - Torx screwdriver: T6 x 80 ; T7 x 80 ; T8 x 80 ; T9 x 80 ; T10 x 80 ; T15 x 100 ; T20 x 100 ; T25 x 100; T27 x 100 T30 x 100 ; T40 x 150. + Drawer 5: - T-handle Allen / hexagon set with ball head: 3 x 115mm ; 4 x 120mm ; 5 x 140mm ; 6 x 160mm ; 7 x 170mm ; 8 x 175mm ; 10 x 200mm. - T-handle TORX T10 – T40 + Drawer 6 - Circlip pliers set inside/outside 4 pcs., 2x curved, 2x straight - Pliers set: combination pliers, side cutters, straight needle-nose pliers, curved needle-nose pliers, pipe wrench. - hammer + Drawer 7 - Socket wrenches 6, 7, 8, 10, 11, 12, 13, 14mm + Drawer 8 - Tools for bodywork processing

Condition: used, Year of construction: 2021, Drilling capacity in St 60 55 mm threading in St 60 M 30 M 36 Short spindle MK 4 spindle stroke 140 mm throat 300 mm column diameter 145 mm Machine table - usable table surface 615x430 mm T-Slots Amount - Width - Distance 2x14x224 mm distance spindle - column min./max. 150/735 mm feed 0,1 + 0,3 mm/U 0 stufenlos Spindle Speed 70-2.400 U/min. engine 3,0 kW machine weight ab. 380 kg Standard equipment: - 7" TFT LCD display with touch function: * Manual input of spindle speed set value * Actual speed display * Integrated drilling depth display with touch zero point transfer Crsdpfx Acoz I Ub Hepjh * Virtual drilling depth scale in the display * Machine status indicators and warnings on the display * Service information * Selectable operating language: DE/EN/FR/ES/IT/NL/RU - Thread cutting device, for thread cutting with stop, max. 6 threads/min (thread cutting capacity depending on spindle speed), thread depth adjustable via depth stop and on the TFT LCD display (4 tools) - Infinitely variable speed adjustment via adjustment lever - Spindle protection with electrical fuse - Three separate buttons for clockwise rotation - anticlockwise rotation - stop - Mushroom pushbutton (latching) for EMERGENCY STOP - Main switch, lockable - Clockwise and counter-clockwise rotation via contactor control - Control voltage 24 V, protection class IP 54 - Paint finish: DD textured paint signal white RAL 9003, PANTONE 4545c, black Item 20.5 Foot switch in addition to the thread cutting device, for switching the direction of spindle rotation in the process. direction of rotation during the process Item 25. Coolant unit B, consisting of: separate container (33 l), pump with motor protection switch, complete armature motor protection switch, complete fitting Item 37.5 Technology calculator in the display The technology calculator guides you through the cutting task Determination of the cutting data using the following parameters: - Manufacturing process - Tool diameter - Cutting speed - Material table - Transfer function of the spindle speed as set value

Year of construction: 2019, condition: excellent (used), functionality: fully functional, machine/vehicle number: 118413, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Technical data see handout. All warranty rights are excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tool equipment, and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Sales only within Europe, incl. Turkey Cjdpfx Asydqk Hocporh Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. No private sales.

Condition: new, range L-W-H 960 x 460 x 860 mm weight 75 kg 7 St. Tool Trolley – 8 Drawers – Partially Equipped (6 Drawers) High-quality workshop trolley with 8 ball-bearing drawers, 6 of which are fully equipped with tools. The trolley is lockable and equipped with 4 sturdy casters (2 swivel, 2 lockable) for comfortable and safe operation. A robust polypropylene worktop completes the set. Features & Quality: – Ball-bearing, extendable drawers – Central locking mechanism / lockable – 4 casters (2 swivel, 2 lockable) – Tools made of chrome vanadium steel – Tools neatly stored in foam inserts Drawer 1 Ratchet and socket sets 1/4", 3/8", and 1/2", including ratchets, universal joints, extensions, and short and long sockets (approx. 4–30 mm). Drawer 2 Extensive ratchet accessories: Torx (with/without bore), Allen, slotted, Phillips (PH/PZ), spline, Ribe, and five-point – for 1/4", 3/8", and 1/2". Drawer 3 Open-end/ratchet wrench set (approx. 8–22 mm), double box-end wrench set, and torque wrench. Drawer 4 Precision, slotted, Phillips, and Torx screwdrivers in various sizes, including soft-grip versions. Cedsu Img Sjpfx Acperh Drawer 5 T-handle hex/Allen key set with ball end and T-handle Torx set (T10–T40). Drawer 6 Pliers and hand tool set: circlip pliers (internal/external), combination and needle-nose pliers, side cutters, pipe wrench, claw hammer, and center punch set.

