Used Welding Converter for sale (7,758)

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Phsdpfxswu Tu Do Agzja Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: used, Year of construction: 2011, Available from October 2025 1st Urban AKS 6405 - Year of construction 2011 - Min. welding dimension: 323 x 382 mm - Max. Sealing dimension: 2300 x 2520 mm - Applied profile systems: Veka Softline 70, Topline 70, Swingline 70, Softline 76, Softline 82, Topline NL, Softline NL, Alphaline 90, Topline Plus - Weld bead limitation 2 mm (no stainless steel blades) - Operating system: Windows XP 2nd Urban SV 530 Phodpfx Asulfxaegzsa - Year of manufacture 2005 - Incl. Urban WT turning station + cooling station - Operating system: DOS (complete PC replaced in 2023) - Various components replaced (DARC V05-10-20 supply module in 2018) - Cutter for 2.5 mm groove (no V-groove)

Condition: good (used), Inert gas welding machine with pulse function, pulse-arc welding system, MIG/MAG pulse welding system -with: 3 hose packages (1x aluminum, 1x stainless steel, 1x steel) -Max. welding power: 330 A Podsd I U Dwspfx Agzsha -Equipment: remote control connection, with removable wire feed, including ground cable, gas fitting -Wire feed: 4-roller drive -Cooling: Water-cooled -Dimensions: 655/900/H1490 mm -Weight: 160 kg

Condition: like new (used), functionality: fully functional, The following item is for sale: - Our offer number: 2/129 - Resistance welding control welding inverter - Manufacturer: Matuschek Pjdpfx Agordyqmezeha - Type: Spatz H 6000 - Type number: H60A012 - Serial number: H60072262 - Power: 33KVA 3-400-500V 50/60 Hz - Dimensions: WxHxD 380x460x220 mm - Weight : 29 Kg - optical condition according to photos - New / as new condition with traces of storage - functional Notes: The goods offered here usually come from company liquidations and bankruptcies. Due to missing type plates, it is not always possible to provide exact item data. The item pictures are original photos that show the actual condition of the item. If several identical items are offered, only one of the items will be photographed. There may be slight variations in the condition of the individual items. If an item is opened or repaired/rebuilt by the buyer, any warranty claim will be void. This also applies if repairs and modifications are carried out by third parties without prior agreement. Jwt9nu Company names and trademarks used are the property of their owners. They serve exclusively to identify and describe the goods available.

Condition: refurbished (used), Year of construction: 2025, working width: 2,450 mm, Refurbished Schlatter MG903 - ZG24 - Longitudinal wire insertion LFE - Longitudinal wire feed LV - MG24.4 mesh welding machine - Cross wire feeder QF8 - Mat extraction MVL4.2 - De-stacker MS12 Control and power cabinet - Siemens S7 TIA machine control Pedpfov Ed Anex Agzoha Mesh size : 2450mm Wire: 2-12mm

Condition: refurbished (used), Year of construction: 2017, EFI Vutek H2000 Pro UV Hybrid Printer Print width flatbed/roll: 205 cm Color: 6C+ White (over and under print) Resolution: 1000 dpi, 7 pl drop size Ultradrop Speed up to 1000 m2/h Roll option Pedpfx Agoxpwx Tezjha Fully refurbished

Condition: used, Stainless steel welding line MOD.70/120, made OLIMPIA 80 with tricathode welder & Seam bead roller & Orbital polishing Specifications: Podevtn H Topfx Agzoha - Diameter : 35 – 120 mm - Thickness : 0.7 – 3.5 mm - Length : 3 – 6 m Tube diameter: 35 – 120 mm Thickness: 0,7 – 3,5 mm Tube length: 3 – 6 m

Condition: ready for operation (used), Siemens / Delta D0012401 / 78-092-0300 Converter E-Stand: 0, REV: 01 SN:026635, used, in like-new condition, 100% fully functional, scope of delivery as per photos Pjdex Eum Aspfx Agzsha

Condition: good (used), Heat exchanger for inert gas welding machine, inert gas device, cooler Phedpfx Aewubqtegzoa -Manufacturer: CLOOS, heat exchanger from inert gas welding machine GLC 353 MC3 -Blower: ebm papst type M4Q0465-DA01-S8 -Dimensions: 330/160/H330 mm -Weight: 4.2 kg

