Used Traub Tns for sale (106)

Condition: ready for operation (used), Year of construction: 1994, TRAUB TNS 65 D / 5-axis CNC turning-milling center TX8D -TX 8D control system -COMPLETE TECHNICAL DATA – SEE PHOTOS -Year of manufacture: 1994 -Hydrobar tool magazine Fsdszpf I Aepfx Al Uopn -Tailstock -Various powered tool holders -Three-jaw chuck -Tool holder -Complete documentation Errors and omissions excepted.

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, Traub CNC lathe TNS60, TX8D, year of manufacture 1990, serial no. 1403 C-axis, rotary tool drive, 1 turret VDI40, tailstock, chip conveyor, through-hole chuck cylinder, collet chuck 185E, AMK drive. Fpedpfx Aljz Eqmte Usn Very good condition, fully functional. Machine geometry has been checked and corrected/adjusted. The machine was completely overhauled in 2019 and has had few operating hours since then; guide rails, spindle bearing, and ball screws are in top condition. Scrapers and belts have been checked and replaced. The machine can be inspected while powered on.

Condition: used, Year of construction: 1990, turning diameter 250 mm Fpedpot Hwq Dsfx Al Ujn turning length 450 mm control TX8D bore 80 mm spindle speed: 3150 U/min. CNC Lathe with Bar Feed and 3 Turrets Very large spindle bore, with bar loading device Please ask for further details.

Year of construction: 1982, condition: ready for operation (used), General CNC slant bed lathe Traub is available. Tool stations: 12, tool holder: VDI40, turning diameter: 180mm, max. swing diameter: 450mm, max. turning length: 490mm, bar capacity: 60mm, travel X/Z: 160mm/490mm, rapid traverse: 15m/min, feed rate: 10m/min, machine dimensions X/Y/Z: approx. 3100mm/2000mm/1800mm, weight: approx. 4250kg, control: Traub System TX-8. An on-site inspection is possible. Fedey I Adbspfx Al Uopn

Condition: used, Year of construction: 1987, Technical details: Fjdpou Ix N Sofx Al Uopn turning diameter over bed: 180 mm turning length: 490 mm swing diameter: 450 mm cross travel: Z-Weg: 168 mm control: Traub TX8D revolution per minute: 20 - 4000 U/min spindle passage: Ø 60 mm operating hours - idle run: 23.495 h tool turret: 12 tools total power requirement: 38 kW Weight approx.: 4,2 t dimension machine xH: 3,6 x 2,5 x 2,2 m Tool holder straight shank DIN 69880 (VDI 3425) Ø 40x63 Röhm lathe chuck Ø 200mm hydraulic clamping Operation via double foot switch and control panel/operating panel. Coolant device The Traub carries an integrated chip conveyor with an ejection height of 1,100mm (currently without function). Accessories: multiple small parts 8 x machine feet without tailstock i.D. *

Condition: used, Year of construction: 1992, operating hours: 27,221 h, functionality: fully functional, machine/vehicle number: 474, turning diameter over cross slide: 240 mm, turning length: 800 mm, rotational speed (min.): 40 rpm, rotational speed (max.): 4,000 rpm, total height: 2,005 mm, total length: 2,953 mm, total width: 1,990 mm, type of input current: three-phase, overall weight: 4,300 kg, Last maintenance performed by INDEX-Werke GmbH & Co.KG on September 29, 2025. Chuck diameter: 200 mm Main drive: 30 kW Speed range: 40-4000 rpm Spindle bore: 65 mm Fpodez Ng I Aspfx Al Uon Turning diameter over cross slide: 240 mm Turning length: 800 mm Cross slide with turret Tool positions: 12 Slide travel, cross/longitudinal: 220/850 Powered tools: 6 Speed at the drive wheel: 4000 rpm Tailstock Arbor diameter / Arbor travel: 85 / 140 Mount according to DIN 228: MK5 Total power: 52 kW Machine weight: 4300 kg Dimensions (L/W/H): 2953/1990/2005 Technical data subject to change without notice. Errors and prior sale excepted.

Year of construction: 2000, condition: ready for operation (used), functionality: fully functional, controller model: TX8H, swing diameter over cross slide: 445 mm, turning length: 1,000 mm, machine/vehicle number: 321, TECHNICAL DETAILS Spindle head according to DIN 55026: A8 Chuck diameter: 250/315 mm Spindle bore: 80 mm Turning length: 1,000 mm Swinging diameter over cross slide: 680 mm Swinging diameter over compound slide: 445 mm Main drive Motor power with direct drive: 31 kW Speed with direct drive: max. 2,800 min⁻¹ Motor power with 2-stage gearbox: 37 kW Speed with 2-stage gearbox: max. 3,150 rpm Tool holder W1 Number of tools: 12 Cylindrical tool shank according to DIN 69880: 40 × 63 mm Tool holder W2 Number of tools: 12 Cylindrical tool shank according to DIN 69880: 40 × 63 mm Swinging diameter over compound slide: 355 mm Fedpfxsz Im U Ss Al Uspn MACHINE DETAILS Control system: TX8H EQUIPMENT Tool holder W2 as an optional extra.

Condition: ready for operation (used), Year of construction: 2018, spindle speed (max.): 10,000 rpm, bar diameter (max.): 20 mm, number of axes: 9, This 9-axis TRAUB TLN20 was manufactured in 2018. It features a maximum bar diameter of 20 mm and a main spindle speed of 10,000 rpm. The machine includes an upper turret with 8 stations and a lower turret with 8 stations, providing versatile machining capabilities. If you are looking to get high-quality turning capabilities, consider the TRAUB TLN20 swiss type turning machine we have for sale. Contact us for further details. • Counter spindle: Yes (both are motor spindles with internal cooling) • Upper turret: 8 stations • Lower turret: 8 stations • Control: TRAUB TX8i-s V8 Fsdpfx Ajz Iaxdol Uopn • Quantity available: 3 unitsUnit details: • Unit 1: • Operating hours: 32,000 h • Unit 2: • Operating hours: To be confirmed • Unit 3: • Operating hours: 38,000 h Additional equipment • Robot: FANUC LR Mate 200iD (included with each machine; 3 robots total) Technical Specification Counter Spindle Yes Driven Tools No

Condition: used, Year of construction: 1992, operating hours: 64,000 h, functionality: fully functional, turning length: 800 mm, turning diameter: 250 mm, rotational speed (max.): 40,000 rpm, Offered is a CNC lathe / turning machine with the brand Traub model TND 400. The machine is functional and currently still in use. Turning diameter: 250 mm turning length: 800 mm Fpodpowzw Hwsfx Al Uon Spindle clearance: 65 mm Turret: 12 tolls with interface VDI 40 Max. speed: 40,000 1/min Control: TX8F Accessories: - Steady rest - ATC tool measurement - Three-jaw chuck from SMW The PLC was revised in 2020 with new Baumüller / Mitsubishi components. Machine will be sold without any warranty. The buyer is responsible for disassembling, loading, and shipping the machine on their own.

Condition: used, Year of construction: 2011, 5 machines are only sold as a PACKAGE. Includes a large set of tool holders, fixed + driven. 1. CNC turning center, 3 units Manufacturer: Traub Type: TNL 26 Year of manufacture: 2011 / 2008 / 2006 Operating hours: 64,154 / 75,849 / 81,823 Control: Mitsubishi TX 8i Equipment: - Main spindle - Counter spindle - Upper turret - driven + Y-axis - Lower turret - driven + Y-axis - Front tool holder - driven + Y-axis - Rear tool holder - Bar loader 2x FMB / 1x Breuning Includes tools for the TRAUB machines Tools + clamping devices: - 54 x driven tool holders - 181 x fixed tool holders - Collets, etc. See photos The machines come from ongoing production. 2. CNC lathe, 2 units, one defective Manufacturer: EMCO Type: Turn 332 MC Year of manufacture: 2010 / 2008 Operating hours: unknown Control: Siemens Sinumerik 840D Equipment: Fpedpfx Alezxhxve Usn - Main spindle - Counter spindle - Upper turret - Lower turret - Bar loader TOP ETL 8-45 One machine comes from ongoing production, one has already been used as a source of spare parts, several components have been removed. Dismantling and loading can be organized by a specialist company for an additional fee.

