Used Traub Tns 65 for sale (90)

Condition: used, Year of construction: 2001, turning diameter 340 mm turning length 750 mm control SYSTEM TX 8H spindle passage 80 mm swing over plan sled 530 mm greates pass round over bed 665 mm turning speed range - main spindle 3.150 min/-1 drive capacity - main spindle 22 kW number of tool places 12 Pos. In our assessment, the machine is in good used condition and can be inspected under power by appointment. Two machines are available. Price per unit. Machine 1: - Images 1-5 - Operating hours approx. 55,790 h Machine 2: - Images 6-10 - Operating hours approx. 54,347 h Technical Features & Accessories: Njdpoxwdw Eefx Afzskt - Y-axis - Accessory package with rigid and driven tool holders - Chip conveyor Accessories, tools, and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Subject to changes and errors in the technical data and specifications, as well as prior sale!

Condition: like new (used), Year of construction: 2022, operating hours: 13,116 h, Max. bar capacity mm: 20 Max. Z-axis travel (sliding headstock/fixed headstock) mm: 205 / 80 Max. spindle speed rpm: 10,000 Drive power 100%/40% duty cycle kW: 3.0 / 5.5 Torque 100%/40% duty cycle Nm: 5.73 / 10.5 / max. 17.2 C-axis resolution degrees: 0.001 Max. rapid traverse Z m/min: 20 Tool stations: 8 Driven tools: 8 Max. tool speed rpm: 12,000 / 8,000 Tool holder diameter mm: 45 Drive power 100%/40% duty cycle kW: 1.0 / 2.0 Turning tool cross-section mm: 16x16 / 20x20 Slide travel X mm: 120 / 165 Slide travel Y mm: ±25.4 Slide travel Z mm: 254 / 567.5 Rapid traverse X/Y/Z m/min: 20 / 20 / 40 B-axis swivel angle degrees: 105 Lower turret: Tool stations: 8 Driven tools: 8 Max. tool speed rpm: 12,000 Tool holder diameter mm: 45 Drive power 100%/40% duty cycle kW: 1.0 / 2.0 Turning tool cross-section mm: 16x16 / 20x20 Slide travel X mm: 120 Slide travel Y mm: ±25.4 Slide travel Z mm: 155 Rapid traverse X/Y/Z m/min: 20 / 20 / 40 Back working device: Tool stations: 4 Slide travel X/Y/Z mm: 120 / ±25.4 / 155 Tool holder diameter mm: 25 Sub spindle: Max. spindle bore mm: 20 Max. spindle speed rpm: 10,000 Drive power 100%/40% duty cycle kW: 3.0 / 5.5 Torque 100%/40% duty cycle Nm: 5.73 / 10.5 / max. 17.2 Slide travel X mm: 235.5 Slide travel Z mm: 258 C-axis resolution degrees: 0.001 Rapid traverse X/Z m/min: 20 / 40 Coolant system basic unit: Pump pressure bar: 3 / 8 Tank capacity l: 250 Njdpfx Ajwuddvofzskt Flow rate at 3 / 8 bar l/min: 80 / 120 Filtration degree µm: 200 Machine dimensions Length x width x height mm: see installation plan* Weight kg: 5,000* Connected load kW: 40 (47 kVA)

Condition: good (used), Year of construction: 2004, functionality: fully functional, Dear Sir or Madam, We are pleased to offer you a Traub TNL 26 CNC Swiss-type automatic lathe from the year 2004. The machine is in well-maintained, fully functional condition. Important Note: This particular model is equipped with only one turret. The TNL 26 was also manufactured in versions with two turrets – this offer explicitly refers to the version with a single turret. Nksdpsxgg Rmofx Afzst Technical Data (excerpt): Manufacturer: Traub Model: TNL 26 Year of manufacture: 2004 Control: Traub TX8i-S Turret: 1 unit, lower position, 12 tool stations, driven tools (all-head drive) Bar capacity: 26 / 32 mm Max. main spindle speed: up to 8,000 rpm Drive power: approx. 6.7 kW (100% duty cycle) / 10.7 kW (40% duty cycle) Torque: 21 Nm (100% duty cycle) / 32 Nm (40% duty cycle) Axes: X1 / Y1 / Z1, C-axis integrated in main spindle Chip conveyor: hinge belt, discharge height approx. 950 mm Machine weight: approx. 4,000 – 4,200 kg Dimensions (L × W × H): approx. 4.4 × 1.4 × 1.7 m Condition & Application The machine is immediately available and ideally suited for the precise production of small and medium batches in the automotive, medical and precision engineering industries. Price & Terms Price: on request / negotiable Delivery: ex site, ex works Inspection: possible at any time by prior appointment. Should you require further information or wish to arrange an inspection, I am at your disposal at any time. Best regards, Arnd Sauter GmbH Björn Sauter

