Used Stunning Tongs for sale (123)

Condition: good (used), Koma Pigs stunning device This device is suitable for the electrical stunning of animals. From 2019, Regulation (EC) No 1099/2009 of 24 September 2009 concerning the protection of animals at the time of killing applies. According to the new regulations, every animal slaughtering plant should record the stunting parameters. This device has a factory-installed recorder of the deafening parameters, which measures the deafening parameters during slaughter and records them on an SDHC memory card placed in the recorder's socket. The device with the recorder gives the possibility of remote assistance when setting the de-stunting parameters. The operation  is based on the principle of automatic measurement of the body resistance of the deafened piece. In the ready-to-run state, there is only a low safe measuring voltage of approx. 15 V at the open electrodes of the forceps. When the electrodes are pressed against the animal's body, the resistance is measured and a deafening voltage of < 400 V is automatically applied, which is automatically switched off when the deafening process is completed (i.e. the electrodes are opened). Two electrodes are applied to the animal's head, while the third electrode, using a pneumatic actuator, is applied to the area of the heart, causing it to stop temporarily, as a result of which the blood stops flowing and the number of congested muscles decreases. By stopping the heart with the third electrode, it is possible to significantly reduce the incidence of adverse factors affecting the quality of the meat. Pgjdpfjy Edvtex Abzon

Condition: used, axle configuration: 2 axles, loading space length: 110,500 mm, loading space width: 25,100 mm, loading space height: 10,000 mm, Year of construction: 2009, Equipment: ABS, = Additional Options and Equipment = - EBS - Electronic Braking System - Rear air suspension - Front air suspension Pgodoyfp H Nopfx Abzsn = Notes = For vehicle inquiries, please contact Mr. Seidel (by phone at CY NV 1214/20T/37). Crane: Palfinger 44002, radio remote control, support legs middle and rear, pallet tongs, additional spotlights: vehicle rear, crane, air suspension, BPW axles, drum brakes, Tridec steering, both axles steered, central lubrication system, handbrake crank, cargo space dimensions: length 11,005 mm, width 2,510 mm, height 1,000 mm, tire tread depth: 1st axle: 10–12 mm, 2nd axle: 11 mm. If desired, we can provide you with a leasing or financing offer. Mr. Seidel (phone) will be pleased to assist you. For further information, please visit our homepage. ... Subject to errors, changes, and prior sale !!! Steering axle = Further Information = Unladen weight: 16,320 kg Payload: 20,680 kg gross vehicle weight (GVW): 37,000 kg Please contact Tobias Ebert for more information.

Condition: good (used), Pipe grabs, round grabs, laying tongs, round material grabs, scissor grabs -Pipe grab: unfortunately without type designation Podpfx Abelyvdyezegn -Pipe diameter: approx. 400 to 750 mm, see photos -Dimension: 930/470/H1140 mm -Own weight: 124 kg

