Hand lever shears

Peddinghaus 3R 4

Condition: new, Year of construction: 2024, Roller for sheet metal unfolding. Working width: 1.250mm. Hsdpfedv Duwex Amtjt

Year of construction: 1965, condition: used, machine/vehicle number: 4447, working width: 2500 mm metal sheet thickness: 4 mm throat: 70 mm rear stop: 520 mm power: 380 V, 6,3 kW space needed: 3200 x 2300 x 1270 mm weight: 4600 kg Hedpjb H Ibuefx Amtot

Condition: used, Year of construction: 1978, sheet width 3100 mm plate thickness 2 mm rear stop 1000 mm cutting angle 1°06 ° no. of strokes 45 Hub/min total power requirement 3,0 kW Hodpfxsuagxps Amtjt dimensions of the machine ca. 3600 x 2200 x 1600 mm weight 4500 kg Equipment: - Electric motorized backgauge - With digital ELGO position display - Manual cutting gap adjustment - 1x side stop with mm scale - 2x support arms - 1x freely movable double foot switch - Front finger guard Special accessories included: - Pneumatic sheet metal holding device for thin sheet metal cuts

Year of construction: 1972, condition: used, machine/vehicle number: 32 416, max. working width: 1530 mm for metal sheets up to: 2,5 mm opening width top clamping bar: 290 mm adjustment bending cheek: 90 mm clamping bar drive: 1,1 kW below cheek drive: 3 kW rear stop: ja mm Hodpoy Np Aefx Amtet weight: 2200 kg space needed: 800x3000x1380 mm

Condition: excellent (used), gear motor, electric motor, electric gear motor, spur gear motor -Condition: unused -Manufacturer: SEW-Eurodrive, spur gear motor -Type: RF97 DRN132S4/TF i27.58 -Speed: 53 rpm -Power: 5.5 kW -Shaft: Ø 60 x 90 mm -Protection class: IP54 Hedpfx Amst Uluyjtjt -Quantity: 2 pieces available -Price: per piece -Dimensions: 860/350/H410 mm -Weight: 170 kg/piece

Condition: new, Year of construction: 2025, rotational speed (max.): 50 rpm, - Ring bending machine Hjdpolp Ryhjfx Amtst – Shaft diameter 50 mm – The upper roller is hydraulically driven – Digital display – Can be used horizontally/vertically – Foot control – Emergency stop – Documentation – 400V

Condition: new, Year of construction: 2025, Window drip cap roll forming machine PO-1 allows to produce “window trim” profile by rolling the sheet metal through forming rolls. A window trim is an element that is widely used in construction while windows installation. In the standard way the window trim is bent step by step using a manual folding machine. This is a cheaper, but more time-consuming process. The metal sheet must be pre-marked for each bending operation. Each bend is then performed using a manual bending machine. The operator must set the necessary dimensions according to the marks, fix the sheet metal with the machine"s fixation mechanism, and then bend it. The length of the window trim is limited to the maximum working length of the bending machine. Thus, each manual folding operation is time-consuming and the production process becomes expensive and inefficient. To improve the production process we offer the window drip cap roll forming machine PO-1. This machine rolls the window trim profile on both sides simultaneously in a single operation. The rolling speed is 10 m/min. The machine is equipped with 7 pairs of forming rolls. The minimum width of window trim is 120 mm when rolling on both sides at the same time and the maximum width is 610 mm. To change the width of the window trim, simply use the adjusting handle, which makes it very easy to adjust the machine to go from one trim width to the next. Thus, the adjustment process is not time-consuming. It’s also possible to roll the window drip cap on the machine in two steps. Hjdpfx Aelwt Adomtst

Condition: used, Hydr. guillotine shears SAFAN type VS 310 / 4 Machine. No. B7140 Year of construction 1984 Cutting length 3100 mm Cutting thickness 4 mm Back gauge 900 mm, accuracy +/- 0.5 mm Angle fence front left 2100 mm Hedpfx Amsumpq Netst Hydraulic tank capacity approx. 120 liters Drive power 7.5 kW Mains connection 400 Volt, 50 Hz - Motorized back gauge with positioning control and digital position display - Single stroke and continuous stroke with adjustable stroke pause - Cutting angle adjustment - Manual cutting gap adjustment - stepless cutting length adjustment - Cutting line lighting - 17 Hydraulic sheet hold-down device - Angle stop left with scale 2100 mm - 2 material support arms 1600 mm - 2 material support arms 615 mm - Electric foot switch - Fixed finger guard in front of the hold-down devices Space requirement without sheet supports L x W x H 3850 x 2300 x 1680 mm Machine depth with sheet supports 3900 mm Weight 5.7 tons good condition

Condition: good (used), functionality: fully functional, Year of construction: 1975, sheet thickness (max.): 4 mm, power: 22.06 kW (29.99 HP), cutting length (max.): 2,500 mm, Old but well-maintained machine Hsdsr Nvf Uopfx Amtot

Condition: good (used), Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Outer tube diameter: 168 mm -Piston rod: Ø 80 mm Hsdpfx Amsb A H Rvstot -Stroke: 420 mm -Piston rod mount: Ø 40 mm -Piston diameter: 140 mm -Measurement eye to eye: 770 mm retracted -Measurement eye to eye: 1190 mm extended -Quantity: 2 pieces available -Price: per piece -Weight: 75 kg