Condition: not inspected (used), Year of construction: 1989, We are offering the following as part of an insolvency sale: 2 x CNC lathes (1 x with sub-spindle, 1 x with lower turret), used + Bar feeder + Accessories 1. CNC lathe with sub-spindle Make: MIYANO Model: BNC 34-S Year: 1989 Control: Fanuc 0-T - HYDROBAR bar feeder - 2 x collet chucks - 1 x 3-jaw chuck 2. CNC lathe with 2 x turrets Make: MIYANO Model: JNC 45-T Year: 1989 Control: Fanuc 0-T - HYDROBAR bar feeder - 1 x collet chuck - 1 x 3-jaw chuck 3. Accessories - Approx. 65 x collets - Approx. 40 x jaw sets - Various tool holders + tools - Documentation Nkjdpex Ed A Defx Afzjt The machines are untested, but they were in operation until decommissioning. Sale is ex-location; loading can be provided at extra cost.

Condition: good (used), Internal item no.: 25090 Driven tool holder Njdjxu Uz Nopfx Afzskt Index / Traub No.: W 7045003 B Very well-maintained condition! The holder was used on a Traub TNL18.

Condition: good (used), Internal item no.: 25091 Nkjdpfx Asxvaqljfzot Driven tool holder Adjustable angle head Index / Traub No.: W 7045011A Very well-maintained condition! The holder was used on a Traub TNL18.

Condition: good (used), Internal item no.: 25088 Nodpfxoxu Dcvs Afzjkt Tool holder Thread whirling holder incl. cutting inserts Index / Traub No.: 12068219 The tool was used on a Traub TNL18 Very well-maintained condition!

Condition: good (used), Internal item no.: 25093 Driven tool holder Nodpfjxvat Tox Afzjkt Adjustable angle head Index / Traub No.: W 7045011A Very well-maintained condition! The holder was used on a Traub TNL18.

Condition: good (used), Internal item number: 25092 Driven toolholder Nkodpfx Ajxvazksfzet Adjustable angle head Manufacturer: Index / Traub No.: W 7045011A Very well-maintained condition! The holder was used on a Traub TNL18 lathe.

Condition: good (used), Year of construction: 2004, control TRAUB SYSTEM TX8H weight 3500 kg range L-W-H 3960 x 1640 x 1800 mm output 11 kW number of spindle speeds 5600 / 4000 min-1 Torque 200 / 280 Nm The TRAUB turning machine TNA 300 was designed for the following machining of workpieces with a turning length of 450 mm. --> for machining metal and plastics with a defined cutting edge using suitable tools. --> for mounting in jaw chucks of sizes 160 to approx. 250 --> for machining material bars up to a Ø of 42 or 65 mm --> with EHS special version Workpiece removal device --> chip conveyor 800 mm long -> Technical data Working range Spindle diameter: 42 mm --> Spindle head DIN 55026, size: A5 --> Clamping fixture diameter: 160-175 mm / 200-250 mm --> turning diameter max: 275 mm --> Distance over turning centre: 35 mm Njdpfowwl Iujx Afzekt --> max. turning length: 450 mm --> Swing diameter over cross slide: 395 mm --> Swing diameter over bed: 520 mm --> Tool carrier Tool holders for cylindrical shank DIN 60880: 12 pcs. --> Shank diameter: 30 mm --> Chisel cross-section: 20x20 mm --> Switching time 1 station: 0.5 sec. --> Switching time each additional station: 0.15 sec. --> Feed drives X-axis: --> Slide travel: 210 mm --> Feed force: 5000 N --> rapid traverse/path speed: 15 m/min --> Z-axis: --> Slide travel: 450 mm --> Feed force: 6000 N --> rapid traverse/path speed: 18 m/min --> Y-axis: --> slide path: +- 35 mm --> Feed force: 6000 N --> rapid traverse/path speed: 10 m/min --> C-axis: --> Speed: 100 min-1 --> Torque: 140 / 196 Nm --> electrical resolution: 0.001 degree --> tailstock quill diameter: 70 mm --> quill stroke: 60 mm --> Stroke of the quick retraction: 280 mm --> quill setting force at 55 bar: 8600 N --> Mounting according to DIN 228: Mk 4 --> Steady rest Clamping range: 8 - 95 mm --> Workpiece removal device Max. part length: 250 mm --> Max. part weight: 3 kg