Condition: used, Westtech Woodcracker W600 W820 W1000 W1350 W1800 Log Splitter Tongs Available immediately Westtech Woodcracker W600 - Jaw opening: 620 mm - Splitting force at 240 bar: 26 t - Dead weight (basic version): 295 kg - Recommended oil flow rate: 25–60 l/min - Recommended operating pressure: 190–250 bar - Carrier vehicle operating weight: 6 t - Optional: Autospeed valve - Optional: Rotator Westtech Woodcracker W820 - Jaw opening: 820 mm - Splitting force at 240 bar: 26 t - Dead weight (basic version): 360 kg - Recommended oil flow rate: 25–60 l/min - Recommended operating pressure: 190–250 bar - Carrier vehicle operating weight: 10 t - Optional: Autospeed valve - Optional: Rotator Westtech Woodcracker W1000 - Jaw opening: 1040 mm - Splitting force at 240 bar: 26 t - Dead weight (basic version): 580 kg - Recommended oil flow rate: 40–80 l/min - Recommended operating pressure: 190–250 bar - Carrier vehicle operating weight: 14 t - Optional: Autospeed valve - Optional: Rotator Pedpfjyfqc Sox Abzogn Westtech Woodcracker W1350 - Jaw opening: 1370 mm - Splitting force at 240 bar: 34 t - Dead weight (basic version): 950 kg - Recommended oil flow rate: 80–150 l/min - Recommended operating pressure: 220–270 bar - Carrier vehicle operating weight: 20 t - Optional: Rotator Westtech Woodcracker W1800 - Jaw opening: 1830 mm - Splitting force at 240 bar: 50 t - Dead weight (basic version): 1990 kg - Recommended oil flow rate: 100–190 l/min - Recommended operating pressure: 240–300 bar - Carrier vehicle operating weight: 20 t - Optional: Rotator Various versions and adapter plates available Price on request. We are an official Westtech Woodcracker sales and service partner, Magni telehandler sales and service partner, JCB construction equipment sales and service partner, Mercedes-Benz service partner, Iveco service partner, and with 800 used vehicles, one of the largest commercial vehicle dealers in Germany. We can supply the complete range of Westtech Woodcracker products for you! Rental available = More information = New: Yes Please contact Tobias Ebert for further information.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm Pjdpfjfgyifex Abzogn 820x610 saw band length 5850 x 41 x 1,3 mm band speed 15 - 100 m/min table height 800 mm total power requirement 5,5 kW weight of the machine ca. 4,45 t dimensions of the machine ca. 5,85 x 3,6 x 2,7 m 2-column band saw for quick cutting, K-tech 800H with pusher system P 15. P 30 (option), Fast, quiet and ergonomic cutting Special development for cutting profiles and beams as well as solid material. The material is fixed vertically on and section sides. The machine is from K-tech 800 H standard with an additional horizontal vice equipped. The interaction of the hydraulic Saw frame lowering, material positioning and the Pusher system is CNC controlled. The machines come standard with the environmentally friendly “B&S-Clean Cut cutting system” with minimal quantity lubrication equipped. This saves cleaning effort and is gentle Resources. CNC Control A CNC control allows programming of up to up to 90 cutting programs with different cut lengths, Quantities and mitres. The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 1250x600 saw band length 8140x54x1,6 mm band speed 15 - 90 m/min table height 855 mm total power requirement 7,5 kW weight of the machine ca. 4,96 t dimensions of the machine ca. 5,7 x 4,0 x 2,75 m 2-column band saw for quick cutting, K-tech 1200H with pusher system P 30. P 60 (option), Fast, quiet and ergonomic cutting Special development for cutting profiles and beams as well as solid material. The material is fixed vertically on and section sides. The machine is from K-tech 800 H standard with an additional horizontal vice equipped. The interaction of the hydraulic Saw frame lowering, material positioning and the Pusher system is CNC controlled. The machines come standard with the environmentally friendly “B&S-Clean Cut cutting system” with minimal quantity lubrication equipped. This saves cleaning effort and is gentle Resources. Pedpfxofgyige Abzsgn CNC Control A CNC control allows programming of up to up to 90 cutting programs with different cut lengths, Quantities and mitres. The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 820x610 capacity 45 degrees: round 550 mm capacity 45 degrees: square 550 mm capacity 45 degrees: flat 550x600 mm capacity 60 degrees: round 370 mm capacity 60 degrees: square 370 mm capacity 60 degrees: flat 370x600/450 mm Pjdpofg E Hmefx Abzjgn saw band length 7260 x 41 x 1,3 mm band speed 15 - 100 m/min table height 800 mm total power requirement 5,5 kW weight of the machine ca. 4,8 t dimensions of the machine ca. 5,85 x 3,7 x 2,7 m 2-column double miter band saw for quick cutting with pusher system P15. Option P30 Hydraulic saw frame lowering • NC controlled • Automatic angular positioning from + 60° to – 60° High quality automatic miter adjustment Special development for cutting profiles and beams. The highest positioning accuracy is achieved via the new “B&S positioning system”. reached. An intelligent NC control ensures smooth interaction of linear encoder and self-braking positioning motor in conjunction with a reliable hydraulic brake using large radial center positioning. The work table is supported by high-quality preloaded bearings, which ensure very smooth rotation. CNC Control A CNC control allows the programming of up to 90 cutting programs with different section lengths, quantities and mitres. Positioning system gripping on both sides The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 1250x600 mm capacity 45 degrees: round 680 mm capacity 45 degrees: square 600 mm capacity 45 degrees: flat 870x600 mm capacity 60 degrees: round 580/550 mm capacity 60 degrees: square 530/450 mm capacity 60 degrees: flat 550x450 mm saw band length 8140 x 54 x 1,6 mm band speed 15 - 90 m/min table height 855 mm total power requirement 7,5 kW weight of the machine ca. 5,3 t dimensions of the machine ca. 5,75 x 4,2 x 2,75 m 2-column double miter band saw for quick cutting with pusher system P15. Option P30 Hydraulic saw frame lowering • NC controlled • Automatic angular positioning from + 60° to – 60° High quality automatic miter adjustment Special development for cutting profiles and beams. The highest positioning accuracy is achieved via the new “B&S positioning system”. reached. An intelligent NC control ensures smooth interaction of linear encoder and self-braking positioning motor in conjunction with a reliable hydraulic brake using large radial center positioning. The work table is supported by high-quality preloaded bearings, which ensure very smooth rotation. CNC Control A CNC control allows the programming of up to 90 cutting programs with different section lengths, quantities and mitres. Pgedpfx Asfg E Hnebzen Positioning system gripping on both sides The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: used, Inverter welding machine for manual electric welding IMS - GYS type PROGYS FLEX 280A CEL MMA welding machine, inverter welding machine, manual electric welding inverter Serial no. IEC 60974 Year of manufacture 2020 Power with mains operation 400 Volt (40% ED) 280 Amp. Power with mains operation 400 Volt (60% ED) 200 Amp. Power for mains operation 400 Volt (100% ED) 170 Amp. Power for mains operation 230 Volt (40% ED) 200 Amp. Power for mains operation 230 Volt (60% ED) 180 Amp. Power for mains operation 230 Volt (100% ED) 150 Amp. Pgodevg Rh Tjpfx Abzsn Adjustment range 5-280 Amp. stepless Mains connection 230 / 400 Volt, 50 Hz. - Operating voltage from 110 to 480 volts alternating current - Adapts fully automatically to the existing mains supply - equipped with 16 Amp. CEE plug for 400 Volt mains voltage - Hot-start function (optimizes the ignition behaviour, simplifies the welding start of electrodes that are difficult to ignite) - Anti-stick function (optimizes electrode guidance and prevents the electrode from sticking) - Arc-Force function (optimizes arc stability and improves penetration) - Digital display - Plug socket for remote control connection - Earth cable with plug connection - Electrode tongs with 3 meter cable and plug connection - Stick electrode welding, can be used for all electrode types up to Ø 5 mm - TIG-DC welding (without TIG hosepack) - The device may be connected to a flexible three-phase power supply between 110 V and 480 V or to a fixed three-phase 400 V power supply (50 - 60 Hz) plus ground wire. This appliance may only be connected to a 3-phase power supply system with 4 conductors, where the neutral conductor is earthed. Dimensions (appliance without cable) L x W x H 470 x 270 x 430 mm Weight (without cable) 23 kg New, unused

