Decoiler

Sestal S.C. 6T - 1250

Condition: new, functionality: fully functional, Year of construction: 2025, control type: PLC-controlled, degree of automation: automatic, actuation type: manual, coil inner diameter: 510 mm, coil weight: 6,000 kg, coil width: 1,500 mm, power: 4 kW (5.44 HP), input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, Brand New 6T-1250 Hydraulic De-coiler 6-ton X1250MM hydraulic tensioning, power feeding, with loading trolley and pressure arm Lredpfsw Nfi Uox Ab Tjh Hydraulic tensioning of steel coil inner hole, oil pump power: 2.2KW Inner diameter of steel coil: 510 ± 30mm, maximum outer diameter of steel coil: 1500mm Load bearing capacity: Max 6 tons Core shaft diameter: 203mm Side panel: A3 panel, integral, side panel thickness 18mm Steel coil width Max.1500mm Wedge type tensioning, 4 claws Rotating oil cylinder, with the core shaft rotating simultaneously Gear head reduction motor, motor power 4.0KW, matched with main machine forming speed 25M/min Delta inverter The pneumatic clamping arm at the top of the feeding machine prevents the steel coil from loosening, and the air valve control action is controlled by electronic control Direction of the compression arm: When facing the core axis, the compression arm is on the right side; Self stop device controls the start and stop of steel coil rotation 6-ton feeding machine trolley 4-column design The car is moving on the I-beam at the bottom of the feeding machine Up and down travel distance of the car: Max 350mm Front and rear travel distance of the car: Max. 2000mm Voltage: 380V/50Hz/3Ph

Condition: used, Year of construction: 1980, machine/vehicle number: A-07/471A, sheet width - max.:130 mm straightening roll diameter:40 mm :5 :2+2 sheet thickness - min.:0,4 mm sheet thickness - max.:3,5 mm Lsdpscxxx Rsfx Ab Tsrh weight:0,4 t dimensions of the machine ca.:0,6x0,65x1,15 m with integrated, stepless adjustable Vari-drive, reversing, operating-mode switch for manual and automatic operation, introduction roller cage, position indicator of straightening rolls via analogue display, adjustment of straightening rollers via hand wheels, automatic swivel arm control, very good condition

Condition: good (used), Year of construction: 2005, URBAN Welding and Cleaning Line type CC 16/43-26/23 consisting of Welding Machine AKS 1600 and Polishing Machine SV 430. Ledpfx Aevyqbmjb Terh

Condition: used, Year of construction: 1997, functionality: fully functional, type of input current: AC, Glass tempering furnace EFCO, 1500x3000 1500 x 3000 mm, Right – Left Year: 1997. 415 V, 50 Hz, 3 Ph. In good technical condition. Disassembled and ready for loading. Lodpfsxguqnsx Ab Torh

Year of construction: 2009, condition: used, material width 320 mm material thickness 8 mm Lrjdop U Uwiepfx Ab Toh no. of straightening rolls 9 material cross-cut 2000 mm² weight of the machine ca. 4,2 t dimensions of the machine ca. 2000x2000x2400 mm

Condition: excellent (used), functionality: fully functional, Year of construction: 2017, operating hours: 49,641 h, control type: CNC control, actuation type: hydraulic, controller manufacturer: Bystronic, bending force (max.): 40 t, working width: 60 mm, stroke length: 200 mm, oil tank capacity: 100 l, travel distance X-axis: 300 mm, back gauge speed R-axis: 500 mm/s, back gauge travel distance R-axis: 100 mm, back gauge travel distance Z-axis: 955 mm, Equipment: CE marking, documentation/manual, emergency stop, finger protection, safety light barrier, Used Bystronic Xpert 40ton x 1metre cnc pressbrake for sale Model: Xpert 40/1030 Tonnage 400 kn Bending length 1030 mm Standard stroke [S] 200 mm Open height [D] 515mm Distance between side frames 1060mm Table Width 60mm Max. back gauge range X-axis 500mm X-axis travel 300 mm X-axis speed 1500 mm/s R-axis travel 100 mm R-axis speed 500 mm/s Z-axis travel 955 mm Z-axis speed 2000 mm/s Y-approach speed (up to) 300 mm/s Y-working speed (up to) 25 mm/s Accuracy Y-axis 0.004 mm Oil capacity 100 l Electric supply 7.5 kw Weight 4t Length, approx. [L] 1520 mm Width, approx. [W] 1584 mm Height, approx. [H] 2449 mm 1.1 Xpert 40/1030 1.2 ByVision Bending control with 22 Inch Full HD display and touch technology Lodoxtf A Iopfx Ab Torh 1.3 Dynamic drive system (DDS) with Energy Saver 1.4 Automatic tool protection 1.5 Ergo foot switch 1.6 Rear protection sliding door electrically controlled 1.7 User manual (on CD) 1.8 Ambient air temperature 7°C up to 35°C 1.9 Voltage: 400/480 V, 50/60 cycles, 3 Ph (other parameters available on request)

Condition: used, Technical details: plate width: 800 mm coil weight: 12 t sheet width - max.: 800 mm sheet width - min.: 300 mm thickness of strip/band: max. 5,0 mm band speed: 4,5 / 25 m/min work height max.: 1700 mm Payload: 12,0 to (Coil) Weight approx.: 7,3 + 6,62 t dimensions of coil: 3,2 x 1,9 x 2,7 m dimension machine xH: 2,5 x 2,6 x 2,45 m Decoiler with loading device Can optionally be sold together with stock no. 0100571. straightening unit: Infeed rollers: 2 x Ø 144 x 850mm Straightening rolls: 3 x bottom rolls, rigid, Ø 100 x 850mm, 30mm adjustable 3 x top rollers, Ø 110 x 850mm; 30 mm adjustable Coil unwinding machine: Outer Ø 1.500mm Strip width max. 800mm Load capacity max. 12 to Clamping Ø 470 - 630 / 570 - 730mm Transport unit LxWxH: 1700 x 1500 x 1000mm; crosswise running, with prism support 1000 x1000mm Machine will be offered and sold with Stock no. 0100521 as a decoiling and streightening line. Lsdpfx Abeu Ic Ave Torh *

