Paint mist extraction

Braun&Toth BTFW 2020

Condition: excellent (used), Year of construction: 2011, HURCO TMX8MYS H-TS8034 Year of manufacture: 2011 Dedpfxjxg D A Hj Ahnouu

Condition: used, Year of construction: 2000, cutting diameter 280 mm saw band length 4930 mm capacity 90 degrees: square 280 x 280 mm capacity 45 degrees: round 280 mm capacity 45 degrees: square 280 x 280 mm capacity 60 degrees: round 220 mm capacity 60 degrees: square 200 x 200 mm feed length 600 mm feed length: multiple 5400 mm cutting speed 17 - 90 m/min length of rest piece min/max min. 30 mm saw diameter min. 10 mm control KASTO, Compact Control total power requirement 5 kW Dsdjw En Efjpfx Ahnjuu weight of the machine ca. 1,75 t dimensions of machine L x W x H 2,68 x 2,54 x 1,59 m Accessories: coolant, roller track 3300 mm length, 300 mm width; roller track 1350 mm length, 300 mm width

Year of construction: 1963, condition: ready for operation (used), Load: 18t, lifting height: 10,750mm, span: 23,000mm, weight: 35.1t, machine was regularly maintained and inspected. Djdpfjh I Edvsx Ahneuu

Condition: refurbished (used), Year of construction: 2011, Used automatic hydraulic bandsaw for metal MEP SHARK 332 NC EVO Blade dimensions: 3320x27x0.9mm Mitre angle: from 45° to +60° Operating modes: manual, semi-automatic dynamic, semi-automatic, automatic Cutting speed: 15-100m/min (inverter) Cutting capacity: at 0° - round 300mm - square 260mm - rectangle 330x260mm Dimensions: 2600x2320x2000mm Year of manufacture: 2011 Weight: 1050kg Djdpfx Asul Svlohnouu The machine is fully refurbished and tested.

Condition: as good as new (ex-display), Year of construction: 2026, S&F drum chipper type ATH 220x530/3 Demonstration machine / trade fair machine / new machine Solid design with long service life Feed height: 200 mm Feed width: 500 mm Number of chipper knives: 2 pieces Number of counter knives: 1 piece Rotor diameter: 520 mm (solid steel rotor) Number of feed rollers: 3 pieces Throughput rate: up to approx. 20 rm/h * Chipping length: approx. 30 mm Chipper drive power: 45 kW or on request Feed roller drive power: 2 x 2.2 kW Operating/control voltage:400/220 V, 50 Hz Weight: 2,600 kg *depending on chipper length, kW main motor, number of knives, feed S&F chippers and drum chippers with horizontal infeed are used in many areas of the wood processing industry (sawmills, timber mills). Chippers from the ‘ATH’ series produce high-quality and homogeneous wood chips with a low proportion of fines from residual wood, for example as quality chips for the cellulose industry or as fuel chips for energy generation Advantages: - Maximum throughput - Low fines content - Low maintenance - Flexible use Dsdpfew I R Rnox Ahneuu - Customised production

Year of construction: 2009, condition: used, machine/vehicle number: 0301-230036, Kaltenbach drill saw system as a combination for use in light to heavy steel construction. Duedpfx Ahorr Sq Nsnsu With this Kaltenbach system, steel profiles can be drilled, center-punched and sawn to length in a single operation. Rolled profiles such as double T-steel, T-steel, U-steel, angle steel, hollow profiles and flat steel are processed here. The Kaltenbach drilling unit has an automatic tool changing device on three drilling spindles for five tool sizes each. The tools are positioned with high precision using ball screws and servomotors. The entire system is equipped with a length measuring device. Technical information KDXS 1215 drilling machine: - Working area min. 80 x 65 x 10 mm - Working area max. 1200 x 450 mm - 3 drilling units (vertical Y-axis, horizontal Z- and W-axis) each 11.0 kW frequency-controlled: 33.0 kW - Automatic tool changer (3x5) - Frequency-controlled drive power 78 kW - Working height 640 mm - Machine dimensions 6100 x 1300 x 3730 mm (LxWxH) - CNC control with Profiline 3 software Kaltenbach HDM 1432 High-performance circular saw as vertical saw with swivel bearing for high sawing performance of medium and heavy steel profiles, working area at 90° saw cut: 1200 x 450 mm, mitre adjustment for mitre cuts of -45°/90°/+35°, this circular saw system is equipped with a segment saw blade diameter 1430 mm. High cutting performance thanks to powerful drive NC-controlled cutting angle adjustment Feed via ball screw for ideal cutting results and short idle times