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, Water-cooled, pneumatic spot welding tong Nimak L193 TB. Very good used condition, fully functional. Item located in 75053 Gondelsheim. See photos. Shipping by forwarding agent or collection. Pjdpfexmuypox Abzogn

Year of construction: 2025, operating hours: 15 h, condition: like new (used), functionality: fully functional, input current: 230 A, machine/vehicle number: 202505, Absolutely like new! Demo unit (price incl. 19% VAT) - Speed oven with non-stick cooking chamber - Suitable for cooking and heating food - TRIAC circuit for precise power control - Integrated exhaust air management from the cooking chamber Scope of delivery - Starter accessory set consisting of: - 1 × rectangular pan, smooth, 260 × 260 mm - 1 × round snack pan, Ø 190 mm - 1 × round snack pan, Ø 250 mm - 1 × tong for 50 bowls - 1 × turner, 360 mm - 1 × silicone tong, 260 mm - Power cable Housing & design - Color: Red / Stainless steel Technical data - Dimensions (H × W × D): 420 × 540 × 500 mm - Power: 3,000 W Pgedpfx Abjyxy R Tjzjn - Weight: 29.5 kg - Connection: 230 V / 50 Hz / 16 A The speed oven is a compact high-performance unit for professional use in the catering industry. It is suitable for rapid cooking, baking, and heating of various dishes, designed for efficient workflows with high output. The speed oven features a non-stick coated cooking chamber and integrated exhaust air management. Thanks to TRIAC circuitry, the device allows for precise operation and consistent power regulation. Low odor, enables roasting characteristics without fat or oils ... Functionality - Speed oven with non-stick cooking chamber - Suitable for cooking and heating food - TRIAC circuit for precise power control - Integrated exhaust air management from the cooking chamber Extensive accessories available, such as steak contact plates... (Source: Website Reamotion Delmenhorst)