Condition: refurbished (used), Year of construction: 2007, functionality: fully functional, warranty duration: 3 months, type of cooling: water, welding current (min.): 30 A, welding current (max.): 400 A, For sale: OTC DP400 30-400 AMP 50% ED 400A 60% ED 365A 100% ED 283A 400 Volt Water-cooled Pulse Synergic 2/4 Step 4 Roller drive Pre gas Post gas Start current End current Spot welding Fixed programs Program memory Steel – Stainless Steel – Aluminum weldable Refurbished, serviced, & tested Production date: 2007 Including PRO5000 Welding torch, earth work lead with clamp, gas cable, and 3 months warranty. Visits by appointment only. Test welding is possible. A video of the machine in welding condition is possible. We also deliver to countries like Spain, Germany, Austria, Lithuania, Greece and all other countries inside and outside Europe with Euro pallets per freight. All our machines have been serviced and are 100% ready to use unless otherwise indicated. The pictures above show the real machine. We can also offer you other types of machines such as: Used, New, Mig, Mag, Co2, Tig, Pulse, AC/DC, Plasma, Water-cooled, Electrode, Brands we offer: OTC, Migatronic, Lincoln, Miller, Fronius, Kemppi, Parweld, Tico, Lorch, Rehm, Selco, Carl Cloos, Cebora, Esab, Saf, EWM, Ess, Kemper. Phsdpfsx Ea I Aox Agzja You always do business with Cjays Lastechniek itself and never with third parties.

Year of construction: 2002, condition: used, plant 2 x ultra-sonic welding machine KLN GCO, Generator MCA, Control device PXO, 30 kHz, 1.000 Watt, control System in cabinet SIEMENS, year: 2002, Price: 15.900 €, contact: Mr. Rainer Eckerle Phjdpfx Aecmum Djgzja

Condition: like new (used), Year of construction: 2013, Technical Data / technical details: The FLW is a flexible and highly productive laser welding cell with extensive equipment. The focused laser beam is used as an energy source to melt and join materials together. The laser welding cell consists of a fiber laser and a 6-axis industrial robot, which moves along a travel rail. The parts to be welded are clamped onto a rotary-tilting table. The safety enclosure is equipped with a sliding door to ensure safe operation. Robot: Type: M-710iC/50 (FANUC) Robot controller: SYSTEM R-30iA (FANUC) CNC control: AMNC Number of controlled axes: 6 Reach: 2,050 mm Welding head: AMADA Repeatability: 0.07 mm Safety enclosure: Full enclosure Robot track: Length: 1,500 mm Travel speed: 60 m/min Repeatability: ± 0.1 mm Positioning table: Working height: 700 mm Pjdpfx Agexndynozeha Max. load capacity: 500 kg Rotary axis: ± 720° Tilting axis: ± 90° Laser source: Type: YLS4000-S2T Wavelength: 1,070 – 1,080 μm Laser power: 4 kW Control: Type: Amada Display: 15” LCD colour touchscreen Controlled axes: Robot and linear axis Coordination between robot and laser source Memory: 3 MB SRAM I/O interface: LAN, USB Welding Head: Amada Focus position adjustment: -10 mm to 50 mm CCD camera for TAS system included as standard Optical weaving included as standard Cross jet nozzle included as standard Coaxial nozzle included as standard Welding wire feed: 0.8 to 1.6 mm Weaving System: The integrated rotary optics allow the laser beam to move in a circular pattern. The patented system by AMADA enables welding of larger gaps with or without filler material and even allows welding of aluminum. NC Focus System: The NC Focus System automatically sets the optimal focus position for the specific welding condition. It supports welding simple butt joints as well as hard-to-reach corners. Filler wire and intelligent gas supply: Up to 20 kg of filler wire can be used. When using the TAS (Teach Assistant System), the gas nozzle retracts automatically. TAS (Teach Assistant System): The TAS system eliminates time-consuming manual teaching operations. Deviation between the programmed and actual weld path is detected using a CCD camera. Condition: Very good condition Machine has been used very little: approx. 16,500 operating hours. The seller is not liable for typographical or data transmission errors. The machine’s appearance, technology, and wear are commensurate with its age; used machines are sold without any warranty.

Condition: refurbished (used), Year of construction: 2025, JAGER welded mesh line U-Gsa-st Full revamped "as new" Technical data 24 pay off for longitudinal wire spools, longitudinal wire straightening equipment Line wire pull off system Longitudinal wire loop Longitudinal wire straightening equipment Cross wire magazine Number of installer line wires : 24 up to 10 mm Diameter of lines wires : 4 to 10mm Diameter of cross wires : 4 to 10mm Phjdewu Dcxopfx Agzoa Separation between line wires : 100, 150, 200, and 300 mm Separation between cross wires : min 30 mm , steplessly programmable Max. length of cross wire (mesh width) 2500 mm , max welding width : 2400 mm Mesh length : min 3000 mm and max . 6000 mm Trafos : 8 x 160 Kva Number of installer line wires: Number of installer line wires : 24 up to 10 mm Diameter of lines wires: 4 to 10mm Diameter of cross wires: 4 to 10mm Separation between line wires: 100, 150, 200, and 300 mm Separation between cross wires: min 30 mm , steplessly programmable Max. length of cross wire (mesh width): 2500 mm Max welding width: 2400 mm Mesh length: 3000 - 6000 mm Trafos: 8 x 160 Kva