Condition: good (used), Year of construction: 2009, functionality: fully functional, CNC Lathe TRAUB TNX 65/42 Year of manufacture: 2009 Control: Traub TX 8i-s TECHNICAL DATA - Number of spindles: 2 Fpjdpfxeyw H Szs Al Uon - Number of axes: 12 - Number of turrets: 2 MAIN SPINDLE - Spindle nose: A2-6 - Spindle drive power: 24 kW - Spindle speed: 5,000 rpm - Max. bar diameter: 65 mm - Max. diameter of main spindle chuck: 175 mm - Minimum C-axis resolution: 0.001 degrees SUB SPINDLE - Spindle nose: A2-5 - Spindle drive power: 28 kW - Spindle speed: 7,000 rpm - Max. bar diameter: 42 mm - Minimum C-axis resolution: 0.001 degrees - Travel: 700 mm LEFT UPPER TURRET - Number of stations: 10 - Number of live stations: 10 - X/Z-axis travel: 175 / 650 mm - Y-axis travel: +/- 40 mm - Tool type: VDI 30 - Driven tools speed: 6,000 rpm - Driven tools power: 5.5 kW RIGHT LOWER TURRET - Number of stations: 10 - Number of live stations: 10 - X/Z-axis travel: 175 / 650 mm - Y-axis travel: +/- 40 mm - Tool type: VDI 30 - Driven tools speed: 6,000 rpm - Driven tools power: 5.5 kW ELECTRICAL SUPPLY - Supply voltage: 400 V - Total power: 95 kW WEIGHT AND DIMENSIONS - Footprint: 5,450 x 2,318 mm - Machine height: 2,258 mm - Machine weight: 10,000 kg New spindle since 04/26 ACCESSORIES - 3-color status signal lamp - Coolant tank: RESY * with high-pressure pump * with paper filter - Chip conveyor - Parts extraction - Parts belt conveyor

Condition: good (used), Internal item no.: 25088 Tool holder Thread whirling holder incl. cutting inserts Index / Traub No.: 12068219 Fodoxu Dcvjpfx Al Ujpn The tool was used on a Traub TNL18 Very well-maintained condition!

Condition: used, Year of construction: 2016, controller manufacturer: Mitsubishi, controller model: TX8i-s, _____ Description: Year of manuf. : 2016 Fpodpfxoz A Nz De Al Uen Control : Mitsubishi TX8i-s Mainspindle: Technology:Motorspindle Speed:5.000 rpm Power (max.):35 kW Torque (max.):120 Nm Barcapacity:65 mm Workpiececlamping:Hainbuch Spanntop Kombi Axfix Gr. 65 Subspindle: Technology:Motor spindle, integrated in tool carrier II Speed:7.000 rpm :Power (max.):12 kW Torque (max.):22,5 Nm Chuck:Hainbuch Spanntop Kombi Axfix Gr. 42 Toolcarrier I (X/Y/Z): Technology:Turret with 10 stations Taper:Traub ø45 mm Tooldrive:12.000 rpm, 10 kW, 8 Nm Movement in X/Y/Z:140/100/300 mm Toolcarrier II (X/Y/Z): Technology:Turret with 9 stations Taper:Traub ø45 mm Tooldrive:12.000 rpm, 10 kW, 8 Nm Movement in X/Y/Z:140/100/300 mm Backworking attachment: Technology:Backworking attachment with 8 stations (2x synchron, 6x asynchron) Driven Tools:5 stations Tooldrive:12.000 U/min, 6,7 kW, 5,3 Nm Equipment/Accessory: Positionsensor:Direct Scales in X (up/down) Chipmanagement:Chip conveyor Coolingmanagement:Internal cooling unit with Paperbaletfilter and High-pressure, 80 bar Coolanttemperaturecontrol:Interface for external chiller prepared, Deltatherm Wasteheatmanagement:Interface for external chiller prepared Rawmaterialfeed:Barloader, FMB SL 80 V Finished part removal:Unloading device (NC-controlled) with coneyor belt Fireextinguishing unit:Kraft + Bauer Oilmistseparation:Electrostatic extraction LTA AC 3001 Further Accessory:Misc. used static and driven Toolholder