Condition: good (used), Year of construction: 1989, 1 x automatic lathe Traub TD 16 year of manufacture: 1989 with hydraulic single-bar feed LNS Hydrobar 3.16 -HS 4.4 Year of construction: 1989 Nodpfxovga A Tj Afzekt Equipment: 6-fold star turret Material quick clamping. Long turning device Central lubrication Vogel Accessories: see photos The machine can be inspected under power.

Condition: excellent (used), Year of construction: 2013, Traub TNL 18-7B CNC Automatic Lathe Base machine: 2441 x 1396 mm Weight: 3800 kg Spindle height above floor: 3800 mm Connected power: 24 kW Main spindle Max. bar capacity: 18 mm Max. speed: 12,000 rpm Cross-cut speed: 5,000 rpm Z stroke: 205 mm Rapid traverse: 40 m/min Z measuring system resolution: 0.001 mm Feed force: 3000 N Spindle head / short taper: Traub short taper mount Max. clamping force: 1400 daN Max. clamping pressure: 40 bar Min. clamping pressure: 7.5 bar Piston area: 40 cm2 Total cylinder travel: 5 mm Clamping tube thread: M25 X 1 Counter spindle Workpiece diameter: 21 mm Workpiece clamping depth: 180 mm Max. speed: 12,000 rpm Strokes: X: 120 mm Y: -20/+40 mm Z: 250 mm Rapid traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Max. clamping pressure: 30 bar Min. clamping pressure: 10 bar Top tool turret with B-axis Number of stations: 8 Shank cross-section, turning tool: 16 x 16 mm Stroke: X: 120 mm Y: -25/+40 mm Z: 250 mm Rapid traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Chip-to-chip time: 0.5 sec Measuring system resolution: X: 0.0005 mm Y: 0.0005 mm Z: 0.001 mm Lower tool turret Number of stations: 7 + counter spindle Shaft cross-section, turning tool: 16 x 16 mm Stroke: X: 120 mm Y: -20/+40 mm Z: 250 mm Rapid traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Chip-to-chip time: 0.5 sec Measuring system resolution: X: 0.0005 mm Y: 0.0005 mm Z: 0.001 mm Tool drive for upper tool turret Number of driven stations: Max. 8 Drive power: 2 kW Max. speed: 12,000 rpm Torque: 3.9 Nm Tool drive for lower tool turret Number of driven stations: 7 + counter spindle Drive power: 3.4 kW Max. speed: 12,000 rpm Torque: 7.3 Nm Tool drive for the rear unit Number of stations: 7 Number of driven stations: max. 3 Pitch spacing: 46 mm Drive power: 2 kW Max. speed: 7,500 rpm Torque: 4.7 Nm Drive power: 2 kW Max. speed: 4,000 rpm Torque: 11.8 SCOPE OF OFFER INCLUDES (list is not exhaustive): Traub CNC lathe Tool holders, driven and non-driven Nkedpfxewg Tako Afzot High-pressure and belt filter system Oil mist separator Fire extinguishing system Chip conveyor Bar loader Operational documentation For the exact scope of offer, see the photo gallery No liability is assumed for the accuracy, completeness, or timeliness of the information provided.