Condition: good (used), load capacity: 3,000 kg, Hywema 3-ton double-column rotating lifting device with 3rd axis multifunction including 2 universal joints There are 4 variants: - Mono single-column rotating lifting device - Duo double-column rotating lifting device with universal joint - Duo double-column rotating lifting device with crossbeam approx. 5m length for bolting (additional screw-adjustable height) - Duo double-column rotating lifting device with crossbeam for bolting and additional 3rd rotational axis with 3-ton load capacity Travel distance min. 700 mm (+/- 150 mm) Travel distance max. 2000 mm (+/- 150 mm) Total height 2800 mm Total length with 3rd axis 6300 mm Psdpfx Agjx Hpvzjzoha Total width 1500 mm Total load capacity 3000 kg Optional foot switch and wired remote control available upon request Please click the video Machine has been repainted, technically flawless

Condition: good (used), Container rotating device, welding rotating device, welding rotating device, welding device, welding rotary table, welding rotary and tilting table, welding rotating device Podpfxodwpdus Agzeha -Table: is tiltable -Maximum load: 75 kg -Clamping diameter: 300 mm -Hollow shaft: Ø 42.5 mm -Drive: 0.1 kW -Speed: RPM -Quantity: 1x welding rotator available -Price: per piece -Dimensions: 830/450/H920 mm -Weight: 174 kg

Condition: refurbished (used), functionality: fully functional, warranty duration: 3 months, type of cooling: water, welding current (max.): 400 A, For sale: ESAB Mig 4002cw 400 AMP 400 Volt Water-cooled 2/4 Step 4 Roller drive Program memory Steel – Stainless Steel Weldable Refurbished – Serviced – Tested Including Welding torch, earth work lead, gas cable, and 3 Months Warranty. Visits by appointment only. Test welding is possible. A video of the machine in welding condition is possible. Psdpfex Nwihjx Agzjha We also deliver to countries like Spain, Germany, Austria, Lithuania, Greece and all other countries inside and outside Europe with Euro pallets per freight. All our machines have been serviced and are 100% ready to use unless otherwise indicated. The pictures above show the real machine. We can also offer you other types of machines such as: Used, New, Mig, Mag, Co2, Tig, Pulse, AC/DC, Plasma, Water-cooled, Electrode, Brands we offer: OTC, Migatronic, Lincoln, Miller, Fronius, Kemppi, Parweld, Tico, Lorch, Rehm, Selco, Carl Cloos, Cebora, Esab, Saf, EWM, Ess, Kemper. You always do business with Cjays Lastechniek itself and never with third parties.

Condition: used, Toshiba VF-SX frequency converter for 0.4 kW motors. Untested, used. Phodpfx Agjvw Rnzezea Technical specifications: See pictures

Condition: like new (used), Year of construction: 2016, Technical Data: Robotic welding system featuring a 6-axis articulated arm robot with classic wrist and a 7th robot axis Robotic welding system with QIROX control V6A / QR-WPS-DH-TCS-10kN The robotic welding system has a total of 13 axes 7 robot axes, one axis extending the robot’s workspace by an additional 1200 mm, an asynchronous axis for station transfer, and two axes per station Offline laser sensor Torch changer system Maximum distance between rotation axis and support: 4500 mm Swing radius: 1050 mm Maximum workpiece dimensions: 4000 x 2000 x 800 mm Maximum swing weight without support: 500 kg Maximum swing weight with support: 1000 kg Two work positions: for loading and welding Power source: Qineo Champ 450A MIG/MAG welding: 450 A Extraction system incl. extraction hood: HERR Pjdew Idv Dspfx Agzjha Various partitions, safety barriers, and safety scanners Roboplan incl.: • Module tool change • Module macro technology • Module flat position Condition: As-new condition, very lightly used, approx. 10,000 operating hours The system is still assembled and can be inspected The seller accepts no liability for typographical or data transmission errors. The machine is in age-appropriate optical, technical and wear condition; used machines are sold without any guarantee.