Condition: new, range L-W-H 960 x 460 x 860 mm weight 75 kg 8 St. Tool trolley with 8 drawers, all with tools. - The pull-out drawers are all ball-bearing. - The entire workshop trolley is lockable. - The workshop trolley has 4 stable castors, 2 steerable and lockable. - The tools included are made of chrome vanadium steel. - The workshop trolley has 4 stable castors, 2 steerable, 2 lockable, which ensure very comfortable rolling. On the tool trolley there is a stable worktop made of polypropylene plastic. - The tools included in the workshop trolley are made of chrome vanadium steel and are stored in Styrofoam/foam inserts. + Drawer 1: - 1/4" inch: 13 nuts from 4mm to 14mm, 11 long nuts 4mm – 13mm Ratchet, universal joint, extension. - 3/8" inch: 10 nuts from 10mm to 19mm, 11 long nuts from 6mm to 19mm Ratchet, universal joint, extension. - 1/2" inch: 17 nuts from 8mm to 32mm, 9 long nuts from 10mm to 22mm Ratchet, universal joint, extension. + Drawer 2: - Accessories 1/4" inch ratchet: Torx nuts without hole T8,T9,T10,T15,T20,T25,T27,T30,T40 Torx nuts with hole TT8,TT9,TT10,TT15,TT20,TT25,TT27,TT30,TT40. Credpfxsu Impyj Acpjh Allen nuts H3 to H8 Slotted nuts SL4 to SL7 Cross nuts PZ0 to PZ3, PH0 to PH3 Multi-tooth nuts M8, M10, M12 Five-star nuts TS10, TS15, TS20, TS25, TS27, TS30, TS40, TS45, TS50 - Accessories 3/8" inch ratchet: Attachment for bits Torx nuts without hole T40, T45, T50, T55, T60, T70 Torx nuts with hole TT40, TT45, TT50, TT55, TT60, TT70 Allen nuts – H7, ??H8, H10, H12, H14 Slotted nuts SL8, SL10, SL12 Cross nuts PZ3, PZ4, PH4, PH8 - Accessories 1/2" inch ratchet: Allen H14,H17,H19,H22,H24 Allen key H5,H10,H11,H13 Torx T40,T45,T50,T55,T60,T70,T80 Ribe R9, R10, multi-tooth M16 Multi-tooth M9,M10,M12,M14,M16,M18 Short attachment, long attachment, medium attachment, Torx T30,T45,T50, Allen key H7 + Drawer 3: - Open-end ratchet wrench 8-9-10-11-12-13-14-15-16-17-19-22mm; - Double ring spanner set 8-piece 6-7mm, 8-9mm, 10-11mm, 12- 13mm, 14-15mm, 16-17mm, 18-19mm, 20-22mm - Torque wrench + Drawer 4: - Precision mechanics screwdriver Slotted: SL3.0 x 100mm, Cross: PH0 x 100mm - Screwdriver with soft grip and outside hexagon: Slotted: SL6 x 38mm ; SL5 x 75mm ; SL6 x 100mm ; SL8 x 150mm Cross: PH2 x 38mm ; PH1 x 75mm ; PH2 x 100mm ; PH3 x 150mm - Torx screwdriver: T6 x 80 ; T7 x 80 ; T8 x 80 ; T9 x 80 ; T10 x 80 ; T15 x 100 ; T20 x 100 ; T25 x 100; T27 x 100 T30 x 100 ; T40 x 150. + Drawer 5: - T-handle Allen / hexagon set with ball head: 3 x 115mm ; 4 x 120mm ; 5 x 140mm ; 6 x 160mm ; 7 x 170mm ; 8 x 175mm ; 10 x 200mm. - T-handle TORX T10 – T40 + Drawer 6 - Circlip pliers set inside/outside 4 pcs., 2x curved, 2x straight - Pliers set: combination pliers, side cutters, straight needle-nose pliers, curved needle-nose pliers, pipe wrench. - Lath hammer + Drawer 7 - Socket wrenches 6, 7, 8, 10, 11, 12, 13, 14mm + Drawer 8 - Tools for bodywork processing