Year of construction: 2021, condition: like new (used), functionality: fully functional, Vertical infeed transport - Vertical 2600 mm washing machine with drying - Tilting table (behind the washing machine) - Horizontal outfeed transport Pos. 1 Loading station, 250kg With the help of the suction frame, the sheets are taken off the glass rack and they are placed vertically on the tilting table in front of the washing machine. Differences in inclination can be compensated by tilting of the suction frame. The suction frame has a rotating function to collect short formats in upright position and to place them down on the long edge. Light crane Trolley crane with a lift system travelling on rails by hand, which are standing on steel supports. Lift Electrical lifting and lowering, horizontal turning and tilting of loads. Generation of vacuum via vacuum pump system with check and display of the vacuum power. A central operation desk with integrated control buttons allows easy signal activation of the single functions. In case of pressure loss in the dangerous area, it is displayed and acoustical signal is given. Lrsdotwphwjpfx Ab Tjh Pos. 2 Vertical Inlet Transport WM The vertical transport serves as inlet transport in front of the washing machine. In horizontal position, the glass sheets are placed on Vulcan transport rollers. In vertical position transport rollers with Perumaan rings are driven via screw wheels. The transport rollers are arranged in drag bearings placed on a solid welded frame. Small glass sheets are placed manually on the transport frame. After placing the glass sheet, the transport is activated by push button. Pos. 3 Vertical Washing Machine with Drying The washing machine body, washing chambers, recirculation vats and the drying nozzles are made entirely of stainless steel. The rubber rings of the transport rollers are resistant to cutting oil. Flat jet spraying nozzles in the pre-rinsing section are fed with city water. Coarse dirt particles removed are directly led into the drain. This reduces contamination of the DI-water circuit for the washing machine. The washing machine is equipped with energy and water saving cascade system. Pre-rinsing section with Flat jet spraying nozzles Washing section with 3 pairs of brushes, 3 vats and 3 pumps Acid section with 1 pair of brushes, 1 vat and 1 pump Drying section with 2 pairs of drying nozzles provide dry edges. Pos. 4 Vertical Inspection Transport with glass Activation Section The transport serves as Activation Section for the glass surface and as Inspection and Storage Transport before the Tilting Table. Drive by a geared motor, A.C., frequency controlled. All the rollers are arranged in drag bearings with a single drive operating pairs of spiral-toothed gear wheels. The transport rollers are vulcanized and ground. Pos. 5 Tilting Table with Horizontal Transport and Vertical Inspection

Condition: good (used), Year of construction: 2009, functionality: fully functional, number of straightening rollers: 7, coil weight: 4,000 kg, coil outer diameter: 1,500 mm, number of feed rollers: 2, straightening roller diameter: 80 mm, coil width: 600 mm, 1. Decoiler Type: MS 4000 Coil weight: max. 4.000 kg Strip width: max. 600 mm Outer diameter: max. 1.500 mm Lrodpfjq A Tw Rox Ab Tsh Inner diameter: 475 – 535 mm Execution: • Hydraulic expansion • Hydraulic pressure arm from top with hydraulic driven roll Rolle • Lateral swivel in roll on front side, disc at back side and additional 3 pc. single arms for coil keeping • Mandrel driven by electric motor, control by light sensor • Decoiler moveable for loading by hydraulic • Coil loading table 2. Straightening maschine Type: MR 58 Strip width: max. 600mm Stock thickness: 0,8 – 3,6 mm at rigidity 400 N/mm2 Straightening rolls: 7 pc., supported Pulling rolls: 2 pc. Diameter of rolls: 80 mm Speed: 5 – 30 m/min Execution: • Hardened and ground rollers • Pneumatically lifted feed roller • Straightening rollers adjustable as a block • Lateral strip guiding at infeed, manually adjustable via hand crank • Hydraulic strip insertion aid (support table, extendable tongue and pressure roller from above) • Straightening head can be opened (alligator mouth) • Ultrasonic sensor for loop control • Swivel control panel • Siemens S7-200 control system

Condition: good (used), functionality: fully functional, number of straightening rollers: 7, coil outer diameter: 1,400 mm, coil inner diameter: 508 mm, roller diameter: 80 mm, number of feed rollers: 2, feed roller diameter: 80 mm, straightening roller diameter: 80 mm, coil width: 400 mm, load capacity: 3,000 kg, 1. Decoiler Make: Dimeco Model: 2371 E-FPS Year of manufacture: 2006 Load capacity: max. 3 tons Strip width: max. 600 mm Expansion range: 470 – 530 mm Coil outer diameter: max. 1,400 mm Equipped with: • Hydraulic expansion • Pneumatic hold-down roller from above • 6 strip edge guide arms • Pneumatic disc brake 2. Straightening Machine Lrsdpotgvgpofx Ab Toh Make: Dimeco Model: 1676 C-VV Year of manufacture: 2000 Strip width: max. 400 mm Strip thickness: 0.8 – 4.5 mm Number of straightening rollers: 7 Number of entry and exit rollers: 2 each Roller diameter: 80 mm Equipped with: • Frequency-controlled drive • Hydraulic strip feeding aid with support table, feed tongue, hold-down arm from above • Pneumatically liftable entry roller • Lateral strip guide rollers • Pneumatically swivelling strip transfer table between straightening machine and feeder