Extrusion Plant

Artec 145DV

Year of construction: 2003, condition: reconditioned (used), Stock - No. 2651 1 used underwater pelletizing unit, partially overhauled in 2023 Throughput up to approx. 450 kg/h depending on the material, consisting of: Type BKG ( Nordson ) Start-up valve with hydraulic station Granulator type A300 including die-plate and cutter bar, drive 4.4 kW by-pass system TVE 1000 ED pellet-dryer drive 4 kW incl. Agglomerate catcher Tempered water system with Water box 200 liters, installed heating capacity 9 kW Water pump 2.2 kW with 15³/h heat exchanger Control unit - NEW Further UWP pelletizing units are available ex workshop in Wuppertal-Germany ( as Gala, BKG Nordson, Econ ) Available from the Wuppertal warehouse: complete compounding, pelletizing extrusion lines, with single-screw or twin-screw extruder. Dusdpfeiyyf Iox Anwst

Condition: excellent (used), functionality: fully functional, Werner & Pfleiderer Twin-Screw Extruder ZSK 40 – Excellent Condition For sale is a Werner & Pfleiderer (WP) ZSK 40 co-rotating twin-screw extruder. Technical Specifications: • Machine Type: ZSK 40 • Screw Diameter: 40 mm • Screw Length: 7 barrels × 4 D → approx. 28 L/D • Main Drive: 34.5 kW • Motor Speed: 1,800 rpm • Screw Speed: 40 – 400 rpm • Max. Torque per Screw Shaft: 325 Nm • Heating: Electric, connected load approx. 17 kW • Cooling: Water chiller unit • Temperature Control Zones: 6 zones • Barrel Temperature Sensors: 6 • Material Temperature Sensor: 1 • Material Pressure Sensor: 1 Barrel Configuration: • Feed barrel with liquid injection port • Open barrel with insert and 2 liquid injection ports • Multiple closed barrels with ports for liquid injection or measurement points • Degassing barrel General Features: • Co-rotating, closely intermeshing (self-cleaning) screws • High mixing and dispersing performance thanks to modular mixing and kneading elements • Modular system for screws and barrels • Drive section and process section mounted on stable base frame Fields of Application: • Plastics compounding • Masterbatch • Additive and filler incorporation Duedpfx Anjycuuyswjt • Laboratory and pilot plant use • Formulation and product development Condition & Runtime: According to the operating hour counter, the machine has run for less than one year and is therefore in excellent, nearly as-new condition. The screw elements are also as new. Options & Customizations: Upon request, we can design and install suitable tooling, such as strand dies, and integrate additional peripherals such as screen changers, pelletizing units, dosing technology, or other customer-specific components. The machine can thus be configured and delivered ready-for-operation according to customer requirements.

Condition: ready for operation (used), Used Machine Injection Moulding Machine Manufacturer: Krauss Maffei KM 80 C1 Dusdpfju Ti Srsx Anwst Year of manufacture: 2000 Only 1 machine left in stock No delivery time, immediately available Inspection possible by appointment The machine is no longer powered / No coolant connection The machine is professionally stored Technical Data: Clamping force (kN): 800 kN Platen size (mm): 610×610 Tie bar spacing (mm): Daylight opening (mm): 250 Max. (mould) open daylight (mm): 750 Control unit: MC4 Screen text language: German (cannot be changed to other languages) Injection unit: Screw diameter (mm): 45 Injection pressure (bar): 1878 Shot volume (cm³): 275 Pump drive power (kW): 18.5 Heating capacity (kW): 13 Oil tank capacity (l): 270 Dimensions (m): 4.3 x 1.4 x 2.1 Total weight: 3.2 t Further photos available on request.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l Dusdpfjvf E Avex Anwet SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 2016, condition: excellent (used), functionality: fully functional, Make: Reifenhauser Model: Mirex-MT-V 1-RZE 120-1800 Year: 2016 Condition: Excellent Use: PET / PP / PS Foil or Sheet PET: Thickness Range: 0.25 - 2.2mm Dedpfxevbcbus Anweut Output: 2,000 kg/h Max Sheet Width: 1600mm Extruder: RZE 120mm Electrical Supply: 3 x 480V 60Hz with N Calendar Roll Width: 1800mm Calendar Roll Diameters: 450 / 700 / 700mm Silicon Bath Max Sheet Width: 1600mm Silicon Bath Sheet Thickness Range: 0.15 - 1.5mm 4 Position Winder WOB 1800 for double web winding included. All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale.

Year of construction: 2017, condition: ready for operation (used), Material throughput: LDPE: 110kg/h, PA6.0/LDPE/EVOH: 150kg/h, PP/PA6.0/LDPE/EVOH: 135kg/h, PA6.0/LDPE: 120kg/h, EVA/LDPE: 150kg/h. Nominal output: 77kW, PCU output: 30kW, extruder output: 18.5kW, motor output: 10.7kW, heating zones: 1, heating output: 12kW. Documentation available. On-site inspection is possible. Dujdpfx Anowty Hkewot

Year of construction: 2007, condition: excellent (used), EXTRUDEX EXTRUDER EN50-30D year 2007 no. 4101264, with melt pump, screen changer and 5 layer pipe head Year of manufacture 2007 As well as 4 co-extruders EXTRUDEX EN25-25D, year of manufacture 2007 APPLICATION: Production of PE 5 layer pipes Dsdpovyaxusfx Anwsut Max diameter 32 mm INVENTORY: 1 single-screw main extruder EN 50 4 co-extruders single-screw auxiliary extruders The extrusion system is my property Location: D-26345 Bockhorn-Grabstede, Bahnhofstr 6, Germany

Condition: used, Year of construction: 1994, operating hours: 62,058 h, functionality: limited functionality, machine/vehicle number: 099314, bale width: 770 mm, bale height: 520 mm, Manufacturer: COMDEC - PAAL Model: LV2020PFT Serial number: 099314 Year of manufacture: 1994 Maximum capacity: 25,000 kg/h Bale discharge dimensions: 77 cm x 52 cm Dodpfx Anjt Ucqfjwsut The press was in operation until the production line was shut down.

Condition: defective spare-parts repository (used), Year of construction: 2013, Manufacturer: HSM Tip: HL 4010 Li Year of construction: 2013 The equipment is incomplete and is sold as a part Fault: Hydraulic pump missing Control is missing Power supply unit missing Dsdpfour Ravsx Anwout

Condition: new, Year of construction: 2025, Suction port diameter: 1 x 200, 3 x 100mm Nominal volume flow: 1760 m³/h Residual dust content: 0.1 mg/m³ Chip collection volume: 240l Dusdohpmawepfx Anwet Filter cleaning: motorized motor power: 3 kW Noise level: 78dB(A) Machine length: 1340 mm Machine width: 900 mm Machine height: 2170 mm Weight: 178 kg