Condition: good (used), Trumpf TruMicro 6 kW Laser Source High-performance disc laser with nanosecond pulses. The high-performance nanosecond lasers of the TruMicro Series 7000 are based on disc laser technology and combine short pulses and high pulse energies, even at high frequencies. This enables you to remove layers and contaminants at maximum speed, reducing your cycle times. Optimize your processes further by varying the repetition rate while maintaining a constant pulse duration. For efficient and economical cleaning of tire molds, the short-pulse lasers of the TruMicro Series 7000 are the ideal tool. Large-area applications with high average power: Removing material, cleaning, tempering: The lasers of the TruMicro Series 7000 demonstrate their full performance in large-area applications. With pulse energies of up to 100 mJ, they achieve enormous material removal rates. A scanner ensures excellent utilization of the power. Flexible laser light cables transport the light where it needs to be, facilitating the integration of the laser. Manufacturer: Trumpf Type: TruMicro 7050 Laser Source Power: 6 kW Cooling: Water System input power: 380–460 VAC, 3 phases Laser power: 750 W Crjdpfx Asxaktlscpjh Wavelength: 1030 nm Pulse energy: 80 mJ Pulse duration: 30 ns Beam quality: 20 mm Repetition rate: 5 to 100 kHz Fiber diameter: 400 µm IP rating: 54 Dimensions (W x H x D): 1460 mm x 1350 mm x 730 mm You can find more new and used items in our shop! International shipping costs available upon request!

Condition: new, maximum load weight: 90,700 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, total width: 2,850 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Crodpfx Acsw Tgp Dspoh Extract from the specifications. Complete equipment list available upon request. Gooseneck: Gooseneck hydraulically liftable/lowerable and detachable. Length approx. 3,650 mm. For tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at the front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * Lowbed ATX-A with telescopic longitudinal beams in low design with fixed hardwood floor approx. 50 mm thick * With drive-over bridging hooks at the front and pin-lug coupling at the rear * Base width: approx. 2,850 mm, Length: approx. 7,150 mm, Beam height: approx. 330 mm, Beam width: approx. 750 mm * Loading height approx. 480 mm with ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical pin-lug coupling for mounting a lowbed at the front, rear end traverse at the back * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendle axle 3-axle front bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Front bogie tires: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Rear bogie tires: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Final coat with 2 layers of 2-component topcoat, single color in RAL 3002 Carmine Red, according to RAL system 841GL Includes accessories: * Steel front bulkhead, approx. 400 mm high * Plug-in ALU side and rear boards on the gooseneck, approx. 400 mm high, anodized finish * 3.5 kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections at the gooseneck * Front bogie with a separate air connection for pneumatic screwdriver * BEKA-MAX central lubrication for a 3-axle bogie * Preparation for mounting of bolt-on container locks for 1 x 20' or 1 x 30' containers on the outer beams * Without container locks * Mounts for foldable extensions outside on the outer beams of the loading area * One 7-pin socket left and right, front and rear on the rear bogie for warning signs * BEKA-MAX central lubrication for a 5-axle bogie * Socket on the rear bogie for the cable remote control of the steering override * Rear bogie with trough * 2 LED reverse lights mounted on the rear panel * European reflector panels (red-yellow) at the rear * One mud flap at the rear * One LED beacon with bracket left and right on the rear traverse * Two INOX toolboxes 855 x 340 x 390 mm on the gooseneck, left and right * 1-cycle

