Clamping angle

Stankoimport 500 x 200 mm

Condition: used, Technical details: balancing body max.: 800 kg balancing body diameter: 1250 mm Balancing revolution per minute: 190 - 3600 U/min bed length: 2600 mm voltage: 380 V/Hz drive power: 7,5 kw Weight approx.: 1,5 t dimension machine xH: 3,5 x 1,7 x 2,0 m dimensions electric cabinet: B:650 x T:250xH:800 mm Djdpfxeu Upp To Aglscb Horizontal balancing machine The balancing machine is used to measure and balance the static or dynamic unbalance of rotors. Balancing body weight max. 800 kg with equal load distribution, i.e. 400 kg per bearing pedestal Power transmission by means of cardan shaft Bearing journal Ø min./max.: 16-95 / 95-180 mm Bearing distance center distance min. 125 mm and shaft end bearing center max. 2070 mm Measured speed: 1st gear = 190 - 650 rpm. 2nd gear = 400 - 1250 rpm 3rd gear = 700 - 2100 rpm. 4th gear = 1200 - 3600 rpm. 2 pick-up blocks whose displacement is manual over the entire bed Schenk measuring device with digital display and some accessories, e.g. many rotor shafts with different Ø and different rotor mounts, please ask! *

Condition: good (used), Year of construction: 2000, total height: 47,000 mm, total width: 27,000 mm, total length: 25,000 mm, table width: 1,000 mm, table length: 1,800 mm, overall weight: 43,000 kg, ram plate width: 600 mm, die cushion stroke: 200 mm, Siemens Simatic OP 27 control system Light barrier Sick Separate control cabinet Ritta Side passages Ground level installation Djdpfstiwgiex Aglecb

Condition: used, Year of construction: 1987, pressure / t stroke / mm table-size / mm weight of the machine ca. 65000 kg Make: Shepherd Type: SVRM Dedpfx Ajuddcaoglscb 4-roller bending machine: Year of construction: 1986 Working width: 3000cm Smallest pipe diameter with 600 mm roller: Ø 720 mm Smallest tube diameter with 360 mm roller: Ø 460 mm Sheet thickness up to (depending on the material): 50 mm Material SA- 738 B Working width: 2500 mm Material SA- 738 B Material thickness: 35 mm conical bending: Except for the top roller, all rollers can be moved in an inclined position for conical bending. The roller positions can be read on display instruments. For semi-automatic or fully automatic operation of the machine, the bearing jewels of the rollers are equipped with scale bars and slide cams for limit switch actuation. This allows the rollers to return to the same set position over and over again, giving a very high level of uniformity in the shot wefts being bent.

Condition: used, Year of construction: 1973, pressure 200 t chamfer lenght 3600 mm distance between columns 2650 mm dayligth 500 mm throat 300 mm stroke 250 mm working feed 10,5 mm/sec return speed 100 mm/sec ram stroke speed 150 mm/sec table height 900 mm oil volume 500 l total power requirement 37 kW weight of the machine ca. 17800 kg dimensions of the machine ca. 3710 x 1800 x 3390 mm Equipment: - Controlled axes Y1 + Y2 - Manual X-axis with digital position display Dcedpfjt I D U Ejx Agleb - Set of upper and lower tools - 2x stop fingers - 2x front support arms - Hand and foot controls - Side + rear safety guard - Operating instructions

Condition: used, Year of construction: 2007, pressure 315 t distance between columns 1750 mm stroke 700 mm distance table/ram, max. stroke up, adjustment up 1200 mm table surface area 1600 x 1500 mm pressure of drawing cushion in table 125 t stroke of drawing cushion in table 200 mm die cushion area 1200 x 1400 mm table height over floor 750 mm ram surface 1640 x 1500 mm power requirement 55,0 + 11,0 kW Dcjdpsvuukbofx Agleb weight 29,5 t dimensions (WxDxH) 3,2 x 4,5 x 5,8 m Height above floor 5,1 m year of manufacture 1983 - 2007: modernization of electrical control (Siemens S 7) permitted for manual put-in according to the CE Regulations with oil-hydraulic drive, hydraulic drawing cushion in table, hydraulic cutting impact cushioning can be offered without putting into operation, with putting into operation in given condition or alternatively with new control Siemens S 7-1500 F

Condition: good (used), Year of construction: 1978, machine/vehicle number: 11.542, Offer 24559 Technical data: - max. working width 1100 mm - max. cutting performance - at 400 N/m² strength 20 mm - cutting angle 1 ° 30 ` - cutting gap adjustment via hand lever - number of hydraulic hold-downs 7 pcs - manual back stop 10 - 1000 mm Dcodpfxsvmmrus Agljb - front angle stop - front support arms - stroke rate 13 per/min - drive 400 V / 45 kW - table height 700 mm - space requirement including back stop, without front support arm - approx. W 2100 x H 2250 x D 2250 mm - weight approx. 7500 kg - with: - electric foot switch - cutting line lighting

Condition: used, Year of construction: 2007, pressure 100 t stroke 500 mm table surface area 900 x 600 mm Dcjdsvprv Ropfx Aglob rapid traverse 22 mm/s stroke speed 2 mm/s ram surface 700 x 350 mm total power requirement 2,2 kW weight of the machine ca. 1,6 t dimensions of the machine ca. 1,9 x 0,85 x 2,3 m The machine is of the Italian make SICMI, which was traded by the Knuth company.

Condition: used, MULLER 250t PRESSURE: 250t Dcederfxhkjpfx Aglob STROKE: 550mm TABLE DIMENSIONS: 2500x1400mm

Condition: used, functionality: fully functional, Year of construction: 2007, punching force: 80 t, Hydraulic Punching Machine GEKA Brand: GEKA Model: HYD 80 S Serial No.: 14981 Year: 2007 Punching force: 80 tons Dcedpjxgdf Ujfx Aglob Number of stations/positions: 5 workstations (the machine allows for 2 simultaneous work positions in the Hydracrop series). Throat depth (S version): 300mm Punching capacity (typical examples): up to Ø 40x14mm Flat bar shearing: e.g. 450 × 15mm Profile cutting (L angles): typical values around 130×130×13mm Round: 45mm Square: 45mm *Delivered with 10 sets of punches and dies No.6 from 4 to 28mm of your choice

Condition: used, Year of construction: 1983, Technical details: Pressure: 160 t throat: 360 mm max. ram stroke: 500 mm distance table/ram: 800 mm clamping plate on table: 1250x630x100 mm passage opening in table: 4x Ø 62mm mm ram speed - forward: 200 mm/s ram speed - reverse: 125 mm/S ram surface area: 450 x 850 mm mortise hole in ram: Ø 49 mm height over floor: 810 mm total power requirement: 17 kW weight of the machine ca.: 7200 kg dimension machine xH: 2,1 x 1,4 x 3,4 m manual counter Dedpfx Aju Nfvusgljcb *