Condition: excellent (used), Butt welding point for one-sided accessible welding points with counter pole and welding cable 1600 mm long with change-over switch for operating mode "STOSSPUNKTEN" o r CONNECTION FOR DALEX POINT WELDING TONGS, Series 31 Pgjdpfx Abopudqmozon with connection cable, main switch 16 A CEE connecting plug

Condition: new, cutting diameter 410 mm saw band length 5800 x 41 x 1,3 mm table height 750 mm capacity 90 degrees: flat 700 x 410 mm capacity 45 degrees: round 410 mm capacity 45 degrees: flat 500 x 410 mm capacity 45 degrees: round links 410 mm capacity 45 degrees: flat links 430 x 410 mm capacity 30 degrees: round 320 capacity 30 degrees: flat 320 x 410 15 - 150 m/min workpiece weight max. 250 kg/m kg 5,5 kW 3200 kg 4500 x 2800 x 2000 mm - The ergonomic panel control can be networked and offers various options Option packages * Teleservice for remote maintenance * Setting sawing programs in the AV * Import of sawing programs from CAD with DSTV interface and data export - Automatic material feed: - In a compact design for shorter sections or with flexible insertion tongs Available in almost all lengths - Exact positioning of the material using servo positioning technology - Pioneering electric saw feed with ball screw: - highest cutting performance and quality, while being gentle on the saw band - Consistent use of the most modern recirculating ball bearing systems: - smooth-running, highly resilient, low-maintenance and play-free - Unique and patented double miter system: - Material is always clamped at right angles Furnishing: - Automatic cutting pressure and feed monitoring - Frequency-controlled AC drive 15-150 m/min, 5.5 kW - Hydraulic material full stroke clamping - Automatic movement of the vices - Saw frame height adjustment automatically - Minimum speed and saw band monitoring - Electric miter tilting via servo motor - Visualized program input with CNC control - Integrated MEBA pliers insertion system from 5-2300 mm per stroke with integrated roller conveyor *Special equipment: - Laser light for cutting line display/marking saws - Chip brush driven - Micro dosing system - Clamping pressure regulation - Material bundle tension - Job menu - Material database - Zero stop - Scraper belt conveyor for optimal chip disposal, 2000 mm long Pjdpox Sr Drjfx Abzegn - Cutting progress control

Condition: used, Pipe gripper, round gripper, laying tongs, round material gripper, scissor gripper, pipe laying device -Manufacturer: Siegert, round material gripper round pliers type RZ Pgedorkp Nqjpfx Abzon -Gripping range: 50 to 250 mm -Load capacity: 250kg -Dimension: 630/250/H450 mm -Town weight: 11 kg

Condition: used, Spot welder, spot welding machine, spot welding machine, spot welding tongs, spot welding machine, projection welding machine, projection welding machine -Manufacturer: Aro, projection welding machine, spot welding machine, water-cooled, type N601 -Welding power: 65 kVA -Welding control: Aro 25-002-2 -Transport dimensions: 1000/510/H1720 mm -Weight: 538 kg Pgodpfxshx E T Uo Abzon

Condition: good (used), beam claw, sheet metal clamp, sheet metal claw, beam clamp, sheet metal gripper, material gripper, material gripper, profile steel tongs, plate gripper, lifting claw, lifting clamp -Manufacturer: Stahl Süssen, Sheet metal clamp: Lifting clamp type SGK Podpfx Abjvgv Apezegn -Clamping range: 0-20 mm -Load capacity: 1000 kg -Dimensions: 190/75/H285 mm -Weight: 6.9 kg

Condition: used, Beam claw, sheet metal clamp, sheet metal claw, beam clamp, sheet metal gripper, material gripper, material gripper, profile steel tongs, plate gripper, lifting claw, lifting clamp -Manufacturer: ip, safety lifting clamp type IPSUNZ 6t with swiveling support ring -Clamp range: 32-64 mm -Load capacity: 6 t -Number: 4x clamps available -Price per piece -Dimensions: 310/100/H420 mm Pgedpfxokm Rn Ij Abzsn -Weight: 24 kg/pc.