Condition: excellent (used), Desoutter CVI II Controller with Angle Screwdriver Manufacturer: Georges Renault (Desoutter) Controller: CVI II Angle Screwdriver: 01C11200 CVI II Controller From simple start-up processes to complex sequence applications – with up to 20 phases and 250 cycles – for optimal speed, accuracy, and operator comfort in every application. The controller features various interfaces, including an Ethernet port, an RS232 port, and 7 logic inputs as well as 8 logic outputs (24 volts). The CVI II controller can be used to control a handheld electric tool from the ER series or a stationary, built-in screw spindle from the EM series. It is important to note that the CVI II can also be used in combination with a measurement sensor-controlled angle screwdriver, such as the Desoutter ERA40J, which has a torque range of 8 to 40 Nm and a 3/8" drive. Memory Capacity Between 2,500 and 8,500 screw fastening results per station, depending on the number of cycles and the operating mode (asynchronous or synchronous). Tightening Strategies – Torque and angle monitoring – Angle and torque monitoring – Torque and angle monitoring – Torque and angle rate – Predominant torque – Yield point Crsdpswxv Hkefx Acpoh – Stall torque – Torque and angle – Detection of the plastic zone of the joint – Additional torque and angle sensors – Self-tapping – Current monitoring Connectable Tools: Angle screwdriver / Straight screwdriver / Pistol screwdriver / Stationary screw spindles Dimensions (L x W x H): 400 x 400 x 330 mm Weight: 30 kg You can find more new and used items in our shop! International shipping costs available upon request!

Condition: good (used), WSM Stationary Screw Unit, Assembly Station Assembly of components for car radios and navigation systems, as well as testing of these components. The assembly station is surrounded by a protective enclosure. The service doors are equipped with monitoring switches with interlocking (locking). The doors are locked in automatic mode and can only be opened when the automatic mode is stopped or in manual mode after pressing the "Doors" button on the control panel. The automatic mode cannot be started when a door is open. Crsdpfeibichjx Acpeh Functional Sequence The station is loaded with the pre-assembled unit via the conveyor belt. The following describes the work steps of the automatic station with a process flow for a WT (test object). In normal operation, all 3 stations work in parallel. - Positioning the WT with the pre-assembled unit in Station 2.1 - Lowering the carrier with the scanner and vision sensor - Scanning the 3 codes (front panel, front PCB, SD PCB), comparison with the database - Checking the correct locking of the FFC in the connector - Raising the carrier and lowering the WT onto the belt - Positioning the WT with the pre-assembled unit in Station 2.2 - Positioning the screwdriver and screwing in the front PCB - Lowering the WT onto the belt - Positioning the WT with the pre-assembled unit in Station 2.3 - Lowering the light shield and making contact, moving the carrier with the test sensors from below - Type-dependent testing of the lighting of the SD + CD slots and buttons - Functional test of the CD eject button - Lowering the WT onto the belt > continue If errors occur during the test, they are displayed on the display and can be corrected if possible. To do this, switch to manual mode and open the doors. After the repair and starting the automatic mode, the WT is tested again in the station. If no repair is possible (e.g., screwing error), the WT is marked as NIO (Not In Order) in the control system and is no longer processed. Manual NIO marking and removal are also possible. More new and used assembly stations - find them in our shop! International shipping costs on request!

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, For sale: a GEVO SE5-2E/Z machine for window frame manufacturing. The machine was purchased for a specific project that was ultimately not carried out. It was used only a few times, and therefore is in very good working condition. It has been used sporadically since its purchase. Data from the nameplate: Manufacturer: GEVO Type: SE5-2E/Z Serial number: 571 Year of manufacture: 2021 Working pressure: 7 bar Speed: 2500 rpm Country of manufacture: Germany The machine comes from Stolpex – machinery for windows. Selling as used. Condition as shown in the photos. It can be inspected before purchase, by prior arrangement. Codpjy T Eu Hefx Acporh The machine is ideal for a company involved in the production or processing of window frames.