Condition: used, Year of construction: 2007, turning diameter 275 mm turning length 900 mm control TRAUB TX8i-s spindle passage 65 mm spindle turning speed - stepless 1 - 5.000 U/min spindle diameter in front bearing 110 mm C-axis 1 - 500 U/min x-axis 175 mm z-axis 650/975 mm y-axis +/- 40 mm rapid traverse X/Y/Z 20 / 40 / 20 m/min feed capacity X/Y/Z 5,5 / 5,5 / 10 kN tool turret - number of stations 10 number of driven tools 10 mm toolpiece turning speed range 1 - 6.000 U/min Fpsdpfxjzwg Nds Al Uen power capacity at 25 % load 5,50 kW max. torque at 25% load 17,50 Nm tool taper DIN 69880 Ø30x55 spindle diameter in front bearing 110 mm total power requirement 95,00 kW weight of the machine ca. 16,00 t dimensions of the machine ca. 10,00 x 3,50 x H3,00 m

Condition: good (used), functionality: fully functional, 1 x multi-spindle automatic lathe Traub TD 26 Fpjdpfxjz Agyae Al Uon with boring unit + tool magazine Iemca AS 325/32 CT Year of manufacture: 1992 + chip conveyor The machine can be inspected while powered on.

Condition: good (used), functionality: fully functional, 1 x Multi-spindle lathe Traub TD 26 with loading magazine Iemca Fpodpfjzz Nf Njx Al Usn Boss 432/32 Year of manufacture: 2002 + Chip conveyor GS Industrietechnik K-I-150 Year of manufacture: 2017 Equipment: Drill chuck pneumatic workpiece clamping (Wachtler)

Condition: used, Year of construction: 1987, operating hours: 80,678 h, functionality: fully functional, Description follows Fpsdpsx A Hl Asfx Al Usn

Year of construction: 2023, condition: ready for operation (used), An unused Traub CNC twin-spindle turning and milling center with peripheral equipment is available. Spindle types 1/2: D76/D76, max. turning length: 900mm, max. workpiece diameter: 76mm, number of tool carriers: 3, control system: Traub TX8i-s V8. Main spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Counter spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Upper tool carrier: axes: X/Y/Z, stations: 12. Lower left tool carrier: axes: X/Y/Z, stations: 12. Lower right tool carrier: axes: X/Y/Z, stations: 12. Including Isi Elbaron RON4DHEC mist extraction and filtration system, custom-built circulation conveyor, Bürener hinged belt chip conveyor, Bürener Eco-Fluid coolant system (600l), cooling unit, coolant chiller, Traub WH workpiece handling system, various grippers and gripper pairs, IoT, and management and monitoring software. This machine was never put into operation and is therefore in as-new condition. Documentation available. An on-site inspection is possible. Fjdpfozkvkqex Al Uopn

Condition: good (used), Year of construction: 1999, operating hours: 110,000 h, functionality: fully functional, spindle bore: 42 mm, Description follows Fpsdex A Ha Hjpfx Al Usn

Year of construction: 2005, condition: good (used), 7-position tool holder for CNC lathes Manufacturer: TRAUB, Model TNA 480, tool holder size VDI 40. Also compatible with SAUTER tool turrets with VDI 40 mounting. 7-position horizontal tool holder, positions no. 3/4/5/6/7/8/9 for drilling and milling, price per piece: 550,- € 2-position horizontal tool holder, positions no. 1 and 2 for tapping, price per piece: 600,- € 1 NC drilling chuck VDI 40, clamping range 1-13 mm, price: 100,- € Fjdpfxehwnfko Al Ujpn 1 NC drilling chuck VDI 40, clamping range 2.5-16 mm, price: 150,- €