Condition: good (used), Year of construction: 2002, TRAUB TNL 12/7 CNC sliding headstock automatic lathe TECHNICAL DATA Bar capacity: 12 mm Main headstock strokes: 130 / 80 mm Spindle power: 4 kW Speed, main spindle: 12`000 rpm Upper turret: 6 positions Lower turret: 6 positions Number of driven tools, turret: 6 Max diameter, counter spindle: 12 mm Speed, counter spindle: 12`000 rpm Dimensions: 2850 x 1100 x 1480 mm SCOPE OF OFFER U.A: (list not exhaustive): Traub TNL 12/7 CNC lathe Meyrat high-frequency spindles, 2 pieces Tool holders (driven and non-driven) FMB Minimag 3200 C bar loader Nodpfx Afet E Dbyszjkt Hydraulic unit High pressure pump Chip conveyor Exact scope of supply according to photo gallery No responsibility is taken for the correctness, completeness and up-to-dateness of the information.

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, spindle speed (max.): 8,000 rpm, bar passage: 32 mm, controller model: Traub TX8i-S, number of slots in tool magazine: 12, Equipment: chip conveyor, TECHNICAL DETAILS Bar capacity: 26 / 32 mm Max. main spindle speed: 8,000 rpm Axes: X1 / Y1 / Z1, C-axis integrated in the main spindle Turret: 1 Tool stations: 12 Drive power: 6.7 kW (100% duty cycle) / 10.7 kW (40% duty cycle) Torque: 21 Nm (100% duty cycle) / 32 Nm (40% duty cycle) MACHINE DETAILS Power-on time: 116,721 h Operating hours: approx. 48,000 h Control: Traub TX8i-S DIMENSIONS & WEIGHT Dimensions (L × W × H): approx. 4.4 × 1.4 × 1.7 m Machine weight: approx. 4,000 – 4,200 kg EQUIPMENT Nodpfx Afjxlfk Nozokt Chip conveyor: hinged belt, discharge height approx. 950 mm

Year of construction: 1989, condition: ready for operation (used), Spindle bore: 42mm, max. workpiece diameter: 115mm, speed: 3150rpm, power: 9kW, bar length: 5200mm. Machine dimensions X/Y: approx. 2100mm/1000mm, weight: approx. 1500kg. Including bar feeder Stamag D 5000 and various accessories such as collets and feed collets. Documentation available. An on site inspection is possible. Nsdpfsxwn Ihox Afzjkt

Condition: good (used), Year of construction: 2001, TNK 36, year of manufacture 2001 including chip conveyor, Resy filtration system In good condition, operated without loader, not under power Nodpfxsxv Sr Io Afzjkt

Condition: used, Year of construction: 1996, spindle passage 80 mm max. turning diameter 395 mm Max. Turning length 750 mm control System TX 8H Nkedpfoxbtqvjx Afzjt max. Spindle speed 3.150 U/min. CNC lathe | TRAUB - TNA 400 The machine is in a well-maintained condition and can be inspected at any time under power. Technical data of the machine will follow soon. We ask for your understanding ! - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags:TNA400 | TNA-400

Condition: used, Year of construction: 1997, spindle passage 80 mm max. turning diameter 460 mm Max. Turning length 1.000 mm control System TX 8F max. Spindle speed 2.800 U/min. CNC lathe | TRAUB - TNA 500 Nsdpfx Afexbtpxezokt The machine is in a well-maintained condition and can be inspected at any time under power. Technical data of the machine will follow soon. We ask for your understanding ! - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags:TNA500 | TNA-500