Condition: used, functionality: fully functional, Year of construction: 2020, Manure spreader with short disc harrow, Volmer T Rubber TRG-W8000, year of manufacture 2020, nominal width 7500 mm, 60 toothed discs 510 mm, 2x16 manure distributors Agrar Pro with 50 mm hose diameter, 10 bar pressure hoses, nitrogen bladder for spring mechanism, 3-point linkage, edge disc 430 mm, side plate on the right, pipe roller 550 mm, hydraulically foldable, warning sign with LED lighting, serial number 090804155. Cedpfsz Hwvkox Acporh

Condition: ready for operation (used), Year of construction: 2021, operating hours: 15,000 h, travel distance X-axis: 800 mm, travel distance Y-axis: 800 mm, travel distance Z-axis: 800 mm, controller manufacturer: SIEMENS, controller model: SINUMERIK 840D sl, spindle speed (max.): 12,000 rpm, number of axes: 4, This 4-axis HELLER H5000 horizontal machining centre was manufactured in 2021. It features a working range of 800 mm in all axes and a maximum workpiece diameter of 900 mm. The machine includes a tool taper of HSK-A 100 and a tool magazine capacity of 50 slots. If you are looking to get high-quality machining capabilities, consider the HELLER H5000 machine we have for sale. Contact us for further details. - Machine Count: 2 units- B-Axis (NC Rotary Table) Resolution / Indexing: 360,000 x 0.001 deg- B-Axis (NC Rotary Table) Speed: 25 rpm- B-Axis Indexing Accuracy Tp (VDI/DGQ 3441 / ISO 230 At): 8 arcsec- B-Axis Max. Tangential Moment: 12,000 Nm- B-Axis Max. Tilting Moment: 18,000 Nm- Voltage / Frequency: 3~ 400 V / 50 Hz- Nominal Current: 65 A- Short Circuit Current Rating: 9 kA- Feed Force X- and Y-Axis (ED S3 -40%): 15,000 N- Feed Force Z-Axis (ED S3 -40%): 20,000 N- Rapid Traverse (POWER Package X/Y/Z): 50 m/min- Acceleration (POWER Package X/Y/Z): 5 m/s²- Rapid Traverse (SPEED Package X/Y/Z): 65 / 65 / 72 m/min- Acceleration (SPEED Package X/Y/Z): 7 / 7 / 11 m/s²- Linear Axis Positioning Tolerance (Tp): 0.005 mm- Tool Taper: HSK-A 100 / SK 50- Speed Range: 5 - 8,000 rpm (Power Cutting 100 G / Power Cutting enforced 100 G) / 5 - 6,000 rpm (High Power Cutting 100 G) / 5 - 13,000 rpm (Speed Cutting 100 i) / 5 - 10,000 rpm (Power Cutting 100 i) / 5 - 12,000 rpm (Dynamic Cutting 100 i)- Drive Power (ED S6-40%): 43 kW / 45 kW / 60 kW- Max. Torque (ED S6-40%): 228 Nm / 360 Nm / 400 Nm / 822 Nm / 1,146 Nm / 2,292 Nm- Front Bearing Spindle Diameter: 100 mm / 110 mm- Max. Permissible Tool Mass: 25 kg (8 kg if every location occupied, 35 kg option)- Tool Chain Magazine Slots: 50 / 100 / 150- Tool Rack Magazine Slots: 265 / 425- Max. Tool Length: 600 mm- Max. Tool Diameter: 112 mm (all locations occupied) / 280 mm (with free locations)- Pallet Dimensions: 630 x 630 mm- Max. Workpiece Diameter: 900 mm- Max. Workpiece Height: 1,000 mm- Max. Clamping Mass (Pallet 1): 1,000 kg (single-sided) / 1,400 kg (double-sided)- Pallet Change Time (without hydraulic clamping): 13 s- Pallet Change Time (with hydraulic clamping): 13.5 s- Coolant System Option PBF: Paper band filter Interlit TMF 600, 40 µm nominal fineness, 1,800 L tank capacity, 50 bar / 70 bar high-pressure coolant (IKZ) option- Coolant System Option VRF: Backwash filter KNOLL VRF 250, 40 µm nominal fineness, 1,200 L tank capacity, 50 bar / 70 bar high-pressure coolant (IKZ) option- Machine Floor Footprint (L x W x H with coolant & conveyor): 7.30 x 3.38 x 3.90 m- Total Operating Power (Machine without coolant system): approx. 37 kVA- Compressed Air Supply Pressure: 5 - 6 bar- Permissible Ambient Temperature: 10 - 45 °C- Material Processed: Aluminum (exclusively)- Estimated Operating Hours: approx. 12,000–15,000 hours (pending confirmation)- Operational Status: Currently installed/in place and powered on Technical Specification Taper Size HSK 100 Crjdoz Ixt Hepfx Acpsh