Condition: used, Hydraulic press, oil hydraulic press, pressing machine, pressing tool, pressing pliers Pgedsix Rchjpfx Abzon -Hydraulic press: Hydraulic unit novopress type WK 9483 -Pressure: max. 150 bar / 0.45 l/min -with punch set: 1x Ø 18mm, 2x Ø 14mm, 1x Ø11 mm, 1x Ø 9mm -Operation: foot pedal -Connection hoses: for pressing tongs or similar -Dimensions: 850/550/H1250mm -Weight: 158 kg

Year of construction: 1999, condition: used, Pipe grabs, round grabs, laying tongs, round material grabs, scissor grabs, pipe laying equipment -Manufacturer: Cordes, CORWETT pipe-laying device type ZI standard -Gripping width: up to approx. 950 mm, see photos -Load capacity: kg Pgedjlyvdgopfx Abzon -Dimension: 1320/600/H1300 mm -Own weight: 88 kg

Condition: used, Beam claw, sheet metal clamp, sheet metal claw, beam clamp, sheet metal gripper, material gripper, material gripper, profile steel tongs, plate gripper, lifting claw, lifting clamp -Manufacturer: ip, safety lifting clamp type IPUZ with swiveling support ring -Clamping range: 0 - 25 mm -Load capacity: 3 t -Number: 1x terminals available -Price per piece Pgodskm Rnyspfx Abzen -Dimensions: 230/90/H380 mm -Weight: 16 kg/pc.

Condition: good (used), Cold water set, cooling water circuit, heat exchanger, cooling for spot welding device, spot welding machine, spot welding system, spot welding tongs Pgjdpfxolpi Tqo Abzjn -Chiller: complete refrigeration unit -Compressor: Danfoss type: MTZ22JC4A -Pump: Lowara type CEA70/5 0.55 kW -Total dimensions: 740/710/H930 mm -Weight: 196 kg

Condition: good (used), Pipe grabs, round grabs, laying tongs, round material grabs, scissor grabs, pipe laying equipment -Manufacturer: Dolezych, round material gripper type RZ SCH -Gripping width: 100 to 350 mm -Load capacity: 1000 kg -Dimension: 825/390/H550 mm -Own weight: 36 kg Podpelzmxgofx Abzogn

Year of construction: 2002, condition: good (used), beam claw, sheet metal clamp, sheet metal claw, beam clamp, sheet metal gripper, material gripper, material gripper, profile steel tongs, plate gripper, lifting claw, lifting clamp, support clamp, crane clamp Pgedpfevgu Nbjx Abzon -Manufacturer: Greifzug, Corso beam clamp type LT-3B -Flange width: 80 - 320 mm -Load capacity: 3 t -Dimensions: 380/115/H375 mm -Weight: 11 kg

Year of construction: 2000, condition: good (used), beam claw, sheet metal clamp, sheet metal claw, beam clamp, sheet metal gripper, material gripper, material gripper, profile steel tongs, plate gripper, lifting claw, lifting clamp -Manufacturer: Siegert, Sheet metal clamp: Lifting clamp type SGK -Grip width: 1-75 mm Pedpevxruxefx Abzjgn -Load capacity: 2500 kg -Dimensions: 300/150/H390 mm -Weight: 17 kg

Condition: used, Pipe grabs, round grabs, laying tongs, round material grabs, scissor grabs -Pipe grab: unfortunately without type designation -Pipe diameter: 610 to 900 mm -Dimension: 1320/670/H1700 mm Pgedpfx Asix Ay Tobzen -Own weight: 287 kg