Condition: good (used), Machining diameter max: 36 mm Maximum spindle speed: 6300 rpm No. of Spindles: 2 Controller: Traub TX8i Toolchanger 1: No. of tools: 12 positions X-axis travel: 50 mm Z-axis travel: 50 mm Toolchanger fronside: No. of tools: 7 positions Speeds: 150 - 3000 Rpm 300 - 6000 Rpm Max. diameter: 40 mm X-axis travel: 370 mm Z-axis travel: 250 mm Nedetrvzxjpfx Afzekt Toolchanger backside: No. of tools: 5 Speeds: 150 - 3000 Rpm 300 - 6000 Rpm Max. diameter: 40 mm X-axis travel: 73 mm Barfeeder: FMB Turbo 5-42 Barlength: 3200 mm Bardiameter: 5 - 42 mm Country of origin: Germany Machine LxWxH: 3400 x 1300 x 1700 mm Machine weight: 4000 kg

Condition: good (used), Year of construction: 1993, - TRAUB control TX 8F - spindle passage 42 mm - Working spindle speed: 40 - 4.000 1/min - 4 grooving slides: stroke 60 mm Nkodpsldd Iqjfx Afzst - 8-fold turret - high pressure pump 25 bar - backworking (2 spindles) - bar feeder (3 m) - chip conveyor

Condition: ready for operation (used), Year of construction: 1996, operating hours: 15,001 h, functionality: fully functional, machine/vehicle number: 462, controller model: Traub TX8F, number of axes: 7, Equipment: bar feeder, chip conveyor, CNC lathe with 7 axes, bar feeder & additional equipment! TECHNICAL DETAILS Bar length: 3000 mm Number of axes: 7 Control: Traub TX8F MACHINE DETAILS Spindle 1 operating hours: 50,318 h Nksdpfx Aew Uiqyjfzjt Spindle 2 operating hours: 32,922 h EQUIPMENT Main spindle Counter spindle 2 turrets 2x C-axis 1x Y-axis Bar feeder: IEMCA CNC BOSS 542 Enclosure Coolant system Chip conveyor

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, machine/vehicle number: 364, controller model: Traub TX8F, number of axes: 7, Equipment: bar feeder, chip conveyor, CNC lathe with 7 axes, bar feeder & additional equipment! TECHNICAL DETAILS Bar length: 3000 mm Number of axes: 7 Control: Traub TX8F MACHINE DETAILS Spindle 1 operating hours: 50,318 h Spindle 2 operating hours: 32,922 h EQUIPMENT Main spindle Njdpjw Ec Aljfx Afzokt Counter spindle 2 turrets 2x C-axis 1x Y-axis Bar feeder: IEMCA CNC BOSS 542 Enclosure Coolant system Chip conveyor

Condition: ready for operation (used), functionality: fully functional, spindle bore: 42 mm, turning length: 206 mm, TECHNICAL DETAILS Spindle power: 5.5 - 9 kW Max. workpiece length: 206 mm Spindle bore: 42 mm Tool holder: 4 slots Nkedpfjwtq Ufox Afzjt MACHINE DETAILS Length (L - R): 2,500 mm Width (F - B): 900 mm Height: 1,700 mm

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: 25//16455, rotational speed (max.): 2,800 rpm, rotational speed (min.): 1,400 rpm, turning length: 65 mm, TECHNICAL DETAILS Turning length: 65 mm Thread length: 40 mm Max. part length: 65 mm Motor speeds: 1,400-2,800 rpm MACHINE DETAILS Total power requirement: 2.6 kW Machine weight: 0.7 t Required space: 1,200 x 700 x 1,600 mm Nedpfewtq Ulsx Afzekt Main voltage: 415 V

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, machine/vehicle number: 5318, spindle bore: 26 mm, spindle speed (max.): 4,750 rpm, TECHNICAL DETAILS Max round diameter: 26 mm Max square size: 18 mm Max hexagon size: 22 mm Spindle power: 2.2 kW Number of spindles: 4 Spindle bore: 26 mm Speeds: 1,180 – 4,750 rpm Nodpfx Aswtq Urefzskt Tool holder: 6 slots MACHINE DETAILS Length L -- R: 1,800 mm Width F -- B: 1,000 mm Height: 1,400 mm Weight: 800 kg Total power: 3.2 kW Operating voltage: 380 V 50 Hz