Condition: used, Year of construction: 2011, controller manufacturer: Mitsubishi, controller model: TX8i-s, _____ Description: Year of manuf. : 2011 Control : Mitsubishi TX8i-s Mainspindle: Technology:Motorspindle Speed:5.000 rpm Power:22,6 kW Torque:180 Nm Barcapacity:65 mm Workpiececlamping:Collet chuck, Hainbuch Spanntop Kombi Axfix Gr. 65 Subspindle: Technology:Motorspindle Speed:5.000 rpm Power:22,6 kW Torque:180 Nm Workpiececlamping:Collet chuck, Hainbuch Spanntop Kombi Axfix Gr. 65 Ejector:Hydraulic with flush Toolcarrier I (X/Y/Z): Technology:Turret with 10 stations Taper:VDI30 Tooldrive:6.000 rpm, 5,5 kW, 17,5 Nm Movement in X/Y/Z:175/80/650 mm Rapid travers in X/Y/Z:20/20/40 m/min Toolcarrier II (X/Y/Z): Technology:Turret with 10 stations Taper:VDI30 Tooldrive:6.000 rpm, 5,5 kW, 17,5 Nm Movement in X/Y/Z:175/80/650 mm Rapid travers in X/Y/Z:20/20/40 m/min Toolcarrier III (X/Y/Z): Technology:Turret with 10 stations Taper:VDI30 Tooldrive:6.000 rpm, 5,5 kW, 17,5 Nm Movement in X/Y/Z:175/80/650 mm Fpodjzr Dd Uspfx Al Usn Rapid travers in X/Y/Z:20/20/40 m/min Equipment/Accessory: Chipmanagement:Chip conveyor Coolingmanagement:Internal cooling unit with Paperbeltfilter and Highpressure, 80 bar Coolanttemperaturecontrol:Interface for external chiller prepared, Deltatherm Rawmaterialfeed:Barlaoder, FMB SL 80S Finished part removal:Unloading device (NC-controlled) with coneyor belt Oilmistseparation:Electrostatic extraction, LTA AC3001 Further Accessory:Misc. used static Toolholder

Condition: good (used), Year of construction: 2002, functionality: fully functional, 1 x CNC turning center Fsdpjwtlz Tjfx Al Uopn Traub TNA 300 Year of manufacture: 2002 (Spindle hours: 40746) Control: System TX 8 H with bar feeder LNS Hydrobar + chip conveyor Knoll Well-maintained machine with an extensive range of accessories, in excellent optical and technical condition. Accessories 33 x VDI 30 tool holders for turret (11 of which are driven) 1 x additional collet chuck with spindle reduction sleeve 10 x collet 181 E 10 x collet 171 E optional 1 x rotating steady rest in tailstock 1 x ATC optics Complete documentation The machine can be inspected while running.

Condition: good (used), Year of construction: 2008, functionality: fully functional, Traub Stamag DNH42/3000, year of manufacture 2008, DNH42, bar feeder, loading magazine, loader. Fjdpfxozp Ec Ho Al Uepn

Condition: good (used), Year of construction: 2013, TX8i-s / WinFlexIPS Bar diameter up to Ø 32 mm Design allows for conversion between long and short turning Controlled axes: 9 Fpsdpfx Ajzzahzjl Ujn Tool holder WRV on top, X/Y/Z dual drive Counter spindle with WRV on the bottom, separate drive Rear unit with drive Rated voltage 400 V, 3~, N, PE · 50 Hz Connection power 28 kVA, pre-fuse 63 A Recommended supply line: 16 mm² up to 30 m, otherwise 25 mm² Total drive power 46 kW · 73 A Compressed air requirement approx. 300 Nl/min Machine weight 6,850 kg Dimensions L × W × H 3,870 × 1,670 × 2,500 mm Safety standard EN ISO 23125, design type 3 small - Coolant lubrication with cutting oil — internal feed 30 bar, medium pressure 20 bar, high-pressure internal cooling 80–120 bar with its own pump - Coolant treatment system with strip filter (ELBARON) - Mist extraction and fume separator - Fire protection and extinguishing system — prerequisite for unmanned shifts with oil - Workpiece removal with linear unit (part gripper) - Incl. various clamping jaws - Linear measuring system in the X-axes - TRAUB tool monitoring and WinFlexIPS programming - Bar loader FMB turbo 3-36 for bars up to 3,200 mm, with synchronous and displacement device - Chip conveyor, hinged belt - Color: Dust gray RAL 7037 Machine operating time approx. 30,600 hours Machine price without the shown accessories (extensive accessories can be purchased separately) Errors and prior sale excepted. The machine can be inspected under power with short notice.

Year of construction: 1984, condition: used, A CNC lathe is offered. Equipped with three-jaw chuck, tool turret and hydraulic unit. Control: TRAUB SYSTEM TX 8. Inspection possible by prior arrangement. Fpsdpfez Hlxmox Al Usn