Condition: used, Zucchelli 9 Screwdrivers in stock to fix or use for spare parts. Codpfx Acszz Rn Ejporh

Condition: like new (used), Year of construction: 2020, operating hours: 500 h, functionality: fully functional, machine/vehicle number: M.1501739, Equipment: documentation/manual, type plate available, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Technical data see handout. All warranty rights are excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tool equipment, and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Sales only within Europe, incl. Turkey Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. No private sales. Cjdpfxezcnkbs Acpsrh

Condition: ready for operation (used), Year of construction: 2012, operating hours: 41,280 h, travel distance X-axis: 165 mm, travel distance Z-axis: 700 mm, total height: 2,200 mm, total width: 1,630 mm, overall weight: 9,000 kg, controller manufacturer: FANUC, controller model: Series 31i-MODEL A, product length (max.): 2,800 mm, number of axes: 8, This 8-axis DOOSAN PUMA TT 1800 SY was manufactured in 2012. It features a maximum turning diameter of 230 mm and a maximum workpiece length of 700 mm. The machine is equipped with two spindles and two turrets, providing enhanced machining capabilities. If you are looking to get high-quality turning and milling capabilities, consider the DOOSAN PUMA TT 1800 SY turn-mill centre we have for sale. Contact us for further details. - Operating Hours: 41,280 h (as of Spindle Hours: 24,632 h (as of Total Machined Parts (TEIL GESMT): 14,162 pcs- Number of Spindles: 2 (Main Spindle & Counter/Sub Spindle)- Main Spindle Speed Range: 50 - 5,000 rpm- Counter Spindle Speed Range: 50 - 6,000 rpm- Number of Turrets: 2 (Tool holders)- Powered/Driven Tools: Yes- C-Axes: 2- Y-Axes: 1 (Upper turret)- Max. Turning Diameter: 230 mm- Max. Workpiece Length: 700 mm- Power Supply Voltage: AC 200/220V, 3-Phase (PE, 50/60 Hz) / 400 V, 50 Hz- Rated Power (Nennleistung): 75.21 kVA- Full Load Current (Volllaststrom): 197.37 A- Interrupting Capacity (Unterbrechungsstrom): 13 kA- Short-Circuit Current (Kurzschluss-Strom): 25 kA- Schematic Output (Schaltplan-Ausgabe): PT1H31AA02- Additional Equipment & Accessories: * FMB turbo 8-80/3200 bar feeder * Chip conveyor * Coolant system with belt filter * Internal coolant supply (IKZ) & supply via turret head * Hydraulic power unit * Large selection of tool holders, collet chucks (REGO-FIX / ER), and turning inserts Technical Specification Counter Spindle Yes Cjdoz I Rbvspfx Acpsrh Driven Tools Yes