Condition: used, Lot of 5 units WIG welding machines ESS model Thyrotig - Thyroplasmma 250 (DC) WIG welding machines in need of repair Year of manufacture: 1991 to 1994 Output: 250 Amp. = 60% duty cycle, 195 Amp. = 100% duty cycle Current type: DC Mains connection: 400 Volt, 50 Hz, 32 Amp plug - High-voltage ignition - 2-stroke and 4-stroke operation modes - Water-cooled - Some parts missing - Delivered without torch sets/hoses, scope of delivery as pictured Phjdpfx Agsw Hhbiszja Space requirements (L x W x H): 1200 x 570 x 920 mm Weight per welding machine: 255 kg Total weight for all 5 machines: 1,275 kg Three machines are operational. Two were kept in storage as parts donors. The units are no longer tested and are being sold as in need of repair.

Condition: used, Year of construction: 1980, outer diameter: 38 mm, pipe diameter (max.): 38 mm, PRODUCT (PROFILE, TUBE) .. external diameter min.: 11 mm .. external diameter max.: 38 mm .. wall thickness min.: 0.8 mm .. wall thickness max.: 2 mm LINE CHARACTERISTICS .. welding process: HF inductive .. sawing process: travelling .. speed max.: 120 m/min ELECTRICAL SPECIFICATIONS .. mains power supply: 440 kVA For sale is a fully serviced and excellently maintained tube welding line . The line was previously used for the production of USM Haller furniture tubes, but it is designed for a wide range of tube diameters, making it highly versatile for different manufacturing requirements. Welding is carried out with an induction HF system from EFD Induction, built in 2018, ensuring a modern and efficient welding process. Total line length: approx. 100 m Phjdpfjx Hd Thsx Agzoa Operation: handled by 7 operators Condition: well-maintained, fully operational Scope of delivery: complete package An excellent opportunity for companies looking for a reliable and high-performance tube welding line.

Year of construction: 1992, condition: good (used), Container turning device, welding turning device, welding turning device, welding device, welding turntable, welding turntable and tilting table, welding turning device, welding turntable tilting table -Manufacturer: Commercy Soudure, welding rotating device swiveling -Type: PM 250 -Load capacity: see photo nameplate Pedpjq Ei A Tofx Agzjha -Control: with foot pedal -Three-jaw chuck: Ø 314 mm, bore Ø 100 mm, base plate Ø 600 mm -Speed: max. 3 rpm right/left rotation -tiltable: via crank -Transport dimensions: 1190/720/H900 mm -Total weight: 267 kg

Condition: used, Year of construction: 2006, suction capacity: 10,300 m³/h, negative pressure: 4,400 Pa, Dust extraction unit, welding fume extractor, self-cleaning cartridge filter, pneumatic, vacuum unit suitable for plasma cutting, laser, sandblasting, soda blasting, shot blasting, and all types of dry dust. Brand: ESTA Model: DUSTEX F-126 The filter is cleaned by compressed air pulses during operation, ensuring high device efficiency. Psdpfxjx Hxycj Agzsha The fan is installed on the clean air side, minimizing the risk of explosion. Specifications: Max. airflow: 10,300 m³/h Max. negative pressure: 4,400 Pa Filtration surface area: 126 m² Cartridge filter elements: 6 pcs Motor power: 7.5 kW Inlet diameter: 315 mm Unit dimensions: Height: 3.70 m Width: 2.00 m x 1.35 m Base: 1.45 m x 1.02 m Stock number: 1095

Year of construction: 2004, condition: excellent (used), Technical specifications: System for welding longitudinal seams on steel beams with T- or H-profile, crane runway girders or bridge sections made of sheet metal - Max. boom arm height: 6,600 mm - Total length of the welding system: 6,700 mm - Horizontal reach of the boom arm: 5,000 mm - System runs on rails - Rail gauge: 2,065 mm - Submerged arc welding process (SAW) - SAW welding units - Power source: MESSER LG800N - Number of power sources: 2 units - Output: 400 amperes - Tack welding device Pjdpfxsxz Hu Io Agzjha The system is assembled and available for inspection under power in production. The seller assumes no liability for typographical or data transmission errors. The machine’s condition in terms of appearance, technology, and wear corresponds to its age; used machines are sold without any warranty.

Condition: good (used), Frequency converter, frequency transformer, drive converter, controller, variable speed drive Manufacturer: Mitsubishi, Freqol A024 frequency converter -Type: FR-A024-SO.4K-EC -Parameter Unit: FR-PU03E -Power: 0.4 kW -Input: 220-240 V 50/60 Hz Psdpfx Agjw S Ey Eozoha -Output: 2.5A -Dimensions: 140/130/H150 mm -Weight: 1.7 kg

Condition: good (used), Welding edge former, welding edge former, weld seam preparation, welding edge forming machine, edge milling device, edge milling machine, mobile milling machine -Bevel length: max. 20 mm Psdpfed Izt Sex Agzsha -Dimensions box: 460/360/H355 mm -Weight: 24 kg