Condition: used, Year of construction: 2021, machine/vehicle number: HB 2022-A-073, pressing force: 300 t, Portal straightening press with 300 T capacity a) idle and pressing speed up to 17 mm/sec. b) opening speed up to 55 mm/sec c) table size 2500x1600mm d) open height 700 mm e) total size approx. LBH 4500 x 2300 x 3700 mm f) Oil temperature indicator on the tank g) Lubrication via grease nipple h) table in grid construction,with T grooves according to customer's request, otherwise 22mm i) operation on swivel arm, mounted on the bridge j) pressure adjustment from 50 T to 300 T via MONITOR k) bridge moves by two gear motors, via racks l) Cylinder moves to the left and to the right via toothed racks m) Machine body double painted n) Cylinder induction hardened Type of construction Press design PORTAL PRESS Thermally neutral 80 - 120 °C Number of operating sides 3 side Forces Pressing force max. 3,000 kN Free ripping force max. 500 kN Pressure build-up time Closed die Steel to steel Max. 3 sec. Dimensions Max. Opening width 700 mm Stroke and min. opening 700 mm/ 0 mm Table height above floor approx. 9ß0 mm Height above floor (headroom) approx. 3700 mm Hall height min. 5.000 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.8 mm/m Weight Total weight of press without operating materials and table plate approx. 22 T Speeds Fast closing with 17 mm sec. Pressing speed 8 mm sec. Opening 55 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel after max. 78 db(A) DIN 45635-T16-KL3 Hydraulics Number of pressing cylinders 1 pc. Operating pressure max. 350 bar Pressing pressure build-up time 02. mz sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH approx. 93 L/min Oil volume approx. HLPD 46 MW 900 liters Ambient temperature max. 45 °C Oil temperature max. 55 °C Electrical system Dusdpfxsh Agnuo Ahnju Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Hydraulic connection Main motor IE3 22 kW Total connection Approx. 30 kW

Condition: good (used), Hurco VMX64 / 40T Serial No. M64406503066FHA Year of manufacture: 2006 Spindle hours: approx. 4,200 h Power-on hours: approx. 5,900 h !!! Control upgraded to WINMAX (software version 2016, 09.01.393.53) !!! DXF option and network connection Travel distances: X: 1625 mm Y: 860 mm Z: 760 mm Clamping surface: 1675 x 890 mm Table load capacity: 2,500 kg Dujdoym R T Hspfx Ahnou Power: 15.0 kW Max. torque: 237 Nm Spindle/table distance: 150 - 910 mm Weight: 15,000 kg Dimensions (W x D x H): 6340 x 4400 x 3150 mm Features: - BigPlus spindle with 10,000 rpm - KNOLL band filter system - High-pressure coolant (IKZ) 20 bar - Tool magazine (hydraulic chain magazine), 40 slots - SK40 spindle - Chip conveyor - 6 NC hydraulic vices ATORN (125mm) The machine is in very good condition and ready for immediate use. All backlash has been adjusted, so the geometry is excellent. The control has been upgraded to WINMAX. Price plus loading costs of €1,500 For transport, a truck with 3 m width is required!

Condition: used, Year of construction: 2009, spindle diameter 125 mm x-travel 1.500 mm y-travel 1.250 mm z-travel 1.000 mm table surface area 1.000 x 1.250 mm w-travel 550 mm workpiece weight 6.000 kg quill stroke 550 mm tool taper ISO 50 number of spindle speeds 5-3.700 U/min. max. torque 2012 Nm feed speeds 1-6000 (x-Achse) mm/min feed speeds 1-6000 (y-Achse) mm/min Dedpfx Ahjwdta Ejnjuu feed speeds 1-6000 (z-Achse) mm/min rapid traverse x/y/z 15/ 15/ 15 m/min dimensions of the machine ca. 7,51 x 5,07 x 3,33 m 63 kVA Equipment/ Accessories: - CNC control Siemens 840 D - 60 ATC - Coolant system with high-pressure pump 30 l/min.- 20 bar - documentation

Condition: ready for operation (used), Year of construction: 2018, cutting diameter 300 mm saw band length 3660 x 27 x 0.9 mm capacity 90 degrees: flat 320 x 290 mm capacity 45 degrees: round 290 mm capacity 45 degrees: flat 260 x 280 mm capacity 60 degrees: round 200 mm capacity 60 degrees: flat 180 x 170 mm coolant capacity ca. 100 l Control SPS total power requirement 2.4 kW AC weight 904 kg range L-W-H 2410 x 1920 x 2020 mm in good conditions Original price approx. 22.000 euros Dusdpfx Ahjx A H T Hjneu Special price on request - in checked conditions - machinevideo - ?v=LAhu_AI9J5A Features: - Robust electro-hydraulic miter band saw, fully automatic (INDUSTRIAL) * Fully automatic with automatic material feed * Material feed unit with recirculating ball screws - Includes PLC MITSUBISHI control unit * 20 programs, each with 15 cutting lengths + number of pieces programmable - For angles from 0° to 60°, with ball-bearing rotary table * Mitre cuts up to 45° possible in automatic mode * Mitre cuts up to 60° possible in semi-automatic mode * Manual mitre adjustment * Stepless adjustment of the mitre angle - Saw blade guides made of carbide plates - Saw feed continuously adjustable via fine throttle - Strong machine bed and torsion-free saw frame - Stepless speed adjustment of the saw blade - Coolant device - Operating instructions for machine + control system * Special accessories included: - 1x PEGAS chip conveyor