Condition: used, Year of construction: 2002, Used machine Equipment: - Constant working height due to a motor-driven, height-adjustable upper section - 1st sanding unit with a rubberized and grooved contact roller, contact roller with 180 mm diameter, 75ø shore, contact roller level adjustable in steps - 2nd sanding unit with a height-adjustable air sanding pad - Belt drive motor 15 kW, 380 volts, with soft start for low power consumption during startup - Parallel, spring-mounted, ground infeed pressure roller - Pneumatic belt tensioning with length compensation - Air-controlled sanding belt oscillation - Immediate stop of the sanding belt drive with disc brake in case of belt breakage, belt slippage, or pressure drop - Automatic star-delta contactor - Thickness indicator for workpiece thickness - Workpiece feed 0.75 kW with a fabric-reinforced rubber conveyor belt Crjdpfx Acjz Iupwopeh - Automatic centering of the feed belt - Rubberized belt drive roller - Ammeter for monitoring the chip removal rate - Max. workpiece thickness 160 mm - Sanding belt dimensions 1120 x 2000 mm - CE version/dust-tested - Infeed roller table - Outfeed roller table - Feed speed continuously adjustable from 3-15 m/min via a frequency converter, control from the front at the operator side - Automatic workpiece thickness adjustment across the entire working width, including over-thickness protection - Adjustment or pre-selection of the chip removal rate via a dial gauge - ENORM-matic quick adjustment with feed release - Operating hour counter in the electrical cabinet Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2016, Parts of a screwdriving station. This was only used in test operations. These consisted of two screwdriving units mounted on a robot gripper. The system was used to screw battery components together. Built in 2016, the system was in storage for the past few years and then sold by Audi. The screw used is approximately 72mm long and M6. Credpfxowh Nu Ts Acpeh Rexroth parts (installed twice): 0 608 720 039; i= 6.74; w=85% 0 608 820 113; Type: 3DMC060; 60Nm 0 608 701 017; max. 20,000 rpm; 3~ 0-230V, max. 14A; 0.11Nm/A 0 608 810 021 0608 810 037; Type 3ULG; i=1; efficiency 95% Weber: 1x ZEL 360 conveyor 1x control unit as shown Everything as shown, inspection requested, as it is unclear whether the system is complete.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Function tested; item originates from decommissioning of equipment from an automotive supplier Manufacturer: Cleco / Apex Tool Group Type: TSE 961446PT Voltage: 380 V DC Current: 2–10 A DC Operating temperature: –20 to +70 °C Crjdpfeyq R T Ujx Acpoh Humidity: 0–90 % non-condensing You can also find the corresponding screw controller in our shop!

Condition: used, Year of construction: 2024, functionality: fully functional, This is a cutting machine manufactured by Scharfen, model ES 300, year of manufacture 2024. The machine has been inspected in our in-house workshop and is fully functional. This machine was an incorrect purchase; it turned out that a miter cutting machine was required. Therefore, it was only used for a short period. You will receive an invoice with VAT shown. Credpfoz Ilm Tsx Acpjh The list price of the machine is €4,082 net / €4,857.58 gross. Our offer price is €2,932.77 net / €3,490 gross. Our used equipment service for you: 6 months warranty on electrical parts, limited to the replacement of defective parts, excluding installation and removal costs. High-quality brand-name equipment at fair prices. Professional overhaul / inspection & expert cleaning. Inspected & fully functional - or your money back. Flexible shipping or self-collection options. Competent advice - before and after purchase. Provision of operating instructions, connection diagrams & spare parts. Inspection according to DGUV V3. Technical data: W x D x H: approx. 580 x 635 x 420 mm Blade: 300 mm diameter, hollow ground, hard chrome-plated stainless steel, long cutting life. Cutting thickness setting: 0-25 mm (infinitely adjustable) Cutting length: 250 mm Cutting height: 210 mm Noise level: less than 70 dB (A) Grinding device removable Voltage: 400 V three-phase or 230 V single-phase Power: 0.6 kW Weight: approx. 51 kg Serial number: 2241096 Year of manufacture: 2024 Condition: used, inspected, fully functional Additional information: Large storage area for sheets Quick and easy to clean Extremely robust and low maintenance 100% stainless steel Shipping: Delivery or self-collection by arrangement. Worldwide shipping on request. Shipping to islands or mountain stations only by arrangement. Do you have any questions, would you like advice, or would you like to see something on-site? You can reach us by phone during our opening hours: Monday to Friday, 9:00 a.m. to 1:00 p.m. and 2:00 p.m. to 5:00 p.m. The sale is exclusively subject to our general terms and conditions (GTC).