New open Sorting line. 6 working places.

ProSort

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Gijdpfx Ajvwlqqog Tsl Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2006, operating hours: 15,000 h, condition: good (used), For sale is an Erema 1007T. Year of manufacture: 2006 Gjdsumubyspfx Ag Tsil Operating hours: 15,420 Throughput: 250-350 kg/h Currently, the system is used to process HDPE, but it is also suitable for other plastics such as LDPE. The system can be viewed during operation. A new extruder screw was installed in February.

Year of construction: 2019, condition: as good as new (ex-display), Aluminum flat conveyor including substructure. Dim: 6000 + 620 x 105mm Conveyor belt width 500mm PVC conveyor belt incl. Studs, sidewall and sealing tape V2A feeding hopper at the beginning of the conveyor belt. Giodpfx Ajd Ra Uasg Tol * optional with magnetic deflection roller at the end of the conveyor belt. * optionally available as a climbing conveyor * Special designs in all versions possible.

Year of construction: 2024, condition: new, ZIGZAG air separators Application description: ZIGZAG type air separator is a device designed to purify materials in the waste recycling process. The separator separates light fractions from heavy fractions by pneumatic method. It works well with a wide range of waste materials of 0-150mm size. Air separators of this type are used for pre-ground, jagged or very fine materials. Thanks to our unique design, the separator has the ability to adjust at many points that are important for the purity of the received fractions. ZIGZAG type separators are used in many areas: weight classification of metal granules purification of shredded scrap from the light fraction (films, plastics, paper) removal of volatile fraction during recycling of WEEE Giodpfsua D Aljx Ag Tel purification of plastics, rubber purification of municipal waste, glass removal of dust Construction description: The ZIGZAG separator consists of individual components mounted on a common support structure. In the first part, the ZIGZAG module is installed. The module has an inspection hole and regulation of the material stream passage gap. In the second part there is a cyclone discharging the light fraction. Underneath the cyclone there is a variable speed sluice for ejection of separated materials. A fan with electronic speed control is located on top of the structure. The structure is designed in part for loading and unloading by conveyor belts. The separator has a control cabinet equipped with a safety system.

Condition: not inspected (used), Hydraulic press for pressing paper etc. materials. The device was operational before disassembly. Gsdpfsh Nyfyjx Ag Toil Press dimensions: length 4850 mm, width 1370 mm, height 3000 mm (possibility of reduction 2300 mm). Weight 3500 - 4000 kg. If you have any questions, please contact us at 539 660 495.

Condition: new, Year of construction: 2025, machine/vehicle number: 180965471, Additional options and accessories Notes Mobile impact crusher on crawler track The K1 impact crusher with tracked undercarriage, the new addition to the product range with impact mill with a capacity of 250 t/h . Can be equipped with closed circuit re-screening to perfectly calibrate the final product. It is appreciated for the excellent quality of the crushed product and also gives its best in terms of operating economy. Production capacity: approx. 250 TO/H Proportional distributor with \"Load Sensing \" for optimization of the system and reduction of fuel consumption by approx. 30%. gap hydraulically adjustable even during the crushing operation fast blocking system with wedges and folding cylinders dust extraction system tank pump magnetic separator warranty 1 year up to max. operating hours from start of operation of the plant Technical data: Giodpfx Agshd Nais Tol Impact crusher type M x 700 mm Crushing gap from 30 (20) to 100 mm (gap adjustment to 20mm only possible with 3rd grinding track) Feed hopper 4 m³ - 1800 x 3700 mm Grizzly feeder 900 x 3400 mm Main conveyor belt 800 x 9600 mm 4 cylinder diesel engine with constant speed 82 HP/60 KW , exhaust gas stage V Control panel chain drive 400 x 2900 mm Weight: kg Transport length 12560 mm Transport width:2550 mm Transport height 3200 mm More information Purpose: construction, General condition: very good, Technical condition: very good, Visual condition: very good,

Year of construction: 2024, condition: new, Overview - of the different variants *Not every position is required: Optional: -Bale shredder MHB from 24.990 € net -MHZ straw mill from € 7,980 net -Special hopper 970 € net -Cyclone from € 3,750 net -Sheet metal silo demonstrator with discharge (only sketched in the picture) *optional, if you want to load with the wheel loader Unit price net from € 14,750 - Demonstrator -Dedusting auger - length approx. 4 m 4 sieves are mounted on the underside, which are extracted. Unit price net from: 9.750 € - Extraction parts / hoses flat rate 945 € net - Complete control system Net unit price: € 2,750 -Demonstrator extraction unit MMJET 160 Demonstrator, with cleaning Connection 160, fan 2,2kw air capacity 1850m³ /400 V Automatic compressed air cleaning Unit price net from: 6.950 € -Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with + - 20 kg from 59.995 € net *A reference system (baler) is located in zip code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height can be adjusted on request) Bale weight +/- 20 KG (depending on material) Capacity: approx. 30 bales per hour Storage container approx. 0.7m³ capacity Gjdpfxsff Sbio Ag Tjil Filling level sensors for min./max. filling level in the container Hydraulic pre-compressor Hydraulic compression ram Hydraulic unit, valve block with oil tank Pump 18.5 KW / 50 liters Rollers in the bale chamber for easy bale push-off Dimensions (l x w x h) 3105x2830x2455 mm Weight approx. 1500 KG mütek baling presses / wrapping machines are designed for the production of bales from a wide variety of materials such as shredded micanthus or elephant grass, wood chips, sawdust and shredded straw. straw. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. quality in continuous operation. The baler compacts the material filled into the storage container without the addition of binding agents and packs the material into plastic bags. The volume of the material can be considerably with the baling press. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18 % Atro. The container of the mütek baler can be fed automatically or manually and has a volume of approx. 0.7 m³. volume of approx. 0.7 m³. Containers with a larger volume or with an attached suction and filter system as a complete disposal unit are also available. In addition to automatic filling via deduster, mütek also offers filling by means of screw conveyors. With both variants, automatic automatic dedusting is possible. mütek baling presses are equipped with a control cabinet for the control system. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adapted to your requirements on request. The following advantages arise in the production of bales: - simple and safe storage - No loose dust - Minimization of the storage volume - Low transport volume *Requirements for source material: - dry (max. 30 % ATRO) - Maximum length 35 mm

Condition: used, Year of construction: 2003, Technical details: pressure: 40 t box opening: 1200 x 730 mm material: Pappe,Plaste - cardboard bottles voltage: 400 / 50 V / Hz total power requirement: 16,4 kW transport measurements machine: 6,5 x 6,2 x 2,7 m Fully automatic hydraulic CHANNEL BALL PRESS for recycling with conveyor unit/conveyor belt LxW: 4500x1000mm motor driven with automatic binding unit 3-fold bale count display/counter bale chamber LxWxH: 1800x800x800mm with 1,2m³ volume bale size LxWxH: 800x800x300-1600mm Filling opening LxW: 1200x730mm: Filling height 1200mm Hopper size LxWxH: 1200x1200x1400mm; filling height 2500mm Gjdpfx Asu Nw Ezjg Toil *

Year of construction: 2006, condition: like new (used), Container volume 32 m3 Gsdpefhb Tkefx Ag Teil

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. Godpfx Aovgrh Uog Teil The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH